Bradley Frequency FL-2L Installation guide

P.O. Box 309, Menomonee Falls, WI USA 53052-0309

PHONE 800.BRADLEY (800.272.3539) FAX 262.251.5817

bradleycorp.com

Installation

215-1512 Rev. G; ECM 11-08-011

Page 1 of 34 2/15/2012

FL-2H, FL-2L

Frequency

®

Lavatory System

Système de lavabos Frequency

®

Sistema de lavabo Frequency

®

U.S. Pat. No. Des. 477,060

507,634

527,809

537,927

7,039,963

Table of Contents

Pre-Installation Information ..............................2

Components .........................................3

Dimensions ........................................4–5

Rough-ins for FL-2H ...................................6

Rough-ins for FL-2L ....................................7

Lavatory Deck Mounting ................................8

Drain and P-Traps .....................................9

Faucet Battery Box ...................................10

Optional Tankless Water Heater .........................10

End Outlet and Continuous Waste .......................11

Adjust Temperature with Water Running ...................11

Optional Trap/Transition Covers .........................12

Cleaning and Maintenance Instructions ...................12

Table des matières

Avant l’installation ....................................13

Composants ........................................14

Dimensions ......................................15–16

Mises en place des canalisations pour FL-2H ............... 17

Mises en place des canalisations pour FL-2L ...............18

Lavabo .............................................19

Drain et siphon en P ..................................20

Compartiment des piles de robinets ......................21

Chauffage d’eau sans réservoir en option ..................21

Sortie en bout et évacuation continue .....................22

Faire couler l'eau pour régler la température ................22

Siphon/Couvercles de transition en option .................23

Instructions de nettoyage et d’entretien pour Terreon .........23

Contenido

Información previa a la instalación .......................24

Componentes de la cubierta del lavabo ...................25

Dimensiones .....................................26–27

Colocación de tuberías empotradas del FL-2H ..............28

Colocación de tuberías empotradas del FL-2L ..............29

Montaje de la cubierta del lavabo ........................30

Desagüe y sifón en P .................................31

Caja de batería de la llave ..............................32

Calentador de agua sin tanque opcional ...................32

Salida del extremo y desechos continuos ..................33

Ajuste la temperatura con el agua corriendo ................ 33

Sifón/Cubiertas de transición opcionales ..................34

Instrucciones de limpieza y mantenimiento para Terreon ......34

FL-2H

FL-2L

FL-2H, FL-2L Installation

2 2/15/2012 Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011

IMPORTANT!

Read this entire installation manual to ensure proper installation.

When finished with the installation, file this manual with the owner or

maintenance department. Compliance and conformity to local codes

and ordinances is the responsibility of the installers.

Separate parts from packaging and make sure all parts are accounted

for before discarding any packaging material. If any parts are

missing, do not begin installation until you obtain the missing parts.

Make sure that all water supply lines have been flushed and then

completely turned off before beginning installation. Debris in supply

lines can cause valves to malfunction.

Turn OFF electrical power to the electrical outlets, then unplug all

electrical units prior to installation. Electrical power MUST remain off

until installation is complete. After installation is complete, turn on

the water supply ﬁrst, then turn on the electrical power.

Hardware provided by installer must be appropriate for wall

construction. Wall anchors must have a minimum pull-out rating of

1,000 lbs.

Product warranties may be found under “Products” on our Web site

at bradleycorp.com.

THIS

SIDE

UP

Packing List

•

Installation

Supplies Required:

• (6)3/8"wallanchors,boltsand1"min.O.D.washerstomountmainframeandbowltowall(minimumpull-outratingof

1,000 lbs.)

• (2)#10wallanchors(foroptionalmixingvalve/bracketmounting)

• 1/2"Nominalcoppertubingforhot/coldortemperedsupplypiping

• 1-1/2"NPTdrainpiping

• OPTIONAL:110voltGFCIprotectedelectricaloutletfor100–120VACplug-intransformer(forBradleyFaucets)

• OPTIONAL:240/208or277voltsforelectrictanklesswaterheater

Installation FL-2H, FL-2L

Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011 2/15/2012 3

Components

Prepack Trap Cover FL-2

(S45-2109 - Gray)

(S45-2109A - Putty)

(S45-2109B - Coal)

FL-2H (187-269)

(contact Bradley for color options)

FL-2L (187-270)

(contact Bradley for color options)

Transition Cover

(186-1459 - Gray)

(186-1459A - Putty)

(186-1459B - Coal)

Soap Dispenser

Model 6334

Support Bracket - Left

(140-823L)

Support Bracket - Right

(140-823R)

#10 Washer

(142-002AT)

#10-24 Screw

(P18-054)

Standard Waste

Assembly

Offset Strainer

(269-1751)

Offset Strainer

(269-1751)

End Outlet 1-½"

(269-1743)

P-Trap

(269-1697)

Optional

Single-Unit

Adapter

(153-443)

Aerada™ 1200 Series

CS Faucet

Model S53-315

Optional Tankless Water Heater

(269-1767 - EX95TMLB, 240/208 volts)

(269-1768 - EX100TMLB, 277 volts)

Navigator

®

TMV Assembly

Bracket

(140-1041)

Screw

160-447

Valve

(S01-526)

Optional

Tempered Line

½" Flexible Hose

(269-2053)

Stop Valve

(S27-340)

FL-2H, FL-2L Installation

4 2/15/2012 Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011

Dimensions - Front and Top Views

FL-2H shown

FL-2L is similar

FL-2H

FL-2L

60"

(1524mm)

30"

(762mm)

15"

(381mm)

7¾"

(197mm)

22"

(559mm)

30" (762mm) ADA

15" (381mm)

ADA

4"

(102mm)

34"

(864mm)

ADA

32"

(813mm)

12¼"

(311mm)

30"

(762mm)

36"

(914mm)

37¾"

(959mm)

30" (762mm) ADA

4"

(102mm)

15" (381mm)

ADA

34"

(864mm)

ADA

32"

(813mm)

12¼"

(311mm)

30"

(762mm)

36"

(914mm)

37¾"

(959mm)

Installation FL-2H, FL-2L

Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011 2/15/2012 5

Dimensions - Side Views

TAS

22" (559mm)

19½" (495mm)

14"

(356mm)

37¾"

(959mm)

4½"

(114mm)

12¼"

(311mm)

30"

(762mm)

34"

(864mm)

Rim

Height

Standard

Height

22" (559mm)

19½" (495mm)

14"

(356mm)

34¾"

(883mm)

4½"

(114mm)

9¼"

(235mm)

27"

(686mm)

31"

(787mm)

Rim

Height

Juvenile

Height

Ages 6-12

22" (559mm)

19½" (495mm)

14"

(356mm)

33¾"

(857mm)

4½"

(114mm)

8¼" (210mm)

26"

(660mm)

30"

(762mm)

Rim

Height

TAS Height

Grades Pre-K

through 5 or 6

22" (559mm)

19½" (495mm)

14"

(356mm)

33¾"

(857mm)

4½"

(114mm)

10¼" (260mm)

28"

(711mm)

32"

(813mm)

Rim

Height

TAS Height

Grades 6 through

8 or 9

FL-2H, FL-2L Installation

6 2/15/2012 Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011

1a

Rough-Ins for FL-2H

Code Description Qty.

A

3

⁄8"LavDeckAnchorswithaMinimumPull-OutForceof1,000lbs. 6

B #10WallAnchors/FastenersforMountingTrap/TransitionCovers 5

H, C ½"NominalCopperTubingforHot/ColdSupplies,Stub-Out2"FromWall 1

D #10WallAnchors/FastenersforValveMounting 2

E 110vGFIProtectedElectricalOutlet 1

W

1½"NPTDrain,stubout2"fromwall(forcombined drain)

NOTE: For individual drains, refer to page 9.

1

Rim Height

Vertical Height Adjustments for codes A–E,

H, C and W

Fixture Style

34" 0 Standard Height

32" Subtract2" TAS,Grades6through8or9

31" Subtract3" TAS,Pre-KthroughGrades5or6

30" Subtract4" Juvenile Height

27

7

⁄8"

(708mm)

27

7

⁄8"

(708mm) 7"

(178mm)

26"

(660mm)

2

1

⁄8" (54mm)

2

1

⁄8" (54mm)

26"

(660mm)

½"

(13mm)

33"

(838mm)

30"

(762mm)

24"

(610mm)

26

3

⁄8"

(670mm)

1

3

⁄8"

(35mm)

17"

(432mm)

4"

(102mm)

20"

(508mm)

10"

(254mm)

Tempered Line

A

B

D

H

C

E

W

Recommended 2240v/208v or 277v Electrical

Rough-In Location (approx. 6" x 6")

15¾"

(400mm)

25"

(635mm)

29"

(737mm)

32"

(813mm)

28"

(711mm)

31"

(787mm)

Installation FL-2H, FL-2L

Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011 2/15/2012 7

1b

Rough-Ins for FL-2L

Rim Height

Vertical Height Adjustments for codes A–E,

H, C and W

Fixture Style

34" 0 Standard Height

32" Subtract2" TAS,Grades6through8or9

31" Subtract3" TAS,Pre-KthroughGrades5or6

30" Subtract4" Juvenile Height

Code Description Qty.

A

3

⁄8"LavDeckAnchorswithaMinimumPull-OutForceof1,000lbs. 6

B #10WallAnchors/FastenersforMountingTrap/TransitionCovers 5

H, C ½"NominalCopperTubingforHot/ColdSupplies,Stub-Out2"FromWall 1

D #10WallAnchors/FastenersforValveMounting 2

E 110vGFIProtectedElectricalOutlet 1

W

1½"NPTDrain,stubout2"fromwall(forcombined drain)

NOTE: For individual drains, refer to page 9.

1

27

7

⁄8"

(708mm)

27

7

⁄8"

(708mm)

7"

(178mm)

26"

(660mm)

26"

(660mm)

2

1

⁄8" (54mm)

2

1

⁄8" (54mm)

½" (13mm)

31"

(787mm)

28"

(711mm)

24"

(610mm)

26

3

⁄8"

(670mm)

1

3

⁄8"

(35mm)

17"

(432mm)

4"

(102mm)

15¾"

(400mm)

10"

(254mm)

Tempered Line

20"

(508mm)

Recommended 2240v/208v or 277v Electrical

Rough-In Location (approx. 6" x 6")

29"

(737mm)

25"

(635mm)

32"

(813mm)

30"

(762mm)

33"

(838mm)

A

B

D

H

C

E

W

FL-2H, FL-2L Installation

8 2/15/2012 Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011

2

Lavatory Deck

Backing Information

16"

(406mm)

Metal Studs

Drywall

66"

(1676mm)

12"

(305mm)

25"

(635mm)

Securely fasten

plywood to at

least (3) metal

studs (plywood

to equal thickness

of drywall, ½"

minimum

Use

3

⁄8"

toggle bolts

and washers to

secure the support

bracket to plywood

(2) places.

Refer to the rough-ins to determine wall-mounting location for

optional mixing valve.

Installer may prefer to install the faucet before mounting the

ﬁxture to the wall.

If necessary, adjust the ﬁxture height

before securing to the support brackets.

Installation FL-2H, FL-2L

Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011 2/15/2012 9

3a

Drain and P-Trap

FL-2L shown

FL-2H is opposite

3b

Individual P-Traps

Rubber

Friction

Nut

Tailpiece

5"

(127mm)

Rubber

Friction

Tailpiece

Nut

1½"

(38mm)

Top View

Rotate

60°

Rotate

60°

30" (762mm) Ref.

NOTE: FL-2H: Remove 4" from right side tailpiece only.

FL-2L: Remove 4" from left side of tailpiece only.

1½" Drain

Stub Out 2" from

Wall (2) Places

20"

(508mm)

3½" Max.

(2) Places

FL-2H is shown; FL2L is similiar.

FL-2H, FL-2L Installation

10 2/15/2012 Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011

4

Faucet Battery Box

5

Optional Tankless Water Heater

B

Install the faucets

according to the

manufacturer's

instructions.

A

Mount the Faucet

Battery Boxes to the

wall at desired locations.

Faucet Valve Control Module

½" Flexible Hose (qty. 3)

(269-653)

½" Tee

(269-1150)

Cold

Hot

Mixing Valve

¾"

(19mm)

Electric Tankless

Water Heater

Outlet

Inlet

20½"

(521mm)

Finished Floor

Installation FL-2H, FL-2L

Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011 2/15/2012 11

6

End Outlet and Continuous Waste

FL-2L shown

FL-2H is opposite

TOP VIEW

FRONT VIEW

25" (508mm) REF.

7

Adjust Temperature with Water Running

H

C

A

LoosenCapScrewabout1/4"(4-6

turns) and lift up cover (do not

remove).

B

Using cover, turn cartridge gently until

desired water temperature is reached.

Do not turn past stops as this may

damage unit. Push cover down and

tighten screw.

This valve is NOT factory preset. Upon installation, the temperature of this

valve must be checked and adjusted to ensure delivery of a safe water

temperature. Water in excess of 110°F (43°C) may cause scalding.

FL-2H, FL-2L Installation

12 2/15/2012 Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011

Cleaning and Maintenance for Terreon

Material Description: Terreon is an NAHB Certiﬁed densiﬁed solid surface material composed of polyester resin and is resistant

to chemicals, stains, burns and impact. Surface damage can be easily repaired with everyday cleansers or ﬁne grit abrasives.

Routine Cleaning: Clean daily or as often as conditions require using a standard commercial or household cleaner such as

Formula 409

®

or Windex

®

.

Stubborn Stains: Remove tough stains with Ajax

®

, Comet

®

, or Soft-Scrub

®

and a green Scotch-Brite

®

pad or lightly sand in a

circular motion with 240 grit wet/dry sandpaper. The ﬁnish can be renewed with a maroon Scotch-Brite

®

pad.

Special Situations for Terreon Material

Scratches: Remove scratches with a green Scotch-Brite

®

pad. The ﬁnish can then be renewed with a maroon Scotch-Brite

®

pad, followed by a white Scotch-Brite

®

pad or 30-micron sandpaper.

Hard Water Deposits: Remove hard water deposits with a mild solution of vinegar and water. Always rinse the unit

thoroughly after cleaning.

Restoring the surface: Use Hope’s

®

Solid Surface cleaner and polish to refresh and protect the Terreon Solid Surface

material. Bradley recommends additional care and maintenance for the darker colored Terreon. For additional information,

visit bradleycorp.com.

Do not use strong acid or alkaline chemicals and cleansers to clean Terreon. If these chemicals come in

contact with the surface, wipe them off immediately and rinse with soapy water. Avoid contact with harsh

chemicals such as paint remover, bleach, acetone, etc. Avoid contact with hot pans and objects.

Repair Kits: Terreon repair kits are available. Contact your Bradley representative or distributor for part numbers and pricing

Repair kits are made to order and have a shelf life of 30 days.

Terreon is a unique, cast solid surface material. Aggregate ﬂow and distribution as well as shades of color can vary from

product to product creating natural characteristics.

Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement,

nor does the omission of any brand name cleaner imply inadequacy. Many products named are regional in distribution, and

can be found in local supermarkets, department and hardware stores, or through your cleaning service. It is emphasized that

all products should be used in strict accordance with package instructions.

8

Optional Trap/Transition Covers

A

Turn on the water and test the unit

for leaks and proper operation.

B

Secure the transition cover through

the vertical slot with hardware

provided.

C

Trim the trap covers (at inside scoring only!)

with a high-speed rotary tool and 1/8 radius

tip bit (or very sharp knife). Clean burrs.

D

Position the trap covers

over the transition cover

and secure to the wall

with hardware provided.

DO NOT

TRIM!!!

DO NOT

TRIM!!!

Page is loading ...

Installation FL-2H, FL-2L

Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011 2/15/2012 15

Dimensions - Vues de face et de dessus

FL-2H

FL-2L

FL-2H est montrée

FL-2L est similaire

60"

(1524mm)

30"

(762mm)

15"

(381mm)

7¾"

(197mm)

22"

(559mm)

30" (762mm) ADA

15" (381mm)

ADA

4"

(102mm)

34"

(864mm)

ADA

32"

(813mm)

12¼"

(311mm)

30"

(762mm)

36"

(914mm)

37¾"

(959mm)

30" (762mm) ADA

4"

(102mm)

15" (381mm)

ADA

34"

(864mm)

ADA

32"

(813mm)

12¼"

(311mm)

30"

(762mm)

36"

(914mm)

37¾"

(959mm)

Page is loading ...

FL-2H, FL-2L Installation

26 2/15/2012 Bradley Corporation • 215-1512 Rev. G; ECM 11-08-011

Dimensiones - Vista frontal y superior

FL-2H

FL-2L

FL-2H se muestra

FL-2L es similar

60"

(1524mm)

30"

(762mm)

15"

(381mm)

7¾"

(197mm)

22"

(559mm)

30" (762mm) ADA

15" (381mm)

ADA

4"

(102mm)

34"

(864mm)

ADA

32"

(813mm)

12¼"

(311mm)

30"

(762mm)

36"

(914mm)

37¾"

(959mm)

30" (762mm) ADA

4"

(102mm)

15" (381mm)

ADA

34"

(864mm)

ADA

32"

(813mm)

12¼"

(311mm)

30"

(762mm)

36"

(914mm)

37¾"

(959mm)

Page is loading ...

Bradley Frequency FL-2L Installation guide

This manual is also suitable for

Bradley Frequency FL-2L Installation guide

in other languages

Related papers

Other documents