Wahl 1770MX Quick start guide

Wahl
Brand
Wahl
Model
1770MX
Type
Quick start guide

This manual is also suitable for

Initial Checkout
These simple steps will verify the correct operation of your Heat-Prober:
1) With no probe plugged in, switch the Function Switch to the Normal Monitor
(N) position.
2) After the display stabilizes, you will see
This indicates an “open line” at the probe interface.
3) Plug your probe into the Heat-Prober.
4) The Display will indicate the temperature of the probe. In most
circumstances, this will be room temperature.
5) If you have a TCMR model Heat-Prober, the switch on the front of the meter
will change the display from Fahrenheit to Centigrade.
Additional Checks
If you wish to verify the Peak Hold function, use the following procedures:
6) Switch the Function Switch to the Peak Hold (P) position.
7) Heat the probe.
8) When the reading stabilizes, note the indicated temperature.
9) Cool the probe.
10) Note that the indicated temperature does not change as the probe cools.
11) Switch the Function Switch to the Normal Monitor (N)
position to read the true temperature of the probe.
If the unit does not behave as expected, the first thing to check is the power.
1) If your model comes with an external charger, plug it in and recheck the
unit. Allow battery to charge before using.
2) If your model has a 9 volt battery, remove the battery compartment securing
screw, open the compartment, and remove the battery.
3) Check the voltage (9 volts, nominally) and replace if necessary.
4) Reinstall the battery, close the compartment, and recheck the Heat-Prober
for proper operation.
Refer to the Instruction Manual for additional information.
Palmer Wahl Instrumentation Group
234 Old Weaverville Road
Asheville, North Carolina 28804-1228
(800) 421-2853 • Fax (828) 658-0728
email: [email protected]
www.palmerwahl.com
HEAT-PROBER
PORTABLE THERMOCOUPLE
THERMOMETERS
Heat-Prober
Thermocouple
Models 2500/1370 and 3200/1770
WD1026 Rev A
03/26/08
-
-
OL
-
Controls and Displays
Thank you for choosing the Wahl Heat-Prober 2500/1370 Series
Meter. This “Quick Start” manual is designed to familiarize you
with the basic operation of all the Heat-Prober Thermocouple
models.
The following Table summarizes the features and characteristics of all the
Thermocouple Heat-Prober models.
Power Source
Model T/C
Type
Measurement
Range
Display
Type 1 9 Volt
Battery
Rechargeable
Battery Pack
External
Transformer
2500M K -100° to 2500° F LED √ √
2500MX K -100° to 2500° F LCD √ √
2500MVX K -100° to 2500° F LCD √
1370M K -70° to 1370° C LED √ √
1370MX K -70° to 1370° C LCD √ √
1370MVX K -70° to 1370° C LCD √
3200M S 77° to 3200° F LED √ √
3200MX S 77° to 3200° F LCD √ √
3200MVX S 77° to 3200° F LCD √
1770M S 25° to 1770° C LED √ √
1770MX S 25° to 1770° C LCD √ √
1770MVX S 25° to 1770° C LCD √
Display Type
LED: Light Emitting Diode – Usable in dark environments,
uses more power than LCD.
LCD: Liquid Crystal Display – Very low power consumption,
not usable in dark environments.
The features and controls of these models vary, depending on which model you
have. The following data and illustrations will identify which model the item
applies to by “tagging” each item as follows:
Tag Applicable Models
M: 2500M, 1370M, 3200M, 1770M
MX: 2500MX, 1370MX, 3200MX, 1770MX
MVX: 2500MVX, 1370MVX, 3200MVX, 1770MVX
Untagged items apply to all models.
Thermocouple
Probe Socket
LCD Display
Function
Switch
Battery
Compartment
Wrist Strap
Attachment
Compartment
Securing
Screw
Charger
Socket
  • Page 1 1
  • Page 2 2

Wahl 1770MX Quick start guide

Wahl
Brand
Wahl
Model
1770MX
Type
Quick start guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents