Sony PMW-350K User manual

4-164-464-11(1)

Solid-State Memory

Camcorder

Operating Instructions

Before operating the unit, please read this manual thoroughly

and retain it for future reference.

PMW-350K

PMW-350L

Printed in Japan

Printed on recycled paper.

2

To reduce the risk of fire or

electric shock, do not

expose this apparatus to

rain or moisture.

To avoid electrical shock,

do not open the cabinet.

Refer servicing to qualified

personnel only.

Important Safety Instructions

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with dry cloth.

• Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

• Do not install near any heat sources such

as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that

produce heat.

• Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding-type

plug has two blades and a third grounding

prong. The wide blade or the third prong

are provided for your safety. If the

provided plug does not fit into your outlet,

consult an electrician for replacement of

the obsolete outlet.

• Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

• Only use attachments/accessories

specified by the manufacturer.

• Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or

objects have fallen into the apparatus, the

apparatus has been exposed to rain or

moisture, does not operate normally, or

has been dropped.

WARNING

Excessive sound pressure from earphones

and headphones can cause hearing loss.

In order to use this product safely, avoid

prolonged listening at excessive sound

pressure levels.

For the customers in the U.S.A.

This equipment has been tested and found

to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated

in a commercial environment. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area is likely to

cause harmful interference in which case the

user will be required to correct the

interference at his own expense.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

All interface cables used to connect

peripherals must be shielded in order to

comply with the limits for a digital device

pursuant to Subpart B of Part 15 of FCC

Rules.

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions: (1) this device may not cause

harmful interference, and (2) this device

must accept any interference received,

including interference that may cause

undesired operation.

WARNING

3

For the customers in Canada

This Class A digital apparatus complies with

Canadian ICES-003.

For the customers in Europe

This product with the CE marking complies

with the EMC Directive issued by the

Commission of the European Community.

Compliance with this directive implies

conformity to the following European

standards:

• EN55103-1: Electromagnetic

Interference(Emission)

• EN55103-2: Electromagnetic

Susceptibility(Immunity)

This product is intended for use in the

following Electromagnetic Environments: E1

(residential), E2 (commercial and light

industrial), E3 (urban outdoors), E4

(controlled EMC environment, ex. TV

studio).

The manufacturer of this product is Sony

Corporation, 1-7-1 Konan, Minato-ku,

Tokyo, Japan.

The Authorized Representative for EMC and

product safety is Sony Deutschland GmbH,

Hedelfinger Strasse 61, 70327 Stuttgart,

Germany.

For the State of California, USA only

Perchlorate Material - special handling may

apply, See

www.dtsc.ca.gov/hazardouswaste/

perchlorate

Perchlorate Material : Lithium battery

contains perchlorate.

For the customers in Taiwan only

Afin de réduire les risques

d’incendie ou

d’électrocution, ne pas

exposer cet appareil à la

pluie ou à l’humidité.

Afin d’écarter tout risque

d’électrocution, garder le

coffret fermé. Ne confier

l’entretien de l’appareil

qu’à un personnel qualifié.

AVERTISSEMENT

Une pression acoustique excessive en

provenance des écouteurs ou du casque

peut provoquer une baisse de l’acuité

auditive.

Pour utiliser ce produit en toute sécurité,

évitez l’écoute prolongée à des pressions

sonores excessi

Pour les clients au Canada

Cet appareil numérique de la classe A est

conforme à la norme NMB-003 du Canada.

Pour les clients en Europe

Ce produit portant la marque CE est

conforme à la Directive sur la compatibilité

électromagnétique (EMC) émise par la

Commission de la Communauté

européenne.

La conformité à cette directive implique la

conformité aux normes européennes

suivantes :

• EN55103-1 : Interférences

électromagnétiques (émission)

• EN55103-2 : Sensibilité

électromagnétique (immunité)

Ce produit est prévu pour être utilisé dans

les environnements électromagnétiques

suivants : E1 (résidentiel), E2 (commercial et

industrie légère), E3 (urbain extérieur) et E4

(environnement EMC contrôlé, ex. studio de

télévision).

AVERTISSEMENT

4

Le fabricant de ce produit est Sony

Corporation, 1-7-1 Konan, Minato-ku,

Tokyo, Japon.

Le représentant autorisé pour EMC et la

sécurité des produits est Sony Deutschland

GmbH, Hedelfinger Strasse 61, 70327

Stuttgart, Allemagne.

Um die Gefahr von Bränden

oder elektrischen Schlägen

zu verringern, darf dieses

Gerät nicht Regen oder

Feuchtigkeit ausgesetzt

werden.

Um einen elektrischen

Schlag zu vermeiden, darf

das Gehäuse nicht geöffnet

werden. Überlassen Sie

Wartungsarbeiten stets nur

qualifiziertem

Fachpersonal.

WARNUNG

Zu hoher Schalldruck von Ohrhörern und

Kopfhörern kann Gehörschäden

verursachen.

Um dieses Produkt sicher zu verwenden,

vermeiden Sie längeres Hören bei sehr

hohen Schalldruckpegeln.

Für Kunden in Europa

Dieses Produkt besitzt die CE-

Kennzeichnung und erfüllt die EMV-

Richtlinie der EG-Kommission.

Angewandte Normen:

• EN55103-1: Elektromagnetische

Verträglichkeit (Störaussendung)

• EN55103-2: Elektromagnetische

Verträglichkeit (Störfestigkeit)

Für die folgenden elektromagnetischen

Umgebungen: E1 (Wohnbereich), E2

(kommerzieller und in beschränktem Maße

industrieller Bereich), E3 (Stadtbereich im

Freien) und E4 (kontrollierter EMV-Bereich,

z.B. Fernsehstudio).

Der Hersteller dieses Produkts ist Sony

Corporation, 1-7-1 Konan, Minato-ku,

Tokyo, Japan.

Der autorisierte Repräsentant für EMV und

Produktsicherheit ist Sony Deutschland

GmbH, Hedelfinger Strasse 61, 70327

Stuttgart, Deutschland.

WARNUNG

Table of Contents

5

Table of Contents

Foreword .................................................................................................... 10

Before Use....................................................................................... 10

Chapter 1 : Overview

Features ...................................................................................................... 11

Using the CD-ROM ................................................................................... 12

Reading the CD-ROM Manuals...................................................... 12

System Requirements for Using the Applications .......................... 13

Software Installation ....................................................................... 13

Locations and Functions of Parts and Controls...................................... 14

Power Supply .................................................................................. 14

Accessory Attachments................................................................... 14

Operating and Connectors Section.................................................. 16

Monochrome LCD Panel ................................................................ 25

Auto Focus Lens (Supplied with the PMW-350K)......................... 26

Viewfinder....................................................................................... 27

Viewfinder Screen Display........................................................................ 29

Chapter 2 : Preparations

Preparing a Power Supply ........................................................................ 33

Using a Battery Pack....................................................................... 33

Using AC Power ............................................................................. 34

Attaching the Viewfinder .......................................................................... 35

Attaching the Supplied Viewfinder................................................. 35

Adjusting the Viewfinder Position.................................................. 35

Adjusting the Viewfinder Angle ..................................................... 36

Lifting Up the Viewfinder Barrel and Eyepiece ............................. 36

Adjusting the Viewfinder Focus and Screen................................... 37

Using the BKW-401 Viewfinder Rotation Bracket ........................ 37

Attaching a 5-inch Electronic Viewfinder ...................................... 38

Setting the Area of Use .............................................................................. 40

Setting the Date/Time of the Internal Clock ........................................... 41

Mounting and Adjusting the Lens............................................................ 41

Adjusting the Flange Focal Length................................................. 42

Table of Contents

6

Preparing the Audio Input System .......................................................... 43

Connecting a Microphone to the MIC IN Connector...................... 43

Connecting Microphones to the AUDIO IN Connectors................ 44

Attaching a UHF Portable Tuner (for a UHF Wireless Microphone

System) ..................................................................................... 45

Tripod Mounting ....................................................................................... 46

Connecting a Video Light ......................................................................... 47

Using the Shoulder Strap .......................................................................... 48

Adjusting the Shoulder Pad Position ....................................................... 49

Chapter 3 : Adjustments and Settings

Setting the Video Format .......................................................................... 50

Changing the Video Format............................................................ 51

Adjusting the Black Balance and the White Balance ............................. 51

Adjusting the Black Balance........................................................... 51

Adjusting the White Balance .......................................................... 52

Setting the Electronic Shutter................................................................... 55

Shutter Modes ................................................................................. 55

Selecting the Shutter Mode and Shutter Speed............................... 55

Changing the Reference Value for Automatic Iris Adjustment............ 57

Zooming ...................................................................................................... 58

Switching between Zoom Modes.................................................... 58

Using Manual Zoom ....................................................................... 58

Using Servo Zoom .......................................................................... 58

Adjusting the Focus ................................................................................... 58

Adjusting in Full MF Mode ............................................................ 58

Adjusting in MF Mode.................................................................... 59

Adjusting in AF Mode .................................................................... 59

Using Macro Mode ......................................................................... 59

Adjusting the Audio Level ........................................................................ 60

Manually Adjusting the Audio Levels of the Audio Inputs from the

AUDIO IN CH1/CH2 Connectors............................................ 60

Manually Adjusting the Audio Level of the MIC IN Connector .... 60

Recording Audio on Channels 3 and 4 ........................................... 61

Setting the Time Data................................................................................ 62

Setting the Timecode....................................................................... 62

Setting the User Bits........................................................................ 63

Synchronizing the Timecode........................................................... 63

Table of Contents

7

Checking Camcorder Settings and Status Information (Status Screens)

............................................................................................................... 65

Chapter 4 : Shooting

Handling S×S Memory Cards................................................................... 67

About S×S Memory Cards.............................................................. 67

Loading and Ejecting S×S Memory Cards ..................................... 68

Selecting the S×S Memory Card to Use ......................................... 69

Formatting (Initializing) S×S Memory Cards................................. 69

Checking the Remaining Recording Time...................................... 70

Restoring S×S Memory Cards ........................................................ 70

Basic Operations ........................................................................................ 71

Playing Recorded Clips................................................................... 72

Deleting Recorded Clips ................................................................. 73

Advanced Operations ................................................................................ 73

Recording Shot Marks..................................................................... 73

Setting OK Marks ........................................................................... 73

Starting to Record from Pre-stored Video (Picture Cache Function)

.................................................................................................. 74

Recording Time-lapse Video (Interval Rec Function).................... 75

Shooting Stop Motion Animations (Frame Rec Function) ............. 77

Shooting with Slow & Quick Motion ............................................. 78

Framing Shots with the Freeze Mix Function................................. 79

Chapter 5 : Clip Operations

Clip Playback ............................................................................................. 80

Thumbnail Screen ........................................................................... 80

Playing Clips ................................................................................... 82

Using Thumbnails to Search Inside Clips....................................... 83

Thumbnail Operations .............................................................................. 84

THUMBNAIL Menu Configuration............................................... 84

Basic THUMBNAIL Menu Operations.......................................... 85

Changing the Thumbnail Screen Type............................................ 85

Displaying Clip Properties .............................................................. 86

Adding and Deleting OK Marks (HD Mode Only) ........................ 87

Copying Clips ................................................................................. 87

Deleting Clips.................................................................................. 88

Displaying the Expand Thumbnail Screen...................................... 88

Displaying the Shot Mark Thumbnail Screen (HD Mode Only).... 89

Adding and Deleting Shot Marks (HD Mode Only)....................... 90

Changing Clip Index Pictures (HD Mode Only)............................. 90

Table of Contents

8

Dividing Clips (HD Mode Only) .................................................... 91

Chapter 6 : Menu and Detailed Settings

Setup Menu Organization and Levels...................................................... 92

Setup Menu Organization ............................................................... 92

Setup Menu Levels.......................................................................... 92

Basic Setup Menu Operations .................................................................. 94

Menu List.................................................................................................... 96

OPERATION Menu........................................................................ 96

PAINT Menu................................................................................. 109

MAINTENANCE Menu ............................................................... 115

FILE Menu.................................................................................... 127

Assigning Functions to Assignable Switches ......................................... 131

Functions that can be assigned to the ASSIGN. 0 switch............. 131

Functions that can be assigned to the ASSIGN. 2 switch............. 132

Functions that can be assigned to the ASSIGN. 1 and 3 switches, the

ASSIGNABLE 4 and 5 switches, and the COLOR TEMP. button

................................................................................................ 132

Functions that can be assigned to the RET button on the lens...... 134

Chapter 7 : Saving and Loading User Setting Data

Saving and Loading Settings................................................................... 135

Saving Setting Data....................................................................... 135

Loading Setting Data..................................................................... 136

Resetting a File after Changing Its Contents................................. 136

Saving and Loading Scene Files ............................................................. 137

Saving Scene Files ........................................................................ 137

Loading Scene Files ...................................................................... 137

Saving and Loading Lens Files............................................................... 138

Setting Lens File Data................................................................... 138

Saving Lens Files .......................................................................... 138

Loading Lens Files........................................................................ 138

Loading Lens Files Automatically................................................ 139

Chapter 8 : Connecting External Devices

Connecting External Monitors ............................................................... 140

Operating Clips with a Computer.......................................................... 142

Table of Contents

9

Connecting an External Device (i.LINK Connection).......................... 144

Recording the Camera Picture on an External Device.................. 144

Nonlinear Editing.......................................................................... 145

Recording External Input Signals ................................................. 145

Chapter 9 : Maintenance

Testing the Camcorder............................................................................ 147

Maintenance ............................................................................................. 147

Cleaning the Viewfinder ............................................................... 147

Note about the Battery Terminal................................................... 147

Operation Warnings................................................................................ 148

Appendix

Important Notes on Operation ............................................................... 155

Exchanging the Battery of the Internal Clock ...................................... 157

Specifications............................................................................................ 157

General.......................................................................................... 157

Camera Block................................................................................ 158

Audio Block .................................................................................. 158

Display .......................................................................................... 158

Media Block.................................................................................. 158

Inputs/Outputs............................................................................... 159

Lens Block (PMW-350K only)..................................................... 159

Supplied Accessories .................................................................... 159

Recommended Additional Equipment .......................................... 160

Chart of Optional Components and Accessories .................................. 162

About i.LINK ........................................................................................... 163

MPEG-2 Video Patent Portfolio License............................................... 164

Index.......................................................................................................... 165

Foreword

10

After purchasing the PMW-350K/350L Solid-

State Memory Camcorder, before operating, it is

necessary to set the area of use.

(Unless this setting is made, the camcorder will

not operate.)

For details of these settings, see “Setting the Area of

Use” (page 40).

Note

Before attaching/removing optional components or

accessories to/from the PMW-350K/350L (referred to as

“the camcorder”), be sure to turn the power of the

camcorder off.

Foreword

Before Use

Features

11

Chapter 1 Overview

2

/

3

-type full-HD (1920 × 1080) CMOS

image sensors

The PMW-350K/350L Solid-State Memory

Camcorder is provided with three newly

developed

2

/

3

-type “Exmor” CMOS image

sensors with approximately 207 million effective

pixels, for full HD resolution (1920 × 1080). The

new image sensor technology enables the capture

of very high-quality images, with a sensitivity of

F12 (59.94i) / F13 (50i) and an SN ratio of 59 dB.

S×S memory cards as recording media

Using S×S memory cards, the camcorder offers

nonlinear capabilities such as instant random

access and file-based operation.

Light weight, low power consumption

Design features such as CMOS image sensors,

custom video signal processing ICs, and S×S

memory card recording enable fanless operation

and power consumption of 15 W or less. The

camcorder’s light weight (3.2 kg (7 lb 0.88 oz))

and low center of gravity make it easy to carry on

the shoulder while ensuring superior stability.

HD recording using the “MPEG-2 Long

GOP” codec

The camcorder records 1920 × 1080, 1440 ×

1080, and 1280 × 720 HD images using “MPEG-

2 Long GOP” codec compression. It offers a

choice of bit rates: either 35 Mbps (HQ mode) or

25 Mbps (SP mode).

By utilizing an efficient compression format, the

camcorder records high-quality HD images for

long recording time of approx. 100 minutes at 35

Mbps (HQ mode) or approx. 140 minutes at 25

Mbps (SP mode) on a single 32-GB S×S memory

card.

Multi-format support

The camcorder supports interlace format

recording (1080/59.94i or 1080/50i), progressive

format recording (1080/29.97P, 1080/23.98P,

720/59.94P, 720/29.97P, 720/23.98P, or 1080/

25P, 720/50P, 720/25P), thus offering the

flexibility needed for worldwide HD recording.

(For 23.98P, native frequency recording is

possible.)

It also supports recording and playback of SD

signals (both NTSC and PAL). The camcorder

has an optional capability to record and play back

SD signals in DVCAM-AVI format (option

1)

),

and can output HD signals down-converted to

SD.

1) CBK-DV01

A special auto focus lens

The camcorder is provided with the

2

/

3

-type auto

focus lens, which ensures high-quality shooting

in all situations from wide angle to telephoto

(PMW-350K only).

A variety of functions for improved

performance under various shooting

conditions

• Picture Cache function

• Optical ND filters and electrical CC filters

• Hyper gamma

• Slow shutter function

• Frame Recording function

• Time lapse function (interval recording)

• Slow & quick motion function

• Freeze mix function

• Focus magnification function

• Image inversion function

• Assignable switches

• 3.5-inch high-resolutin color LCD viewfinder

• Remote control

Chapter1 Overview

Features

Using the CD-ROM

12

Chapter 1 Overview

Inherits unique features of XDCAM EX

series

The camcorder inherits the workflow features of

the XDCAM EX series, including thumbnail

display and metadata management, and improves

them by introducing an improved man-machine

interface.

XDCAM EX web sites

For information on XDCAM EX, visit the

following web sites:

United States

http://www.sony.com/xdcamex

Canada

http://www.sony.ca/xdcamex

Europe, Middle East, Africa, and Russia

http://www.sonybiz.net/xdcamex

Latin America

http://www.sonypro-latin.com/xdcamex

Australia

http://www.sony.com.au/xdcamex

Asia (except Korea, China, and Japan)

http://pro.sony-asia.com

Korea

http://bp.sony.co.kr/xdcamex

China

http://pro.sony.com.cn/minisite/XDCAMEX

Japan

http://www.sony.co.jp/XDCAMEX

Two CD-ROMs are supplied with the camcorder.

The CD-ROM labeled “Manuals for Solid-State

Memory Camcorder” contains the PDF files of

the Operating Instructions and Supplement for

the camcorder (Japanese, English, French,

German, Italian, Spanish and Chinese).

The CD-ROM labeled “Utility Software for

Solid-State Memory Camcorder and Recorder”

contains the following software:

S×S Device Driver Software

Driver for using S×S memory cards with a

computer having an ExpressCard slot.

Information on installation of the software is

included in the ReadMe (Japanese, English,

French, German, Italian, Spanish, and Chinese) in

PDF format.

XDCAM EX Clip Browsing Software

Application program for operating clips recorded

with XDCAM EX-series models on a computer.

Information on installation and operations of the

software is included in the User’s Guide

(Japanese, English, French, German, Italian,

Spanish, and Chinese) in PDF format.

Preparations

The following program must be installed on your

computer in order to read the operation manuals

contained on the CD-ROM.

Adobe Reader Version 6.0 or higher

Memo

If Adobe Reader is not installed, you can download it

from the following URL:

http://www.adobe.com/

Adobe and Adobe Reader are trademarks of Adobe

Systems Incorporated in the United States and/or other

countries.

Using the CD-ROM

Reading the CD-ROM Manuals

Using the CD-ROM

13

Chapter 1 Overview

To read the documents

Do the following:

1 Insert the CD-ROM in your CD-ROM

drive.

A cover page appears automatically in your

browser.

If it does not appear automatically in the

browser, double-click on the index.htm file

on the CD-ROM.

2 Select and click on the manual that you

wish to read.

This opens the PDF file.

Memo

The files may not be displayed properly, depending on

the version of Adobe Reader. In such a case, install the

latest version you can download from the URL

mentioned in “Preparations” above.

Note

If you have lost or damaged the CD-ROM, you can

purchase a new one to replace it. Contact a Sony service

representative.

The following operating conditions are

recommended for using the software recorded on

the CD-ROM:

S×S Device Driver Software

Applicable hardware

Computer conforming to ExpressCard/34 or

ExpressCard/54

OS

Microsoft Windows XP SP2 or later, Microsoft

Windows Vista, Microsoft Windows 7, or Mac

OS X v10.4.9 or later

For support information on the driver, refer to the

following URL:

http://www.sony.net/S×S-Support/

XDCAM EX Clip Browsing Software

For the operating requirements, visit the web sites

shown in “XDCAM EX web sites” (page 12) or

refer to the User’s Guide contained in the

CD-ROM.

Do the following to install the software on the

CD-ROM on your computer:

1 Insert the CD-ROM in your CD-ROM

drive.

A cover page appears automatically in your

browser.

If it does not appear automatically in the

browser, double-click on the index.htm file

on the CD-ROM.

2 Select and click on the software that you

wish to install.

The installer for the software starts up.

Follow the displayed instructions:

For details, refer to the User’s Guide or ReadMe of

the software.

Uninstalling an application program

Windows computer

Choose “Start,” “Control Panel” then “Add or

Remove Programs” and specify the program to be

deleted.

Macintosh computer

Drop the folder of the software (default:

/Application/XDCAM EX Clip Browser) into

Trash.

System Requirements for Using

the Applications

Software Installation

Locations and Functions of Parts and Controls

14

Chapter 1 Overview

a LIGHT switch

Determines how a video light connected to the

LIGHT connector (see page 15) is turned on and

off.

AUTO: When the POWER switch of the video

light is in the on position, the video light is

turned on automatically while the camcorder

is recording.

MANUAL: You can turn the video light on or off

manually, using its own switch.

Note

When the camcorder is set for recording in Picture Cache

mode, it is not possible to turn on the light before

operation to start recording is carried out (or while data

is being stored in memory).

b POWER switch

Turns the main power supply on and off.

c DC IN (DC power input) connector

(XLR type, 4-pin, male)

To operate the camcorder from an AC power

supply, connect an optional DC power cord to this

terminal and then connect the cord to the DC

output terminal of the BC-L70, BC-M150, or

another battery charger.

d DC OUT 12V (DC power output)

connector (4-pin, female)

Supplies power for an optional WRR-860A/861/

862 UHF Synthesized Diversity Tuner

(maximum 0.5 A).

Do not connect any equipment other than the

UHF synthesized diversity tuner.

e Battery attachment shoe

Attach a BP-GL95/GL65/L80S/L60S Battery

Pack. Alternatively, you can attach an AC-

DN2B/DN10 AC Adaptor to operate the

camcorder on AC power supply.

For details, see “Preparing a Power Supply”

(page 33).

For details, see “Attaching a UHF Portable Tuner

(for a UHF Wireless Microphone System)”

(page 45).

Note

For your safety, and to ensure proper operation of the

camcorder, Sony recommends the use of the following

battery packs: BP-GL95, BP-GL65, BP-L60S, and

BP-L80S.

a Shoulder strap fitting

Attach the supplied shoulder strap (see page 48).

b Light fitting shoe

Attach an optional accessory such as a video light

(see page 47).

Locations and Functions

of Parts and Controls

Power Supply

23154

Accessory Attachments

Locations and Functions of Parts and Controls

15

Chapter 1 Overview

c Viewfinder front-to-back positioning

lever

To adjust the viewfinder position in the front-to-

back direction, loosen this lever and the LOCK

knob. After adjustment, retighten this lever and

the LOCK knob.

d Viewfinder left-to-right positioning ring

Loosen this ring to adjust the left-to-right position

of the viewfinder (see page 35).

e Viewfinder fitting shoe

Attach the viewfinder.

f VF (viewfinder) connector (26-pin,

rectangular)

Connect the cable of the supplied viewfinder.

g VF (viewfinder) connector (20-pin,

round)

Connect the cable of the optional DXF-51 or

DXF-20W viewfinder.

For connecting the DXF-51, optional parts are

required. Consult a Sony service representative for

information about connecting the DXF-51.

h Lens mount securing rubber

After locking the lens in position using the lens

locking lever, fit this rubber over the lower of the

two projections. This fixes the lens mount,

preventing it from coming loose.

i Viewfinder front-to-back positioning

knob (LOCK knob)

Loosen this knob to adjust the front-to-back

position of the viewfinder (see page 35).

j Fitting for optional microphone holder

Fit an optional CAC-12 Microphone Holder (see

page 44).

k Shoulder pad

Raise the shoulder pad fixing lever to adjust the

position in the front-to-rear direction. Adjust the

position for maximum convenience when

operating the camcorder on your shoulder (see

page 49).

l LIGHT (video light) connector (2-pin,

female)

A video light with a maximum power

consumption of 50 W, such as the Anton Bauer

Ultralight 2 or equivalent can be connected (see

page 47).

m Lens cable clamp

Clamp a lens cable.

n MIC IN (microphone input) (+48 V)

connector (XLR type, 5-pin, female)

Connect a stereo microphone to this connector.

The power (+48 V) is supplied via this connector.

o LENS connector (12-pin)

Connect a lens cable to this connector.

Note

When connecting or disconnnecting the lens

cable to this connector, power off the camcorder

first.

p Tripod mount

When using the camcorder on a tripod, attach the

tripod adaptor (optional).

q Lens mount (special bayonet mount)

Attach the lens.

Consult a Sony service representative for

information about available lenses.

r Lens locking lever

After inserting the lens in the lens mount, rotate

the lens mount ring with this lever to lock the lens

in position.

After locking the lens, be sure to use the lens

mount securing rubber to prevent the lens from

becoming detached.

s Lens mount cap

Remove by pushing up the lens locking lever.

When no lens is mounted, keep this cap fitted for

protection from dust.

Locations and Functions of Parts and Controls

16

Chapter 1 Overview

Front

a REC START (recording start) button

Press to start recording. Press it again to stop

recording. The effect is the same as that of the

REC button on the lens.

b SHUTTER selector

Set to ON to use the electronic shutter. Push to

SELECT to switch the shutter speed or shutter

mode setting. When this switch is operated, the

new setting appears on the viewfinder screen for

about three seconds.

For details, see “Setting the Electronic Shutter”

(page 55).

c FILTER selector

Switches between four ND filters built into this

camcorder.

When this selector is used, the new setting

appears on the viewfinder screen for about three

seconds.

You can change a MAINTENANCE menu

setting so that different white balance settings can

be stored for different FILTER selector positions.

This allows you to automatically obtain optimum

white balance for the current shooting conditions

in linkage with the filter selection.

For details, see “Adjusting the White Balance”

(page 52).

d MENU knob

Changes the item selection or a setting within the

menu (see page 94).

e AUTO W/B BAL (automatic white/

black balance adjustment) switch

Activates the automatic white/black balance

adjustment functions.

WHITE: Adjust the white balance automatically.

If the WHITE BAL switch (see page 18) is

set to A or B, the white balance setting is

stored in the corresponding memory. If the

WHITE BAL switch is set to PRST, the

automatic white balance adjustment function

does not operate.

BLACK: Adjust the black set and black balance

automatically.

You can use the AUTO W/B BAL switch even

when the ATW (Auto Tracing White Balance)

function is operating.

If you push the switch to the WHITE side once

more during the automatic white balance

adjustment, the adjustment is cancelled and the

white balance setting returns to the original

setting.

If you push the switch to the BLACK side once

more during the automatic black balance

adjustment, the adjustment is cancelled and the

black balance setting returns to the original

setting.

f MIC (microphone) LEVEL control

Adjusts the input level of audio channels 1, 2, 3

and 4 (see page 60).

Operating and Connectors Section

FILTER selector

setting

ND filter

1 CLEAR

2

1

/

4

ND (attenuates light to

approximately

1

/

4

)

3

1

/

16

ND (attenuates light to

approximately

1

/

16

)

4

1

/

64

ND (attenuates light to

approximately

1

/

64

)

FILTER selector

setting

ND filter

Locations and Functions of Parts and Controls

17

Chapter 1 Overview

Right side (near the front)

a ASSIGN. (assignable) 1/2/3 switches

You can assign the desired functions to these

switches on OPERATION >Assignable SW in

the setup menu (see page 131).

EZ Mode is assigned to the ASSIGN. 1 switch,

and Off is assigned to the ASSIGN. 2/3 switches

as the factory default setting.

The ASSIGN.1/3 switches are provided with an

indicator to show whether a function is assigned

to the switch (ON) or not (OFF).

b COLOR TEMP. (color temperature)

button

Press to light the button and change the color

temperature for shooting (factory default setting).

You can use this as an assignable switch (see

page 131).

c ALARM (alarm tone volume

adjustment) knob

Controls the volume of the warning tone that is

output via the built-in speaker or optional

earphones. When the knob is turned to the

minimum position, no sound can be heard.

However, if MAINTENANCE >Audio >Min

Alarm Volume in the setup menu is set to [Set],

the alarm tone is audible even when this volume

control is at the minimum position.

d MONITOR (monitor volume

adjustment) knob

Controls the volume of the sound other than the

warning tone that is output via the built-in speaker

or earphones. When the knob is turned to the

minimum position, no sound can be heard.

e MONITOR (audio monitor selection)

switches

By means of combinations of the two switches,

you can select audio that you want to hear through

the built-in speaker or earphones.

Position of down-side switch: CH-1/2

Position of down-side switch: CH-3/4

a) By connecting stereo headphones to the EARPHONE

jack, you can hear the audio in stereo. (Under

MAINTENANCE >Audio in the setup menu,

Headphone Out must be set to STEREO.)

Position of up-side

switch

Audio output

CH-1/CH-3 Channel 1 audio

MIX Channels 1 and 2 mixed

audio (stereo)

a)

CH-2/CH-4 Channel 2 audio

Position of up-side

switch

Audio output

CH-1/CH-3 Channel 3 audio

MIX Channels 3 and 4 mixed

audio (stereo)

a)

CH-2/CH-4 Channel 4 audio

ALARM

Minimum Maximum

Locations and Functions of Parts and Controls

18

Chapter 1 Overview

f ASSIGN. (assignable) 0 switch

You can assign the desired function to this switch

on OPERATION >Assignable SW in the setup

menu (see page 132).

Off is assigned to this switch when the camcorder

is shipped from the factory.

This is a momentary type switch. Each press of

the switch turns the function assigned to this

switch on or off.

g GAIN selector

Switches the gain of the video amplifier to match

the lighting conditions during shooting. The gains

corresponding to the L, M, and H settings can be

selected on OPERATION >Gain Switch in the

setup menu (see page 104). (The factory settings

are L=0 dB, M=6 dB, and H=12 dB.)

When this switch is adjusted, the new setting

appears on the viewfinder screen for about three

seconds.

h OUTPUT/DCC (output signal/dynamic

contrast control) switch

Switches the video signal output from the camera

module, between the following two.

BARS: Output the color bar signal.

CAM: Output the video signal being shot. When

this is selected, you can switch DCC

1)

on and

off.

1) DCC (Dynamic Contrast Control): Against a very

bright background with the iris opening adjusted to the

subject, objects in the background will be lost in the

glare. The DCC function will suppress the high

intensity and restore much of the lost detail and is

particularly effective in the following cases.

• Shooting people in the shade on a sunny day

• Shooting a subject indoors, against a background

through a window

• Any high contrast scene

i WHITE BAL (white balance memory)

switch

Controls adjustment of the white balance.

PRST: Adjust the color temperature to the preset

value (the factory default setting: 3200K).

Use this setting when you have no time to

adjust the white balance.

A or B: Recall the white balance adjustment

settings already stored in A or B. Push the

AUTO W/B BAL switch (see page 16) on

the WHITE side, to automatically adjust the

white balance, and save the adjustment

settings in memory A or memory B.

B (ATW

1)

): When this switch is set to B and

OPERATION >White Setting >White

Switch<B> is set to [ATW] in the setup

menu, ATW is activated.

You can use the AUTO W/B BAL switch

even when ATW is in use.

When this switch is adjusted, the new setting

appears on the viewfinder screen for about three

seconds.

1) ATW (Auto Tracing White Balance): The white

balance of the picture being shot is adjusted

automatically for varying lighting conditions.

j MENU ON/OFF switch

To use this switch, open the cover.

This switch is used to display the menu on the

viewfinder screen or the test signal screen. Each

time the switch is pushed down, the menu screen

is turned on and off.

The function of this switch is the same as that of

the MENU button in the thumbnail screen

operations section.

k STATUS ON/SEL/OFF (menu display

on/page selection/display off) switch

MENU CANCEL/PRST (preset) /

ESCAPE switch

When the menu is not displayed, this switch

functions as the STATUS ON/SEL/OFF switch.

When the menu is displayed, the switch functions

as the MENU CANCEL/PRST/ESCAPE switch.

(To use the MENU CANCEL/PRST/ESCAPE

switch, open the cover.)

Use the STATUS ON/SEL/OFF switch in the

following way.

ON/SEL: Each time this switch is pushed

upward, a window to confirm the menu

settings and status of the camcorder appears

on the viewfinder screen (see page 65). The

window consists of five pages, which are

switched each time the switch is pushed

upward. Each page is displayed for about 10

seconds.

OFF: To clear the page immediately after

display, push this switch down to the OFF

position.

Use the MENU CANCEL/PRST/ESCAPE in the

following way.

Locations and Functions of Parts and Controls

19

Chapter 1 Overview

CANCEL/PRST: Pushing this switch up to this

position after a setting is changed in the setup

menu displays the message to confirm

whether the previous settings are cancelled.

Pushing this switch up to this position again

cancels the previous settings.

Pushing this switch up to this position before

a setting is changed in the setup menu or after

a setting change is cancelled in the setup

menu displays the message to confirm

whether the setting is reset to the initial

value.

Pushing this switch up to this position again

resets the settings to the initial value.

ESCAPE: Use this switch when the menu page,

which has a hierarchical structure, is opened.

Each time the switch is pushed to this

position, the page returns to one stage higher

in the hierarchy.

l Cover

Open this cover to use the MENU ON/OFF

switch or the MENU CANCEL/PRST/ESCAPE

switch.

Right side (near the rear)

a Built-in speaker

The speaker can be used to monitor E-E

1)

sound

during recording, and playback sound during

playback. The speaker also sounds alarms to

reinforce visual warnings (see page 148).

If you connect earphones to the EARPHONE

jack, the speaker output is suppressed

automatically.

1) E-E: Abbreviation of “Electric-to-Electric”. In E-E

mode, video and audio signals input to the camcorder

are output after passing through internal electric

circuits only. This can be used to check input signals.

b Monochrome LCD panel

Displays remaining battery capacity, remaining

media capacity, audio levels, time data, and so on

(see page 25).

Locations and Functions of Parts and Controls

20

Chapter 1 Overview

c WARNING indicator

Lights up or flashes when an abnormality occurs

(see page 148).

d ACCESS lamp

Lights up when data is written to or read from the

recording media.

e Protection cover of the audio control

section

Open to access the audio control section (see

page 21).

f Protection cover of the thumbnail

screen operations section

Open to access the thumbnail screen operations

section (see page 21).

g F REV (fast reverse) button and

indicator

This plays back at high speed in the reverse

direction. The playback speed changes in the

order ×4 t ×15 t ×24 with each press of the

button. The indicator lights during high-speed

playback in the reverse direction.

h PLAY/PAUSE button and indicator

Press this button to view play back video images

using the viewfinder screen or the LCD monitor.

The indicator lights during playback.

Press this button again during playback to pause,

outputting a still image. At this time the indicator

flashes at a rate of once per second.

Pressing the F REV or F FWD button during

playback or pause starts high speed playback in

the forward or reverse direction.

i F FWD (fast forward) button and

indicator

This plays back at high speed in the forward

direction. The playback speed changes in the

order ×4 t ×15 t ×24 with each press of the

button. The indicator lights during high-speed

playback in the forward direction.

j PREV button

This jumps to the first frame of the current clip.

If you press this together with the F REV button,

the jump is to the first frame of the first recorded

clip on the recording media.

If you press this button twice in rapid succession,

the jump is to the first frame of the last preceding

clip (or the first frame of the current clip when no

preceding clips exist).

k STOP button

Press this button to stop playback.

l NEXT button

This jumps to the first frame of the next clip.

If you press this together with the F FWD button,

the jump is to the first frame of the last recorded

clip on the recording media.

m EXPAND (expand function) button

If you press this button when the thumbnail

screen is displayed, the duration of the selected

clip is divided into fractions, and the first frame of

each of the divisions is shown in a further

thumbnail display (expand function). For an HD

recorded MP4 clip, its duration is divided into 12.

If an SD recorded AVI clip comprises multiple

files, the divisions are displayed for the individual

files.

For MP4 clips, each time you press this button the

division is repeated. Hold down the SHIFT button

and press this button to step back through the

division process.

n HOLD (display hold) button

Pressing this button instantly freezes the time data

displayed in the monochrome LCD panel. (The

timecode generator continues running.) Pressing

this button again releases the hold.

For details of the counter display, see page 25.

o RESET/RETURN button

Resets the value shown in the time counter

display in the monochrome LCD panel.

According to the settings of the PRESET/

REGEN/CLOCK switch (see page 22) and the

F-RUN/SET/R-RUN switch (see page 21), this

button resets the display as follows.

Settings of switches To re set

DISPLAY switch:

COUNTER

Counter to 0:00:00:00

DISPLAY switch:

TC

PRESET/REGEN/

CLOCK switch:

PRESET

F-RUN/SET/R-RUN

switch: SET

Timecode to 00:00:00:00

Page is loading ...

Sony PMW-350K User manual

This manual is also suitable for

Sony PMW-350K User manual

Related papers

Other documents