TP-LINK C400S2 Smart Wire-Free Security Camera System User guide

Brand: TP-LINK

Model: C400S2 Smart Wire-Free Security Camera System

Type: User guide

This manual is also suitable for

Tapo C400S2

User Guide

Smart Wire-Free Security Camera System

Contents

About This Guide ···········································································1

Introduction ······················································································ 2

Appearance-Camera ···································································3

Appearance-Hub ········································································4

Charge the Battery ········································································7

Set Up Your Camera ·····································································8

Install a microSD Card ······························································10

Installation Options ····································································11

Mount Your Camera··································································· 12

Authentication ··············································································13

About This Guide

This guide provides a brief introduction to the Smart Wire-Free Security Camera System and the Tapo app, as well as regulatory information.

Please note that features available in Tapo may vary by model and software version. Tapo availability may also vary by region. All images, steps, and

descriptions in this guide are only examples and may not reect your actual Tapo Camera experience.

Conventions

In this guide, the following convention is used:

Convention Description

Blue Key information appears in blue, including management page text such as menus, items, buttons and so on.

Underline Hyperlinks are in blue and underlined. You can click to redirect to a website.

Note: Ignoring this type of note might result in a malfunction or damage to the device.

More Info

• Specications can be found on the product page at https://www.tapo.com.

• Our Technical Support and troubleshooting information can be found at https://www.tapo.com/support/.

Introduction

Install anywhere with long battery life.

Tapo Wire-Free Security Camera System is designed to be used outdoors. Its rechargeable and removable battery with a low-power protocol extends

your usage. No wires means you can place the camera wherever you like.

• 1080p Full HD Live View – Check 24hrs clear live view through the Tapo app.

• 180 Day Long Battery Life* – The rechargeable and removable battery with a low-power protocol extends your usage.

*180-day battery life is based on TP-Link's laboratory testing with 10-20 triggered events per day. Actual battery life may vary based on device

settings, use, and environmental factors.

• Wire-Free Placement – No wires means you can place the cameras almost anywhere inside or outside - whatever works for you.

• Smart AI Detection – Detect multiple event types with smart AI algorithms. Adjust the sensitivity according to your needs.

• Sound Alarm – Trigger sound as an alarm when motion is detected.

• Motion Detection – Get instant notications when your camera detects motion.

• Weatherproof – Helps Tapo cameras perform well even in harsh environments with rain and dust.

• Two-Way Audio – Communicate with others with the built-in microphone and speaker.

• Activity Zone – Notify you when activity is detected in your specic zone.

• Flexible Storage Choices – Save recorded videos on the hub-installed microSD* card (up to 256 GB) or by using Tapo Care** cloud storage services.

*microSD card needs to be purchased separately.

**Subscribe for cloud storage at https://www.tapo.com/tapocare/.

Appearance-Camera

Front Back

Indicate the status of your camera. While the camera is powered on:

3Motion Sensor

4Status LED

2Light Sensor

Lens

5Microphone

SYNC/RESET Button

Press for 1 second: Pair with the hub

Press and hold for at least 5 seconds: Reset the camera

RES

SYNC

42 5

Appearance-Hub

▲

microSD card not included.

1SYNC

Press to pair with the camera, or silence the hub when it rings.

2RESET

Press and hold for at least 5 seconds until the hub LED quickly

blinks red to reset the hub.

3microSD Card Slot

Insert a microSD card to record camera videos locally.

Initialize the microSD card within the Tapo app rst.

4Status LED

Indicate the status of your hub.

microSD

1 2 3

Solid amber

Blinking red quickly

Solid red

Solid green

Blinking green quickly

Starting up

Connected to the cloud

Connected to router

Hub resetting

Hub updating

Blinking red and green Ready for setup

Blinking green slowly Pairing

Hub Status LED

Camera Status LED

Blinking red and green

Solid Red

Blinking red once a minute

Blinking green quickly Camera updating

Blinking red quickly Camera resetting

Ready for pairing

Pairing

Blinking red slowly

Blinking green slowly

Solid green Connected to the cloud

Solid amber Connected to the hub

Starting up

Low battery

Oine

Charge the Battery

Method 1:

Connect the battery to a power source.

Method 2:

Insert the battery into the camera, and then connect the camera to a power source.

Solid amber

Solid green

5V USB Charger

Charging:

Fully charged:

5V USB Charger

Set Up Your Camera

Follow the steps below to get started with your new hub and camera.

Step 1. Download Tapo App

Get the Tapo app from the App Store or

Google Play, or by scanning the QR code

below.

Step 2. Log In

Open the app, and log in with your TP-Link ID.

If you don't have an account, create one rst.

Step 3. Add Your Hub First

Tap the button in the app and select your

model. Follow app instructions to set up your

hub.

Step 4. Add Your Camera

Tap the button in the app and select your

model. Follow app instructions to set up your

camera.

Install a microSD Card

If you want the camera to record videos locally, insert a microSD card to your hub.

Initialize the microSD card within the Tapo app.

You can go to Camera Settings > microSD Card in the Tapo app to check the card status or format your card.

microSD

Installation Options

When you nish adding your camera in the Tapo app, you can place your camera on a at surface, or mount it on a wall or ceiling with the provided

mounting template and screws.

Option 1. Set on a Table Option 2. Mount to the Wall

Install

Rotate to secure

the bracket

Rotate after installing

Rotate to secure

the bracket

Rotate after installing

Install

Mount Your Camera

When you nish adding your camera in the Tapo app, you can place your camera on a at surface, or mount it on a wall or ceiling with the provided

mounting template and screws.

Step 1. Drill Holes

Stick the mounting template to the desired

mounting place. Drill 3 screw holes according

to the template.

Step 2. Install the Bracket

Insert three anchors into the holes and use the

screws to ax the bracket over the anchors.

Step 3. Mount Camera

Install the camera to the mounting bracket,

and adjust the camera angle.

Size of Screws

1.8±0.1

30±0.5

3.5±0.1

Authentication

FCC compliance information statement

Product Name: Smart Wire-Free Security Camera System

Model Number: Tapo C400S2

Component Name Model

I.T.E. Power Supply T090085-2B1

USB ADAPTER A8-501000

Rechargeable Lithium-ion Battery Tapo A100-INT

Responsible Party:

TP-Link USA Corporation

Address: 10 Mauchly, Irvine, CA 926181

Website: http://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6804

E-mail: [email protected]om

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications

could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be

co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this

transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction

with any other antenna or transmitter.”

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards,

FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2023-01-12

FCC compliance information statement

Product Name: I.T.E. Power Supply

Model Number: T090085-2B1

Product Name: USB ADAPTER

Model Number: A8-501000

Product Name: Rechargeable Lithium-ion Battery

Model Number: Tapo A100-INT

Responsible Party:

TP-Link USA Corporation

Address: 10 Mauchly, Irvine, CA 926181

Website: http://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6804

E-mail: [email protected]om

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards,

FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2023-01-12

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take

adequate measures.

OPERATING FREQUENCY (the maximum transmitted power)

2412MHz—2472MHz (20dBm)

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU,

2009/125/EC, 2011/65/EU and (EU)2015/863.

The original EU declaration of conformity may be found at https://www.tapo.com/en/support/ce/

RF Exposure Information

This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way

of health protection.

The device complies with RF specifications when the device used at 20 cm from your body.

UK Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment

Regulations 2017.

The original UK declaration of conformity may be found at https://www.tapo.com/support/ukca/

Canadian Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-

exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement

économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

1. l’appareil ne doit pas produire de brouillage;

2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator & your body.

Déclaration d’exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être

installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

Korea Warning Statements:

당해 무선설비는 운용중 전파혼신 가능성이 있음.