CIB 7102
Voice Terminal Installation
Instructions
CIB 7102
Issue 1
7102A Voice Terminal Installation Instructions
Checklist of Parts
Your package should include the following items:
ITEM
7102A Voice Terminal
Handset
Handset Cord
Graphic Panel
Face Plate
Line Cord
Desk Stand/Wall Mount Assembly
COMCODE
105330419
105158885
104211305
845786839
845786821
103732558
846028520
Reference Documents
AT&T System 75, System 75 XE, and System 85—Terminal and
1
2
3
4
Adjuncts—Installation and Test, 555-015-104
AT&T System 75, System 75 XE, and System 85—Terminal and
Adjuncts—Reference Manual, 555-015-201
AT&T System 75 7102A Voice Terminal User’s Instructions,
555-200-728
AT&T System 85 7102A Voice Terminal User’s Instructions,
555-103-715
Desk Installation
To install your terminal, you will need cutting pliers.
1
Assemble the desk stand. The pieces of the desk stand come
attached to one another.
●
Cut the runner away from the base using cutting pliers. Twist out
the desk support piece.
iss 1, 7102A VT-1
Desk
Support
Runner
Wall
Support
Base
FIGURE 1
●
Find the slots labeled A and B on the bottom of the base. Turn
the base over so the rubber feet are down.
●
Insert the tabs labeled A and B on the desk support into the
corresponding slots on the base.
Desk Support
Tab A
Tab B
Base
FIGURE 2
●
Hold the stand so that its mounting slots fit just below the terminal
mounting slots.
iss 1, 7102A VT-2
Mounting
Slots
Mounting
Tabs
Line Jack
Stand
Terminal
(bottom view)
Locking
Tabs
Stand attached
to Terminal
(bottom view)
FIGURE 3
●
Slide the stand upward so that the terminal tabs fit securely in the
3 stand mounting slots.
Ringer
Volume
Control
Desk Support
Rubber Feet
FIGURE 4
Locate a modular wall jack within 7 feet of your desk or table.
2
3
Insert one of the plugs on the line cord into the LINE jack underneath
the terminal. Insert the other end of the line cord into a modular wall
jack.
iss 1, 7102A VT-3
Ringer
Volume
Control
Handset
Jack
Jack
Handset Cord
Jack
Line Cord
FIGURE 5
4
5
Insert one of the plugs on the handset cord into the jack on the bot-
tom front of the terminal. Insert the other end of the handset cord
into the jack on the handset.
Flex the plastic window over the number card to remove it. Write or
type your telephone number on the card. Replace the card and win-
dow. Install the access codes card and the faceplate cover.
Wall Installation
To mount your terminal on a wall, you may need a hammer, a drill and a
1/8” drill bit, four 1/8” x 2” screws and mounting sleeves, cutting pliers,
and a screwdriver.
Assemble the wall mount. The pieces of the wall mount come
1
attached to one another.
●
●
●
Cut the runner away from the base using cutting pliers. Twist out
the wall support piece.
Use a screwdriver to remove the 4 rubber feet from the base.
Turn the base upside down on a table and insert first tab B, then
tab A on the wall support piece into the corresponding slots on
the base.
iss 1, 7102A VT-4
●
Lift the base and push the wall support through the slots until the
tabs click into place. Turn the base over.
Tab B
Tab A
Bottom
of Base
FIGURE 6
2
3
4
5
6
7
8
9
Locate a modular wall jack within 7 feet of where you want to mount
the terminal.
If the terminal will be mounted on a plaster or sheetrock wall, locate a
wall stud nearest the desired mounting site. Center the base on the
stud. Use the screw holes in the four corners of the base to mark
screw locations on the wall over the stud. If necessary, drill out the
holes in the base to make them larger.
NOTE: If the terminal is to be mounted on any other surface, use
appropriate mounting hardware.
Using a 1/8” drill bit, drill a hole at each of the 4 marked screw loca-
tions on the wall.
Insert one sleeve into each of the 4 drilled holes. Use a hammer to
tap each sleeve until it is flush with the wall.
With the base flush against the wall, line up the holes in the base with
the sleeves. Insert screws through the base into the top 2 holes and
partially thread the screws into the sleeves. Insert the other 2 screws
into the lower 2 holes.
Tighten all 4 screws. The wall mount should now be fastened
securely.
Flex the plastic window covering the telephone number card and
remove it. Put the plastic window and card aside. Loosen the screw
beneath the number card. Remove the screw and lift out the
retainer.
Rotate the retainer and replace it so that the smooth side faces up.
Replace the screw. Write or type your telephone number on the
iss 1, 7102A VT-5
card. Replace the card and plastic window. Install the access codes
card and the faceplate cover.
Handset
Retainer
Handset
Retainer
Handset Retainer
Screw
Remover
Handset
Retainer
After
Rotation
Handset
Retainer
Screw
FIGURE 7
10
11
Follow the instructions in steps 2 through 4 of the DESK INSTALLA-
TION section for connecting the line cord and the handset cord and
preparing the terminal for use.
Hold the terminal so that the mounting tabs fit just above the mount-
ing slots on the wall mount. Arrange the line cord so that it runs
down the wall behind the terminal. Then, slide the terminal down so
that the tabs fit securely into the slots of the wall mount.
Controls and Display
1
Set the ringer volume control to the midpoint so you will be able to
hear the terminal ring.
Testing
1
Pick up the handset and listen for the dial tone. It can take a few
moments for the switch to initially recognize the terminal and supply
dial tone.
●
●
If you do not hear a dial tone, depress the switchhook several
times and check that both cords are connected firmly at both
ends.
If you still do not hear a dial tone, contact your company’s
telecommunications manager.
iss 1, 7102A VT-6
Warranty
All terms and conditions specified in your agreement with AT&T apply.
Hearing Aid Compatibility
This terminal is compatible with inductively coupled hearing aids
prescribed by the Federal Communications Commission.
iss 1, 7102A VT-7
/