2. Computers & electronics
  3. Computer components
  4. Chassis components
  5. Racks
  6. Rack accessories
  7. Emerson
  8. Avocent Universal Management Gateway
Avocent Universal Management Gateway

Emerson Avocent Universal Management Gateway Quick Installation Guide

  • Hello! I am an AI chatbot trained to assist you with the Emerson Avocent Universal Management Gateway Quick Installation Guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I attach the brackets to the UMG appliance?
    How do I install the slide-rail brackets to the rack?
    How do I install the appliance in the rack?
    What is the wall mounting bracket kit for the UMG appliance?
    How do I mount the brackets to a plywood wall?
    How do I attach the appliance to the brackets for wall mounting?
Rack Mounting an Appliance
To Contact Avocent Technical Support: Visit www.avocent.com 590-1079-501B
Emerson, Emerson Network Power and the Emerson Network Power logo are trademarks or registered trademarks of Emerson Electric Co. Avocent and the Avocent logo are registered trademarks of Avocent Corporation or its
affiliates in the U.S. and other countries. This document may contain confidential and/or proprietary information of Avocent Corporation, and its receipt or possession does not convey any right to reproduce, disclose its contents,
or to manufacture or sell anything that it may describe. Reproduction, disclosure, or use without specific authorization from Avocent Corporation is strictly prohibited. © 2012 Avocent Corporation. All rights reserved.
1
UMG APPLIANCE MOUNTING BRACKET
Quick Installation Guide
The following instructions will help you
rack mount your Universal Management
Gateway (UMG) appliance. Should you
require further assistance, please contact
Avocent Technical Support.
1
Attaching the brackets to the
appliance
Remove the four black screws from
each side of the Universal Management
Gateway appliance. Position each
bracket so it is not covering the side
vents of the appliance. Secure the
mounting brackets to the appliance using
the eight chrome screws supplied with
the appliance.
2
Installing the slide-rail brackets
to the rack
Loosely attach the two slide-rail brackets
to the front of the rack using the
appropriate screws for your rack.
3
Installing the appliance in the rack
From the rear of the rack, slide the
appliance into the same U position where
the slide rails are mounted. Ensure that
both slide rails are securely inserted into
the appliance bracket. Tighten the rack
screws for both the appliance bracket
and the slide rails.
2
3
1
RACK
Back
Front
RACK
Back
Front
To Contact Avocent Technical Support: Visit www.avocent.com 590-1079-501B
Emerson, Emerson Network Power and the Emerson Network Power logo are trademarks or registered trademarks of Emerson Electric Co. Avocent and the Avocent logo are registered trademarks of Avocent Corporation or its
affiliates in the U.S. and other countries. This document may contain confidential and/or proprietary information of Avocent Corporation, and its receipt or possession does not convey any right to reproduce, disclose its contents,
or to manufacture or sell anything that it may describe. Reproduction, disclosure, or use without specific authorization from Avocent Corporation is strictly prohibited. © 2012 Avocent Corporation. All rights reserved.
2
UMG APPLIANCE MOUNTING BRACKET
Quick Installation Guide
The following instructions will help you
wall mount your Universal Management
Gateway (UMG) appliance.
Should you require further assistance,
please contact Avocent Technical Support.
NOTE: The wall mounting kit is
optional and is not included with the
UMG appliance; it must be purchased
separately. For details on how to purchase
the wall mounting kit, contact your
Avocent representative.
Overview
Your optional wall mounting bracket kit
contains two brackets. Either may be used
as a left or right bracket. In addition, the
brackets may be attached with the slots
facing up or down.
Mount the brackets
so that the front face of the Universal
Management Gateway appliance is facing
sideways and not toward the floor or ceiling.
Mounting the brackets to a
plywood wall
Using the slots on the bracket or the
supplied template as a guide, mark the
holes on the wall where the brackets are
to be fastened. A minimum of two holes
for each bracket should be marked. Use
a 3/16-inch drill bit to drill guide holes
at the marked positions. Using 1/4 inch
by 1 inch hex lag screws (not included
with the wall mounting kit), secure each
bracket to the plywood wall, using at
least two screws for each bracket.
Attaching the appliance to the
brackets
Remove the two middle truss-head
screws from each side of the appliance.
It is important to remove only the middle
two screws allowing the cover of the
appliance to stay secured. Align the
holes in the appliance with the holes in
the mounted-brackets and, using
the thumb screws provided with the
wall-mounting kit, secure the appliance
to the brackets with the slots facing up
or down, as illustrated.
2
1
Front
1
2
2
1
Wall Mounting an Appliance
/