Avocent SwitchView DVI SH Series Quick Installation Manual

Avocent
Brand
Avocent
Model
SwitchView DVI SH Series
Category
KVM switches
Type
Quick Installation Manual

This manual is also suitable for

The following instructions will help you
install your SwitchView DVI switch.
Should you require further assistance
please contact Avocent Technical Support.
NOTE: The default setting of the
SwitchView DVI switch is appropriate for
most systems. You do not need to configure
the switch before installation. You should
turn off your computers before beginning
installation.
1
Connecting power
Connect AC power to the SwitchView DVI
Dual-Head (DH) or Single-Head (SH) switch.
CAUTION: When connecting a monitor to the
local port, turn on power to your switch before
booting up the targets.
2
Connecting your peripherals
Connect your keyboard, monitor(s) and mouse
into the console connectors on the rear of your
SwitchView DVI switch.
3
Connecting your computers
Connect each of your computers to the
SwitchView DVI switch using the DVI-I video
cable, USB cable (Type A to Type B) and audio
and mic cables provided.
4
Turning on your system
Turn on the connected computers. The front
panel LEDs indicate PC port status.
For KVM connections:
• LEDnotlit=Targetdeviceisnotturnedon
or selected.
• Green=Targetdeviceisturnedon,butnot
selected.
• Amber=Targetdeviceisselected.
For USB connections:
• LEDnotlit=Targetdevicenotselected.
• On(constant)=Targetdeviceisselected.
NOTE: The SwitchView DVI switch supports
digital video resolutions up to 2560 x
1600 @ 60 Hz and also supports analog
resolutions up to 1600 x 1200 @ 60Hz.
Upgrading your firmware (optional)
The SwitchView DVI switch series allows you
to optionally upgrade your system with current
firmware files when available from Avocent.
Connecting the serial port
Plug the DB-9 to RJ-45 adaptor (included) into
the console serial port. Connect one end of the
RJ-45 cable into the adaptor and connect the
other end into the RJ-45 port on the rear panel
of your SwitchView switch.
QUICK INSTALLATION GUIDE SwitchView® DVI DH and DVI SH Switch Series
To Contact Avocent Technical Support: Visit www.avocent.com 590-918-501B
Avocent, the Avocent logo, and SwitchView are registered trademarks of Avocent Corporation or its affiliates in the U.S. and other countries. All other marks are the property of their respective owners. ©2009 Avocent Corporation.
2
3
4
1
SwitchView DVI DH switch shown
5
5
QUICK INSTALLATION GUIDE SwitchView DVI DH and DVI SH Switch Series
To Contact Avocent Technical Support: Visit www.avocent.com 590-918-501B
Avocent, the Avocent logo and SwitchView are registered trademarks of Avocent Corporation or its affiliates in the U.S. and other countries. All other marks are the property of their respective owners. ©2009 Avocent Corporation.
To configure the serial port:
Set the terminal program as follows to configure
your serial port for a firmware upgrade:
Speed (baud) - 115200
Data bits - 8
Stop bits - 1
Parity - none
Flow control - none
To upgrade your firmware:
a.Gotowww.avocent.com/updatesand
download the appropriate firmware file.
b. Select the Transfer pull-down menu
located on the toolbar on the top of your
screen.
c. Ensure that Protocol Xmodem is
selected.
d. Select Send File.
e. Browse your computer for the
downloaded firmware file.
f.Openthermwareupgradeleand
select Send.
g. After the upgrade is complete, press the
spacebar to reset your KVM switch.
h. Verify the upgrade version showing on
your screen.
Operating the SwitchView DVI switch
You can control the SwitchView DVI switch for
PCandUSBhubportcontrol,aswellasaudio/
mic channel selection, scan and scan interval
time by using front panel push-buttons or a
hotkey sequence.
Complete instructions for both hotkey
commands and front panel button usage can be
found on the following page.
Hotkey sequence
Hotkey commands allow you to access and
control certain features of your SwitchView
switch via the local keyboard. The default
preceding hotkey sequence is Ctrl + Ctrl.
Front panel buttons
The front panel push-buttons provide direct
control over KVM channel switching by pressing
the PC button for PC port switching. If binding
isenabledbetweenPC/USBhubportcontrol
andaudio/micswitching,theywilljointlybe
selected simultaneously.
6
QUICK INSTALLATION GUIDE SwitchView DVI DH and DVI SH Switch Series
To Contact Avocent Technical Support: Visit www.avocent.com 590-918-501B
Avocent, the Avocent logo, and SwitchView are registered trademarks of Avocent Corporation or its affiliates in the U.S. and other countries. All other marks are the property of their respective owners. ©2009 Avocent Corporation.
Hotkey and front panel button reference sheet
NOTE: ACT keys are your defined activation keys. As a result, ACT1 + ACT2 means you should press your activation key twice in sequence. The default
activation key is Ctrl, meaning Ctrl + Ctrl is the default preceeding sequence for all hotkey commands.
COMMAND HOTKEYS FRONT PANEL BUTTONS & NOTES DESCRIPTION
Define Hotkey Preceding Sequence ACT1 + ACT2 + H + (y) + Enter
y=Ctrl(1),Alt(2),Shift(3),PrntScrn(4)
N/A Select the hotkey preceding sequence from
the following: Ctrl, Alt, Shift or PrntScrn.
Select PC Channel
(JointselectPCport,hubport,audio/mic
control if binding enabled)
ACT1 + ACT2 + (x)
+ Enter
x=1-4forPCchannelnumber
Press the corresponding button to select the
active PC channel.
SelecttheactivePCchannel(jointselectPC
port/hubportcontrol/audioandmicifbinding
is enabled).
Select Hub Port Control
ACT1 + ACT2 + Fx + Enter
x=1-4
Press the corresponding button to select the
specicPC/USBhubportcontrolifPCport/
hub port control binding is enabled.
Select the PC channel that controls all USB
hub ports. This command automatically
disablesPC/USBhubportbinding.
Move USB Hub Port ACT1 + ACT2 + F9 + Enter N/A Moves USB hub ports to currently selected
KVM session channel.
Disable USB Hub Port
(To enable the USB port hub, use the USB
hub port control to select the desired port.)
ACT1 + ACT2 + F10 + Enter N/A Disables USB hub ports.
Enable or Disable PC/USB Port Binding ACT1 + ACT2 + B + (x) + Enter x=+(Pluskey)
x=-(Minuskey)
Enables (Plus key) or disables (Minus key)
PC/USBportbinding.
Select PC for Local Port Audio ACT1 + ACT2 + T + (x) + Enter
x=1-4
x=+(Pluskey)Enablesaudiobinding
x=-(Minuskey)Disablesaudiobinding
Selects active target PC for local port
signals. This command automatically disables
audio signal binding.
Next Lower PC Channel
(PCportcontroljointlycontrolsPCandhub
port controls if binding is enabled. Using the
USB hub port control separately automatically
unbinds the USB hub session.)
ACT1 + ACT2 + L + Down or
Left Arrow + Enter
N/A SelectthenextlowerPC(jointselectPCport
and hub port control if binding is enabled).
Next Higher PC Channel
(PCportcontroljointlycontrolsPCandhub
port controls if binding is enabled. Using the
USB hub port control separately automatically
unbinds the USB hub session.)
ACT1 + ACT2 + L + Up or
Right Arrow + Enter
Press the PC button to toggle the PC
channel.
SelectthenexthigherPC(jointselect
PC port and hub port control if binding is
enabled).
Previous PC Channel ACT1 + ACT2 + L + Backspace + Enter N/A Toggle between previous channel and
current channel.
Scan Interval Time ACT1 + ACT2 + S + (n) + Enter n=2-60(Seconds) Setsintervalscantime.Defaultis30secs.
Interval Scan Begin ACT1+ACT2+S+G+Enter N/A Starts interval scan function. This command
automaticallydisablesPC/USBhubport
binding.
Stop Scan ACT1 + ACT2 + S + H + Enter N/A Terminate scan activity.
Enable/Disable Mouse Movement to
Halt Scanning
ACT1 + ACT2 + S + M + (x) + Enter x=+(Pluskey)
x=-(Minuskey)
Enables (Plus key) mouse movement to halt
scanning or disables (Minus key) mouse
movement to halt scanning.
Enable/Disable Double-Click Scan
Function
ACT1 + ACT2 + S + S + (x) + Enter x=+(Pluskey)
x=-(Minuskey)
Enables (Plus key) double-clicking the mouse
wheel button to scan up to the next powered
target or disables (Minus key) this operation.
590-918-501B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Avocent SwitchView DVI SH Series Quick Installation Manual

Avocent
Brand
Avocent
Model
SwitchView DVI SH Series
Category
KVM switches
Type
Quick Installation Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents