Barrette Outdoor Living 73024433 Installation guide

1

EPN-5132

To register your product, please visit:

boerboelgatesystems.com

Read all instructions prior to installing product.

Refer to manufacturers safety instructions when operating any tools.

GardDog

™

Locking Latch with Handle

Installation Instructions

• English

........................................................

1

• Français

......................................................

7

• Español

.......................................................

13

2

Spacer

Catch Bracket

Catch

Templates

Keys

25mm Screws

16mm Screws

28mm Screw

Rear

Handle

Front

Handle

Gate

Safety Glasses

Level

Tape Measure

1/4" Drill Bit

1/2" Drill Bit

Phillips Driver Bit/Screwdriver

TOOLS NEEDED:

WARNING:

• Improper installation of this product can result in personal injury. Always wear safety goggles when

cutting, drilling and assembling the product.

• Incorrect installation may cause harm to the gate or individual.

• Not pool code approved.

NOTICE:

• DO NOT attempt to assemble the kit if parts are missing or damaged.

• DO NOT return the product to the store, for assistance or replacement parts call: 1-800-336-2383.

Component list:

QTY Description

1

Front Handle

1

Rear Handle

1

Catch

1

Catch Bracket

1

Spacer (For 1

1

⁄

1

⁄

1

2

⁄2⁄

" Post)

2

25mm Round Head

Machine Screws

3

16mm Phillips Self-Drilling Screws

1

28mm Phillips Machine Screw

3

Keys

1

Alignment Template - 1

1

⁄

1

⁄

1

2

⁄2⁄

" Gate

1

Alignment Template - 2" Gate

FOR 1.5" POST

1/2" DRILL

1/4" DRILL

1/2" DRILL

1/4" DRILL

1/4" DRILL 1/4" DRILL

FOR 2" POST

1/2" DRILL

1/4" DRILL

1/2" DRILL

1/4" DRILL

1/4" DRILL 1/4" DRILL

3

Fig. 1

Fig. 2

Mounting the Upright Handles:

a.) Once hinges are installed and gate is aligned, place

the alignment template on the gate upright at the

desired height.

NOTE:

Use the 1

1

⁄

1

⁄

1

2

⁄2⁄

" template for 1

1

⁄

1

⁄

1

2

⁄2⁄

" gate uprights,

or 2" template for 2" gate uprights.

Ensure the two solid lines of the template are

positioned at the outer edges of the gate upright

(Fig. 1).

b.) Pre-drill two corner holes using a

1

⁄

1

⁄

1

4

⁄4⁄

" drill bit and

pre-drill one center hole using a

1

⁄

1

⁄

1

2

⁄2⁄

" drill bit. Repeat

on opposite side of upright (Fig. 2).

c.) Remove and discard templates.

d.) Insert the three prongs of the front handle through

the three pre-drilled holes on the front side of the

upright (Fig. 3).

NOTE:

If using a 1

1

⁄

1

⁄

1

2

⁄2⁄

" upright, you will use the included

spacer. 2" uprights do not require the spacer.

The remainder of this manual shows the

installation using the spacer.

e.) Align the spacer on the rear face of the upright

though the three prongs of the front handle (Fig. 4).

f.) Install the rear handle by guiding the  at bar of

the front handle into the slotted groove of the rear

handle (Fig. 5).

1

Template

Gate Upright

1/4"

1/2"

1/4"

Solid Lines

Front

Fig. 3

Fig. 4

Fig. 5

Front

Handle

Front

Handle

3 Prongs

Front

of Uprightof Upright

Close-Up of Close-Up of

Rear Handle

Flat Bar

Spacer not Spacer not

shown for detail

4

(Step 1 Continued)

g.) Using two 25mm round head Phillips machine

screws, secure rear handle to the two threaded

corner prongs of the front handle (Fig. 6).

h.) Snap on rear handle cover (Fig. 7)

Fig. 6

Fig. 7

Fig. 9

Fig. 11

25mm

Screws

Rear

Handle

Mounting The Catch To The Post

a.) Slide the catch onto the catch bracket (Fig. 8).

b.) Align the catch at the correct height along post to

engage with the front handle striker (Fig. 9).

c.) While holding the catch bracket in place, mark the

center of the two slotted holes on the inside of the

post (Fig. 10).

d.) Slide the catch off of the bracket and mark the

center of the slotted hole on the front of the post

(Fig. 11).

2

Fig. 8

CatchCatch

Bracket

Fig. 10

Inside

of Postof Post

5

(Step 2 Continued)

e.) Pre-drill holes and secure catch bracket with three

16mm Phillips self-drilling screws (Fig. 12).

f.) Slide the catch onto the bracket and position,

ensuring the proper gap to engage the striker. The

gap between the catch and the front handle base

should be no larger than

1

⁄

1

⁄

1

8

⁄8⁄

" (Fig. 13).

g.) Once you align the catch on the bracket, secure

its position with one 28mm Phillips machine screw.

Rotate the screw clockwise to decrease the gap, or

counter-clockwise to increase the gap (Fig. 14).

Adjusting The Handles

The handles are able to be positioned in a vertical or

horizontal orientation depending on your preference.

a.) Loosen the small screw under the shaft of the

handle (Fig. 15).

b.) Position the handle to desired orientation and

tighten the screw (Fig. 16).

3

Inside

of Post

Fig. 12

Front

ViewView

Max 1/8"

Fig. 13

Fig. 14

Fig. 15

Fig. 16

28mm

screw

Remove

ScrewScrew

ReplaceReplace

Screw

ScrewScrew

6

Subject to the conditions and limitations set out below, Barrette Outdoor Living

warrants that for so long as the original purchaser of a product manufactured by

Barrette Outdoor Living owns that Boerboel Manual Hardware (the Product) it will be

free from all defects due to faulty design, materials or workmanship.

If a defect in the Product appears the purchaser must advise Barrette Outdoor Living

within 14 days of discovering the defect and return the defective item, comprising

either the Product or a defective component of the Product (the ltem), to

Barrette Outdoor Living, freight prepaid, together with proof of purchase whereupon

Barrette Outdoor Living will, at its option and cost, repair or replace the defective

ltem with the same or an equivalent Product or component. Barrette Outdoor Living

will not be liable for labor or any other costs associated with the dismantling, return

or reassembly of the Product or any frame or structure to which it is af xed.

This warranty does not apply in respect of defects due to or arising from:

(a) normal wear and tear;

(b) the failure to follow any procedures speci ed or recommended by

Barrette Outdoor Living for the installation, operation and maintenance of

the Product;

(c) any act or circumstance beyond Barrette Outdoor Livings control including

tampering, unauthorized repairs, misuse, abnormal use, abuse, accident,

damage after delivery to the consumer, damage caused by events beyond

human control including but not limited to damage caused by animals or

natural events, surface tarnishing and/or damage to components caused by

corrosion or other environmental conditions;

(d) any defect of or in any framework or material supporting the Product; or

(e) the faulty workmanship of any person other than Barrette Outdoor Living,

including the installer of the Product.

This warranty is personal to the original purchaser of the Product or to the  rst

consumer where the Product has been installed by a contractor for the bene t

of the consumer and may not be assigned without Barrette Outdoor Living’s prior

written consent.

This warranty gives you speci c legal rights which are in addition to, and do not

replace, other rights and remedies you may have available to you by law and which

may vary from state to state.

Except as expressly granted in this warranty or where to do so would contravene

a statute:

(a) all other warranties, conditions and representations, whether express or

implied by general law, statute or custom, in relation to the Product and its

quality,  tness for purpose and suitability are expressly excluded; and

(b) Barrette Outdoor Living’s liability is excluded for all other loss, damage or

injury of any kind whatsoever (including any direct, indirect or consequential

loss or damage, loss of pro ts or loss of opportunity) arising in connection

with the Product, or the supply, condition or use of the Product, including as

a result of any negligence, misrepresentation, or other default on the part of

Barrette Outdoor Living, its of cers, employees, or contractors or otherwise.

For any speci c questions about the Barrette Outdoor Living Warranty or to make a

warranty claim please contact Barrette Outdoor Living by visiting our website

www.boerboelgatesystems.com, emailing or calling 1-800-336-2383.

To begin your warranty coverage and register your Boerboel Manual Hardware

product visit: www.boerboelgatesystems.com. Retain manual and your dated sales

slip for future reference or warranty claims.

Limited Lifetime Warranty

Page is loading ...

BARRETTE OUTDOOR LIVING

7830 FREEWAY CIRCLE

MIDDLEBURG HEIGHTS, OHIO 44130

TEL: (800) 336-2383

WWW.BOERBOELGATESYSTEMS.COM

Barrette Outdoor Living 73024433 Installation guide

Barrette Outdoor Living 73024433 Installation guide

in other languages

Related papers

Other documents