Behringer EUROCOM MA4000M Quick start guide

Behringer
Brand
Behringer
Model
EUROCOM MA4000M
Category
Soundbar speakers
Type
Quick start guide

This manual is also suitable for

Quick Start Guide (Check out behringer.com for FullManual)
EUROCOM
MA4008
Energy-Ecient, Multi-Function 80-Watt Mixing Amplier with
Dual70/100 V and4 Ω Outputs
MA4000M
Energy-Ecient, 9-Input Mixer Featuring Multiple Input Connectivity
and DiverseSignal Routing
LEGAL DISCLAIMER
LIMITED WARRANTY
Terminals marked with this
symbol carry electrical
current of su cient
magnitude to constitute risk of electric
shock. Use only high-quality professional
speaker cables with ¼" TS or twist-
locking plugs pre-installed. Allother
installation or modi cation should be
performed only by quali edpersonnel.
This symbol, wherever it
appears, alerts you to the
presence of uninsulated
dangerous voltage inside the enclosure
-voltage that may be su cient to
constitute a risk ofshock.
This symbol, wherever it
appears, alertsyou to
important operating and
maintenance instructions in the
accompanying literature. Please read
themanual.
Caution
To reduce the risk of electric
shock, do not remove the
top cover (or the rear section). No user
serviceable parts inside. Refer servicing
to quali edpersonnel.
Caution
To reduce the risk of  re or
electric shock, do not expose
this appliance to rain and moisture.
Theapparatus shall not be exposed to
dripping or splashing liquids and no
objects  lled with liquids, such as vases,
shall be placed on the apparatus.
Caution
These service instructions
are for use by quali ed
service personnel only. Toreduce the
risk of electric shock do not perform any
servicing other than that contained in the
operation instructions. Repairs have to be
performed by quali ed servicepersonnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus
nearwater.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, stoves,
orother apparatus (including ampli ers)
thatproduceheat.
9. Do not defeat the safety purpose
of the polarized or grounding-type plug.
Apolarized plug has two blades with
one wider than the other. A grounding-
type plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
Ifthe provided plug does not  t into
your outlet, consult an electrician for
replacement of the obsoleteoutlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
11. Use only attachments/accessories
speci ed by themanufacturer.
12. Use only with
the cart, stand,
tripod, bracket,
ortable speci ed by
the manufacturer,
orsold with
the apparatus. When a cart is used,
usecaution when moving the cart/
apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during
lightning storms or when unused for long
periods oftime.
14. Refer all servicing to quali ed
service personnel. Servicing is required
when the apparatus has been damaged
in any way, such as power supply cord or
plug is damaged, liquid has been spilled
or objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has beendropped.
15. The apparatus shall be connected to
a MAINS socket outlet with a protective
earthingconnection.
16. Where the MAINS plug or an
appliance coupler is used as the
disconnect device, thedisconnect device
shall remain readilyoperable.
TECHNICAL SPECIFICATIONS AND
APPEARANCES ARE SUBJECT TO CHANGE
WITHOUT NOTICE AND ACCURACY
IS NOT GUARANTEED. BEHRINGER,
KLARK TEKNIK, MIDAS, BUGERA,
AND TURBOSOUND ARE PART OF THE
MUSIC GROUP MUSICGROUP.COM.
ALLTRADEMARKS ARE THE PROPERTY
OF THEIR RESPECTIVE OWNERS.
MUSICGROUP ACCEPTS NO LIABILITY
FOR ANY LOSS WHICH MAY BE
SUFFERED BY ANY PERSON WHO RELIES
EITHER WHOLLY OR IN PART UPON
ANY DESCRIPTION, PHOTOGRAPH
OR STATEMENT CONTAINED HEREIN.
COLORSAND SPECIFICATIONS MAY
VARY FROM ACTUAL PRODUCT.
MUSIC GROUP PRODUCTS ARE
SOLD THROUGH AUTHORIZED
FULFILLERS AND RESELLERS ONLY.
FULFILLERSAND RESELLERS ARE
NOT AGENTS OF MUSICGROUP AND
HAVE ABSOLUTELY NO AUTHORITY
TO BIND MUSICGROUP BY ANY
EXPRESS OR IMPLIED UNDERTAKING
OR REPRESENTATION. THIS MANUAL
IS COPYRIGHTED. NO PART OF THIS
MANUAL MAY BE REPRODUCED OR
TRANSMITTED IN ANY FORM OR BY ANY
MEANS, ELECTRONICOR MECHANICAL,
INCLUDINGPHOTOCOPYING
AND RECORDING OF ANY KIND,
FORANY PURPOSE, WITHOUT THE
EXPRESS WRITTEN PERMISSION OF
MUSICGROUPIPLTD.
ALL RIGHTS RESERVED.
© 2013 MUSICGroupIPLtd.
Trident Chambers, Wickhams Cay,
P.O. Box 146, Road Town, Tortola,
BritishVirgin Islands
For the applicable warranty
terms and conditions and
additional information regarding
MUSICGroup’s Limited Warranty,
please see complete details online at
www.music-group.com/warranty.
Las terminales marcadas con
este símbolo transportan
corriente eléctrica de
magnitud su ciente como para constituir
un riesgo de descarga eléctrica.
Utilicesolo cables de altavoz
profesionales y de alta calidad con
conectores TS de 6,3 mm o de bayoneta
pre jados. Cualquier otra instalación o
modi cación debe ser realizada
únicamente por un técnicocuali cado.
Este símbolo, siempre que
aparece, leadvierte de la
presencia de voltaje
peligroso sin aislar dentro de la caja;
estevoltaje puede ser su ciente para
constituir un riesgo dedescarga.
Este símbolo, siempre que
aparece, leadvierte sobre
instrucciones operativas y
de mantenimiento que aparecen en la
documentación adjunta. Por favor,
leaelmanual.
Atención
Para reducir el riesgo de
descarga eléctrica, noquite
la tapa (olaparte posterior). No hay
piezas en el interior del equipo que
puedan ser reparadas por el usuario.
Sies necesario, póngase en contacto con
personal cuali cado.
Atención
Para reducir el riesgo
de incendio o descarga
eléctrica, no exponga este aparato a la
lluvia, humedad o alguna otra fuente que
pueda salpicar o derramar algún líquido
sobre el aparato. Nocoloque ningún
tipo de recipiente para líquidos sobre
elaparato.
Atención
Las instrucciones de servicio
deben llevarlas a cabo
exclusivamente personal cuali cado.
Paraevitar el riesgo de una descarga
eléctrica, no realice reparaciones que no
se encuentren descritas en el manual
de operaciones. Lasreparaciones deben
ser realizadas exclusivamente por
personalcuali cado.
1. Lea las instrucciones.
2. Conserve estas instrucciones.
3. Preste atención a todas
lasadvertencias.
4. Siga todas las instrucciones.
5. No use este aparato cerca del agua.
6. Limpie este aparato con un pañoseco.
7. No bloquee las aberturas de
ventilación. Instale el equipo de acuerdo
con las instrucciones del fabricante.
8. No instale este equipo cerca de
fuentes de calor tales como radiadores,
acumuladores de calor, estufas u otros
aparatos (incluyendo ampli cadores)
quepuedan producir calor.
9. No elimine o deshabilite nunca la
conexión a tierra del aparato o del cable
de alimentación de corriente. Unenchufe
polarizado tiene dos polos, uno de los
cuales tiene un contacto más ancho que
el otro. Una clavija con puesta a tierra
dispone de tres contactos: dos polos y
la puesta a tierra. El contacto ancho y el
tercer contacto, respectivamente, sonlos
que garantizan una mayor seguridad.
Siel enchufe suministrado con el equipo
no concuerda con la toma de corriente,
consulte con un electricista para cambiar
la toma de corriente obsoleta.
10. Coloque el cable de suministro de
energía de manera que no pueda ser
pisado y que esté protegido de objetos
a lados. Asegúrese de que el cable de
suministro de energía esté protegido,
especialmente en la zona de la clavija y en
el punto donde sale del aparato.
11. Use únicamente los dispositivos o
accesorios especi cados por el fabricante.
12. Use únicamente
la carretilla,
plataforma, trípode,
soporte o mesa
especi cados por el
fabricante o
suministrados junto con el equipo.
Altransportar el equipo, tengacuidado
para evitar daños y caídas al tropezar con
algúnobstáculo.
13. Desenchufe el equipo durante
tormentas o si no va a utilizarlo durante
un periodo largo.
14. Confíe las reparaciones únicamente
a servicios técnicos cuali cados.
Launidad requiere mantenimiento
siempre que haya sufrido algún daño,
si el cable de suministro de energía o el
enchufe presentaran daños, sehubiera
derramado un líquido o hubieran caído
objetos dentro del equipo, si el aparato
hubiera estado expuesto a la humedad
o la lluvia, si ha dejado de funcionar de
manera normal o si ha sufrido algún
golpe o caída.
15. Al conectar la unidad a la toma de
corriente eléctrica asegúrese de que la
conexión disponga de una unión atierra.
16. Si el enchufe o conector de red
sirve como único medio de desconexión,
éstedebe ser accesiblefácilmente.
LAS ESPECIFICACIONES TÉCNICAS
Y LA APARIENCIA EXTERIOR ESTÁN
SUJETAS A CAMBIOS SIN PREVIO AVISO
Y NO PODEMOS GARANTIZAR LA TOTAL
EXACTITUD DE TODO LO QUE APARECE
AQUÍ. BEHRINGER, KLARK TEKNIK,
MIDAS, BUGERA, YTURBOSOUND
SON PARTE DEL GRUPO MUSIC GROUP
MUSICGROUP.COM. TODAS LAS
MARCAS REGISTRADAS SON PROPIEDAD
DE SUS RESPECTIVOS DUEÑOS.
MUSICGROUP NO ACEPTA NINGÚN TIPO
DE RESPONSABILIDAD POR POSIBLES
Important Safety
Instructions
Instrucciones de
seguridad
NEGACIÓN LEGAL
2 3Quick Start GuideEUROCOM MA4008/MA4000M
Page is loading ...
Page is loading ...
(EN) Step 1: Hook-Up
(ES) Paso 1: Conexión
(FR) Étape 1 : Connexions
(DE) Schritt 1: Verkabelung
(PT) Passo 1: Conexões
EUROCOM MA4008/MA4000M Hook-up
MA4008 system setup
Configuración del sistema MA4008
Configuration du système MA4008
MA4008 Systemeinrichtung
Configuração do sistema do MA4008
MP3 PlayerRemote
AX6220
ST2400 ST2400
MA4008
CD Player
ST208S
CL106
TN6232
CL106
Tuner
HD Recorder
TEL / PAGE
8 EUROCOM MA4008/MA4000M 9 Quick Start Guide
(EN) Step 1: Hook-Up
(ES) Paso 1: Conexión
(FR) Étape 1 : Connexions
(DE) Schritt 1: Verkabelung
(PT) Passo 1: Conexões
EUROCOM MA4008/MA4000M Hook-up
AX6220
MA4000M
CD Player
CL106TCL106T
CL106
AX6240Z
CL106
Tuner
HD Recorder
TEL / PAGE
ST2400 ST2400 ST2400 ST2400
MP3 PlayerRemote
MA4000M system setup
Configuración del sistema MA4000M
Configuration du système MA4000M
MA4000M Systemeinrichtung
Configuração do sistema do MA4000M
10 EUROCOM MA4008/MA4000M 11 Quick Start Guide
(EN) Step 2: Controls
(ES) Paso 2: Controles
(FR) Étape 2 : Réglages
(DE) Schritt 2: Regler
(PT) Passo 2: Controles
EUROCOM MA4008/MA4000M Controls
POWER INDICATOR
glows amber when the
unit is powered on.
INDICADOR POWER
se ilumina en naranja
cuando la unidad
estáencendida.
LE TÉMOIN POWER
s'allume en jaune à la
mise sous tension.
NETZANZEIGE
leuchtet gelbbei
einge schal tetemGerät.
INDICADOR POWER
Ilumina-se com uma
cor âmbar quando a
unidade está ligada .
POWER switch turns
the uniton and o.
El interruptor POWER
le permite encender y
apagar la unidad.
L'INTERRUPTEUR
place l'appareil
sous/hors tension.
NETZSCHALTER
schaltet das
Gerätein/aus.
O botão POWER liga e
desliga a unidade.
INPUT LEVEL
CONTROLS 1 – 8
adjust the gain
of corresponding
microphone or line-
level input signals.
CONTROLES INPUT
LEVEL 1 – 8 le
permiten ajustar la
ganancia de las señales
de entrada de nivel
de línea o micrófono
correspondientes.
RÉGLAGES DE
NIVEAU D'ENTRÉE
1 – 8 déterminent
le gain des signaux
d'entrée micro ou
lignecorrespondants.
EINGANGSPEGEL-
REGLER 1 – 8 steuern
die Verstärkung der
entsprechenden
Eingangssignale
mit Mikrofon- oder
Line-Pegel.
CONTROLES (DE
NÍVEL DE ENTRADA)
INPUT LEVEL 1 – 8
ajustam o ganho
do microfone
correspondente ou de
sinais de entrada de
nível de linha.
LO EQ CONTROL
adjusts the
low frequency
(bass)response.
CONTROL EQ LO le
permite ajustar la
respuesta de bajas
frecuencias (graves).
Le RÉGLAGE LO
EQ modie la
réponse dans les
bassesfréquences.
LO EQ-REGLER
steuert den
Bassfrequenzgang.
CONTROLE LO EQ
ajusta a resposta
de frequências
baixas(bass).
HI EQ CONTROL
adjusts the
high frequency
(treble)response.
CONTROL EQ HI le
permite ajustar la
respuesta de altas
frecuencias (agudos).
Le RÉGLAGEHIEQ
modie la
réponse dans les
hautesfréquences.
HI EQ-REGLER
steuert den
Höhenfrequenzgang.
CONTROLE HI EQ
ajusta a resposta
das frequências
altas(treble).
VU METER indicates
the signal level of
theampliers.
VUMETRO indica
el nivel de señal de
losamplicadores.
Le VU-MÈTRE indique
le niveau du signal
desamplicateurs.
VU METER zeigt
den Signalpegel der
Verstärker an.
MEDIDOR VU indica
o nível do sinal
dosamplicadores.
DUAL-FUNCTION
INDICATOR RING
glows yellow when
power is on, turns red
at onsetofclipping.
ANILLO INDICADOR
DE DOBLE FUNCIÓN
se ilumina en amarillo
cuando la unidad esté
encendido y en rojo
en cuanto se produzca
una saturación
(sobrecarga).
La BAGUE
LUMINEUSE À
DOUBLE FONCTION
s'allume en jaune pour
indiquer la mise sous
tension, ets'allume
en rouge pour
indiquerl'écrêtage.
DOPPELFUNKTIONS-
ANZEIGERING
leuchtet gelb bei
eingeschaltetem
Gerät und rot bei
bevorstehendem
Clipping.
ANEL INDICADOR
DEFUNÇÃO DUPLA
brilha com uma cor
amarela quando a
unidade está ligada,
ca vermelho na
presença de clipping.
MASTER VOLUME
adjusts the overall
volume level.
MASTER VOLUME
ajusta el nivel de
volumen global.
Le MASTER VOLUME
détermine le niveau de
sortie général.
MASTER VOLUME
regelt die
Gesamt lautstärke.
MASTER VOLUME
ajusta o nível do
volume geral.
12 EUROCOM MA4008/MA4000M 13 Quick Start Guide
(EN) Step 2: Controls
(ES) Paso 2: Controles
(FR) Étape 2 : Réglages
(DE) Schritt 2: Regler
(PT) Passo 2: Controles
EUROCOM MA4008/MA4000M Controls
POWER SOURCE jack
accepts the included
IEC power cable.
Conecte en la clavija
POWER SOURCE el
cable de alimentación
IEC incluido.
L'embase POWER
SOURCE accepte
le cordon secteur
IECfourni.
NETZANSCHLUSS
für das mitgelieferte
IEC-Netzkabel.
O jack POWER
SOURCE aceita o
cabo de alimentação
IECincluso.
AMPLIFIER OUTPUTS
(MA4008 only) 4-pin
Euroblock connector
accepts the included
mating connector for
connection to high
and low impedance
loudspeakers.
AMPLIFIER OUTPUTS
(solo MA4008)
Euroconector de 4
puntas que acepta la
clavija incluida para
la conexión a recintos
acústicos de alta y
bajaimpedancia.
AMPLIFIER
OUTPUTS (MA4008
uniquement).
Cesconnecteurs
Euroblock à 4
broches acceptent
les ches fournies
correspondantes
pour la connexion des
haut-parleurs haute et
basse impédance.
AMPLIFIER OUTPUTS
(nur MA4008) Dieser
4-Pol Euroblock-
Anschluss akzeptiert
das mitgelieferte
Gegenstück zum
Anschließen von
hoch- und niederohmigen
Lautsprechern.
As saídas dos
amplicadores
AMPLIFIER OUTPUTS
(somenteMA4008)
conector Eurobolock
de 4 pinos aceita
o conector
correspondente
incluso para
conexão com alto-
falantes de alta e
baixaimpedância.
HI-Z MODE switch
selects between
70or 100 V operation
for the high
impedanceamplier.
El interruptor HI-Z
MODE le permite
elegir entre el
funcionamiento
a 70ó 100 V para
el amplicador de
altaimpedancia.
Le sélecteur HI-Z
MODE sélectionne
le mode de sortie
à 70ou 100 V de
l'amplicateur
hauteimpédance.
HI-Z MODE-Schalter
wählt zwischen dem
70und 100 V-Betrieb
für den hochohmigen
Verstärker.
O botão HI-Z MODE
possibilita a seleção
entre operações de
70 ou 100 V para
o amplicador de
altaimpedância.
MUTE depth control
adjusts the volume
level of background
music during a
mute event, e.g.,
apageannouncement.
El control MUTE DEPTH
ajusta el nivel de
volumen que tendrá la
música de fondo en los
eventos de anulación
de señal, p.e. un aviso
pormegafonía.
Le réglage MUTE
détermine le niveau
de la musique en
arrière plan lors d'une
coupure, comme une
annonce, par exemple.
MUTE DEPTH-Regler
steuert die Lautstärke
der Hintergrundmusik
während eines
Mute Events,
z.B.einerDurchsage.
O controle MUTE
Depth ajusta o nível
do volume da música
de fundo enquanto
o modo mute está
ativo, ex: anúncios no
alto-falante.
MIC / LINE INPUTS
3–8 accept balanced
or unbalanced,
microphone or
line-level signals
via 3-pin Euroblock
connectors.
Las tomas de entrada
MIC / LINE INPUTS
3–8 aceptan
señales de nivel de
micrófono o de línea,
balanceadas o no
balanceadas, a través
de Euroconectores
de3 puntas.
Les ENTRÉES MIC /
LINE 3–8 acceptent
des signaux micro ou
ligne, symétriques
ou asymétriques sur
connecteur Euroblock
à 3 broches.
MIC / LINE INPUTS
3–8 Diese 3-Pol
Euroblock-Anschlüsse
akzeptieren
symmetrische oder
unsymmetrische
Signale mit Mikrofon-
oder Line-Pegel.
As entradas MIC/
LINE INPUTS 3-8
aceitam sinais de
nível de microfone
ou de linha
balanceados ou não
balanceados através
dos conectores
Euroblockde 3 pinos.
MIC / LINE INPUTS
1– 4 accept balanced
or unbalanced,
microphone or line-
level signals via XLR/
TRS combinationjacks.
Las tomas de entrada
MIC / LINE INPUTS
1– 4 aceptan señales
de nivel de micrófono
o de línea, balanceadas
o no balanceadas, a
través de tomas combo
XLR/TRS.
Les ENTRÉES MIC /
LINE 1– 4 acceptent
des signaux à
niveau micro ou
ligne, symétriques
ou asymétriques
sur embases
combinées XLR/Jacks
6,35mmstéréo .
MIC / LINE INPUTS
1– 4 Diese XLR/
TRS-Kombibuchsen
akzeptieren
symmetrische oder
unsymmetrische
Signale mitMikrofon-
oderLine-Pegel.
As entradas MIC /
LINE INPUTS 1– 4
aceitam microfones ou
sinais de nível de linha
balanceados ou não
balanceados através
do conjunto de jacks
XLR/TRS.
AUX INPUTS 5 – 8
accept line-level
signals into RCAjacks
and are summed
tomono.
Las tomas de entrada
AUX INPUTS 5 – 8
aceptan señales de
nivel de línea a través
de clavijas RCA y son
sumadas en mono.
Les entrées AUX
INPUTS 5 – 8
acceptent des signaux
ligne sur ces embases
RCAmélangées
enmono.
AUX INPUTS 5 – 8
Diese Cinch-Buchsen
akzeptieren
Line-Pegel-Signale,
dieauf Mono
summiertwerden.
As entradas AUX
INPUTS 5 – 8 aceitam
sinais de nível de linha
em jacks RCA e são
colocadas em mono.
AC VOLTAGE switch
selects between
115VAC and240VAC.
El interruptor AC
VOLTAGE le permite
elegir el voltaje de
alimentación entre
115y240V CA.
Le sélecteur AC
VOLTAGE sélectionne
une tension secteur de
115Vca ou de 240Vca.
SPANNUNGSWAHL-
SCHALTER wählt
zwischen 115VAC
und240VAC.
O botão de VOLTAGEM
AC seleciona entre 115
VAC e 240 VAC
BALANCE
(MA4008only)
controlvaries drive
level between
LO-Z and HI-Z
powerampliers.
El control BALANCE
(solo MA4008)
cambiael nivel de
saturación entre las
etapas de potencia
LO-Z y HI-Z.
Le réglage BALANCE
(MA4008uniquement)
dose le niveau du
signal appliqué aux
amplicateurs LO-Z
et HI-Z.
BALANCE-Regler
(nurMA4008)
variiert den
Ansteuerungspegel
zwischen den nieder-
und hochohmigen
Endstufen
(LO-ZundHI-Z).
O controle BALANCE
(somente MA4008)
varia o nível de
saturação entre os
amplicadores de
potência LO-Z e HI-Z.
14 EUROCOM MA4008/MA4000M 15 Quick Start Guide
(EN) Step 2: Controls
(ES) Paso 2: Controles
(FR) Étape 2 : Réglages
(DE) Schritt 2: Regler
(PT) Passo 2: Controles
EUROCOM MA4008/MA4000M Controls
FUNCTION switches
assign INPUTS
5 – 8 to MAIN output,
PREOUT/AMP IN
links, PAGEphantom
power, and PAGE MIC/
LINEselect.
Los interruptores
FUNCTION asignan
las entradas INPUTS
5 – 8 a la salida MAIN,
enlaces PREOUT/
AMP IN, activan la
alimentación fantasma
PAGE y eligen
PAGEMIC/LINE.
Les micro-contacteurs
FUNCTION aectent
les entrées INPUTS
5 – 8 à la sortie MAIN,
couplent la sortie
PREOUT à l'entrée
AMP IN links, activent
l'alimentation
fantôme PAGE,
et sélectionnent
PAGEMIC ou LINE.
FUNKTIONS-Schalter
zur Zuweisung der
INPUTS 5 – 8 zum
MAIN-Ausgang,
zu PREOUT/AMP
IN-Verbindungen,
zur PAGE-
Phantomspannung
und zur PAGE
MIC/LINE-Wahl.
Os botões FUNCTION
ativam as entradas
INPUT 5-8 à saída
MAIN, links PRE OUT/
AMP IN, alimentação
fantasma PAGE e
PAGEMIC/LINE select.
MOH level control
adjusts the Z2/MOH
(Music On Hold)
outputlevel.
El control de nivel
MOH ajusta el nivel
de la salida Z2/MOH
(música durante
laespera).
Le réglage MOH
détermine le niveau
de la sortie Z2/MOH
(Music On Hold).
MOH-Pegelregler
steuert den
Ausgangspegel am
Z2/MOH-Anschluss
(Warteschleife).
O controle de nível
MOH ajusta o nível
da saída Z2/MOH
(músicadurante
tempo de espera).
RECORD output
provides a pre-master
line-level output split
to two RCA connectors.
La salida RECORD le
ofrece una señal de
nivel de línea pre-
master dividida en dos
clavijas RCA.
La sortie RECORD ore
un signal pré-Master à
niveau ligne, splité sur
deux RCA.
RECORD-Ausgang
liefert ein auf zwei
Cinch-Anschlüsse
verteiltes pre-master
Ausgangssignal mit
Line-Pegel.
A saída RECORD
possui sinal de nível
de linha pré-master
dividida em dois
conectoresRCA.
TEL/PAGE input
allows connection
to a telephone
paging system via
detachable 4-pin
Euroblockconnector.
La entrada TEL/PAGE
permite la conexión
a un sistema de
avisos telefónicos
(centralita) a través de
un Euroconector de 4
puntas extraíble.
L'entrée TEL/PAGE
permet la connexion
d'un système
d'appel (Paging)
par téléphone,
grâce à l'embase
Euroblockdétachable
à 4 broches.
TEL/PAGE-Eingang
kann über einen
abnehmbaren 4-Pol
Euroblock-Anschluss
mit einem Telefon-
Pagingsystem
verbunden werden.
A entrada TEL/PAGE
possibilita conexão
com um sistema
de aviso telefônico
através de um
conector Euroblock
de4 pinos.
Z2/MOH switches
assignINPUTS 1 – 8 to
Z2/MOHoutput.
Los interruptores
Z2/MOH asignan las
entradas INPUTS 1 – 8
a la salida Z2/MOH.
Les micro-contacteurs
Z2/MOH aectent les
entrées INPUTS 1 – 8 à
la sortie Z2/MOH.
Z2/MOH-Schalter
zur Zuweisung der
INPUTS 1 – 8 zum
Z2/MOH-Ausgang.
Os botões Z2/
MOH ativam as
entradas INPUT 1-8 à
saídaZ2/MOH.
Z2/MOH line-level
audio output allows
connectivity to
external equipment
dedicated to a second
listening zone or a
MOH (Music on Hold)
connection to a
telephone system.
La salida audio de
nivel de línea Z2/MOH
permite conectar esta
unidad a un dispositivo
externo dedicado a
una segunda zona
de escucha o a una
conexión MOH
(músicadurante
la espera) para
una centralita
deteléfonos.
La sortie audio à niveau
ligne Z2/MOH permet
la connexion d'un
équipement externe
dédié à une deuxième
zone d'écoute ou
pour une connexion
de mise en attente
de la musique MOH
(Music on Hold) à un
systèmetéléphonique.
Z2/MOH Dieser Line-
Pegel Audioausgang
kann mit externen
Geräten verbunden
werden, die einer
zweiten Hörzone oder
einem MOH-Anschluss
(Warteschleife)
eines Telefonsystems
zugewiesen sind.
PRE OUT/AMP IN
(MA4008 only) RCA
phono jacks are
provided for LO-Z
and HI-Z ampliers.
Use these to insert
an external signal
processor, such as
compressor/limiter
between preamp and
power amplier.
Los amplicadores
LO-Z y HI-Z disponen de
clavijas RCA PRE OUT/
AMP IN (solo MA4008).
Úselas para insertar un
procesador de señal
exterior, comoun
compresor/limitador
entre el previo y la
etapa de potencia.
Les RCA PRE OUT/
AMP IN (MA4008
uniquement) servent
aux amplicateurs
LO-Z et HI-Z . Utilisez-
les pour insérer un
processeur de signal
externe, comme un
compresseur/limiteur
entre le préampli
etl'amplicateur.
PRE OUT/AMP IN
(nur MA4008) Diese
Cinch-Buchsen stehen
für die nieder- und
hochohmigen
Verstärker (LO-Z und
HI-Z) zurVerfügung.
Übersie kann
man externe
Signalprozessoren,
wie Kompressor/
Limiter zwischen
Vorverstärker und
Endstufe einschleifen.
Os amplicadores LQ-Z
e HI-Z dispõem de
jacks RCA phone PRE
OUT/AMP IN (somente
MA4008). Use-os para
inserir um processador
de sinais externos,
tal como compressor/
limitador entre o
pré-amplicador
e o amplicador
depotência
A saída de áudio de
nível de linha Z2/MOH
possibilita conexão
com aparelhagem
externa dedicada
a uma segunda
zona de áudio ou
a uma conexão
MOH (músicaem
espera) para um
sistematelefônico.
16 EUROCOM MA4008/MA4000M 17 Quick Start Guide
(EN) Step 2: Controls
(ES) Paso 2: Controles
(FR) Étape 2 : Réglages
(DE) Schritt 2: Regler
(PT) Passo 2: Controles
EUROCOM MA4008/MA4000M Controls
PAGE level control
adjusts the PAGE
inputlevel.
El control de nivel
PAGE ajusta el nivel de
la entrada PAGE.
Le réglage PAGE
détermine le niveau
d'entrée PAGE.
PAGE-Pegelregler
steuert den PAGE-
Eingangspegel.
O controle de nível
PAGE ajusta o nível da
entrada PAGE.
SIG LED glows GREEN
when the input level is
nominal for the input.
El piloto SIG se ilumina
en VERDE cuando el
nivel es nominal para
la entrada.
La Led SIG s'allume en
VERT lorsque le niveau
d'entrée et nominal.
SIG LED leuchtet
GRÜN, wenn der
Eingangspegel dem
Nominalwert des
Eingangs entspricht.
O LED SIG ilumina-
se com uma luz
VERDE quando o
nível é nominal
paraaentrada
GAIN controls are
provided on each
input channel
to optimize
preampgain.
Dispone de controles
GAIN en cada
canal de entrada
para optimizar la
ganancia del previo.
Le réglage de GAIN
de chaque entrée
optimise le niveau
du signal en entrée
dela voie.
GAIN-Regler zur
Optimierung der
Vorverstärkung sind
pro Eingangskanal
verfügbar.
Controles GAIN são
fornecidos em cada
canal de entrada
para otimizar o
ganho do pré-
amplicador.
MIC/LINE/PHTM
switch selects
between microphone-
level, line-level, or
microphone-level with
phantompower.
El interruptor MIC/
LINE/PHTM le permite
elegir entre nivel de
micrófono, nivel de
línea o nivel de micro
con alimentación
fantasma.
Le sélecteur MIC/
LINE/PHTM
sélectionne le
signal micro, ligne,
ou micro avec
alimentationfantôme.
MIC/LINE/
PHTM-Schalter
wählt zwischen
Mikrofonpegel,
Line-Pegel oder
Mikrofonpegel mit
Phantomspannung.
O botão MIC/LINE/
PHTM possibilita a
seleção entre o nível
do microfone, nível
de linha, ou nível
de microfone com
alimentação fantasma.
MIC/LINE INPUTS 1
and 2 accept balanced
or unbalanced,
microphone or line-
level signals via 4-pin
Euroblock connectors.
A MUTE terminal is
provided to toggle the
muting function.
Las entradas MIC/
LINE INPUTS 1 y 2
aceptan señales de
nivel de micro o línea,
balanceadas o no
balanceadas, a través
de Euroconectores de
4 puntas. Dispone de
un terminal MUTE para
conmutar la función de
anulación (mute).
Les ENTRÉES
MIC/LINE 1 et 2
acceptent les signaux
symétriques ou
asymétriques, à niveau
micro ou ligne par le
connecteur Euroblock
à 4 broches. Une borne
MUTE active/désactive
la coupure du signal.
MIC/LINE INPUTS
1 und 2 Diese 4-Pol
Euroblock-Anschlüsse
akzeptieren
symmetrische oder
unsymmetrische
Signale mit Mikrofon-
oder Line-Pegel. Der
verfügbare MUTE-
Anschlusspol dient
zum Umschalten der
Mute-Funktion.
As entradas MIC/LINE
INPUTS 1 e 2 aceitam
sinais de nível de
microfone balanceados
ou não balanceados,
através de conectores
Euroblock de 4 pinos.
Um terminal MUTE
está disponível para
comutar a função do
modo mute.
REMOTE control
connector provides
terminals for Common,
+ 5 VDC, Remote
Volume, Mute, and
Power Toggle. Use this
5-pin Euroblock to
connect to an optional
remote control.
El conector de control
REMOTE dispone
de terminales para
Común, + 5 V DC,
volumen remoto,
mute y encendido.
Use este Euroconector
de 5 puntas para la
conexión de un control
remoto opcional.
L'embase REMOTE
possède des broches
de masse, + 5 Vcc,
télécommande
volume, Mute,
et Power On/O.
Utilisez cette embase
Euroblock à 5 broches
pour connecter
une télécommande
optionnelle.
REMOTE-Anschluss
mit Polen für
Common, + 5 VDC,
RemoteVolume,
Muteund Power
Toggle. Verbinden Sie
diesen 5-Pol Euroblock
mit einer optionalen
Fernbedienung.
O conector de
controle REMOTE
oferece terminais
para Common
(comum), +5V DC,
Remote Volume
(volumeremoto),
mute e Power Toggle.
Use o Euroblock de
5 pinos para fazer a
conexão a um controle
remotoopcional.
MA4000M
MAIN MIX
OUTPUT 1– 2
allows connection
to balanced or
unbalanced, MIC or
LINE-level inputs
via 3-pin Euroblock
connectors.
La salida MAIN MIX
OUTPUT 1– 2 permite
la conexión a entradas
de nivel de micro o
línea, balanceadas
o no balanceadas,
por medio de
Euroconectores
de3puntas.
Les sorties MAIN
MIX OUTPUT 1– 2
permettent une
connexion symétrique
ou asymétrique à des
entrées à niveau micro
ou ligne, grâce au
connecteur Euroblock
à 3broches.
MAIN MIX OUTPUT
1– 2 Diese 3-Pol
Euroblock-Anschlüsse
kann man mit
symmetrischen oder
unsymmetrischen
Eingängen mit
Mikrofon- oder Line-
Pegel verbinden.
A saída MAIN MIX
OUTPUT 1– 2
possibilita conexão à
entradas de nível de
microfone ou de linha
(MIC ou LINE-level)
através de conectores
Euroblock de 3 pinos.
18 EUROCOM MA4008/MA4000M 19 Quick Start Guide
(EN) Step 3: Getting
started
EUROCOM MA4008/MA4000M Getting started
Connections
MA4008 / MA4000M
Before terminating any wire,
turnallequipment o and
disconnect theAC power.
Make all appropriate audio and
power connections to the
MA4008 / MA4000M.
Set the input sensitivity
switches for the MIC/LINE inputs
to the appropriate position.
Select LINE for line-level signals, MIC for
mic-level signals, or PHTM when using
microphones that require phantom power.
MA4008 Amplier Connections
Ensure the FUNCTION switches 3
and 4 are set to the ON position
when not using the PRE OUT /
AMP IN loop.
Ensure the loudspeaker power
requirement does not exceed
the HI-Z amp’s available power
output. Add up the total transformer taps of
all the loudspeakers to be powered,
e.g.,four70 V loudspeakers using 10 W
transformer taps require 40 W of power.
Donot exceed 80W for the MA4008.
Set the HI-Z MODE switch to
either 70 or 100 V to match the
system’s loudspeaker
voltagerequirement.
Ensure the loudspeaker
impedance does not exceed
(notless than) the minimum
load impedance of MA4008’s LO-Z amplier
(4 Ω). For example, two 8 Ω loudspeakers
connectedin parallel equal a combined
impedanceof4Ω.
MA4000M MAIN OUTPUT Settings
Set DIP switches 1-4 (MAIN OUTPUT 1) or 1-3
(MAINOUTPUT 2) to MIC or LINE level.
Inserting external processing
(MA4008only)
DIP switches 1-3 and 1-4 break the
normally connected signal chain between
the preamp and power ampliers. Use
this function to connect external signal
processing equipment using the PREOUT
andAMPINconnections.
Set DIP switch 1-4 to the o
position to insert external
equipment to the LO-Zamplier
(use switch 1-3 for the HI-Zamplier).
Connect the appropriate channel
PRE OUT jack to the processor’s
line-level inputconnector.
Connect the processor’s output
to the appropriate channel
AMPINconnector.
Volume and Gain
Before powering up, set INPUT
LEVEL CONTROLS 1 – 8,
rearpanel GAIN controls 1 – 8,
and MASTER VOLUME to the full
counterclockwise (o)position.
Power on the unit
Slowly raise the rear panel
GAINcontrol for the individual
input channels until the green
SIG LED illuminates.
Equalizer
MA4008
Raise the MASTER VOLUME
control to the 10 – 12
o'clockposition.
Slowly raise the front panel
INPUT LEVELCONTROLS for the
individual inputchannels.
Adjust the MASTER VOLUME to
the desired overall
listeningvolume.
Adjust the LO and HI
equalization controls to tailor
system bass and
trebleresponse.
For the MA4008, adjust the
BALANCE control to set the
relative volume level between
the 70 / 100 V loudspeakers and the
4–16Ωloudspeakers.
Basic background music / paging
system setup
The basic muting function lowers the
volume level of background audio by a
designated amount when the unit receives
a contact-activated mute signal.
Contact-Activated Muting
Shorting pins 1 and 4 of any one of the MIC/
LINE or TEL/PAGE 4-pin Euroblock
connectors activates the muting function.
These terminals can be used for connection
to a dedicated mute switch or contact
closure from external equipment.
Turn the MUTE depth control to the
full clockwise position for maximum
attenuation. To defeat the mute
function (0 dB attenuation), turnthe
MUTE DEPTH control to the full
counterclockwiseposition.
Set the 3-position slide switch
on INPUT 1 to MIC (center).
Connect a dynamic microphone
to MIC/LINE INPUT 1.
Wire a N/O (normally-open)
momentaryswitch to pins 1
and 4 of the 4-pin Euroblock
connector on INPUT 1.
Set the 3-position slide switch
on INPUT 5 to LINE (right).
Connect a line-level music
source to AUXINPUT 5.
Set the MUTE DEPTH control to
thefullcounterclockwise
position (noattenuation).
Adjust the background music to
the desired listening level using
the volumecontrol for
AUXINPUT 4 on thefront panel.
While speaking into the
microphone and activating the
attached MUTE switch,
adjustthe volume control for MIC INPUT 1
on the front panel and the MUTE DEPTH
control on the rear panel so the
announcement is clearly audible over the
background music.
REMOTE Wiring Detail
A standard 10K Ω linear taper
potentiometer can be connected for remote
volume control.
Momentary switches can be used to
remotely-control system mute and
powertoggle.
GND + - MUTE
1 2 3 4
MUTE PWR
COM VDC RVC
N/C
10K Ω
20 EUROCOM MA4008/MA4000M 21 Quick Start Guide
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
(EN) Step 3: Getting
started
(ES) Paso 3: Puesta en
marcha
(FR) Étape 3 : Mise en
œuvre
(DE) Schritt 3: Erste
Schritte
(PT) Passo 3: Primeiros
Passos
EUROCOM MA4008/MA4000M Getting started
Switch Channel Function
2-8 INPUT 8 Assign to ZONE 2/MOH
2-7 INPUT 7 Assign to ZONE 2/MOH
2-6 INPUT 6 Assign to ZONE 2/MOH
2-5 INPUT 5 Assign to ZONE 2/MOH
2-4 INPUT 4 Assign to ZONE 2/MOH
2-3 INPUT 3 Assign to ZONE 2/MOH
2-2 INPUT 2 Assign to ZONE 2/MOH
2-1 INPUT 1 Assign to ZONE 2/MOH
Switch Channel Function
1-8 INPUT 8 Assign to MAIN ZONE
1-7 INPUT 7 Assign to MAIN ZONE
1-6 INPUT 6 Assign to MAIN ZONE
1-5 INPUT 5 Assign to MAIN ZONE
1-4
LINK LO-Z
AMP
Link PRE OUT to
LO-Z AMP IN
1-3
LINK HI-Z
AMP
Link PRE OUT to
HI-Z AMP IN
1-2 PAGE IN Assign Phantom Power
1-1 PAGE IN Assign Mic or Line-level
Switch Channel Function
2-8 INPUT 8 Assign to ZONE 2/MOH
2-7 INPUT 7 Assign to ZONE 2/MOH
2-6 INPUT 6 Assign to ZONE 2/MOH
2-5 INPUT 5 Assign to ZONE 2/MOH
2-4 INPUT 4 Assign to ZONE 2/MOH
2-3 INPUT 3 Assign to ZONE 2/MOH
2-2 INPUT 2 Assign to ZONE 2/MOH
2-1 INPUT 1 Assign to ZONE 2/MOH
Switch Channel Function
1-8 INPUT 8 Assign to MAIN ZONE
1-7 INPUT 7 Assign to MAIN ZONE
1-6 INPUT 6 Assign to MAIN ZONE
1-5 INPUT 5 Assign to MAIN ZONE
1-4
MAIN MIX
OUTPUT 1
Assign Mic or Line-level
1-3
MAIN MIX
OUTPUT 2
Assign Mic or Line-level
1-2 PAGE IN Assign Phantom Power
1-1 PAGE IN Assign Mic or Line-level
Conguration Switches / Interruptores
de conguración / Micro-contacteurs de
conguration / Kongurationsschalter /
Botões de conguração
MA4000M
MA4008
Connectors
Balanced ¼" TRS Connector
Unbalanced ¼" TS Connector
Balanced XLR Connectors
3-Pin Euroblock Connector - Input / Output
4-Pin Euroblock Connector - Input
4-Pole Euroblock Connector - Output
5-Pin Euroblock Connector - Remote
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
ring
cold (-)
tip
hot (+)
strain relief clamp
sleeve
tip
sleeve
ground/shield
tip
signal
1 = ground/shield
2 = hot (+)
3 = cold (-)
input
12
3
output
1
2
3
1
2
3
1. ground/shield
2. hot (+)
3. cold (-)
1
2
3
4
1. ground/shield
2. hot (+)
3. cold (-)
4. mute
1
2
3
4
1. LO-Z common
2. LO-Z (+)
3. HI-Z common
4. HI-Z (+)
1. common
2. +5 VDC
3. remote volume control
4. mute
5. power
1
2
3
4
5
30 EUROCOM MA4008/MA4000M 31 Quick Start Guide
Specications
MA4008 MA4000M
Audio Inputs
Mic / Line Inputs 1 & 2
Type
2 x XLR / ¼" TRS combo jacks
2 x 4-pin Euroblock in parallel
Impedance
Mic: -50 to 0 dBV, 600 Ω
Line: -27 to 0 dBV, 600 Ω
Electronically balanced
Mic / Line Inputs 3 & 4
Type
2 x XLR / ¼" TRS combo jacks
2 x 3-pin Euroblock in parallel
Impedance
Mic: -50 to 0 dBV, 600 Ω
Line: -27 to 0 dBV, 600 Ω
Electronically balanced
Inputs 5 - 8
Type 4 x 3-pin Euroblock, electronically balanced
Impedance
Mic: -50 to 0 dBV, 600 Ω
Line: -27 to 0 dBV, 600 Ω
Auxiliary
Type 4 x RCA stereo summed
Impedance -10 dBV, 10 kΩ, unbalanced Line: -10 dBV, 10 kΩ, unbalanced
Tel / Page input 1 x 4-pin Euroblock
Impedance
Mic: -50 to 0 dBV, 600 Ω
Line: -27 to 0 dBV, 600 Ω
Power amp input 1 x dual RCA jack —
Impedance 0 dBV, 600 Ω, unbalanced —
Phantom power
24 VDC, switchable
Inputs 1– 8 and Tel/Page
Audio Outputs
Amplier output 1 x 4-pin female Euroblock —
LO-Z 2 terminals @ 4 Ω —
HI-Z 2 terminals @ 70 V / 100 V, switchable —
Output regulation < 2 dB, no load to full load —
Main mix outputs 1 & 2 — 2 x 3-pin male Euroblock, Mic/Line switchable
Impedance —
Mic: -40 dBV, 1 kΩ
Line: 0 dBV, 600 Ω
Electronically balanced
Preamp output 1 x dual RCA jack —
Impedance 0 dBV, 600 Ω, unbalanced —
Z2 / Mon output 1 x dual RCA jack
Impedance 0 dBV, 600 Ω, unbalanced
Record output 1 x dual RCA jack
Impedance 0 dBV, 600 Ω, unbalanced
Amplier
Amplier channels
LO-Z: 1 x 4 Ω, minimum
HI-Z: 1 x 70 / 100 V, switchable
—
Power output LO-Z 1% THD,
1 kHz sine wave
80 W RMS @ 8 Ω
160 W RMS @ 4 Ω
—
Min. impedance 4 Ω —
Power output HI-Z 1% THD,
1 kHz sine wave
80 W RMS @ 70 V
80 W RMS @ 100V
—
Min. impedance
62 Ω @ 70 V
125 Ω @ 100 V
—
MA4008 MA4000M
System Information
Dynamic range
Mic: 65 dB
Line: 80 dB
THD+N 0.5% @ 1 kHz, rated output
Frequency response 50 Hz - 18 kHz, +/- 2 dB
Tone controls
Low: +/- 12 dB @ 100 Hz
High: +/- 12 dB @ 10 kHz
Control Connections
Remote 1 x 5-pin Euroblock connector
Volume 10 kΩ linear-taper potentiometer
Power +5 VDC voltage make contact input; no open voltage
Mute
No-voltage make contact input; open voltage 5 VDC
Short circuit: < 10 mA
DC power
+5 VDC, 100 mA
Current limited, short-circuit protected
Tel / Page 1 x 4-pin Euroblock, 1 terminal
Mute
No-voltage make contact input; open voltage 24 VDC
Short circuit: < 10 mA
Inputs 1 & 2 2 x 4-pin Euroblock, 1 terminal each
Mute
No-voltage make contact input; open voltage 24 VDC
Short circuit: < 10 mA
Indicators
Power LED ring illumination (Yellow)
Overload / protection LED ring indication (Red)
Output level LED VU output meter (Yellow and Red while clipping)
Power Supply (Fuses)
Mains voltage Switchable, 100 ~ 120/220 ~ 240 VAC, 50/60 Hz 100 ~ 240 VAC, 50/60 Hz
Fuse T 5 AH 250 V / T 2.5 AH 250V T 1 AH 250 V
Power eciency 68% (max.) —
Power consumption
52 W @ idle
70 W @ ⁄ power
113 W @ ⁄ power
234 W @ full power
26 W
Mains connector Standard IEC receptacle
Dimensions / Weight
Dimensions (H x W x D)
appr. 3.5 x 17 x 16"
appr. 88 x 432 x 406 mm
Weight appr. 13.4 lbs / 6.1 kg appr. 10.2 lbs / 4.6 kg
32 33Quick Start GuideEUROCOM MA4008/MA4000M
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Other important information
1. Register online. Pleaseregister
your new MUSICGroup equipment
right after you purchase it by visiting
behringer. com. Registeringyour purchase
using our simple online form helps us to
process your repair claims more quickly
and eciently. Also, read the terms and
conditions of our warranty, ifapplicable.
2. Malfunction. Should your
MUSICGroup Authorized Reseller not be
located in your vicinity, you may contact
the MUSIC Group Authorized Fulller for
your country listed under “Support” at
behringer. com. Shouldyour country not be
listed, pleasecheck if your problem can be
dealt with by our “OnlineSupport” which
may also be found under “Support” at
behringer. com. Alternatively, please submit
an online warranty claim at behringer. com
BEFORE returning theproduct.
3. Power Connections.
Beforeplugging the unit into a power
socket, please make sure you are using the
correct mains voltage for your particular
model. Faulty fuses must be replaced
with fuses of the same type and rating
withoutexception.
1. Registro online.
Lerecomendamos que registre su nuevo
aparato MUSICGroup justo después de
su compra accediendo a la página web
behringer. com. Elregistro de su compra a
través de nuestro sencillo sistema online
nos ayudará a resolver cualquier incidencia
que se presente a la mayor brevedad
posible. Además,aproveche para leer
los términos y condiciones de nuestra
garantía, siesaplicable en sucaso.
2. Averías. En el caso de que no
exista un distribuidor MUSICGroup en
las inmediaciones, puede ponerse en
contacto con el distribuidor MUSICGroup
de su país, queencontrará dentro del
apartado “Support” de nuestra página web
behringer. com. En caso de que su país no
aparezca en ese listado, acceda a la sección
“Online Support” (quetambiénencontrará
dentro del apartado “Support” de nuestra
páginaweb) y compruebe si su problema
aparece descrito y solucionado allí.
Deforma alternativa, envíenos a través
de la página web una solicitud online de
soporte en periodo de garantía ANTES de
devolvernoselaparato.
3. Conexiones de corriente.
Antes de enchufar este aparato a una salida
de corriente, asegúrese de que dicha salida
sea del voltaje adecuado para su modelo
concreto. En caso de que deba sustituir un
fusible quemado, deberáhacerlo por otro de
idénticas especicaciones, sinexcepción.
1. Enregistrez-vous enligne.
Prenezle temps d’enregistrer votre
produit MUSICGroup aussi vite que
possible sur le site Internet behringer. com.
Lefait d’enregistrer le produit en ligne
nous permet de gérer les réparations
plus rapidement et plus ecacement.
Prenezégalement le temps de lire les
termes et conditions de notregarantie.
2. Dysfonctionnement. Si vous
n’avez pas de revendeur MUSICGroup près
de chez vous, contactez le distributeur
MUSICGroup de votre pays: consultez la
liste des distributeurs de votre pays dans
la page “Support” de notre site Internet
behringer. com. Si votre pays n’est pas
dans la liste, essayez de résoudre votre
problème avec notre “aideen ligne”
que vous trouverez également dans la
section “Support” du site behringer. com.
Vouspouvez également nous faire parvenir
directement votre demande de réparation
sous garantie par Internet sur le site
behringer. com AVANT de nous renvoyer
leproduit.
3. Raccordement au secteur.
Avant de relier cet équipement au secteur,
assurez-vous que la tension secteur de
votre région soit compatible avec l’appareil.
Veillez à remplacer les fusibles uniquement
par des modèles exactement de même
taille et de même valeur électrique — sans
aucuneexception.
Important information Aspectos importantes
Informations
importantes
1. Online registrieren.
Bitteregistrieren Sie Ihr neues
MUSICGroup-Gerät direkt nach dem Kauf
auf der Website behringer. com. Wenn
Sie Ihren Kauf mit unserem einfachen
online Formular registrieren, können
wir Ihre Reparaturansprüche schneller
und ezienter bearbeiten. Lesen Sie
bitte auch unsere Garantiebedingungen,
fallszutreend.
2. Funktionsfehler. Sollte sich
kein MUSICGroup Händler in Ihrer Nähe
benden, können Sie den MUSICGroup
Vertrieb Ihres Landes kontaktieren, der auf
behringer. com unter “Support” aufgeführt
ist. Sollte Ihr Land nicht aufgelistet sein,
prüfen Sie bitte, ob Ihr Problem von
unserem “Online Support” gelöst werden
kann, den Sie ebenfalls auf behringer. com
unter “Support” nden. Alternativ reichen
Sie bitte Ihren Garantieanspruch online
auf behringer. com ein, BEVOR Sie das
Produktzurücksenden.
3. Stromanschluss. Bevor Sie das
Gerät an eine Netzsteckdose anschließen,
prüfen Sie bitte, obSie die korrekte
Netzspannung für Ihr spezielles Modell
verwenden. Fehlerhafte Sicherungen
müssen ausnahmslos durch Sicherungen
des gleichen Typs und Nennwerts
ersetztwerden.
1. Registre-se online. Porfavor,
registreseu novo equipamento
MUSICGroup logo após a compra visitando
o site behringer. com Registrar sua compra
usando nosso simples formulário online
nos ajuda a processar seus pedidos de
reparos com maior rapidez e eciência.
Além disso, leia nossos termos e condições
de garantia, caso sejanecessário.
2. Funcionamento Defeituoso.
Casoseufornecedor MUSICGroup não
esteja localizado nas proximidades, você
pode contatar um distribuidor MUSICGroup
para o seu país listado abaixo de “Suporte”
embehringer. com. Se seu país não estiver
na lista, favor checar se seu problema pode
ser resolvido com o nosso “SuporteOnline”
que também pode ser achado abaixo
de “Suporte”em behringer. com.
Alternativamente, favorenviar uma
solicitação de garantia online em
behringer. com ANTES da devolução
doproduto.
3. Ligações. Antes de ligar a unidade
à tomada, assegure-se de que está a
utilizar a voltagem correcta para o modelo
em questão. Osfusíveis com defeito
terão de ser substituídos, sem qualquer
excepção, porfusíveis do mesmo tipo e
correntenominal.
Weitere wichtige
Informationen
Outras Informações
Importantes
43Quick Start Guide42 EUROCOM MA4008/MA4000M
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
Responsible Party Name: MUSIC Group Services USInc.
Address: 18912 North Creek Parkway,
Suite 200 Bothell, WA 98011, USA
Phone/Fax No.: Phone: +1 425 672 0816
Fax: +1 425 673 7647
EUROCOM MA4008/MA4000M
complies with the FCC rules as mentioned in the followingparagraph:
This equipment has been tested and found to comply with the limits
for a ClassB digital device, pursuant to part 15 of the FCC Rules.
Theselimits are designed to provide reasonable protection against
harmful interference in a residential installation. Thisequipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
Ifthis equipment does cause harmful interference to radio or television
reception, whichcan be determined by turning the equipment o and
on, theuser is encouraged to try to correct the interference by one or
more of the followingmeasures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician forhelp.
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
includinginterference that may cause undesired operation.
Important information:
Changes or modications to the equipment not expressly approved by
MUSIC Group can void the user’s authority to use the equipment.
EUROCOM MA4008/MA4000M
45Quick Start Guide44 EUROCOM MA4008/MA4000M
installed sound
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Behringer EUROCOM MA4000M Quick start guide

Behringer
Brand
Behringer
Model
EUROCOM MA4000M
Category
Soundbar speakers
Type
Quick start guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents