Boerboel 73002181 Installation guide

1

EPN-5065

To register your product, please visit:

boerboelgatesystems.com

Read all instructions prior to installing product.

Refer to manufacturers safety instructions when operating any tools.

Standard Strap Hinge

Installation Instructions

• English

........................................................

1

• Français

......................................................

7

• Español

.......................................................

13

2

Safety Glasses

Level

Tape Measure

Drill

Pencil

3/32" & 1/4" Drill Bits

10 mm Wrench

Phillips Screwdriver

TOOLS NEEDED:

BEFORE YOU BEGIN:

Vinyl gate posts require an internal support

system for weight-bearing purposes and

therefore wooden inserts or a post stiffener

is required. Post stiffener needs to be

purchased separately.

WARNING:

• Improper installation of this product can result in personal injury. Always wear safety goggles when

cutting, drilling and assembling the product.

• Incorrect installation may cause harm to the gate or individual.

• Not pool code approved.

NOTICE:

• DO NOT attempt to assemble the kit if parts are missing or damaged.

• DO NOT return the product to the store, for assistance or replacement parts call: 1-800-336-2383.

Top View of Routed Post

Fence

Purchased

Metal Stiffener

Component list:

QTY Description

1

Standard Strap Hinge

1

Back Plate

9

1

⁄

1

⁄

1

4

⁄4⁄

" Stainless Steel Phillips Self-Driving Screws

3

1

⁄

1

⁄

1

2

⁄2⁄

" Stainless Steel Lag Screws

3

60 mm Hex Bolts

3

Thin Hex Nuts

3

Nylon Washers

3

Acorn Nuts

Back Plate

Standard Strap Hinge

60 mm Hex Bolts

Lag Screws

Thin Hex Nuts

Nylon Washers

Acorn Nuts

1

⁄

1

⁄

1

4

⁄4⁄

" Stainless Steel

Phillips Self-Driving Screws

3

Determine

location and gate

opening before

installing fence.

Fig. 1

Determine Gate Opening:

Gate opening is determined by width of gate plus

clearance for the hinge (5/8") plus clearance for a

latch/drop rod (Fig. 1).

1

2

Installing the Hinge:

NOTE:

- Gate can be adjusted to swing up to

160 degrees.

a.) Position hinge swing arm on the rail and mark

pilot holes through screw holes, as shown, with a

minimum spacing of 32" between each hinge (Fig. 2).

b.) Drill pilot holes:

- If you are installing the hinge on a hollow

gate rail (such as vinyl), use a

1

⁄

1

⁄

1

4

⁄4⁄

" bit

and drill all the way through the gate rail, so that

bit comes through the opposite side. Be sure to

hold the drill straight and level so that the back

plate will be properly aligned when mounted (Fig. 3).

- If you are installing the hinge on a solid gate

rail (such as wood), use a

3

⁄

3

⁄

3

32

⁄32⁄

" bit. Pilot

holes should NOT be drilled all the way through

the solid gate rail, as the back plate is not

required.

c.) Secure Hinge to Gate Rail:

- When installing hinges on a hollow gate

rail (such as vinyl), install the back plate

on the opposite side of the gate rail and

secure with the appropriately sized bolts and

fasteners, speci ed in the table below. The

included nylon spacer may be required

to  ll void space (Fig. 4).

- When installing hinges on a solid gate rail (such

as wood), secure both hinges to the gate using

three 1

1

⁄

1

⁄

1

2

⁄2⁄

" stainless steel lag screws. The back

plate is not required.

- Depending on which application you are

using, tighten the phillips screws with a phillips

screwdriver or the bolts with a 10 mm wrench.

Rail

Width

Bolt Size Fastener

1.5"

60 mm

Locking Nut With Spacer

1.75"

60 mm

Acorn Nut With Spacer

2"

60 mm

Acorn Nut

Mark pilot holes

For vinyl fence, drill pilot holes

through rail

Fig. 2

Fig. 3

Front

Back

Fig. 4

4

3

4

Mount Gate to Post:

NOTE:

Both gate posts must be plumb prior to gate

installation.

a.) Position gate at desired height on post. Horizontal

rails on gate should be even with horizontal rails on

fence, if applicable.

b.) Measure space between ground and bottom of

gate and cut two wood spacer blocks to this

height. Rest gate on the spacer blocks and hold it

level/plumb to the gate post (Fig. 6).

c.) While holding the post plate of the hinge  rmly

against post, mark pilot holes on the post, through

the four screw holes in the front of the post plate

(Fig. 7).

d.) Remove gate and drill four

3

⁄

3

⁄

3

32

⁄32⁄

" pilot holes in post.

e.) Re-position gate on post and secure hinges with

four 1

1

⁄

1

⁄

1

4

⁄4⁄

" phillips screws per hinge. Do not tighten

the screws all the way at this point (Fig. 7).

f.) Open gate and drill four

3

⁄

3

⁄

3

32

⁄32⁄

" pilot holes through the

four screw holes in the sides of the post plate (Fig. 8).

g.) Secure with four 1

1

⁄

1

⁄

1

2

⁄2⁄

" stainless steel lag screws per

hinge. Do not tighten the screws all the way at this

point (Fig. 8.)

Adjust Gate:

NOTE:

The hinge has a unique feature to adjust your gate

forward or backward, in relation to the post.

a.) Once the gate is set in the desired position, drill a

3

⁄

3

⁄

3

32

⁄32⁄

" pilot hole in the center hole on the post plate.

b.) Secure with one 1

1

⁄

1

⁄

1

2

⁄2⁄

" stainless steel lag screw and

tighten with a 10 mm wrench (Fig. 9).

c.) Tighten all eight lag screws from steps 3e and 3g

above with a 10 mm wrench (Fig. 9).

Wood Spacer Blocks

Fig. 6

Fig. 7

Fig. 8

Fig. 9

5

To Reconﬁ gure for Right-Side Mounting:

a.) Remove the plastic cover from the hinge pin and

pull the pin out of the hinge (Fig. 10).

b.) Flip the hinge assembly over so that the rounded

notch in the post plate is facing to the right and so

that the Boerboel® logo on the swing arm faces

front (Fig. 11).

c.) Replace the hinge pin through the top (Fig. 12).

d.) Replace and secure the bottom of the hinge pin

with the plastic cover (Fig. 12).

Plastic cover

Hinge Pin

Fig. 10

Plastic cover

Hinge Pin

Fig. 12

Fig. 11

6

Subject to the conditions and limitations set out below, Barrette Outdoor Living

warrants that for so long as the original purchaser of a product manufactured by

Barrette Outdoor Living owns that Boerboel Manual Hardware (the Product) it will be

free from all defects due to faulty design, materials or workmanship.

If a defect in the Product appears the purchaser must advise Barrette Outdoor Living

within 14 days of discovering the defect and return the defective item, comprising

either the Product or a defective component of the Product (the ltem), to

Barrette Outdoor Living, freight prepaid, together with proof of purchase whereupon

Barrette Outdoor Living will, at its option and cost, repair or replace the defective

ltem with the same or an equivalent Product or component. Barrette Outdoor Living

will not be liable for labor or any other costs associated with the dismantling, return

or reassembly of the Product or any frame or structure to which it is af xed.

This warranty does not apply in respect of defects due to or arising from:

(a) normal wear and tear;

(b) the failure to follow any procedures speci ed or recommended by

Barrette Outdoor Living for the installation, operation and maintenance of

the Product;

(c) any act or circumstance beyond Barrette Outdoor Livings control including

tampering, unauthorized repairs, misuse, abnormal use, abuse, accident,

damage after delivery to the consumer, damage caused by events beyond

human control including but not limited to damage caused by animals or

natural events, surface tarnishing and/or damage to components caused by

corrosion or other environmental conditions;

(d) any defect of or in any framework or material supporting the Product; or

(e) the faulty workmanship of any person other than Barrette Outdoor Living,

including the installer of the Product.

This warranty is personal to the original purchaser of the Product or to the  rst

consumer where the Product has been installed by a contractor for the bene t

of the consumer and may not be assigned without Barrette Outdoor Living’s prior

written consent.

This warranty gives you speci c legal rights which are in addition to, and do not

replace, other rights and remedies you may have available to you by law and which

may vary from state to state.

Except as expressly granted in this warranty or where to do so would contravene

a statute:

(a) all other warranties, conditions and representations, whether express or

implied by general law, statute or custom, in relation to the Product and its

quality,  tness for purpose and suitability are expressly excluded; and

(b) Barrette Outdoor Living’s liability is excluded for all other loss, damage or

injury of any kind whatsoever (including any direct, indirect or consequential

loss or damage, loss of pro ts or loss of opportunity) arising in connection

with the Product, or the supply, condition or use of the Product, including as

a result of any negligence, misrepresentation, or other default on the part of

Barrette Outdoor Living, its of cers, employees, or contractors or otherwise.

For any speci c questions about the Barrette Outdoor Living Warranty or to make a

warranty claim please contact Barrette Outdoor Living by visiting our website

www.boerboelgatesystems.com, emailing or calling 1-800-336-2383.

To begin your warranty coverage and register your Boerboel Manual Hardware

product visit: www.boerboelgatesystems.com. Retain manual and your dated sales

slip for future reference or warranty claims.

Limited Lifetime Warranty

Page is loading ...

BARRETTE OUTDOOR LIVING

7830 FREEWAY CIRCLE

MIDDLEBURG HEIGHTS, OHIO 44130

TEL: (800) 336-2383

WWW.BOERBOELGATESYSTEMS.COM

Boerboel 73002181 Installation guide

This manual is also suitable for

Boerboel 73002181 Installation guide

in other languages

Related papers

Other documents