2. Rugged Ridge
  3. Interior Courtesy Lighting Kit

Rugged Ridge Interior Courtesy Lighting Kit Installation guide

  • Hello! I've reviewed the instructions for the Omix-Ada LED Lighting System 11250.09. This document details how to install the LED tubes in your vehicle, connect the power, and use the remote to control the lighting modes. I'm ready to answer your questions about the installation process, features, and usage of your new lighting system.
  • How do I disconnect the battery?
    Where do I place the 9" LED Tubes?
    How do I change lighting modes?
    Where do I place the 15" LED Tubes?
    What the function of PAUSE button in remote?
Copyright © 2016 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Interior LED Lighting System
Page 1/3
Part # 11250.09
OMIX-ADA® TECHNICAL SUPPORT
PHONE: M-F 8am - 5pm EST 1-800-449-6649 | EMAIL: [email protected]
FOR WARRANTY INFORMATION VISIT: www.Omix-Ada.com
CONTENTS:
• 9” LED Tube (4)
• 15” LED Tube (2)
• Remote (1)
• Connector Block (1)
• Mounting Tab (12)
• Hook and Loop Tape (1)
Mounting Tab x 12
Hook and Loop Tape x 1
Remote x 1 Connector Block x 1
15” LED Tube x 2
9” LED Tube x 4
A hazardous situation which, if not avoided, could result in serious injury or death.
You can be killed or seriously hurt if you do not follow instructions.
WARNING
!
Copyright © 2016 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Interior LED Lighting System
Page 2/3
3. Place one 9” LED Tube under each front seat. Attach
two Mounting Tabs to each LED Tube and remove
red tape backing. Press and hold each Mounting Tab
to bottom of seat for 30 seconds.
2. Place one 9” LED Tube under dashboard on each
side. Attach two Mounting Tabs to each LED Tube
and remove red tape backing. Press and hold each
Mounting Tab to metal bar underneath dashboard
for 30 seconds.
1. Disconnect battery, removing negative cable rst.
Connect red wire lead to positive terminal of battery
by routing wire through rubber grommet in rewall.
Connect black wire lead to 10 mm ground stud in
driver side footwell. Reconnect battery.
When removing battery cables do
not touch positive and negative
terminals together.
WARNING
!
Copyright © 2016 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
Interior LED Lighting System
Page 3/3
5. Plug all wires into Connector Block and power on
Interior LED Lighting System by pressing “POWER” on
supplied Remote. Switch between all lighting modes
using “MODE” buton. “PAUSE” keeps color from
changing or pulsing. To resume, press “PAUSE” button
again. Align all LED Tubes to properly light each area.
6. Run all wires under carpet and tuck underneath
edge of center console. Hide Connector Block
behind dashboard as shown on right. If desired,
attach Hook and Loop tape to back of Remote and
front of lower console panel.
4. Attach two Mounting Tabs to each 15” LED Tube
and remove red tape backing. Place one LED Tube
under body tub lip on each side of rear cargo area.
Press and hold for 30 seconds.
/