Vacon 100 FLOW Installation guide

Type
Installation guide

This manual is also suitable for

vacon 100 industrial
vacon 100 flow
ac drives
installation manual
ip00 drive modules
®
®
PREFACE
Document ID: DPD01665C
Date: 15.2.2016
ABOUT THIS MANUAL
This manual is copyright of Vacon Ltd. All Rights Reserved. The manual is subject to change
without prior notice.
ABOUT THE PRODUCT
This manual describes the Vacon 100 IP00 Drive Module. The drive has a power range of
75-800 kW, and a voltage range of 208-240 V, 380-500 V, or 525-690 V. The drive is available
in 4 different enclosure sizes: MR8, MR9, MR10 and MR12. The enclosure class of the drive is
IP00, and that is why the drive must be installed in a cabinet or other enclosure after
delivery.
Fig. 1: Examples of the Vacon 100 IP00 drive module
PREFACE VACON · 3
24-HOUR SUPPORT +358 (0)201 212 575 · EMAIL: [email protected]
VACON · 4
TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205
TABLE OF CONTENTS
Preface
About this manual 3
About the product 3
1 Approvals 7
2 Safety 9
2.1 The safety symbols used in the manual 9
2.2 Warning 9
2.3 Caution 10
2.4 Grounding and earth fault protection 11
2.5 Using an RCD or an RCM device 12
3 Receiving the delivery 13
3.1 Package label 13
3.2 Type designation code 14
3.3 The contents of the delivery 14
3.4 Removing the packaging and lifting the AC drive 15
3.4.1 Weight of the AC drive 15
3.4.2 Lifting the IP00 drive module 15
3.5 "Product modified" label 18
3.6 Disposal 19
4 Mounting dimensions 20
4.1 Dimensions of MR8, IP00 20
4.2 Dimensions of MR9, IP00 21
4.3 Dimensions of MR10 and MR12, IP00 22
5 Installation into cabinet 25
5.1 General information 25
5.1.1 General information about the installation, MR8-MR9 25
5.1.2 General information about the installation, MR10 26
5.1.3 General information about the installation, MR12 29
5.2 Mechanical installation 31
5.2.1 Installing the IP00 drive module into the cabinet 32
5.2.2 Cooling and free space around the AC drive 34
6 Power cabling 36
6.1 Cable dimensioning and selection 36
6.1.1 Cable and fuse sizes 36
6.1.2 Cable and fuse sizes, North America 43
6.2 Brake resistor cables 48
6.3 Preparing for the cable installation 50
6.4 Cable installation 51
6.4.1 Enclosure sizes MR8 and MR9 51
6.4.2 Enclosure sizes MR10 and MR12 55
TABLE OF CONTENTS VACON · 5
24-HOUR SUPPORT +358 (0)201 212 575 · EMAIL: [email protected]
7 Control unit 64
7.1 Control unit components 64
7.2 Control unit cabling 65
7.2.1 Selection of the control cables 65
7.2.2 Control terminals and DIP switches 66
7.3 Fieldbus connection 70
7.3.1 Using fieldbus through an Ethernet cable 71
7.3.2 Using fieldbus through an RS485 cable 72
7.4 Installation of option boards 75
7.4.1 The installation procedure 76
7.5 Installation of a battery for the Real Time Clock (RTC) 77
7.6 Galvanic isolation barriers 77
8 Commissioning and additional instructions 79
8.1 Commissioning safety 79
8.2 Operation of the motor 80
8.2.1 Checks before starting the motor 80
8.3 Measuring the cable and motor insulation 80
8.4 Installation in an IT system 80
8.4.1 The EMC jumper in MR8 81
8.4.2 The EMC jumper in MR9 82
8.4.3 The EMC jumper in MR10 and MR12 83
8.5 Maintenance 86
8.5.1 Maintenance intervals 86
8.5.2 Replacing the fans of the AC drive 87
8.5.3 Downloading the software 91
9 Technical data, Vacon
®
100 95
9.1 AC drive power ratings 95
9.1.1 Mains voltage 208-240 V 95
9.1.2 Mains voltage 380-500 V 96
9.1.3 Mains voltage 525-690 V 97
9.1.4 Overload capability 97
9.1.5 Brake resistor ratings 98
9.2 Vacon
®
100 - technical data 102
10 Technical data, Vacon
®
100 FLOW 107
10.1 AC drive power ratings 107
10.1.1 Mains voltage 208-240 V 107
10.1.2 Mains voltage 380-500 V 108
10.1.3 Mains voltage 525-690 V 109
10.1.4 Overload capability 109
10.2 Vacon
®
100 FLOW - technical data 111
11 Technical data on control connections 116
11.1 Technical data on control connections 116
VACON · 6 TABLE OF CONTENTS
TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205
1 APPROVALS
Here are the approvals that have been granted to this Vacon product.
Find the EC Declaration of Conformity on the next page.
APPROVALS VACON · 7
24-HOUR SUPPORT +358 (0)201 212 575 · EMAIL: [email protected]
1
EC DECLARATION OF CONFORMITY
We
Manufacturer’s name: Vacon Oyj
Manufacturer’s address: P.O. Box 25
Runsorintie 7
FIN-65381 Vaasa
Finland
hereby declare that the product
Product name: Vacon 100 AC drive
Model Designation: Wall-Mounted Drives:
Vacon 0100 3L 0003 2...0310 2
Vacon 0100 3L 0003 4...0310 4
Vacon 0100 3L 0003 5...0310 5
Vacon 0100 3L 0004 6...0208 6
Vacon 0100 3L 0007 7...0208 7
IP00 Drive Modules:
Vacon 0100 3L 0140 2...0310 2
Vacon 0100 3L 0140 5...1180 5
Vacon 0100 3L 0080 7...0820 7
Enclosed Drives:
Vacon 0100 3L 0140 5...1180 5
Vacon 0100 3L 0080 7...0820 7
has been designed and manufactured in accordance with the following
standards:
Safety: EN 61800-5-1: 2007
EN 60204-1: 2006 + A1: 2009 (as
relevant)
EMC: EN 61800-3: 2004 + A1: 2012
EN 61000-3-12: 2011
and conforms to the relevant safety provisions of the Low Voltage
Directive (2006/95/EC) and EMC Directive 2004/108/EC.
It is ensured through internal measures and quality control that the
product conforms at all times to the requirements of the current
Directive and the relevant standards.
In Vaasa, 11th of January, 2016
Vesa Laisi
President
The year the CE marking was affixed: 2009
VACON · 8 APPROVALS
1
TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205
2 SAFETY
2.1 THE SAFETY SYMBOLS USED IN THE MANUAL
This manual contains warnings and cautions, which are identified with safety symbols. The
warnings and cautions give important information on how to prevent injury and damage to
the equipment or your system.
Read the warnings and cautions carefully and obey their instructions.
Table 1: The safety symbols
The safety symbol Description
WARNING!
CAUTION!
HOT SURFACE!
2.2 WARNING
WARNING!
Do not touch the components of the power unit when the drive is connected to
mains. The components are live when the drive is connected to mains. A contact
with this voltage is very dangerous.
WARNING!
Do not touch the motor cable terminals U, V, W, the brake resistor terminals or the
DC terminals when the drive is connected to mains. These terminals are live when
the drive is connected to mains, also when the motor does not operate.
WARNING!
Do not touch the control terminals. They can have a dangerous voltage also when
the drive is disconnected from mains.
SAFETY VACON · 9
24-HOUR SUPPORT +358 (0)201 212 575 · EMAIL: [email protected]
2
WARNING!
Before you do electrical work, make sure that there is no voltage in the
components of the drive.
WARNING!
To do work on the terminal connections of the drive, disconnect the drive from
mains and make sure that the motor has stopped. Wait 5 minutes before you open
the cabinet door or the cover of the drive. Then use a measuring device to make
sure that there is no voltage. The terminal connections and the components of the
drive are live 5 minutes after it is disconnected from mains and the motor has
stopped.
WARNING!
Before you connect the drive to mains, make sure that the front cover and the cable
cover of the drive are closed. The connections of the AC drive are live when the
drive is connected to mains.
WARNING!
Disconnect the motor from the drive if an accidental start can be dangerous. When
there is a power-up, a power break or a fault reset, the motor starts immediately if
the start signal is active, unless the pulse control for Start/Stop logic is selected. If
the parameters, the applications or the software change, the I/O functions
(including the start inputs) can change.
WARNING!
Wear protective gloves when you do mounting, cabling or maintenance operations.
There can be sharp edges in the AC drive that can cause cuts.
2.3 CAUTION
CAUTION!
Do not move the AC drive. Use a fixed installation to prevent damage to the drive.
CAUTION!
Do not make measurements when the AC drive is connected to mains. It can cause
damage to the drive.
CAUTION!
Make sure that there is reinforced protective ground connection. It is mandatory,
because the touch current of the AC drives is more than 3.5 mA AC (refer to EN
61800-5-1). See chapter 2.4 Grounding and earth fault protection.
CAUTION!
Do not use spare parts that are not from the manufacturer. Using other spare parts
can cause damage to the drive.
VACON · 10 SAFETY
2
TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205
CAUTION!
Do not touch the components on the circuit boards. Static voltage can cause
damage to these components.
CAUTION!
Make sure that the EMC level of the AC drive is correct for your mains. See chapter
8.4 Installation in an IT system. An incorrect EMC level can cause damage to the
drive.
CAUTION!
Prevent radio interference. The AC drive can cause radio interference in a domestic
environment.
NOTE!
If you activate the autoreset function, the motor starts automatically after an
automatic fault reset. See the Application Manual.
NOTE!
If you use the AC drive as a part of a machine, the machine manufacturer must
supply a mains disconnection device (refer to EN 60204-1).
2.4 GROUNDING AND EARTH FAULT PROTECTION
CAUTION!
The AC drive must always be grounded with a grounding conductor that is
connected to the grounding terminal that is identified with the symbol
. Not using
a grounding conductor can cause damage to the drive.
The touch current of the drive is more than 3.5 mA AC. The standard EN 61800-5-1 tells that
1 or more of these conditions for the protective circuit must be true.
The connection must be fixed.
a)
The protective grounding conductor must have a cross-sectional area of minimum 10
mm
2
Cu or 16 mm
2
Al. OR
b)
There must be an automatic disconnection of the mains, if the protective grounding
conductor breaks. See chapter 6 Power cabling. OR
c)
There must be a terminal for a second protective grounding conductor in the same
cross-sectional area as the first protective grounding conductor.
SAFETY VACON · 11
24-HOUR SUPPORT +358 (0)201 212 575 · EMAIL: [email protected]
2
Table 2: Protective grounding conductor cross-section
Cross-sectional area of the phase conductors (S)
[mm
2
]
The minimum cross-sectional area of the protective
grounding conductor in question [mm
2
]
S ≤ 16 S
16 < S ≤ 35 16
35 < S S/2
The values of the table are valid only if the protective grounding conductor is made of the
same metal as the phase conductors. If this is not so, the cross-sectional area of the
protective grounding conductor must be determined in a manner that produces a
conductance equivalent to that which results from the application of this table.
The cross-sectional area of each protective grounding conductor that is not a part of the
mains cable or the cable enclosure, must be a minimum of:
•
2.5 mm
2
if there is mechanical protection, and
•
4 mm
2
if there is not mechanical protection. If you have cord-connected equipment,
make sure that the protective grounding conductor in the cord is the last conductor to be
interrupted, if the strain-relief mechanism breaks.
Obey the local regulations on the minimum size of the protective grounding conductor.
NOTE!
Because there are high capacitive currents in the AC drive, it is possible that the
fault current protective switches do not operate correctly.
CAUTION!
Do not do voltage withstand tests on the AC drive. The manufacturer has already
done the tests. Doing voltage withstand tests can cause damage to the drive.
2.5 USING AN RCD OR AN RCM DEVICE
The drive can cause a current in the protective grounding conductor. You can use a residual
current-operated protective (RCD) device, or a residual current-operated monitoring (RCM)
device to give protection against a direct or an indirect contact. Use a type B RCD or RCM
device on the mains side of the drive.
NOTE! You can download the English and French product manuals with applicable safety, warning and caution
information from
http://drives.danfoss.com/knowledge-center/technical-documentation/.
REMARQUE Vous pouvez télécharger les versions anglaise et française des manuels produit contenant l'en-
semble des informations de sécurité, avertissements et mises en garde applicables sur le site http://
drives.danfoss.com/knowledge-center/technical-documentation/.
VACON · 12 SAFETY
2
TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205
3 RECEIVING THE DELIVERY
Before a Vacon
®
AC drive is sent to the customer, the manufacturer makes many tests on
the drive. However, after you remove the packaging, examine the drive for transport
damages.
If the drive was damaged during the shipping, speak to the cargo insurance company or the
carrier.
To make sure that the contents of the delivery is correct and complete, compare the type
designation of the product to the type designation code. See Chapter 3.2 Type designation
code.
3.1 PACKAGE LABEL
To make sure that the delivery is correct, compare your order data to the data on the
package label. If the delivery does not agree with your order, speak to the vendor
immediately.
A B
C
H
I
D
F
G
E
VACON100-3L-0205-5+IP00
Fig. 2: The package label of Vacon AC drives
A. The batch ID
B. The order number of Vacon
C. The type designation code
D. The serial number
E. The mains voltage
F. The nominal output current
G. The IP class
H. The application code
I. The order number of the customer
RECEIVING THE DELIVERY VACON · 13
24-HOUR SUPPORT +358 (0)201 212 575 · EMAIL: [email protected]
3
3.2 TYPE DESIGNATION CODE
The type designation code of Vacon is made of standard codes and option codes. Each part of
the type designation code agrees to the data in your order. The code can have this format, for
example:
VACON0100-3L-0385-5-FLOW+IP00
Table 3: The description of the parts in the type designation code
Code Description
VACON0100 The product family: VACON0100 = the Vacon 100 product family
3L Input/Function: 3L = A 3-phase input
0385 The drive rating in amperes. For example, 0385 = 385 A
5 The mains voltage:
2 = 208-240 V
5 = 380-500 V
7 = 525-690 V
FLOW The product:
(empty) = The Vacon 100 INDUSTRIAL AC drive
FLOW = The Vacon 100 FLOW AC drive
+IP00 The enclosure class of the AC drive is IP00.
3.3 THE CONTENTS OF THE DELIVERY
The contents of the delivery, MR8-MR9
•
The IP00 drive module with an integrated control unit
•
An accessories bag
•
Installation Manual, Application Manual and manuals for the options that you ordered
The contents of the delivery, MR10
•
The IP00 drive module with an integrated control unit
•
An accessories bag
•
The options module, if you ordered it with options
•
Installation Manual, Application Manual and manuals for the options that you ordered
The contents of the delivery, MR12
•
The IP00 drive module: 2 power units, 1 of them with an integrated control unit
•
An accessories bag
•
The options module, if you ordered it with options
•
A DC link cable
•
A set of optical fibre cables
•
Installation Manual, Application Manual and manuals for the options that you ordered
VACON · 14 RECEIVING THE DELIVERY
3
TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205
3.4 REMOVING THE PACKAGING AND LIFTING THE AC DRIVE
3.4.1 WEIGHT OF THE AC DRIVE
The weights of AC drives of different enclosure sizes are very different. It can be necessary
for you to use a lifting device to move the drive from its package.
Table 4: The weight of the AC drive, MR8-MR12
Enclosure size or item Weight [kg] Weight [lb]
MR8 IP00 drive module 62 137
MR9 IP00 drive module 104 228
MR10 IP00 drive module 205 452
MR10 IP00 drive module and the options module with the brake
chopper
252 556
MR10 IP00 drive module and the options module with the brake
chopper and the common mode filter
258 569
MR10 IP00 drive module and the options module with the brake
chopper, the common mode filter, and the du/dt filter
289 637
MR12 IP00 drive module 410 904
MR12 IP00 drive module and the options module with the brake
chopper
504 1111
MR12 IP00 drive module and the options module with the brake
chopper and the common mode filter
516 1138
MR12 IP00 drive module and the options module with the brake
chopper, the common mode filter, and the du/dt filter
578 1274
3.4.2 LIFTING THE IP00 DRIVE MODULE
The AC drive is delivered horizontally on a wooden pallet. Open the package only when you
install the drive. We do not recommend that you keep the drive in storage in the vertical
position.
LIFTING THE IP00 DRIVE MODULE, MR8 AND MR9
1 Remove the drive from the pallet where it was
bolted to.
2 Use a lifting device that is sufficiently strong for the
weight of the drive.
3 Put the lifting hooks symmetrically in a minimum of
2 holes.
RECEIVING THE DELIVERY VACON · 15
24-HOUR SUPPORT +358 (0)201 212 575 · EMAIL: [email protected]
3
4 The maximum lifting angle is 45 degrees.
≤45º≤45º
VACON · 16 RECEIVING THE DELIVERY
3
TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205
LIFTING THE IP00 DRIVE MODULE, MR10 OR MR12 WITHOUT THE OPTIONS MODULE
1 Make sure that the support is attached to the
bottom of the drive. It gives the terminals
protection when you lift the drive or put it vertically
on the floor.
A
A
A. The support / fixing bracket
2 Lift the drive with a lifting device. Put the lifting
hooks in the holes on the top of the cabinet. The
maximum lifting angle is 60 degrees.
3 After the lifting, you can remove the support if
necessary. You can also use it as a fixing bracket.
LIFTING THE IP00 DRIVE MODULE, MR10 OR MR12 WITH AN OPTIONS MODULE
1 Remove the drive from the package.
2 Use a lifting device that is sufficiently strong for the
weight of the drive.
3 Put the lifting hooks in the holes on the top of the
cabinet.
RECEIVING THE DELIVERY VACON · 17
24-HOUR SUPPORT +358 (0)201 212 575 · EMAIL: [email protected]
3
4 Lift the drive into a vertical position.
5 The maximum lifting angle is 60 degrees.
≤60º
3.5 "PRODUCT MODIFIED" LABEL
In the accessories bag, there is also a "product modified" label. The function of the label is to
tell the service personnel about the changes that are made in the AC drive. Attach the label
on the side of the AC drive to know where to find it. If you make changes in the AC drive, write
the change on the label.
Product modified
Date:
Date:
Date:
VACON · 18 RECEIVING THE DELIVERY
3
TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205
3.6 DISPOSAL
When the drive is at the end of its operation life, do not discard it as a part of municipal
waste. You can recycle the primary components of the drive. You must disassemble
some components before you can remove the different materials. Recycle the electrical
and electronic components as waste.
To make sure that the waste is recycled correctly, send the waste to a recycling centre.
You can also send the waste back to the manufacturer.
Obey the local and other applicable regulations.
RECEIVING THE DELIVERY VACON · 19
24-HOUR SUPPORT +358 (0)201 212 575 · EMAIL: [email protected]
3
4 MOUNTING DIMENSIONS
4.1 DIMENSIONS OF MR8, IP00
10
(0.37)
290 (11.42)
187 (7.34)
255 (10.04)
217 (8.54)
794 (31.26)
683 (26.89)
663 (26.10)
18
(0.71)
172 (6.75)
343 (13.50)
216 (8.49)
11
(0.43)
15
(0.59)
Ø9 (0.35)
Ø9
(0.35)
Ø22
(0.87)
Ø11 (0.43)
A
Fig. 3: The dimensions of the AC drive, MR8, [mm (in)]
A. An optional main connector cover for the
cabinet installation
VACON · 20 MOUNTING DIMENSIONS
4
TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120

Vacon 100 FLOW Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI