2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. BAPI
  7. BA-WSK Weather Shade Kit

BAPI BA-WSK Weather Shade Kit, BA-WSK Operating instructions

  • Hello! I've reviewed the provided instructions for the BAPI Weather Shade Kit BA/WSK. This document describes how to mount the kit and its components to help protect temperature and humidity sensors from solar heat. I'm ready to answer any questions you may have about the installation or features described in the document.
  • What is the purpose of the Weather Shade Kit?
    What does the pre-assembled Weather Shade Kit include?
    What should I do if the weather shade appears loose?
    What should I do if weather shade does not sit parallel to the wall?
Instructions
Weather Shade Kit (BA/WSK)
Building Automation Products, Inc., 750 North Royal Avenue, Gays Mills, WI 54631 USA
Tel:+1-608-735-4800 • Fax+1-608-735-4804 • E-mail:[email protected] • Web:www.bapihvac.com
rev. 06/17/21
38242_ins_weather_shade
1 of 2
A
Weather Shade
Cone
B
Probes
C
Probe Caps
D
Wingnut
E
Clamp without
Bracket
F
Clamp with
Bracket
G
Locknuts
Overview & Identication
External temperature and humidity sensors are
aected by solar heat gain. The BAPI Weather
Shade eectively reduces the solar heat gain,
improving the accuracy of the sensor.
The pre-assembled Weather Shade Kit includes
a shade and din rail bracket, two capped
mounting tubes, one adjustable clamp and one
adjustable clamp with bracket.
1. Mount Temp/Humidity sensor on a north
facing wall.
2. Screw Part B to top of enclosure. See note*
below.
3. Place Part E on Part B with screw facing up
and tighten hose clamp. Then screw on Part
C to top of Part B.
4. Place Part F on bottom probe with hose
clamp screw facing up and tighten hose
clamp screw.
5. Line up bracket to mounting surface and
tighten screw so bracket is ush with
mounting surface.
6. Obtain Part A and slide DIN rail through inner
slots of Parts E and F and push until it stops.
7. Screw Part D on to bolt of cone (Part A) and
fasten to Part F.
*Note: Part G provided if threads do not exist in
the enclosure.
**Note: If Weather Shade is swiveling, refer
to Step 5 and ensure bracket is ush with
mounting surface.
Mounting
Fig. 1: Mounting to the BAPI-Box 2 & BAPI-Box outdoor air sensors
C
E
B
F
Parts List
C
E
B
F
BAPI-Box 2 BAPI-Box
BAPI-Box 2 BAPI-Box
Instructions
Weather Shade Kit (BA/WSK)
Building Automation Products, Inc., 750 North Royal Avenue, Gays Mills, WI 54631 USA
Tel:+1-608-735-4800 • Fax+1-608-735-4804 • E-mail:[email protected] • Web:www.bapihvac.com
rev. 06/17/21
38242_ins_weather_shade
2 of 2
Possible Problem
Weather Shade appears loose or not
rmly mounted.
Weather shade does not sit parallel
to the wall
Diagnostics
Specications
Shade Material:
UV-stabilized Polycarbonate
Shade Material Ratings:
Flammability: UL 94
UV Exposure: UL746C
Reectivity: 87%
Emissivity: 0.90
Possible Solution
Tighten the hose clamps on the top and bottom clamps and make
sure the wing nut is tightened rmly against the bottom bracket.
Make sure the DIN rail is going through the INNER slot in both the top
and bottom clamps.
Specications subject to change without notice.
/