Alcatel-Lucent 7210 SAS-D Installation guide

Brand: Alcatel-Lucent

Model: 7210 SAS-D

Category: Networking

Type: Installation guide

7210 SAS-D

NSTALLATION GUIDE

December 2011

Document Part Number: 93-0348-01-04

*93-0348-01-04*

No portion of this document may be reproduced in any form or means without prior written permission from Alcatel-Lucent.

Information in this document is proprietary and confidential to Alcatel. The information in this document is subject to change. All

trademarks and registered trademarks are the property of the respective owners.

USA Requirements Only

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at his own expense.

Canadian Requirements Only

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Réglement sur le matériel brouilleur du Canada.

Japan/Nippon Requirements Only

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to

take adequate measures.

Caution:

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser

radiation exposure.

VCCI-A

7210 SAS-D Installation Guide Page 3

Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

7210 SAS-D Overview

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Switch Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Switch Architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Network Management Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connectivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

AC Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

DC Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Ethernet Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Air Ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Power Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

External Power Modules (ETR-Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

System and Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Power Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Physical Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Installing the 7210 SAS-D

Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Selecting a Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Ethernet Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Equipment Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Installing Your Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Rack Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Desktop or Shelf Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Grounding the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Connecting to a Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Connecting to an AC Power Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Connecting to a DC Power Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Connecting to the Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Installing the Optional External Power Supply (ETR only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Installation Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Locking Mechanisms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Installing SFPs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Removing SFPs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Configuring the 7210 SAS-D

Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

TABLE OF CONTENTS

Page 4 7210 SAS-D Installation Guide

Table of Contents

Post Installation Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Initializing the System and Downloading Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Booting a 7210 SAS-D in the Lab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Booting a 7210 SAS-D using the image on Flash (with the image shipped by factory) . . . . . . . . . 54

Booting a 7210 SAS-D from the Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Downloading the TiMOS software to the internal flash. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Establishing Switch Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Console Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Telnet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Running Telnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Troubleshooting

Diagnosing Switch Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Power Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

In-Band Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Appendix A: Specifications

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

7210 SAS-D Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

7210 SAS-D ETR Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Japan VCCI Class A Declaration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

RoHS and WEEE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Appendix B: Console Connection

Console Port Pin Assignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

7210 SAS-D Installation Guide Page 5

LIST OF TABLES

Preface

Table 1: Information Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

7210 SAS-D Overview

Table 2: 7210 SAS-D AC Chassis Front Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Table 3: 7210 SAS-D DC Chassis Front Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Table 4: Power LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Table 5: External AC Power Module Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Table 6: External DC Power Module Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Table 7: Location of System and Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Table 8: System LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Table 9: 100/1000 Fiber-Optic SFP and 10/100/1000Base-T Copper Port LEDs . . . . . . . . . . . . . . . . . . .27

Table 10: Front Panel Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Installing the 7210 SAS-D

Table 11: Serial Cable Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Configuring the 7210 SAS-D

Table 12: Console Configuration Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Troubleshooting

Table 13: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Appendix A: Specifications

Table 14: 7210 SAS-D Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Table 15: 7210 SAS-D Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

Appendix B: Console Connection

Table 16: Serial Cable Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Page 6 7210 SAS E Ethernet Service Switch

List of Tables

7210 SAS-D Installation Guide Page 7

LIST OF FIGURES

7210 SAS-D Overview

Figure 1: 7210 SAS-D AC Chassis Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Figure 2: 7210 SAS-D DC Chassis Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Figure 3: 7210 SAS-D ETR AC Chassis Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Figure 4: 7210 SAS-D ETR DC Chassis Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Figure 5: 7210 SAS-D AC Chassis Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Figure 6: 7210 SAS-D ETR AC Chassis Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Figure 7: 7210 SAS-D DC Chassis Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Figure 8: 7210 SAS-D ETR DC Chassis Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Figure 9: AC and DC Power Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Figure 10: External AC Power Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Figure 11: External DC Power Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Figure 12: Location of the System and Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Figure 13: Location of the Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Installing the 7210 SAS-D

Figure 14: Attaching the Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Figure 15: Installing the Switch in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Figure 16: Attaching the Adhesive Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Figure 17: Wall Mounting the Chassis using the Wall Mounting Screws . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Figure 18: Connecting a -48 VDC Power Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Figure 19: Connecting a +24 VDC Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Figure 20: Attaching the External Power to the Chassis Using the Mounting Kit (Front View) . . . . . . . . . .43

Figure 21: Attaching the External Power to the Chassis Using the Mounting Kit (Rear View). . . . . . . . . . .44

Figure 22: Connecting the Power Cable from the External Power Module to the Chassis . . . . . . . . . . . . .44

Configuring the 7210 SAS-D

Figure 23: 7210 SAS-D Boot Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Troubleshooting

Appendix A: Specifications

Appendix B: Console Connection

Page 8 7210 SAS-D Installation Guide

List of Figures

7210 SAS-D Installation Guide Page 9

Preface

About This Manual

This guide provides site preparation recommendations, step-by-step procedures to

rack mount the Alcatel-Lucent 7210 SAS-D

, and instructions to install and configure

the 7210 SAS OS software.

Each 7210 SAS-D switch is shipped with a console cable, power cord (AC or DC) and

rubber feet. Optionally, a rack-mounting bracket kit, a wall-mounting bracket kit, and

external AC or DC power module and bracket kit (ETR-only) are available for order.

Warnings and Notes

Observe the warnings and notes to avoid injury or switch damage during installation

and maintenance. Follow the safety procedures and guidelines when working with and

near electrical equipment. Warning statements and notes are provided in each chapter.

Audience

This guide is intended for network installers and system administrators who are

responsible for installing, configuring, or maintaining networks. This guide assumes

you are familiar with electronic and networking technologies.

Preface

Page 10 7210 SAS-D Installation Guide

Information Symbols

Table 1 describes symbols contained in this guide.

Technical Support

If you purchased a service agreement for your 7210 SAS-D and related products from a

distributor or authorized reseller, contact the technical support staff for that distributor or

reseller for assistance. If you purchased an Alcatel-Lucent service agreement, contact technical

assistance at:

Web: http://www1.alcatel-lucent.com/comps/pages/carrier_support.jhtml

Table 1: Information Symbols

Symbol Meaning Description

Danger This symbol warns that improper handling and installation could result in bodily

injury. An electric shock hazard could exist. Before you begin work on this

equipment, be aware of hazards involving electrical circuitry, networking

environments, and instigate accident prevention procedures.

Caution This symbol warns that improper handling and installation could result in

equipment damage or loss of data.

Warning This symbol warns that improper handling may reduce your component or

system performance.

Note This symbol provides additional operational information.

Class 1 laser products are listed in the MDA installation guides. Only approved

Class 1 replaceable laser transceivers should be used with this product.

Class 1 Laser Product

7210 SAS-D Installation Guide Page 11

7210 SAS-D Overview

This chapter describes the 7210 SAS-D features and includes the following sections:

•"Introduction" on page 12

•"Switch Features" on page 13

•"Switch Architecture" on page 15

•"Features" on page 16

•"Hardware Description" on page 18

Introduction

Page 12 7210 SAS-D Installation Guide

Introduction

7210 SAS-D is an ethernet demarcation and backhaul unit with support for 4 x 10/100/1000 Base-

T fixed ports and 6 x 100/1000 SFP ports, for use typically as a customer premise unit (CPE). It

supports line-rate switching on all the ports. It is a service-aware Ethernet switch with support for

QinQ layer-2 uplinks. It has an integrated power supply and supports fan-less operation.

It is available in two variants:

• 7210 SAS-D supporting normal operating temperature range (i.e. 0º C to 40º C). Its

primary application, is for use as a CPE/demark unit in delivery of business services. 7210

SAS-D is available with either a AC or DC power supply.

• 7210 SAS-D ETR supporting extended temperature range (i.e. -40º C to 65º C), is targeted

for applications requiring an extended temperature range. This unit has a stratum-3

Oscillator to allow for support of SyncE and 1588v2. Its primary application is in use for

mobile back haul. 7210 SAS-D ETR will be available with three power supply options as

given below:

 A DC unit supporting -48V DC power supply with an optional external backup power

supply

 A DC unit supporting +24V DC power supply with an optional external backup power

supply

 An AC unit with an optional external backup supply.

7210 SAS-D Overview

7210 SAS-D Installation Guide Page 13

Switch Features

The 7210 SAS-D is a service-aware Layer 3 switch. It supports up to 10 connections including 6

100/1000 fiber-optic SFP ports and 4 10/100/1000 Base-T fixed copper ports. The chassis is

available with either an AC power module or DC power module, as shown in the following

illustrations:

Figure 1: 7210 SAS-D AC Chassis Front Panel

Figure 2: 7210 SAS-D DC Chassis Front Panel

The ETR-variant chassis is also available with either an AC power module or DC power module,

as shown in the following illustrations:

7210SASac_0001

7210SASdc_0001

Switch Features

Page 14 7210 SAS-D Installation Guide

Figure 3: 7210 SAS-D ETR AC Chassis Front Panel

Figure 4: 7210 SAS-D ETR DC Chassis Front Panel

All of the 7210 SAS-D variant chassis include the following features:

• 6 100/1000 fiber-optic SFP ports and 4 10/100/1000 Base-T fixed copper ports

• One RJ-45 console (RS-232 interface) connector for device management

• Embedded SR OS

• Compact size: 1RU height, 10-inch rack-mountable metal enclosure, 7-inch depth (ETSI)

7210SASac_0008

7210SASdc_0008

7210 SAS-D Overview

7210 SAS-D Installation Guide Page 15

Switch Architecture

The 7210 SAS-D employs a wire-speed, non-blocking switching fabric. This permits simultaneous

wire-speed transport of multiple packets at low latency on all ports. The switch also features full-

duplex capability on all ports, that effectively doubles the bandwidth of each connection.

Network Management Options

This switch contains a comprehensive array of LEDs for at-a-glance monitoring of network and

port status. It also includes a management agent that enables you to configure or monitor your

switch using its CLI, or by using SNMP applications.

To manage the switch, you can make a direct connection to the console port (out-of-band) or you

can manage it by using a network connection (in-band) using Telnet/SSH or SNMP-based network

management software.

Features

Page 16 7210 SAS-D Installation Guide

Features

The 7210 SAS-D includes the following features:

• Wire speed, non-blocking, service-aware Ethernet switch

• 6 100/1000 fiber-optic SFP ports and 4 10/100/1000 Base-T copper ports

• Powered by SR OS for feature-rich Carrier Ethernet VPN services

• Per-service quality of service (QoS) with up to eight levels of class-based queuing per port

• Per-service OAM toolkit with IEEE 802.1ag, IEEE 802.3ah and local service mirroring

• Ethernet features include IEEE 802.1Q and QinQ (stacked VLAN IDs)

• Dual homed connections uplinks to separate aggregation devices

• Flexible deployment options with support for mesh and ring topologies

• MEF 9 and MEF 14 compliant platform

• Managed by the 5620 SAM

• Supports intergrated AC or DC power supply.

• The chassis does not use a fan for cooling.

7210 SAS-D ETR variant supports the following, in addition to the above features:

• Supports extended temperature range (i.e. -40º C to 65º C) of operation

• Supports stratum-3 oscillator onboard, allowing for support of SyncE and 1588v2

• Supports an optional backup power supply for all the power supply options supported with

ETR variant.

Note: 7210 SAS-D ETR hardware is capable of supporting Synchronous Ethernet and 1558v2.

Please check the release notes for software support.

7210 SAS-D Overview

7210 SAS-D Installation Guide Page 17

Connectivity

The 7210 SAS-D includes the following connectivity features:

• 100/1000 fiber-optic SFP ports and 10/100/1000Base-T copper SFP ports full-duplex

connections. The SFP ports allow for use of 10/100/1000 Base-T copper SFPs.

• Auto-negotiation on 10/100/1000 Base-T fixed copper ports enables each port to

automatically select the optimum speed and communication mode (half or full duplex) if

this feature is supported by the attached device.

• IEEE 802.3-2005 Ethernet, Fast Ethernet and Gigabit Ethernet compliance ensures

compatibility with standards-based network cards and switches from any vendor.

Hardware Description

Page 18 7210 SAS-D Installation Guide

Hardware Description

The chassis is available with either an AC power module or DC power module, as shown in the

following illustrations.

AC Chassis

Figure 5: 7210 SAS-D AC Chassis Front Panel

Figure 6: 7210 SAS-D ETR AC Chassis Front Panel

7210SASac_0001A

5 63

7210SASac_0001A

5 63

7210 SAS-D Overview

7210 SAS-D Installation Guide Page 19

The following section describes the front panel features of the 7210 SAS-D AC chassis:

Table 2: 7210 SAS-D AC Chassis Front Panel Features

Key Description

1 Power, System, and Port LEDs

2 100/1000 SFP ports

3 10/100/1000Base-T fixed copper ports

4 RJ-45 Console port

5 Power switch

6 AC power connection

7 Chassis ground connection point

Hardware Description

Page 20 7210 SAS-D Installation Guide

DC Chassis

Figure 7: 7210 SAS-D DC Chassis Front Panel

Figure 8: 7210 SAS-D ETR DC Chassis Front Panel

7210SASdc_0001A

5 63

7210SASdc_0001A

5 63

Page is loading ...

Alcatel-Lucent 7210 SAS-D Installation guide

Brand: Alcatel-Lucent

Model: 7210 SAS-D

Category: Networking

Type: Installation guide

Download PDF

report

Alcatel-Lucent 7210 SAS-D Installation guide

Alcatel-Lucent 7210 SAS-D Installation guide

Related papers

Other documents