WaterWorks DSLS10 Installation guide

Brand: WaterWorks

Model: DSLS10

Type: Installation guide

STYLE No. DSLS30

Dash Gooseneck Three Hole

Deck Mounted Lavatory Faucet

with Metal Lever Handles

STYLE No. DSLS10

Dash Low Profile Three Hole

Deck Mounted Lavatory Faucet

with Metal Lever Handles

INSTALLATION GUIDELINES

PAGE 1 OF 4 | UPDATED ON 2.21.2023

PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM

IMPORTANT:

To ensure this product is installed properly, you must read and

follow these guidelines.

The owner/user of this product must keep this information for

future reference.

This product must be installed by a professional licensed

contractor.

Be sure your installation conforms to federal state, and local

codes. In the State of Massachusetts, all installations must

comply with the rules and regulations set forth within 248 CMR.

Inspect this product to ensure you have all the parts required

for proper installation. Product is sold partially assembled but

shown fully disassembled for illustrative and service purposed

only.

Use only a strap wrench or protected/smooth-jaw wrench on

any finished surface.

The use of certain plumber’s putty may stain stone or tile

surfaces.

If further assistance is required, please contact Product Support

at 1-800-927-2120 Monday through Friday, 8am – 6pm EST.

Refer to the separate Service Parts Documents for available

replacement parts.

TECHNICAL DETAILS:

STYLE DETAIL SPECIFICATION

ALL DECK THICKNESS 1/4” [6mm] MIN

1-9/16” [40mm] MAX

ALL DRAIN DEPTH 3/8” [10mm] MIN

2-5/8” [67mm] MAX

ALL DRAIN HOLE DIAMETER Ø1-3/4” [44mm]

ALL DRAIN STYLE PUSH TOUCH

ALL FITTINGS HOLE DIAMETER Ø1-3/8” [35mm]

ALL HANDLE SPREAD 8" [203mm] MIN

12” [305mm] MAX

ALL HANDLE TURN ANGLE QUARTER TURN

ALL INLET CONNECTION 1/2" Male with

Supply Nut

DSLS01

SPOUT REACH

5-3/4” [145mm]

DSLS20 6-1/16” [154mm]

ALL CARTRIDGE VALVE MATERIAL CERAMIC

ALL WATER PRESSURE RANGE 20psi [1.5 bar] MIN

85psi [6.0 bar] MAX

ALL WATER PRESSURE RECOMMENDED 45psi [3.0 bar]

STYLE No. DSLS30

Dash Gooseneck Three Hole

Deck Mounted Lavatory Faucet

with Metal Lever Handles

STYLE No. DSLS10

Dash Low Profile Three Hole

Deck Mounted Lavatory Faucet

with Metal Lever Handles

INSTALLATION GUIDELINES

PAGE 2 OF 4 | UPDATED ON 2.21.2023

PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM

SPOUT ESCUTCHEON

[DO NOT REMOVE]

RUBBER WASHER

[DO NOT REMOVE]

SHANK

RUBBER

WASHER

METAL

WASHER NUT

RUBBER WASHER

TEE

RUBBER WASHER

NUT

METAL WASHER

RUBBER WASHER

MOUNTING

SURFACE

SHANK

RUBBER WASHER*

ESCUTCHEON

SPOUT

* If desired, a bead of

caulk or a clear

silicone may be

applied where the

ESCUTCHEON

contacts the

mounting surface.

HANDLE STEM

[DO NOT REMOVE]

SCREW

[DO NOT REMOVE]

SIDEBODY

HANDLE

FINISHED SCREW

[CAUTION]

1. Remove the TEE, NUT and lower deck WASHERS

from the SPOUT SHANK. Do NOT remove the

WASHER from the ESCUTHCEON.

2. Insert the SHANK through the hole on the

mounting surface then re-attach the WASHERS,

NUT, and TEE and securely tighten the NUT.

3. Carefully unthread the FINISHED SCREW then pull

the HANDLE up. Do NOT remove the HANDLE

STEM.

PLASTIC

BUSHING

[DO NOT

REMOVE]

PLASTIC SPACER,

RUBBER WASHER,

METAL WASHER,

NUT

SIDEBODY

TRIM CONNECTOR

O-RING

ESCTUCHEON

TRIM NUT

[16mm WRENCH]

4. Unthread and remove the TRIM NUT, remove the

ESCUTCHEON with the O-RING, unthread and

remove the TRIM CONNECTOR then fully thread

the NUT down the SIDEBODY.

CAUTION: Do NOT remove the PLASTIC BUSHING

on the TRIM NUT

PLASTIC SPACER,

RUBBER WASHER,

METAL WASHER,

NUT

SIDEBODY

TRIM CONNECTOR

5. Thread the TRIM CONNECTOR back onto the

SIDEBODY until it stops and let is rest on the

mounting surface then hand-tighten the NUT

against the underside of the mounting surface.

CAUTION: Do NOT over tighten the NUT to allow

for proper handle alignment during HANDLE

installation.

SIDEBODY

MOUNTING

SURFACE

TRIM

CONNECTOR

O-RING*

ESCTUCHEON

TRIM NUT

[16mm WRENCH]

* If desired, a bead of

caulk or a clear

silicone may be

applied where the

ESCUTCHEON

contacts the

mounting surface.

6. Place the ESCUTCHEON and O-RING over the TRIM

CONNECTOR then thread and securely tighten the

TRIM NUT into the TRIM CONNECTOR;

STYLE No. DSLS30

Dash Gooseneck Three Hole

Deck Mounted Lavatory Faucet

with Metal Lever Handles

STYLE No. DSLS10

Dash Low Profile Three Hole

Deck Mounted Lavatory Faucet

with Metal Lever Handles

INSTALLATION GUIDELINES

PAGE 3 OF 4 | UPDATED ON 2.21.2023

PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM

SCREW

HANDLE STEM

NUT

SIDEBODY

BUSHING

HANDLE

FINISHED SCREW

[CAUTION]

SIDEBODY

[2ND]

SCREW

HANDLE

[2ND]

SIDEBODY

[2ND]

SUPPLY HOSE*

[2ND]

TEE

SUPPLY HOSE*

SIDEBODY

* WARNING:

ENSURE THE HOSES ARE NOT

PINCHED/KINKED

7. Place the HANDLE onto the HANDLE STEM, thread

and securely tighten the FNISHED SCREW, ensure

the HANDLE is in the desired orientation then

securely tighten the NUT of the SIDEBODY.

8. Repeat Steps 3 through 7 to install the second

HANDLE.

9. Connect the SIDEBODIES to the TEE using the

SUPPLY HOSES provided. Securely tighten the

HOSES and ensure they are not pinched/kinked.

TAILPIECE NUT

TAILPIECE

RUBBER

WASHER

LOWER DRAIN

BODY

10. Remove the TAILPIECE from the LOWER DRAIN

BODY.

LOWER DRAIN

GASKET

[DO NOT REMOVE]

LOWER DRAIN

BODY

UPPER DRAIN

GASKET

DRAIN FLANGE

SCREW

DRAIN STOPPER

[CAN BE DISCARDED]

[5/32" OR

4mm HEX

KEY]

11. Unthread and remove the DRAIN STOPPER and

LOWER DRAIN BODY from the DRAIN FLANGE

The UPPER DRAIN GASKET can be discarded.

CAUTION: Do NOT discard the LOWER DRAIN

GASKET.

LAVATORY

DRAIN

FLANGE*

* USE PUTTY OR A

CLEAR ADHESIVE

SILICONE

12. Set the DRAIN FLANGE in the lavatory [SOLD

SEPARATELY] using putty or a clear adhesive

silicone.

STYLE No. DSLS30

Dash Gooseneck Three Hole

Deck Mounted Lavatory Faucet

with Metal Lever Handles

STYLE No. DSLS10

Dash Low Profile Three Hole

Deck Mounted Lavatory Faucet

with Metal Lever Handles

INSTALLATION GUIDELINES

PAGE 4 OF 4 | UPDATED ON 2.21.2023

PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM

LOWER DRAIN

BODY

LOWER DRAIN

GASKET*

DRAIN

FLANGE*

SCREW

[5/32" OR

4mm HEX

KEY]

* PUTTY OR A CLEAR

ADHESIVE MAY BE

USED TO ENSURE A

WATER-TIGHTE SEAL

BETWEEN THE

GASKET AND

LAVATORY

TAILPIECE NUT

LOWER DRAIN

BODY

TAILPIECE

RUBBER

WASHER

DRAIN

STOPPER

SUPPLY VALVE

[NOT SUPPLIED]

P- TRAP

[NOT

SUPPLIED]

TAILPIECE

SUPPLY TUBE

[NOT SUPPLIED]

SUPPLY NUT

[SUPPLIED]

13. Re-install the LOWER DRAIN BODY making sure to

use the GASKET provided. Ensure the GASKET

makes a full seal on the underside of the lavatory

then securely tighten the SCREW.

14. Re-install the DRAIN STOPPER then the TAILPIECE

using the WASHER and NUT provided.

15. Make final P-TRAP [sold separately] and SUPPLY

VALVE [sold separately] connections.

AERATOR

TOOL

AERATOR

1. REMOVE AERATOR

3. CLOSE DRAIN

2. TURN ON WATER

AND OPERATE

HANDLES

16. Removed the AERATOR, turn on the water to flush

out the supply lines, and inspect all connections for

leaks. Close the DRAIN.to ensure it functions

properly then turn off the water and re-install the

AERATOR.

NOTE: 2-3 Seconds of residual water is typical on

large gooseneck faucets.

WaterWorks DSLS10 Installation guide

WaterWorks DSLS10 Installation guide

WaterWorks DSLS10 Installation guide

Related papers

Other documents