City Theatrical Legacy 5750 and 5752 D4 HP Quick start guide

Brand
City Theatrical
Model
Legacy 5750 and 5752 D4 HP
Type
Quick start guide

City Theatrical Legacy 5750 and 5752 D4 HP is a high-power DMX dimmer designed to control a wide range of lighting fixtures, including LED, incandescent, and flicker candles. With its flexible input and output options, the D4 HP can be easily integrated into any DMX system.

The D4 HP features eight output channels, each capable of delivering up to 15 Amps. This makes it ideal for controlling high-wattage fixtures or multiple fixtures on a single channel. The dimmer also offers a variety of dimming curves and modes, allowing you to customize the dimming performance to suit your specific needs.

City Theatrical Legacy 5750 and 5752 D4 HP is a high-power DMX dimmer designed to control a wide range of lighting fixtures, including LED, incandescent, and flicker candles. With its flexible input and output options, the D4 HP can be easily integrated into any DMX system.

The D4 HP features eight output channels, each capable of delivering up to 15 Amps. This makes it ideal for controlling high-wattage fixtures or multiple fixtures on a single channel. The dimmer also offers a variety of dimming curves and modes, allowing you to customize the dimming performance to suit your specific needs.

D4 HP Dimmer Quick Start Guide
PN5750
PN5752
D4 HP Dimmer
The D4 HP Dimmer can be quickly set up to control your lights:
1. Connect your D4 HP Dimmer to your DMX controller by using either the DMX ve pin input, or the RJ-45 DMX input.
DMX out can be either the ve pin XLR output, or the RJ-45 output. Note, there can only be a total of one DMX input,
and one DMX output per device.
2. Connect your load to the output channels with either screw terminals (PN5750) or Anderson Powerpole connectors
(PN5752).
3. Connect 100 - 240VAC to the D4 HP Dimmer power input.
4. Set a DMX start address to meet the needs of your installation.
5. Use your bump buttons to check that your output is correctly wired. The DMX LED will blink when not receiving DMX,
and will be solid when receiving DMX.
6. See the full manual for information on dimming curves, modes, and smoothing, which will insure optimum dimming
quality when set to suit your specic dimming needs (LED, incandescent, icker candles, etc).
Turn power off before removing or connecting your loads
5750 Output Terminals
5752 Output Terminals
Connecting 12V Three Color RGB Tape
12 Volt three color LED tape is provided with a single +12VDC circuit and a –VDC circuit for each color.
1. Connect the +12VDC circuit to any one of the eight + output terminals. The + terminals are bussed, and provide con-
stant voltage. Note that some tape comes pre-wired with Black wire for the +12VDC circuit while other tape comes
pre-wired with White wire.
2. Connect the R, G and B circuits each to one of the four – output terminals (in the case of four color tape, connect the
A or W circuit to the fourth – output terminal). The – terminals are the PWM dimmed outputs of the D4 Dimmer. Note
that some tape comes with the R, G and B (and A or W) circuits in a different order than others.
3. Select the LED Curve for each dimmer channel used. (Curve dip switches on-on for each channel)
4. Power up your Dimmer and test your load connections with the bump buttons.
5. If you wish to change the PWM frequency, use RDM or the MOD DIP switch to select the TV/Film mode desired.
Connecting Single Color Tape
12 Volt single color tape is provided with a single +VDC circuit and a –VDC circuit.
1. Connect the +VDC circuit to one of the + output terminals and connect the -VDC circuit to the accompanying – output
terminal.
2. For LED tape, select the LED Curve (Curve dip switches on-on for each channel) and set LED smoothing, if needed.
(see manual)
3. If you wish to change the PWM frequency, use RDM or the MOD DIP switch to select the TV/Film mode desired.
Scan the QR Code for quick reference to the D4 HP User Manual
  • Page 1 1
  • Page 2 2

City Theatrical Legacy 5750 and 5752 D4 HP Quick start guide

Brand
City Theatrical
Model
Legacy 5750 and 5752 D4 HP
Type
Quick start guide

City Theatrical Legacy 5750 and 5752 D4 HP is a high-power DMX dimmer designed to control a wide range of lighting fixtures, including LED, incandescent, and flicker candles. With its flexible input and output options, the D4 HP can be easily integrated into any DMX system.

The D4 HP features eight output channels, each capable of delivering up to 15 Amps. This makes it ideal for controlling high-wattage fixtures or multiple fixtures on a single channel. The dimmer also offers a variety of dimming curves and modes, allowing you to customize the dimming performance to suit your specific needs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents