Haier HLH26ATBB - 26" LCD TV Owner's manual

Please READ this manual carefully before

operating your TV, and retain it for future

reference.

TFT-LCD TV

OWNER S MANUAL'

MODEL :HLH26A TBB

HLH32ATBB

HLH266BB

HLH326BB

S

2 TFT-LCD TV

THIS SYMBOL INDICATES THAT HIGH VOLTAGE IS PRESENT

INSIDE. IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT

WITH ANY INSIDE PART OF THIS PRODUCT.

WARNING : To reduce the risk of electric shock do not remove cover or back.

No user-serviceable parts inside refer service to qualified service personnel.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, use and

can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However ,there is no

guarantee that interference with not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encourage to try to correct the interference by one or

more of the following measures:

*Reorient or relocate the receiving antenna.

*Increase the separation between the equipment and receiver.

*Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

*Consult the dealer or an experienced radio/TV technician for help.

This device compiles with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may be not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

FCC CAUTION:

To assure continued compliance and possible undesirable interference, the provided ferrite

cores must be used when connecting this plasma display to video equipment; and maintain

at least 40cm spacing to other peripheral device.

CANADIAN NOTICE:

This Class B digital apparatus compiles with Canadian ICES-003.

RISK ELECTRIC SHOOK

DO NOT OPEN

WARNING

Safety of operators has been taken into consideration at the design and manufacture

phase, but inappropriate operation may cause electric shock or fire. To prevent the product

from being damaged, the following rules should be observed for the installation, use and

maintenance of th product. Read the following safety instruction before starting the operation.

The User Manual uses the following symbols to ensure a safe operation and prevent

any damage to operators or properties:

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT

OPERATING AND MAINTENANCE INSTRUCTIONS IN THE

LITERATURE ACCOMPANYING THE APPLIANCE.

FCC STATEMENT

Owner s Manual 3

IMPORTANT SAFETY INSTRUCTIONS

Read all of the instructions before using this appliance. When using this

appliance, always exercise basic safety precautions, including the following:

1)Save these Instructions ---the safety and operating instructions should be

retained for future reference.

2)All warning on the appliance and in the operating instructions should be followed.

3)Cleaning --- Unplug from the wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use only dry cloth for cleaning.

4)Attachments ---do not use attachments not recommended by the manufacturer

as they may cause hazards.

5)Water and moisture -- do not place this product near water, for example, near a

bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a

swimming pool.

6)Accessories ---do not place this unit on an unstable cart, stand, tripod, bracket,

or table. Use only with a cart, stand, tripod, bracket, or table recommend by the

manufacture, or sold with the unit.

7)Ventilation ---Slots and openings in the cabinets and the back or bottom are

provided for ventilation. These openings must not be blocked. In a built in

installation such a bookcase or rack do not install product unless proper ventilation

is provided.

8)Power Source ---this TV should be operated only from the type of power source

indicated on the rating label. If you are not sure of the type of power supply to your

home, consult your appliance dealer or local power company.

9)Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet. To prevent electric shock, ensure

the grounding pin on the AC cord power plug is securely connected.

10)Power cord protection ---Power supply cords should be routed so that they are

not likely to be walked on or pinched by items placed upon or against them. Pay

particular attention to cords or plugs, convenience receptacle, and the point where

they exit from the appliance.

11)Lighting precaution ---for added protection for this product during a lighting

storm or when it is left unattended for long period of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will prevent damage to the

product due to lighting and power line surges.

12)Never push objects of any kind into this product through openings as they may

touch dangerous voltage point or short out parts that could result in a fire or electric

shock. Avoid spilling liquid of any kind on the product.

13)Servicing ---do not attempt to service the product by yourself, as opening or

removing covers may expose you to dangerous voltage or other hazards. Refer all

servicing to authorized service personnel.

14)Unplug this unit from the wall outlet and refer servicing to qualified service

personnel under the following conditions:

a. When the power supply cord or plug is damaged or frayed.

b.If liquid has been spilled, or objects have been fallen into the unit.

c.If the unit has been exposed to rain or water.

d.If the unit does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operating instructions, as

improper adjustment of other controls may result in damage and will often

require extensive work by a qualified technician to restore the unit to its normal

operation.

e.If the unit has been dropped or damaged in any way.

f.When the unit exhibits a distinct change in performance; this indicates a need

for service.

15)Heat --- The product should be situated away heat source such as radiators, heat

registers, stoves, or other products (Including amplifiers) that product heat.

16)Overloading ---Do not overload wall outlets and extension cord as this can result

in a risk of fire or electric shock.

SAVE THESE INSTRUCTIONS

Thank you for using our Haier product. This easy-to-use manual will guide you in

getting the best use of your product. Remember to record the model and serial

number. They are on label in back of the unit.

Model number

serial number

Date of purchase

Staple your receipt to your manual. You will need it to obtain warranty service.

4 TFT-LCD TV

Contents

Introduction

Owner s Manual 5

War nin g . . . . . . . ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . .

Saf ety I nst ruc tio ns . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Introduction

Con tro ls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... ... ... ... ..

Connection Options . . . . . . . . . . . . . . . . . . . . . .............

Universal Remote Controller . ............ . . . . . . . . ......

Installation

Acc ess ori es . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... ... ... ..

Antenna Connection . . . . . . . . . . ..............................

VCR Connectio. . . . . . . . . . . . . . . . . . . . . ................. ..

External A/V Source Setup . . . . .. . . . . ......................

DVD Connection . . . . . ...... . . . . . . . . . . . . . ................

DTV Connection.....................................................

Digital Audio Output . . . . . . . . . . . . . . . . . . . . ..............

PC Connection. . . . . . . . . . . . . . . . . . . . . . . ................

Monitor Out Setup . . . . . . . . . . . . . . . . . . . . ............... .

HDM I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..... ... ... ... ... .

Cable sample.........................................................

Connecting Headphones . . . . . . . . . . . . . . . . . . . ....... .

Pow er so urc e.. ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . . . .

Operation

Switching On/Off the TV set . . . . . ... . . . . . . . . . . . ... ...

Choose the Menu Language . . . . ..... .......................

Choose the input source.........................................

Channel Menu

Automatic Scan. . . . . . . . . . . . . ............................. . .

Man ual S can . . . . ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . .. .

Fine tune................................................................

Edi t Pro gra m.. ... ... ... ... . . . . . . . . . . . . . . . . . . . . . . . . . ..

S . . . . . ........... ............ . . ..

S . . .............. . . . ............ . . ..

Mute .............. . . . ............................................ . . ..

Video Menu

Aspect Ratio Control . . . . . . . . . . . . . . . . . . . . .. . . .. . . ..

Audio Menu

SAP Broadcasts Setup............................................

elect the desired program

elect the desired sound

How to select picture modes.....................................

How to customize your own picture status .................

How to select audio modes......................................

How to customize your own audio status ..................

Timer Menu

Function Menu

Closed Captions.....................................................

CC mode...............................................................

........................................................

DTV Caption..........................................................

DTV Caption Style..................................................

.........................................................

...........................................................

..................................................

Menu

Screen Setup for PC mode......................................

Lock Menu

rating and categories.......................

Others Functions

EPG (Electronic Program Guide) . . . . . . . . . . . . .........

Bri ef In fo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ... ... ... . .

Veiwing Picture- in- Picture

Other function

Maintenance . . ... ... . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .

Warranty ................................................................

Date /Time setting...................................................

Timer on setting......................................................

Timer off setting......................................................

Sleep Timer setting.................................................

Time zone setting...................................................

Daylight Saving setting...........................................

NTSC Caption

OSD Timeout

Blue screen

OSD transparency

Adjust

.....................................

Quick program view.................................................

Setting up your remote control ..................................

Remote Control Codes ............................................

Parental Control

Manufactured under license from Dobly Laboratories. "Dobly" and the

double-D symbol are trademarks of Dobly Laboratories. Confidential

unpublished works.

Front panel controls

-This is a simplified representation of front panel.

-Here shown may be somewhat different from your TV.

1.

2.

3.

4.

5.

6. Remote control signal receive window.

7.Remote Indicator In red when standby mode, in blue when display.

INPUT:

CH( ) Program plus and minus, menu options

VOL( ) Volume increase and decrease, menu reset and entry

MENU Menu display

all input source display and OK confirm.

POWER : Is used to activate the display or return to standby mode.

Controls

1.INPUT: all input source display and OK confirm.

2.CH ( ) : program minus and plus, menu options

3.VOL ( ): volume decrease and increase , menu reset and entry

4.MENU: menu display

5. POWER : Is used to activate the display or return to standby mode.

6.Power indicator: in red when standby mode, in blue when display.

7.Remote control signal receive window

HLH266BB

HLH26ATBB

The buttons are on the bottom of the TV set)

INPUT CH VOL MENU

1

INPUT

2

3

4

5

6

7

Introduction

6 TFT-LCD TV

HLH32ATBB

HLH326BB

VIDEO

R

AUDIO

L

AUDIO2 Input

connect to hear

stereo sound from an

external device.

VIDEO2 Input

Connects the video signal

from a video device.

MENU

CH

VOL

Back panel controls

Connection Options

HLH266BB

HLH26ATBB

DVI Input

Connect the monitor

output connector from

a PC to the appropriate

input port.

Power Cord Socket

This TV operates on AC power.

The voltage is indicated on the

Specifications page. Never attempt

to operate the TV on DC power

PC

Audio In

PrPb

Y

DVI Audio In

AC IN

DVD/DTV Input

(Component )

Connect a component

video/audiodevice to

these jacks.

Earphone jack:

Earphone audio

output terminal.

Audio input

for linking PC audio

frequency output terminals.

PC VIDEO Input

Connect the monitor

output connector from

a PC to the jack

Antenna Input

Connect cable or

antenna signals to

the TV, either directly

or through your

cable box.

HDMI

Optical

YPbPr

Audio In

LR

Headphone

out

S-Video

S-Video Input

Connect SVideo

out from

an S-VIDEO

device to the S-VIDEO

input.

Digital Audio Output

Connect digital audio

from various types of

equipment. Note: In

standby mode,

these ports will not

work.

CVBS

S-video/CVBS

Audio In

LR

RL V

AV OUT

R INPUT

F

HDMI/DVI

connect a

DVI(Video)

signal to

HDMI/DVI.

DVI Input

Connect the monitor

output connector from

a PC to the appropriate

input port.

Power Cord Socket

This TV operates on AC power.

The voltage is indicated on the

Specifications page. Never attempt

to operate the TV on DC power

PC

Audio In

PrPb

Y

DVI Audio In

AC IN

DVD/DTV Input

(Component )

Connect a component

video/audiodevice to

these jacks.

Earphone jack:

Earphone audio

output terminal.

Audio input

for linking PC audio

frequency output terminals.

PC VIDEO Input

Connect the monitor

output connector from

a PC to the jack

Antenna Input

Connect cable or

antenna signals to

the TV, either directly

or through your

cable box.

HDMI

Optical

YPbPr

Audio In

LR

Headphone

out

S-video

S-Video Input

Connect SVideo

out from

an S-VIDEO

device to the S-VIDEO

input.

Digital Audio Output

Connect digital audio

from various types of

equipment. Note: In

standby mode,

these ports will not

work.

CVBS

S-video/CVBS

Audio In

LR

RL V

AV OUT

R INPUT

F

HDMI/DVI

connect a

DVI(Video)

signal to

HDMI/DVI.

Introduction

Owner s Manual 7

AUDIO OUT

HLH326BB

HLH32ATBB

Caption output

AUDIO Input

connect to hear

stereo sound from an

external device.

VIDEO Input

Connects the video

signal from a

video device.

AUDIO/VIDEO

output

AUDIO output

AUDIO Input

connect to hear

stereo sound from an

external device.

VIDEO Input

Connects the video

signal from a

video device.

AUDIO/VIDEO

output

SELECT

CH.LIST

FAV.LIST

AUDIO LIST

PIP SWAP

AUDIO SWAP

POSITION

CC

P .MODE

S.MODE

FREEZE

E

N

U

UIDE

NPUT

INFO

E

X

IT

R

A

C

S

A

P

S

L

E

P

VOL+

CH+

Q.VIEW

OK

VO

L

-

CH-

POWER

Turns your TV or any other programmed

equipment on or off, depending on mode.

- The remote controller cannot be operated unless the batteries are properly loaded.

Function introduction

- When using the remote control, aim it at the remote control sensor on the TV.

SAP

Selects MTS sound: Mono, Stereo, and SAP in Analog

mode. Change the audio language in DTV mode.

Introduction

8 TFT-LCD TV

Favorite

Open the favorite channel list. Select the subchannel

THUMBSTICK

(Up/Down/Left/Right/OK)

Allows you to navigate the on-screen menus and adjust

the system settings to your preference.

CHANNEL UP/DOWN

Selects available channels

PAGE UP/PAGE DOWN

Moves from one full set of screen

Renamermation to the next one.

P.MODE

Selects a factory preset picture mode

depending on the viewing environment.

FREEZE

Freezes the currently-viewed picture, but audio continues.

Press FREEZE button again to resume the normal picture.

ARC

(Aspect Ratio Control)

Changes the aspect ratio.

It is no available in PIP mode.

S.MODE

Selects the sound appropriate for the program's

character.

VOLUME UP/DOWN

Increases/decreases the sound level.

Digits

press to change the channel.

EXIT

Clears all on-screen displays and

returns toTV viewing from any menu.

INPUT

show the input source mode.

MUTE

Switches the sound on or off

CC(closed caption)

Select a closed caption:

CC MUTE, CC ON, CC OFF.

GUIDE

Shows program schedule.

INFO

When you watch the TV, press the key, the information

displays on bottom of the screen.

MENU

Brings up the main menu to the screen.

PIP function buttons

PIP:Selects PIP, POP and main Window;

SWAP:In PIP and POP mode, swap the

main and sub window;

AUDIO SWAP: In PIP and POP mode,

swap the audio of main and sub window;

PIP position: To select sub picture

position for PIP.

SLEEP button

Displays the Sleep Timer option.

Q.VIEW

Switch the current channel to the last channel

you have viewed, or switch the other source to TV.

CH.LIST

Open the channel list.

Universal Remote Controller

TV DVD VCR SETBOX CABLE AUDIO

Press the SELECT button repeatedly to select one of the

system modes in which the remote control can be used.

When the desired device is selected, the corresponding

LED lights on 5seconds.

VCR/DVD Functions

/ Rewind / Fast

/

Control some video cassette recorders or DVD players.

backward /Forward

Stop

Play/Pause

REC

AUDIO.LIST

Open the audio channellist.

- button

Press to select additional channels

(digital and analog)

being broadcast by the same station.

For example, to select channel

“54-3”, press “54”, then press “-” and “3”.

Electric Torch key

Press and hold Electric Torch key, white LED will be ON, release

this key, white LED will be OFF.

Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an

outdoor antenna .In different places, the suitable antenna type and position are different.

External Equipment Connections

Antenna Connection

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

Wall Antenna

Socket

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

Outdoor

Antenna

VHF Antenna

UHF Antenna

Turn clockwise to tighten.

RF Coaxial Wire (75 ohm)

Bronze Wire

Be careful not to bend the bronze wire when

connecting the antenna.

Bronze Wire

To improve the picture quality in a poor signal area,

please purchase a signal amplifier and install properly.

If the antenna needs to be split for two TV`s, install a 2-

Way Signal Splitter in the connections.

If the antenna is not installed properly, contact your dealer

for assistance.

Installation

Owner s Manual 9

Accessories

Remote controller

User's manual

Alkaline battery(AAA) 2

Power cable

SELECT

CH.LIST

FAV.LIST

AUDIO LIST

PIP SWAP

AUDIO SWAP

POSITION

CC

P.MODE

S.MODE

FREEZE

E

N

U

ID

E

N

P

U

T

IN

F

O

E

X

I

T

R

A

C

S

A

P

S

L

E

P

VOL+

CH+

Q.VIEW

OK

VO

L

-

CH-

Please READ this manual carefully before

operating your TV, and retain it for future

reference.

TFT-LCD TV

OWNER S MANUAL'

MODEL :HLH26ATBB

HLH32ATBB

HLH266BB

HLH326BB

S

VCR connection

NOTE: All cables shown are not included with the TV.

There are several ways to connect your television, depending on the components you want to connect

and the quality of the signal you want to achieve. The following are examples of some ways to connect

your TV. Choose the connection which is best for you.

External Equipment Connections

Choose Your Connection

Note:

Do not connect to both Video and

S-Video at the same time.

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV

Connection Option 1

Set VCR output switch to channel 3 or 4 and

then tune the TV to the same channel number.

Connection Option 2

1. Connect the audio and video cables from the

VCR's output jacks to the TV input jacks, as

shown in the figure.

When connecting the TV to VCR, match the

jack colors (Video = yellow, Audio Left = white,

and Audio Right = red).

If you connect an S-VIDEO output from VCR to

the S-VIDEO input, the picture quality is

improved; compared to connecting a regular

VCR to the Video input.

2. Insert a video tape into the VCR and press

PLAY on the VCR. (Refer to the VCR owner`s

manual.)

3. Select the input source with using the

INPUT button on the remote control, and

then press / button to select the source,

press the button to confirm.

S-Video

CVBS

S-Video/CVBS

Audio In

LR

RL V

AV OUT

R INPUT

F

Installation

10 TFT-LCD TV

Pr Pb

Y

DVI Audio IN

YPbPr

Audio In

LR

Headphone

out

S-Video

CVBS

S-Video/CVBS

Audio In

LR

How to connect

1. Connect the DVD video outputs (Y, Pb/Cb, Pr/Cr) to the Y, Pb,

Pr jacks on the TV and connect the DVD audio outputs to the

YPbPr Audio IN jacks on the TV, as shown in the figure.

2. If your DVD only has an S-VIDEO output jack, connect this

to the S-VIDEO input on the TV. as shown in the figure.

NOTE: If your DVD player does not have component video

output, use S-Video.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the INPUT button on the remote control to select YPbPr

mode.

3. Press Play button on external equipment for program play.

4. Refer to the DVD player's manual for operating instructions.

DVD connection

External Equipment Connections

How to connect

Connect the audio and video cables from the external equipment's

output jacks to the TV input jacks, as shown in the figure.

When connecting the TV to external equipment, match the

jack colors (Video = yellow, Audio Left = white, and Audio

Right = red).

How to use

1. Select the input source with using the INPUT button on

the remote control.

2. Press the / button to select the desired source.

3. Press the or ok button to confirm

2. Operate the corresponding external equipment.

External A/V Source Setup

Video Game Set

Camcorder

Component Input ports

To get better picture quality, connect a DVD player to the component

input ports as shown below.

S-Video

CVBS

S-Video/CVBS

Audio In

LR

RL V

AV OUT

R INPUT

F

Installation

Owner s Manual 11

Component ports

on the TV

Video output ports

on DVD player

Y Pb Pr

Y B-Y R-Y

Y Cb Cr

Y P P

BR

PC

Audio In

Pr Pb

Y

DVI Audio IN

HDMI

Optical

YPbPr

Audio In

LR

Headphone

out

Digital Set-top Box

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital

signals from a digital set-top box or other digital external device, refer to the figure as shown below.

- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).

How to connect

Use the TV`s (Y, PB, PR) , VGA or HDMI

jack for video connections, depending on

your set-top box connector. Then, make

the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the owner`s

manual for the digital set-top box.)

2. Use INPUT on the remote control to select

YPbPr, VGA,or HDMI source.

Send the TV`s audio to external audio equipment (stereo system) via

the Digital Audio Output (Optical) port.

How to connect

1. Connect one end of an optical cable to the TV Digital Audio

(Optical) Output port.

2. Connect the other end of the optical cable to the digital audio (optical)

input on the audio equipment.

See the external audio equipment instruction manual for operation.

Note: When connecting with external audio equipments, such as

amplifers or speakers, please turn the TV speakers off.

Digital Audio Output

Caution: Do not look into the optical output port.

Looking at the laser beam may damage

your vision.

External Equipment Connections

DTV connection

HDMI

Optical

YPbPr

Audio In

LR

Headphone

out

Installation

12 TFT-LCD TV

Signal

480i

480p

720p

1080i

YPbPr

Yes

HDMI/DVI

No

Yes

PC

AUDIO

IN

Pr Pb

Y

DVI

Audio IN

HDMI

How to connect

1. To get the best picture quality, adjust the PC graphics card to (>1024

2. Use the TV`s PC or DVI (Digital Visual Interface)Audio IN port for video connections, depending on your PC connector.

If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of eitherVGA r DVI IN to

display the PC on the TV.

If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to eithe DVI; (the other mode is

set to Plug and Play automatically by the TV.)

3. Then, make the corresponding audio connection. If using a sound card, adjust the PC sound as required.

How to use

1. Turn on the PC and the TV.

2. Turn on the display by pressing the POWER button on the TV's remote control.

3. Use INPUT on the remote control to select VGA or HDMI source.

4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode.

If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and

contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic

card or consult the manufacturer of the PC graphic card.

NOTES:

1 Use a DVI cable.

2 Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the

screen.

3 The synchronization input form for Horizontal and Vertical frequencies is separate.

x768),60Hz.

IN o

r VGA or

PC connection

Resolution

Frame

frequency

(Hz)

VGA

SVGA

XGA

640*480 60Hz

800*600 60Hz

1024*768

60Hz

Mode

Resolution

External Equipment Connections

Installation

Owner s Manual 13

75Hz

85Hz

External Equipment Connections

The TV has a special signal output capability which allows you to

hook up a second TV or monitor.

Connect the second TV or monitor to the TV`s AV .

See the Operating Manual of the second TV or monitor for further

details regarding that device`s input settings.

Notes:

YPbPr, VGA, HDMI,DTV input sources

cannot be used for Monitor out.

When connecting with external audio equipments, such as amplifers

or speakers, please turn the TV speakers off.

We recommend to use the video and audio output jacks for VCR

recording.

OUT

Monitor Out Setup

AUDIO OUT

L R

RL V

AV OUT

R INPUT

F

Installation

14 TFT-LCD TV

- HDMITM, the HDMI logo and High-Definition Multimedia Interface is a trademark or registered trademark of HDMI Licensing."

- This TV can receive the High-Definition Multimedia Interface(HDMI) or the Digital Visual Interface(DVI).

- This TV supports HDCP(High-bandwidth Digital Contents Protection) Protocol for 720x480p, 1280x720p, and 1920x1080i resolution.

- When you connect this TV with a source device(DVD player, Set Top Box or PC) supporting Auto HDMI/DVI function, the output

resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto HDMI/DVI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the DVD Player or Set Top Box's output resolution to 1280x720p, and the PC graphics card's

output resolution to 1024x768, 60Hz.

- If the source device has an HDMI output, no other audio connection is necessary because HDMI-to-HDMI connection includes

both video and audio.

- If the source device has a DVI output and no HDMI output, a separated audio connection is necessary.

How To Connect

1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product).

2. No separated audio connection is necessary.

How To Use

- If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto HDMI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Select HDMI input source in input source option of Select Main source menu.

How To Connect

1. Connect the source device to HDMI port of this TV with a HDMI-to-DVI cable(not supplied with this product).

2. A separated audio connection is necessary.

3. If the source device has a fiber optic digital audio output, connect the audio output to DIGITAL AUDIO(Optical) port for DVI

INPUT.

4. If the source device has an analog audio output connector, connect the source device audio output to DVI Audio In port located on the

left side of HDMI port.

How To Use

- If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto DVI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Press the INPUT button to select HDMI input source in input source option of Select Main source menu.

HDMI

Installation

Owner s Manual 15

Cable sample

HDMI Cable

(not supplied with the product)

HDMI to DVI Cable

(not supplied with the product)

Analog Audio Cable(RCA type)

(not supplied with the product)

Analog Audio Cable

(Stereo to RCA type)

(not supplied with the product)

Installation

16 TFT-LCD TV

YPbPr

Audio In

LR

Headphone

out

S-VIDEO

Power source

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for

operation on AC. Insert the AC cord plug into

a standard polarized AC outlet.

NOTES:

Never connect the AC line cord plug to other

than the specified voltage. Use the

attached power cord only.

If the polarized AC cord does not fit into a non-

polarized AC outlet, do not attempt to file or cut

the blade. It is the user`s responsibility to have

an electrician replace the obsolete outlet.

If you cause a static discharge when touching

the unit and the unit fails to function, simply

unplug the unit from the AC outlet and plug it

back in. The unit should return to normal operation.

Polarized AC Cord Plug

AC Outlet

Wider Hole

and Blade

You can connect a set of headphones to your set if you wish to watch a

TV programme without disturbing the other people in the room.

Connecting Headphones

External Equipment Connections

Note

Prolonged use of headphones at a high volume

may damage your hearing.

You will not receive sound from the speakers

when you connect headphones to the system.

Plug a set of headphones into the 3.5mm

mini-jack socket on the rear panel of the set.

Installation

Owner s Manual 17

Switching On/Off the TV set

Choose the Menu Language

When you start using your set for the first time, you must select the language which will be used for displaying menus

and indications.

-In the manual, the OSD (on screen display) may be different from your TV`s, because it is just an

example to help you with the TV operation.

Operation

-There are several options you might need to set up in order for your TV to work properly. Read the

instructions that follow.

Note:

If the TV in power on , the screen show information according the type of input signal . the information

will disappear. If there is no signal and bluescreen in ON the screen enter in bluescreen and display No signal

on top and center of the screen.

1 Press the MENU button and then use / button to select the

Function menu.

2 Press the button and then use / button to select Menu

Language.

3 Press the button and then use / button to enter the list of

available language. English Spanish or French

4 Select your language with the / button and press the OK

button to confirm you selection.

5 When you are satisfied with your choice, press the EXIT button

to return to normal viewing or press MENU button to return to the

previous menu.

1. First, connect power cord correctly.

2. Select the viewing source by using INPUT button on the remote control.

3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.

4. If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

: Move cursor, /OK: Go to submenu, EXIT/ MENU: Exit main menu

English

Spanish

French

Menu Language English

CC Mode On

NTSC Caption CC1

DTV Caption Service1

DTV caption Style

OSD Timeout Middle

Blue Screen On

OSD transparency Middle

B

C

A

Video

Audio

Time

Channel

Function

Lock

Choose the Input source

- Change the picture source so you can watch your TV, cable TV, VCR, DVD, or any other devices that are

connected to your TV.

1. Press the INPUT button to enter the Select Main picture Source menu

and then use / button to select the desired items. Air TV, ,

SVIDEO, YPBPR, VGA, HDMI.

2. Press the OK button to confirm.

3. Press INPUT button to return to TV viewing or press EXIT button to return to the

previous menu.

VIDEO

Select Main Source

Cable TV

VIDEO1

VIDEO2

SVIDEO

YPBPR

VGA

HDMI

Operation

Note:

1. According to your connection device, you can change the name of every source.

2. In channel menu, if the Tuner item is set ting as Air and Cable, the source menu will display Air TV and Cable TV;

If the Tuner item is setting as the one of the Air and Cable, the source menu will display the one of two.

18 TFT-LCD TV

This TV set has three methods to set channels, which are respectively Auto Scan, manual Scan fine tune.

In this section, how to use the remote control to set channel is explained. You can also use buttons on the TV

set to set channel.

A password is required to gain access to Channel menu if the Lock of Edit program menu is turned on.

Automatic Scan

Note : the Channel menu will be only operated in normal TV mode.

Channel menu

- Automatically finds all channels available through antenna or cable inputs, and

stores them in memory on the All Channel List.

When Air is selected, the TV will detect antenna signals and will

search for antenna TV (NTSC and ATSC) channels available in

your local area.

When Cable is selected, the TV will detect cable company supplied

signals and will search for cable TV (NTSC,ATSC, QAM modulated)

channels available in your area.

Make sure that registration with your cable TV provider and

connection of equipment are completed.

When Air and Cable are selected, the TV will detect the antenna

signals and cable company supplied signals, and search for the

antenna TV and cable TV channels available in your area.

1 Press the MENU button and then use / button to select the

Channel menu.

2 Press the button and then use / button to select Tuner.

3 Press the button and then use / button to Select Cable or

Air mode.

4 Press the OK button

5 When you are satisfied with your choice, press MENU button to

return to the previous menu.

6 Press the / button to select Auto Scan.

7 Press the button and press the OK button to start searching.

8 To cancel searching, press the OK button.

: Move cursor, /OK: Go to submenu, EXIT/ MENU: Exit main menu

B

C

A

Video

Audio

Time

Channel

Function

Lock

Tuner Air

Auto Scan

Manual Scan

Fine Tune

Edit Program

Rename

Air

Cable

B

C

A

Video

Audio

Time

Channel

Function

Lock

OK Cancel

Air Tuner Number: 47

Found: 1

Tuner Air

Auto Scan

Manual Scan

Fine Tune

Edit Program

Rename

Operation

Owner s Manual 19

: Move cursor, OK: Enter, MENU: Return to upper menu,

EXIT: Exit main menu

Manual Scan

Channel menu

If excessive channel signals of unwanted programs are received in local area,

manual search function is recommended.

1 Press the MENU button and then use / button to select the

Channel menu.

2 Press the button and then use / button to select Tuner.

3 Press the button and then use / button to Select Cable or Air

mode.

4 Press the OK button.

5 When you are satisfied with your choice, press MENU button to return

to the previous menu.

6 Press the / button to select Manual Scan.

7 Press the button and then use digital buttons to select channel number you want to add or delete.

8 Press the button to select OK item and press OK button to add or delete for the channel number.

9 Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Fine Tune (only in anolog signal )

1 Press the MENU button and then use / button to select the

Channel menu.

2 Press the / button to select Fine Tune.

3 Press the or OK button

4 Press the button to tune.

5 Press EXIT button to return to TV viewing or press MENU button

to return to the previous menu.

/

: Move cursor, /OK: Go to submenu, EXIT/ MENU: Exit main menu

B

C

A

Video

Audio

Time

Channel

Function

Lock

Tuner Air

Auto Scan

Manual Scan

Fine Tune

Edit Program

Rename

Type

Air

Channel NO

Frequency

0k

4

67.250MHz

: Move cursor, /OK: Go to submenu, EXIT/ MENU: Exit main menu

B

C

A

Video

Audio

Time

Channel

Function

Lock

Tuner Air

Auto Scan

Manual Scan

Fine Tune

Edit Program

Rename

For the tune of the analog channels

Operation

20 TFT-LCD TV

Page is loading ...

Haier HLH26ATBB - 26" LCD TV Owner's manual

This manual is also suitable for

Haier HLH26ATBB - 26" LCD TV Owner's manual

Related papers

Other documents