WAGO I/O-SYSTEM 750 User manual

Type
User manual

This manual is also suitable for

Pos: 2 /Dokumentation allgemein/Einband/Einband Handbuch - Fronts eite 20 15 - mit Doc Var iabl en ( Sta ndar d) @ 9\ mod_1285229289866_0.docx @ 64941 @ @ 1
WAGO-I/O-SYSTEM 750
Manual
750-455(/xxx-xxx)
4AI 4-
20mA S.E.
4-Channel Analog Input Module 4-20 mA, Single
-
ended
Ve
rsion 1.2.0
Pos: 3 /Al le Ser ien ( All ge mein e M odul e)/H in weis e z ur D oku men tati on/I mpr ess um für Sta ndar dh and büch er - al lg. A ngabe n, Ansc hrifte n, Telef onn ummer n und E-Mai l-A dresse n @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1
2 WAGO-I/O-SYSTEM 750
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
© 2015 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: +49 (0) 571/8 87 – 0
Fax: +49 (0) 571/8 87 – 1 69
Web: http://www.wago.com
Technical Support
Phone: +49 (0) 571/8 87 – 5 55
Fax: +49 (0) 571/8 87 – 85 55
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende der Lis te f ür T ext mar ke Ei nb and _vor ne = ==
WAGO-I/O-SYSTEM 750 Table of Contents 3
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 5 /D oku ment ati on al lg emei n/V erz eic hnis se/ Inh alts verz ei chni s - Üb erschr ift oG u nd Verz eich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1
Table of Contents
1 Notes about this Documentation ................................................................. 5
1.1 Validity of this Documentation ................................................................. 5
1.2 Copyright ................................................................................................... 5
1.3 Symbols ..................................................................................................... 6
1.4 Number Notation ....................................................................................... 8
1.5 Font Conventions ...................................................................................... 8
2 Important Notes ........................................................................................... 9
2.1 Legal Bases ............................................................................................... 9
2.1.1 Subject to Changes ............................................................................... 9
2.1.2 Personnel Qualifications ....................................................................... 9
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying
Provisions ............................................................................................. 9
2.1.4 Technical Condition of Specified Devices ......................................... 10
2.2 Safety Advice (Precautions) .................................................................... 11
3 Device Description ..................................................................................... 13
3.1 View ........................................................................................................ 14
3.2 Connectors ............................................................................................... 15
3.2.1 Data Contacts/Internal Bus ................................................................. 15
3.2.2 Power Jumper Contacts/Field Supply ................................................ 16
3.2.3 CAGE CLAMP
®
Connectors ............................................................. 18
3.3 Display Elements .................................................................................... 19
3.4 Operating Elements ................................................................................. 20
3.5 Schematic Diagram ................................................................................. 21
3.6 Technical Data ........................................................................................ 22
3.6.1 Device ................................................................................................. 22
3.6.2 Supply ................................................................................................. 22
3.6.3 Communication .................................................................................. 22
3.6.4 Inputs .................................................................................................. 22
3.6.5 Connection Type ................................................................................ 23
3.6.6 Climatic Environmental Conditions ................................................... 23
3.7 Approvals ................................................................................................ 24
3.8 Standards and Guidelines ........................................................................ 26
4 Process Image ............................................................................................. 27
5 Mounting ..................................................................................................... 28
5.1 Mounting Sequence ................................................................................. 28
5.2 Inserting and Removing Devices ............................................................ 29
5.2.1 Inserting the I/O Module .................................................................... 29
5.2.2 Removing the I/O Module .................................................................. 30
6 Connect Devices ......................................................................................... 31
6.1 Connecting a Conductor to the CAGE CLAMP
®
................................... 31
6.2 Connection Example ............................................................................... 32
7 Use in Hazardous Environments .............................................................. 33
7.1 Marking Configuration Examples ........................................................... 34
7.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 34
4 Table of Contents WAGO-I/O-SYSTEM 750
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
7.1.2 Marking for America According to NEC 500 .................................... 39
7.2 Installation Regulations ........................................................................... 40
7.2.1 Special Conditions for Safe Use (ATEX Certificate TÜV 07 ATEX
554086 X) ........................................................................................... 41
7.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12 ATEX
106032 X) ........................................................................................... 42
7.2.3 Special Conditions for Safe Use (IEC-Ex Certificate TUN 09.0001 X)43
7.2.4 Special Conditions for Safe Use (IEC-Ex Certificate IECEx TUN
12.0039 X) .......................................................................................... 44
7.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01 .. 45
List of Figures ...................................................................................................... 46
List of Tables ........................................................................................................ 47
=== Ende der Lis te f ür T ext mar ke V erzei c hnis _vor ne ===
WAGO-I/O-SYSTEM 750 Notes about this Documentation 5
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 7 /Al le S eri en ( Allg em ein e Mod ul e)/Ü bers chr ift en f ür al l e Ser ien/H i nweis e zur D ok ume ntati on /Hin wei se z u dies er D oku ment ati on - Ü ber schr if t 1 @ 4\ mod_1237987661750_21.docx @ 29029 @ 1 @ 1
1 Notes about this Documentation
Pos: 8 /Al le Ser ien ( All ge mein e M odul e)/H in weis e z ur D oku men tati on/H in weis e/Hi n weis : Do kum ent atio n a ufbe wahr e n @ 4 \mod_1237987339812_21.docx @ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation is
included, if necessary.
Pos: 9 /Al le Ser ien ( All ge mein e M odul e)/Ü ber sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume ntat ion /G ültig keit sb ereic h - Ü ber schri ft 2 @ 12\ mod_1338912448776_21.docx @ 96469 @ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 /S eri e 7 50 ( WA GO-I/O- SYST EM) /Hi n weise z ur Do kum ent ati on/G ülti gkei ts berei ch/ Gül tig kei tsber ei ch D oku men tat ion Bus kle mme 7 50- xxx x, S tan dar dversi on un d au fgel ist ete V ari ant en @ 14\ mod_1358944038682_21.docx @ 109354 @ @ 1
This documentation is only applicable to the I/O module 750-455 (4AI 4-20mA
S.E.) and the variants listed in the table below.
Pos: 11 /Serie 750 (WAGO-I/O-SYST EM)/ Hi nweis e z ur D o kume ntati on/ Gül tig keits b ereic h/ Varia nt enli st en/V ari ant enlis te - 750- xxx - Standardversion und Variante /025-000 (er w eitert er T e mper at urber eic h) @ 9\mod_1281521920414_21.docx @ 63093 @ @ 1
Table 1: Variants
Item Number/Variant
Designation
750-455
4AI 4-20mA S.E.
750-455/025-000
4AI 4-20mA S.E./T
Pos: 12 /Al l e Ser ien (Al lg emei ne M od ule)/H i nweis e zur D okumentation/Hinweise/Hinweis: Gültigkeit der Angaben für aufgelistete Varianten @ 9\mod_1281520778141_21.docx @ 63085 @ @ 1
Documentation Validity for Variants
Unless otherwise indicated, the information given in this documentation applies to
listed variants.
Pos: 13 /Serie 750 (WAGO-I/O-SYST EM )/Hi n weis e zur D okum ent ati on/Hi n weise /Ac htu ng: Hin weis zur D oku ment ati on B uskl e mmen 750- xxxx @ 4\ mod_1237986979656_21.docx @ 29023 @ @ 1
The I/O module 750-455 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 14.1 /All e Seri en ( All ge meine Mo dul e)/Hi n weis e zur D oku ment ati on/U rh eber schu tz aus führ lich @ 4\mod_1235565145234_21.docx @ 27691 @ 2 @ 1
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos: 14.2 /Dokumentation allgemein/Gliederungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
6 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 14.3 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle Ser ie n/Hin wei se z ur D ok ume nta tion/ S ymbol e - Ü bers chr ift 2 @ 13\ mod_1351068042408_21. docx @ 105270 @ 2 @ 1
1.3 Symbols
Pos: 14 .4.1 /Al le Seri en ( All ge meine Mo dul e)/ Wic htig e Er läut eru nge n/ Sich erh eits- und sonstige Hinweise/Gefahr/Gefahr: _Warnung vor Personenschäden allgemein_ - Erläut erung @ 13\mod_1343309450020_21.docx @ 101029 @ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 14 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erlä uteru ngen/ Sich erheit s- und sonsti ge Hinw eise/ Gefa hr/Gef ahr: _ Warnu ng vor Per sonen schä den durc h elek trisc hen Stro m_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 14 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erlä uteru ngen/ Sich erheit s- und sonstige Hinweise/War nung /W arn ung: _W arn ung vor Per so nensc häd en al lg em ein_ - Erläuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 14 .4.4 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erlä uteru ngen/ Sich erheit s- und sonstige Hinwei se/V orsic ht/V orsich t: _War nung vor Pers onensc häden al lge mein_ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 14 .4.5 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erlä uteru ngen/ Sich erheit s- und sonstige Hinweise/Achtung/Achtung: _War nu ng vor S ac hschä den all ge mein _ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 14 .4.6 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erlä uteru ngen/ Sich erheit s- und so nsti ge H inw eis e/Ac htu ng/ Ach tung : _ War nung vor Sac hsc hä den durc h elektrostatische Aufladung_ - Erläuterung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 14 .4.7 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erlä uteru ngen/ Sich erheit s- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21.docx @ 101047 @ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 14 .4.8 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erlä uteru ngen/ Sich erheit s- und so nsti ge H inw eis e/Inf or mat ion/I nf or matio n: _Wei ter e Inf or mati on allg emei n_ - Erl äuter ung @ 13 \mod_1343310439814_21.doc x @ 101051 @ @ 1
WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos: 14.5 /Dokumentation allgemein/Glieder ungs ele men te/---Sei te nwec hsel--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1
8 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 14 .6 /All e Seri en (Allg emeine Modul e)/Hi nweis e zur Do kument ation /Zahl ensys teme @ 3\ mod_1221059454015_21.docx @ 21711 @ 2 @ 1
1.4 Number Notation
Table 2: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
Pos: 14.7 /All e Seri en ( All ge meine Mo dul e)/Hi n weis e zur Dokumentation/Schriftkonventionen @ 3\mod_1221059521437_21. docx @ 21714 @ 2 @ 1
1.5 Font Conventions
Table 3: Font Conventions
Indicates
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu items are marked in bold letters.
e.g.: Save
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 15 /Dokum entat ion all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Important Notes 9
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 16 /Al l e Ser ien (Al lg emei ne M od ule)/Ü b ersc hrif te n für all e Seri en/Wic htig e Erläut erung en/ Wichti ge Erlä uteru ngen - Üb ersc hrift 1 @ 4\ mod_1241428899156_21. docx @ 32170 @ 1 @ 1
2 Important Notes
Pos: 17.1 /All e Seri en ( All ge meine Do kum ente) ( Allg emei ne Mo dule) /Wi cht ige Erl äut eru nge n/Wi chti ge Erl äut eru nge n - Einl eit ung @ 3\mod_1221059818031_21.docx @ 21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 17.2 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle Ser ie n/Wi chti ge Erl äuter u ngenR ec htlic he Gr undlag en - Üb ersc hrift 2 @ 3\ mod_1221060626343_21.docx @ 21726 @ 2 @ 1
2.1 Legal Bases
Pos: 17.3 /Alle Serien (Allgemeine Dokumente) ( Allgemei ne Module)/Wichtige Erläuterungen/Änderungs vorbehalt - Übersc hrift 3 un d In halt @ 3\ mod_1221060036484_21.docx @ 21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos: 17.4 /Serie 750 (WAGO-I/O-SYST EM)/ Wicht ige Erl äuter unge n/Pers onalq uali fikati onPer sonal quali fikat ion 750- xxxx - Ü bersc hrift 3 u nd Inh alt @ 3\mod_1224061208046_21.docx @ 24063 @ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: 17.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Bestimmungsgemäße Verwendung Bestimmungsgemäße Verwendung 750-xxxx - Üb ers chrif t 3 un d In hal t @ 3 \mod_1224064151234_21.docx @ 24070 @ 3 @ 1
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information
in the section “Device Description> “Standards and Guidelines” in the manual
for the used fieldbus coupler/controller.
10 Important Notes WAGO-I/O-SYSTEM 750
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos: 17.6 /All e Seri en ( All ge meine Mo dul e)/ Wic htig e Er läut eru nge n/T echni sc her Zus tan d d er G erät e - Ü bersc hrift 3 un d Inh alt @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. WAGO
Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of
changes in hardware or software as well as to non-compliant usage of devices.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos: 17.7 /Dokumentation al lge mei n/Gli eder ungs ele men te/---Sei te nwec hsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Important Notes 11
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 17 .8 /All e Seri en (Allg emeine Modul e)/Über schr ifte n für alle S erie n/Wich tige Er läuter ung enSic herhei tshi nweise - Über schri ft 2 @ 6\mod_1260180299987_21.docx @ 46 724 @ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 17.9 /All e Seri en ( All ge meine Do kum ente) ( Allg emei ne Mo dule) /Wi cht ige Erl äut eru nge n/Si cher hei tshi n weis e/Ei nl eitung S ich erhei tshin weis e Hard ware @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 17.1 0. 1 /Al le S eri en ( Allg em eine D o ku ment e) (Al lg emei ne M o dul e)/ Wich tige Erl äuter u ngen /Sic her hei ts hinw eise /G efahr /G efahr : N ich t an Ger äte n unt er Spa nnung arbeite n! @ 6\mod_1260180365327_21.docx @ 46727 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 17 .10. 2 /Serie 75 0 (WAG O-I/O-S YST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onst ige H i nwei se/ Gef ahr/ Gefa hr: Ei nbau 07 50- xxxx nur in Geh äusen, Schrä nken oder ele ktrisc hen Betr iebsr äume n! @ 6\mod_1260180556692_21.docx @ 46731 @ @ 1
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: 17.1 0. 3 /Al le S eri en ( Allg em eine D o ku ment e) (Al lg emei ne M o dul e)/ Wich tige Erl äuter u ngen /Sic her hei ts hinw eise /G efahr /G efahr : U nfal lv erh ütung sv orsc hri ften beachten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1
Pos: 17.1 0. 4 /Al le S eri en ( Allg em eine D o ku ment e) (Al lg emei ne M o dul e)/ Wich tige Erl äuter u ngen /Sic her hei ts hinw eise /G efahr /G efahr : A uf normg er echt e n Ansc hlu ss ac hten! @ 6 \mod_1260180753479_21.docx @ 46739 @ @ 1
Pos: 17.1 1. 1 /Al le S eri en ( Allg em eine D o ku ment e) (Al lg emei ne M o dul e)/ Wich tige Erl äuter u ngen /Sic her hei ts hinw eise /Ac htu ng/Ac ht ung : Defek te oder besch ädigte G erät e austaus chen! @ 6\mod_1260180857358_21.docx @ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos: 17.1 1. 2 /Al le S eri en ( Allg em eine D o ku ment e) (Al lg emei ne M o dul e)/ Wich tige Erl äuter u ngen /Sic her hei ts hinw eise /Ac htu ng/Ac ht ung : G erät e vor kriec hen den und i sol ier end en S to ffen s chütz en! @ 6\mod_1260181036216_21.docx @ 46747 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos: 17.1 1. 3 /Al le S eri en ( Allg em eine D o ku ment e) (Al lg emei ne M o dul e)/ Wich tige Erl äuter u ngen /Sic her hei ts hinw eise /Ac htu ng/Ac ht ung : Rei nig ung nur mi t zul äss ige n M ater ial ien! @ 6\mod_1260181203293_21.docx @ 46751 @ @ 1
Clean only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos: 17.1 1. 4 /Al le S eri en ( Allg em eine D o ku ment e) (Al lg emei ne M o dul e)/ Wich tige Erl äuter u ngen /Sic her hei ts hinw eise /Ac htu ng/Ac ht ung : Kei n K ont akts pra y verw end en! @ 6\ mod_1260181290808_21.docx @ 46755 @ @ 1
12 Important Notes WAGO-I/O-SYSTEM 750
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 17.1 1. 5 /Al le S eri en ( Allg em eine D o ku ment e) (Al lg emei ne M o dul e)/ Wich tige Erl äuter u ngen /Sic her hei ts hinw eise /Ac htu ng/Ac ht ung : Ver pol ung ver mei de n! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 17.1 1. 6 /Al le S eri en ( Allg em eine D o ku ment e) (Al lg emei ne M o dul e)/ Wichtig e Erlä uteru ngen/Si cher heits hinw eise/Ac htu ng/Ac htung : Elektr ostati sch e Entla dung ver meid en! @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 18 /Dokum entat ion all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 13
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 19 /Al l e Ser ien (Al lg emei ne M od ule)/Ü b ersc hrif te n für all e S eri en/G erä teb esc hreib ung /G erä tebe schr eib ung - Üb ersc hrift 1 @ 3\mod_1233756084656_21.docx @ 27096 @ 1 @ 1
3 Device Description
Pos: 20.1 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Einleitung/Anwendung/AI/Anwendung 750- 04xx AI SE (4...20mA) @ 5\mod_1245846703678_21.docx @ 35930 @ @ 1
The Analog Input Module 750-455 (4AI 4-20mA S.E.) processes analog signals
with the norm value of 4 mA ... 20 mA.
Pos: 20.2 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-Bes chr eibu ng/ AI/I /O- Beschr eib ung 750- 04xx 4 AI SE Fel ddsig nale über AI1 und M asse bz w. AI2/ 3/4 und M asse @ 5\ mod_1246370579270_21.docx @ 36366 @ @ 1
The module has 4 input channels. The signals of the field side may be received via
the CAGE CLAMP
®
connectors AI 1 and common (ground) or AI 2, AI 3, AI 4
and common (ground) each.
The common (ground) contacts of all 4 channels have 1 common 0 V ground
potential.
Pos: 20.3 /Serie 750 (WAGO-I/O-SYST EM) /G erät eb esc hrei bung /Ei nlei tu ng/F unk tio n/Gal vani sc he Tr en nung Ei ng angss ig nal/ Gal vanis ch e Tr en nung Eingangssignal/Systemebene (12 Bit) @ 6\mod_1255353269263_21.docx @ 42550 @ @ 1
The input signal is electrically isolated and is transmitted with a resolution of
12 bits.
Pos: 20.4 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/L ED-A nzeig e/LE D F ehl er D ra htbr uch/ Ber eich sü ber- /unt erschr eitung @ 7\mod_1274363504640_21.docx @ 56902 @ @ 1
A red fault LED per channel indicates a wire break or that the signal is outside the
measuring range.
Pos: 20.5 /Serie 750 (WAGO-I/O-SYST EM)/ Ger äteb eschrei bung /Einl eitu ng/Ver sorg ung/An ordn ung unter Berüc ksich tigung der Lei stung skont akte bel iebig @ 3\mod_1233756233468_21.docx @ 27099 @ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node. An arrangement
in groups within the group of potentials is not necessary.
Pos: 20.6 /Serie 750 (WAGO-I/O-SYST EM) /G erät eb esc hrei bung /Ei nlei tu ng/V ers org ung/ Spa nnu ngs vers org ung aus S yste mspa nnu ng @ 5\mod_1247116433759_21. docx @ 36920 @ @ 1
Power to the internal electronics is supplied via internal data bus.
Pos: 20.7 /Serie 750 (WAGO-I/O-SYST EM)/ Gerät ebesc hrei bung/Ei nlei tung /Vers orgung /Vers orgu ng 24 V, 0 V üb er Leis tungs konta kte _ Weit erga be ohne ei gene Verwen dung @ 16\mod_1379319855936_21.doc x @ 131620 @ @ 1
The I/O module receives the 24 V voltage supply and the 0 V potential for the
field level from an upstream I/O module or from the fieldbus coupler/controller
via the power jumper contacts used as blade contacts. These potentials are passed
through without being used galvanically isolated to subsequent I/O modules.
Pos: 20.8 /Serie 750 (WAGO-I/O-SYST EM)/ Wicht ige Erl äuter unge n/Sich erhei ts- u nd sonstig e Hin weis e/Acht ung/A chtu ng: Ma ximaler Strom L eistung skon takt e 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 20.9 /Serie 750 (WAGO-I/O-SYST EM) /G erät eb esc hrei bung /Ei nlei tu ng/Ei ns atz ber eich /Ei nsatz ber eic h 7 50- xxxx alle Ko ppl er/Ei ns atz berei ch 75 0-xx xx alle Kop pler /Contr oller ohne Economy-Koppler @ 3\mod_1232541867468_21.docx @ 26525 @ @ 1
The I/O module 750-455 can be used with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750 (except for the economy types 750-320, -323, -324
and -327).
Pos: 20.1 0 /S eri e 7 50 (W AG O-I/O- SYST EM) /Ger äte beschr ei bung /Ei nleit ung/ I/ O-Bes chr eib ung /Allg em ein/ Ver weis a uf K apit el " Ans chl üss e" @ 8\mod_1276775378035_21.docx @ 57956 @ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos: 20 .11 / Seri e 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tung /I/ O-Be schr eib ung /All ge mein/ Ver wei s a uf K apit el " Ger ät e ansc hli eß en" > " Ansc hlus sb eispi el (e)" @ 5 \mod_1246015203281_21.docx @ 36298 @ @ 1
Connection examples are shown in section “Connecting Devices” > … >
“Connection Example(s)”.
Pos: 21 /Dokum entat ion all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
14 Device Description WAGO-I/O-SYSTEM 750
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 22 /Al l e Ser ien (Al lg emei ne M od ule)/Ü b ersc hrif te n für all e S eri en/G erä teb esc hreib ung /A nsic ht - Ü ber schr if t 2 @ 4\ mod_1240984217343_21.docx @ 31958 @ 2 @ 1
3.1 View
Pos: 23 /S eri e 7 50 ( WA GO-I/O- SYST EM)/ Gerät ebesc hrei bung/A nsic ht/Anal ogei nga ngskle mmen/ Ansic ht 750-0455 @ 15\mod_1370334937962_21.docx @ 121639 @ @ 1
Figure 1: View
Pos: 24 /S eri e 7 50 ( WA GO-I/ O-SYS TEM )/ Ger äteb esc hrei bu ng/A nsic ht /Ansi c ht Cag eCl a mp®_ Leg ende mi t LED s @ 15\ mod_1370867188922_21.docx @ 122225 @ @ 1
Table 4: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
---
2
Status LEDs
“Device Description” > “Display Elements”
3
Data contacts
“Device Description” > Connectors”
4
CAGE CLAMP
®
connectors
“Device Description” > Connectors”
5
Power jumper contacts
“Device Description” > Connectors”
6
Release tab
“Mounting” > “Inserting and Removing
Devices”
Pos: 25 /Dokum entat ion all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 15
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 26 /Al l e Ser ien (Al lg emei ne M od ule)/Ü b ersc hrif te n für all e S eri en/G erä tebeschreibung/Anschlüsse - Übers chri ft 2 @ 4\mod_1240984262656_21.docx @ 31961 @ 2 @ 1
3.2 Connectors
Pos: 27 /S eri e 7 50 ( WA GO-I/O- SYST EM) /Ger ät ebesc hrei bu ng/A nschl üss e/Da ten ko ntakt e/Kl em menbu s - Ü bersc hrift 3 @ 6\mod_1256294684083_21.doc x @ 43660 @ 3 @ 1
3.2.1 Data Contacts/Internal Bus
Pos: 28.1 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/A nschl üss e/Da ten kon takt e - F eldbu sko ppler /-c ontr oll er, A bbi ld ung und Besc hrei bu ng @ 3\mod_1231771259187_21.docx @ 26002 @ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the internal bus. It
is comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data Contacts
Pos: 28.2 /Serie 750 (WAGO-I/O-SYST EM)/ Wicht ige Erl äuter unge n/Sich erhei ts- u nd so nstig e H in weis e/ Acht ung /Ach tu ng: Buskl em men nic ht a uf Gol dfe der konta kt e leg en! @ 7 \mod_1266318463636_21.docx @ 50695 @ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos: 28.3 /Serie 750 (WAGO-I/O-SYST EM)/ Wicht ige Erl äuter unge n/Sich erhei ts- und sonstige Hinweise/Achtung/Achtung: ESD - Auf gut e E rdung der U mg ebu ng ac hte n! @ 7\ mod_1266318538667_21. docx @ 50708 @ @ 1
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos: 29 /Dokum entat ion all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
16 Device Description WAGO-I/O-SYSTEM 750
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 30 /S eri e 7 50 ( WA GO-I/O- SYST EM) /Ger ät ebesc hrei bu ng/A nschl üss e/L eist ung skont akt e/F eld versor gu ng - Üb ersc hrift 3 @ 6\ mod_1256294692864_21. docx @ 43664 @ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 31.1 /Serie 750 (WAGO-I/O-SYST EM)/ Wicht ige Erl äuter unge n/Sich erhei ts- u nd so nstig e H in weis e/ Vorsi cht/ V orsi cht: Ver letz ung sge fa hr dur c h sch arf kan tig e M esser ko nta kte! @ 6\ mod_1256193279401_21.docx @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos: 31.2 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/A nschl üsse/Leistungskontakte 2 LK (Messer/Leistungskontakte 2 LK (Messer/Feder) - Einlei tung @ 15 \mod_1371721641099_21.docx @ 123714 @ @ 1
The I/O module 750-455 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as blade contacts and those on the right side as spring
contacts.
Pos: 31.3 /Serie 750 (WAGO-I/O-SYST EM)/ Gerät ebesc hrei bung/A nschl üsse /Leist ungs kont akte 2 LK (Messer/Leistungskontakte 2 LK (Messer/Feder) - Abbil dung, einfac he Brei te - Stan dard @ 15 \mod_1367500700037_21.docx @ 118396 @ @ 1
Figure 3: Power Jumper Contacts
Pos: 31.4 /Serie 750 (WAGO-I/O-SYST EM) /G erät eb esc hrei bung /Ans chl üss e/L eist ung s kont akte 2 LK (M ess er/ Leis tung s konta kte 2 L K (M esser /F ed er) - Leg ende @ 15 \mod_1371721352500_21.docx @ 123710 @ @ 1
Table 5: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (U
v
) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (U
v
) for field supply
Pos: 31.5 /Serie 750 (WAGO-I/O-SYST EM)/ Wicht ige Erl äuter unge n/Sich erhei ts- u nd so nstig e H in weis e/ Acht ung /Ach tu ng: M a ximal er S tro m L eist ungs kon tak te 10 A @ 3\ mod_1226499143500_21.docx @ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 31.6 /Serie 750 (WAGO-I/O-SYST EM)/ Wicht ige Erl äuter unge n/Sich erhei ts- u nd sonstig e Hin weis e/Hinw eis/Hi nwei s: Pote ntialei ns peise klemme f ür Erde ei nset zen! ( keine LK für Erde) @ 3\mod_1226499037468_21.doc x @ 25023 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 17
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Use supply modules for ground (earth)!
The I/O module has no power jumper contacts for receiving and transmitting the
earth potential. Use a supply module when an earth potential is needed for the
subsequent I/O modules.
Pos: 32 /D o kume ntat ion all gemei n/ Glie der ungs elem ente /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
18 Device Description WAGO-I/O-SYSTEM 750
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 33 /S eri e 7 50 ( WA GO-I/O- SYST EM) /G erät eb eschr ei bung /Ans chl üss e/C AGE CL AMP- Ansc hlüs se - Ü b erschr if t 3 @ 6\ mod_1256296337770_21. docx @ 43674 @ 3 @ 1
3.2.3 CAGE CLAMP
®
Connectors
Pos: 34 /S eri e 7 50 ( WA GO-I/O- SYST EM) /G erät eb eschr ei bung /Ans chl üss e/A nal ogei nga ngs kle mm en/A nsc hlüs se 7 50- 0453, -0 455, - 0457 un d -0459 @ 15\mod_1370335893038_21.docx @ 121647 @ @ 1
Figure 4: CAGE CLAMP
®
Connectors
Table 6: Legend for Figure CAGE CLAMP
®
Connectors”
Channel
Designation
Connector
Function
1
AI 1
1
Analog input1: Signal
Common
(ground)
2
Analog input: Common (ground)
2
AI 2
5
Analog input 2: Signal
Common
(ground)
6
Analog input: Common (ground)
3
AI 3
3
Analog input 3: Signal
Common
(ground)
4
Analog input: Common (ground)
4
AI 4
7
Analog input 4: Signal
Common
(ground)
8
Analog input: Common (ground)
Pos: 35 /S eri e 7 50 ( WA GO-I/O- SYST EM)/ Wicht ige Erl äuter unge n/Sich erhei ts- und sonstige Hinweise/Hinweis/Hinweis: Geschi r mte Sig nall eit ung en verw end en! @ 7\ mod_1265723251019_21.docx @ 50140 @ @ 1
Use shielded signal lines!
Only use shielded signal lines for analog signals and I/O modules which are
equipped with shield clamps. Only then can you ensure that the accuracy and
interference immunity specified for the respective I/O module can be achieved
even in the presence of interference acting on the signal cable.
Pos: 36 /D o kume ntat ion all gemei n/ Glie der ungs elem ente /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750 Device Description 19
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 37 /Al l e Ser ien (Al lg emei ne M od ule)/Ü b ersc hrif te n für all e S eri en/G erä teb esc hreib ung /A nzei geel e ment e - Üb ersc hrift 2 @ 4\ mod_1240984390875_21.docx @ 31964 @ 2 @ 1
3.3 Display Elements
Pos: 38 /S eri e 7 50 ( WA GO-I/O- SYST EM)/ Gerät ebesc hrei bung/A nzeig eele mente /Anal ogei ngang sklem men/A nzeig eele mente 7 50-0455 @ 21\mod_1423226327425_21.docx @ 173708 @ @ 1
Figure 5: Display Elements
Table 7: Legend for Figure “Display Elements
Channel
Designation
LED
State
Function
1 Error AI 1 A
Off
Normal operation
Red
Broken wire, excess/underflow
of the admissible measuring range
2 Error AI 2 C
Off
Normal operation
Red
Broken wire, excess/underflow
of the admissible measuring range
3 Error AI 3 B
Off
Normal operation
Red
Broken wire, excess/underflow
of the admissible measuring range
4 Error AI 4 D
Off
Normal operation
Red
Broken wire, excess/underflow
of the admissible measuring range
Pos: 39 /Dokum entat ion all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
20 Device Description WAGO-I/O-SYSTEM 750
750-455 4AI 4-20mA S.E.
Manual
Version 1.2.0
Pos: 40 /Al l e Ser ien (Al lg emei ne M od ule)/Ü b ersc hrif te n für all e S eri en/G erä teb esc hreib ung /B edie nel eme nte - Ü b ersc hrif t 2 @ 4 \mod_1239191655456_21.docx @ 30439 @ 2 @ 1
3.4 Operating Elements
Pos: 41 /S eri e 7 50 ( WA GO-I/O- SYST EM) /G erät eb eschr ei bung /Be die nel emen te/ Bedi en elem ent e Bus kl em me 7 50- xxxx nic ht vor hande n @ 4\mod_1236322031125_21.docx @ 28063 @ @ 1
The I/O module 750-455 has no operating elements.
Pos: 42 /Dokum entat ion all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

WAGO I/O-SYSTEM 750 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI