Rugged Ridge 17235.54 Installation guide

Brand
Rugged Ridge
Model
17235.54
Type
Installation guide

Rugged Ridge 17235.54 is a lower switch panel compatible with 2011+ JK/JKU models. It allows for the installation of five rocker switches, providing the user with control over various electrical accessories. The panel comes with pre-cut switch pockets that can be trimmed to ensure a snug fit for the switches. The installation process involves wiring the switches to the desired output, removing the center console cover and lower console panel, and then installing the switch panel using the provided tape.

Rugged Ridge 17235.54 is a lower switch panel compatible with 2011+ JK/JKU models. It allows for the installation of five rocker switches, providing the user with control over various electrical accessories. The panel comes with pre-cut switch pockets that can be trimmed to ensure a snug fit for the switches. The installation process involves wiring the switches to the desired output, removing the center console cover and lower console panel, and then installing the switch panel using the provided tape.

Copyright © 2016 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Lower Switch Panel; 2011+ JK/JKU
Page 1/3
Part # 17235.54
17235.84
OMIX-ADA® TECHNICAL SUPPORT
PHONE: M-F 8am - 5pm EST 1-800-449-6649 | EMAIL: [email protected]
FOR WARRANTY INFORMATION VISIT: www.Omix-Ada.com
CONTENTS:
• Lower Switch Panel (1)
TOOLS REQUIRED:
• Hobby Knife
• Plastic Trim Tool
Lower Switch Panel x 1 Rocker Switch x 5
A hazardous situation which, if not avoided, could result in minor or moderate
injury. You can be moderately hurt and may also suffer property damage if you
do not follow instructions.
CAUTION
!
Included with 17235.84 only
Copyright © 2016 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Lower Switch Panel; 2011+ JK/JKU
Page 2/3
3. FOR AUTO TRANS: With vehicle in 4L, fully engage
emergency brake, turn key to RUN position, and put
transmission in NEUTRAL.
FOR MANUAL TRANS: With vehicle in 4L, fully engage
emergency brake and put transmission in 4th gear.
2. Wire switches to desired output and install in Lower
Switch Panel.
1. Using a hobby knife with a sharp blade, cut outer
edge of switch pockets. Test t switch in each pocket.
Trim accordingly.
Cutting/Sharp Edge Hazard: Sharp
blade. Handle with care. Cut slowly
to ensure best possible tment.
CAUTION
!
Copyright © 2016 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Lower Switch Panel; 2011+ JK/JKU
Page 3/3
6. Remove red backing on tape and install Lower
Switch Panel. Ensure all clips engage, apply pressure
to tape area, and hold for 30 seconds. Reinstall center
console cover.
FOR AUTO TRANS: Put transmission in PARK. Turn key to
OFF position.
5. Slide center console cover backwards and remove
lower console panel by gently prying off with a
plastic trim tool.
4. Remove center console cover by gently pulling out
along bottom edges to release retaining clips.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Rugged Ridge 17235.54 Installation guide

Brand
Rugged Ridge
Model
17235.54
Type
Installation guide

Rugged Ridge 17235.54 is a lower switch panel compatible with 2011+ JK/JKU models. It allows for the installation of five rocker switches, providing the user with control over various electrical accessories. The panel comes with pre-cut switch pockets that can be trimmed to ensure a snug fit for the switches. The installation process involves wiring the switches to the desired output, removing the center console cover and lower console panel, and then installing the switch panel using the provided tape.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers