DIODE LED SPOTMOD® PUCK Installation guide

Brand
DIODE LED
Model
SPOTMOD® PUCK
Type
Installation guide
1 OF 4 IG122122-2.0
SPOTMOD® PUCK INSTALLATION GUIDE
SPOTMOD® PUCK
Installation Guide
DRY LOCATION
DIMMABLE
12VDC
IP20
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. Install in accordance with national and local electrical
code regulations.
2. This product is intended to be installed and serviced by a
qualified, licensed electrician.
3. Do not modify or disassemble this product beyond
instructions or the warranty will be void.
4. Do not use if there is any damage to the fixture or wiring.
Inspect periodically.
5. Do not install near areas with exposure to water.
6. Do not install in direct sunlight or damage to the LED
phosphor will occur.
7. Do not attempt to fix this product in the field.
8. Failure to follow safety warnings, and installation
instructions will void the warranty for this product.
SAFETY & WARNINGS
Input 12VDC Constant Voltage
Power
2.4W
Ambient Temp
†
Environment Damp/Indoor
QUICK SPECS / MODELS
† Do not install product in environment outside
listed temperature.
*NOT FOR USE WITHIN POOLS OR OTHER
HIGHLY CHLORINATED OR SALT WATER
ENVIRONMENTS.
2 OF 4 IG122122-2.0
SPOTMOD® PUCK INSTALLATION GUIDE
SPOTMOD® PUCK
Installation Guide
INSTALLATION
TURN POWER OFF AT CIRCUIT
BREAKER
SHOCK HAZARD! May result in serious
injury or death.
Turn power OFF at circuit breaker prior to
installation.
REQUIRED TOOLS
1
2
3
1. Phillips-head Screwdriver
2. Wire Stripper (Recommended)
3.  DETERMINE LOCATION TO INSTALL
COMPONENTS
1
3
2
Refer to SYSTEM DIAGRAMS

Driver
 

WIRE GAUGE & VOLTAGE DROP
Ensure applicable wire is installed between driver, fixture,
and any controls in between. When choosing wire, factor
in voltage drop, amperage rating, and type (in-wall rated,
wet location rated, etc.)
TEST CONNECTION
Prior to mounting, attach to Class 2
LED Driver, turn on power and test
connection to ensure system is
operating properly. Turn off power
again before mounting.
3 OF 4 IG122122-2.0
SPOTMOD® PUCK INSTALLATION GUIDE
SPOTMOD® PUCK
Installation Guide
4
INSTALLATION (CONT.)
SURFACE MOUNT SPOTMOD® PUCK

4.1
Route cords through ring, and screw mounting
ring to surface.
4.2
Pop puck into mounting ring.
4.3
5
TURN POWER ON AT CIRCUIT
BREAKER
6
ATTACH DRIVER AND LIGHTING
CONTROL.
Verify a compatible driver is installed.
1. Drill a hole through cabinet or shelf no larger than 2
13/64". A 2 1/8" is recommended
2. Pop puck off mounting ring, mount ring into hole with
screws.
3. 
4. 
Fig. 3 Fig. 4
(OPTIONAL) RECESSED MOUNTING (Fig. 3 & 4)
4 OF 4 IG122122-2.0
SPOTMOD® PUCK INSTALLATION GUIDE
SPOTMOD® PUCK
Installation Guide
The following diagrams are provided as example system designs. For information regarding larger systems or
systems not pictured below, please see our web page or contact technical support. Always review each component
installation guide for detailed and up-to-date wiring instructions. Install in accordance with national and local
electrical codes.
L
N
G*
N
LV+
V−
120VAC On/Off Switch Class 2 Low Voltage Driver2
Installed in Junction Box7
V+
V-
LED Tape Light / Fixture
8
Install appropriate wire gauge / type
V+
V-
AC Power
50/60Hz
INPUT
OUTPUT
Traditional ON/OFF Switch System
AC Power
50/60Hz
Compatible Dimming Control
or On/Off Switch5
LED Tape Light / Fixture8
L
Install appropriate wire gauge / type
OMNIDRIVE® Dimmable Driver6
Some dimmers may require an
additional neutral wire connection.
NNGND*
N
LV+
V−
V+
V−
V+
V−
INPUT
OUTPUT
Class 2 Low Voltage Driver2
Installed in Junction Box7
REIGN® 24V Dimmer System
OMNIDRIVE® Electronic Dimmable Driver
System
SWITCHEX® Dimmer/Driver System
G*
N
LV+
V−
Class 2 Low Voltage Driver3
Installed in Junction Box7
V- (Black)
Input Output
V+ (Red)
Install appropriate wire gauge / type
V+
V-
LED Tape Light / Fixture8
REIGN 12-24V Dimmer4
V+
V-
L
N
AC Power
50/60Hz
INPUT
OUTPUT













N (WHT)
120 VAC
~ 60Hz
V+ (RED)
V− (BLUE)
+
−
+
−
L (BLK)
SWITCHEX
(Dimmer + Driver)
LED ARRAY / FIXTURE
Ground (GRN)
Install applicable wire gauge / type
Install applicable wire gauge / type
SYSTEM DIAGRAMS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

DIODE LED SPOTMOD® PUCK Installation guide

Brand
DIODE LED
Model
SPOTMOD® PUCK
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents