American Standard T555.521.002 Installation guide

American Standard
Brand
American Standard
Model
T555.521.002
Category
Sanitary ware
Type
Installation guide
TOWN SQUARE
®
Recommended Tools
Adjustable Wrench Channel LocksFlat Blade Screwdriver Plumbers' Putty or CaulkingPhillips Screwdriver
1-5/8" TO 3-1/4"
FINISHED WALL
BOTTOM OF
TUB
74" FOR
HEAD CLEARANCE
2" REF.
18"
OPTIONAL
1/2" I.P.S.
1
7-5/8"
4-7/8" REF.
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
65'' AND 78''
8" REF.
8-1/2" REF.
4"
TOP OF
TUB RIM
1-3/4" REF.
1/2" COPPER
SEE VALVE INSTRUCTIONS FOR
INSTALLATION INFORMATION
7-1/4" REF.
Certified to comply with ANSI A112.18.1
T555.52X
Installation
Instructions
ROUGHING-IN DIMENSIONS
■ To assure proper positioning in relation to
wall, note roughing-in dimensions.
PRESSURE BALANCING BATH
AND SHOWER TRIM KIT
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
M965112 REV.1.4 (8/15)
FLOWISE 3-FUNCTION
SHOWERHEAD
1
31
INSTALL TRIM
CAUTION: Protect finish on SHOWER ARM,
SHOWER HEAD and TUB SPOUT when installing.
2
A
6
7
7A
3
1
4
9
5
5
8
HEX WRENCH
When finished tiling the wall, remove PLASTER GUARD (A)
and turn off water supply.
Push CAP (1) over VALVE CARTRIDGE (2).
Mount ESCUTCHEON (3) to valve body with SCREWS (4).
OPTIONAL: Push DECORATIVE SCREW COVER (9)
(purchased separately) onto CAP (1) flush against ESCUTCHEON (3).
Remove PIPE CAPS (5) from shower pipe and tub filler pipe.
Install SHOWER ARM (6), SHOWER HEAD (7 or 7A) by
threading onto pipe nipple using teflon tape or pipe sealant.
Install SLIP-ON TUB SPOUT (8). Tighten with
HEX WRENCH supplied.
1-3/4" REF.
3
M965112 REV.1.4 (8/15)
Align and install HANDLE (1) onto valve stem.
Tighten SET SCREW (2) using 2.5mm Hex
Wrench supplied. Push in index (4).
Check proper operation of HANDLE (1).
Turn on water supply on and test installed fitting.
Operate valve and DIVERTER SPOUT (3).
HEX WRENCH
2
4
VALVE STEM
"B"
"B"
2
ADJUST HOT LIMIT STOP
By restricting handle rotation and limiting the amount
of hot water allowed to mix with the cold, the HOT
LIMIT SAFETY STOP reduces risk of accidental scalding.
To set the maximum hot water temperature of your
faucets, all you need to do is adjust
the setting on the HOT LIMIT SAFETY STOP.
Use a flat blade screwdriver or your fingers
to pull up and rotate red HOT LIMIT SAFETY
STOP (1). Follow Step "A" or "B" to adjust
min./max. discharge temperature. "0" being
the hottest to "7" the coldest temperature
setting. Factory set at "0".
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RING
FORWARD AND ROTATE
COUNTER-CLOCKWISE
ONE CLICK
PRY RED RING
FORWARD AND
ROTATE CLOCKWISE
"A"
"A"
ADJUSTMENT WHEN
WATER IS TOO HOT
ADJUSTMENT WHEN
WATER IS TOO COLD
"RED RING"- HOT
LIMIT SAFETY STOP
TEMPERATURE
SETTING
NUMBERS
1
0
1
2
3
4
5
6
INSTALL HANDLE and TEST FITTING
7
8
4
Remove CARTRIDGE (7) by removing CARTRIDGE
SCREWS (8). Remove three SCREWS (9) from
FIXATION RING (10) and pull out PRESSURE
BALANCING (16) unit.
Clean SEALS (11) on base of CARTRIDGE (7).
Check base of PRESSURE BALANCING UNIT (12)
and clean O-RINGS (13). Remove CAPS (14)
and check O-RINGS on inside of CAPS (14) for
debris. Clean inside sealing surfaces of VALVE
BODY (15). Re-assemble PRESSURE BALANCING
UNIT (12) and CARTRIDGE (7). Tighten
all screws.
VALVE LEAKS WHEN SHUT OFF
5
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
M965112 REV.1.4 (8/15)
SERVICE
CARTRIDGE
INLETS
7
6
HEX WRENCH
3
1
4
5
2
Remove PRESSURE BALANCE UNIT (12).
Remove CAPS (14) and clean valve thoroughly.
Examine balancing unit and check condition of O-ring on end of piston. Piston should move back and forth. Order Repair
Part M952100-0070A if balancing unit is defective.
Replace CAPS (14) and install PRESSURE BALANCE UNIT (12). Make sure inlets line up with two holes in bottom of
casting. Top flange should butt-up against top of casting.
UNABLE TO MAINTAIN CONSTANT TEMPERATURE
9
14
13
15
12
10
11
Turn off hot and cold water supplies.
Loosen HANDLE SET SCREW (1) and pull of
HANDLE (2).
If installed, pull off DECORATIVE SCREW COVER (3).
Remove two SCREWS (4) holding ESCUTCHEON (5)
and remove ESCUTCHEON (5).
Remove CAP (6).
TO GAIN ACCESS TO VALVE FOR SERVICING
M953570-YYY0A
SHOWER HEAD
(T555.521/T555.522)
A901428-YYY0A
SHOWER ARM
TOWN SQUARE
®
T555.52X
MODEL NUMBER
M964001-YYY0A
LEVER HANDLE KIT
030126-0070A
INDEX AND SCREW KIT
CHROME
SATIN NICKEL
OIL RUBBED BRONZE
002
295
224
Replace the "YYY" with
appropriate finish code
M964856-YYY0A
ESCUTCHEON KIT
WITH SCREWS
M950291-YYY0A
DIVERTER SPOUT
(SLIP-ON)
1660.813-YYY0A
3-FUNCTION FLOWISE
SHOWER HEAD
(T555.527/T555.528)
BATH/SHOWER
TRIM KIT
M965112 REV.1.4 (8/15)
078016-YYY0A
ESCUTCHEON SCREWS
M962055-YYY0A
OPTIONAL DECORATIVE
SCREW COVER
M907050-YYY0A
CARTRIDGE COVER
M964447-YYY0A
DIVERTER KIT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

American Standard T555.521.002 Installation guide

American Standard
Brand
American Standard
Model
T555.521.002
Category
Sanitary ware
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents