Vista VIP2 VK2-540VRD User manual

VK2-540VRD

User Manual

2

3

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

PROCUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT

THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

CAUTION

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to

alert the user to the presence of uninsulated "dangerous voltage" within the product’s

enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the literature

accompanying the appliance.

4

FCC COMPLIANCE STATEMENT

INFORMATION TO THE USER: THIS EQUIPMENT HAS BEEN TESTED AND FOUND

TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF

THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION

AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A

COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE

RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH

THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO

COMMUNICATIONS.

OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL

INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE

INTERFERENCE AT HIS OWN EXPENSE.

INFORMATION TO THE USER: THIS EQUIPMENT HAS BEEN TESTED AND FOUND

TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF

THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION

AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A

COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE

RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH

THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO

COMMUNICATIONS.

OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL

INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE

INTERFERENCE AT HIS OWN EXPENSE.

CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY

RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE

THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

CET APPAREIL NUMERIQUE DE LA CLASSE A SET CONFORME A LA NORME NMB-003 DU

CANADA.

CE COMPLIANCE STATEMENT

WARNING: This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

5

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been moisture, does not

operate normally, or has been dropped.

15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY

QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF

ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN

THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU

QRE QUALIFIED TO DO SO.

16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed

Class 2 power source only.

17. ITE is to be connected only to PoE networks without routing to the outside

plant.

6

Table of Contents

1. Product Description…………………………………………………………………………………………………7

2. Installation……………………………………………………..........................…………..……………….9

3. Operation…………………………………………………………………………………………………………….14

3.1 Access from a browser …………………………………………………………………………………..14

3.2 Access from the internet ………………………………………………………………………………..15

3.3 Setting the admin password over a secure connection…………………………….…….…15

3.4 Live View Page ………………………………………………………………………………………………16

3.5 Camera Setup (Analog)……………………………………………………………………………….….18

3.5.1 Settings…………………………………………………………………………………………………..18

3.5.2 Lens Adjustment (Optical Vari-focal Lens)…………………………………………………..24

3.6 Network Camera Setup………………………………………………………………………………...25

3.6.1 Basic Configuration…………………………………………………………………….…………...26

3.6.1.1 Users…………………………………………………………………………………….………...26

3.6.1.2 Network……………………………………………………………………………….…………...27

3.6.1.3 Video & Image..……………………………………………….……………………………...28

3.6.1.4 Audio..…..……………………………………………………….…………………………….....31

3.6.1.5 Date & Time..……………………………………………………………………….………...32

3.6.2 Video & Image..……………..……………………………………………………………………....33

3.6.3 Audio..……………………………….………………………………………………………………....36

3.6.4 Event………………………………………………………………………………………………………37

3.6.4.1 Event-In…………………………………………………………………………………………….37

3.6.4.2 Event-Out………………………………………………………………………………………….42

3.6.4.3 Event Map…………………………………………………………………………………………49

3.6.5 System……………………………………………………………………………………….………...50

3.6.5.1 Information………………………………………………………….…………………………...50

3.6.5.2 Security..…………………………………………………………….…………………………...51

3.6.5.3 Date & Time..…………………………………………………………………….…………...54

3.6.5.4 Network..……………………………………………………………………….……………....55

3.6.5.5 Language..……………….…………………………………….……………………………....62

3.6.5.6 Maintenance..……………..………………………………….…..........................…....63

3.6.5.7 Support............……………………………………….........................….…………....64

3.7 About……………..………………………..…………………………………………………….…………....64

3.8 camera Menu Control.……….……..…………………………………………………….…………....65

3.9 Help…………………………………………….……………………………………………………………....66

3.10 Resetting to the factory default settings……………….……………………………………....67

4. Appendix ……………………………………………………………..……………………………………….……68

4.1. Troubleshooting.…………………………..……………………………………………………….……68

4.2. Preventive Maintenance..………………………..........................….…………………….……69

4.3. Product Specification…..………………………………………………………………..….….....……70

7

1. Product Description

This manual applies to the VIP2 Camera – VK2-540VRD.

The VK2-540VRD vandal resistant dome is a Hybrid analogue and IP camera. It has a

standard composite BNC out put allowing it to be connected via coax to a traditional coax

based CCTV system, as well as being connected to an IP based system.

The VK2-540VRD comes supplied with its own viewing software which allows the user to

View, record and configure the camera. Viewing and configuration can also be carried out

via a web browser such as Internet Explorer.

The camera can transmit real time full frame rate video in H.264, MJPEG or MPEG4

compression formats.

The alarm input and alarm output can be used to connect various third party devices, such

as, door sensors and alarm bells.

Components

The system comes with the following components:

VK2-540VRD Installation CD Installation Guide

Note: Check your package to make sure that you received the complete system, including

all components shown above.

8

Key Features

• Brilliant video quality

The VK2-540VRD offers the highly efficient H.264 video compression, which drastically

reduces bandwidth and storage requirements without compromising image quality. Motion

JPEG is also supported for increased flexibility.

• Dual streams

The VK2-540VRD can deliver dual video streams simultaneously at full frame rate in all

resolutions up to D1 (720x480 in NTSC, 720x576 in PAL) using Motion JPEG and H.264 (or

MPEG-4). This means that several video streams can be configured with different

compression formats, resolutions and frame rates for different needs.

• Image setting adjustment

The VK2-540VRD also enables users to adjust image settings such as contrast, brightness

and saturation to improve images before encoding takes place.

• Intelligent video capabilities

The VK2-540VRD includes intelligent capabilities such as enhanced video motion detection.

The encoder’s external inputs and outputs can be connected to devices such as sensors and

relays, enabling the system to react to alarms and activate lights or open/close doors.

• Power over Ethernet

Support for Power over Ethernet (IEEE802.3af) enables the unit, as well as the analog

camera that is connected to it, to receive power through the same cable as for data

transmission. This makes for easy installation since no power outlet is needed.

• Audio support

The VK2-540VRD also supports two-way audio.

• Improved Security

The VK2-540VRD logs all user access, and lists currently connected users. Also, its full

frame rate video can be provided over HTTPS.

• Camera

-. Superior image quality (540 TV Lines).

-. 0.3 Lux (Color) @ F1.2 Sensitivity.

-. C/CS, backfocus cam for easy adjustment.

-. Auto electronic shutter [1/60(1/50) ~ 1/100,000] and manual electronic shutter modes.

-. Full control via the OSD menu key on the side of the camera.

-. Auto and manual white balance modes.

-. BLC (Back Light Compensation)

-. Day&Night (Auto / Color / B/W)

-. AGC (Auto Gain Control)

-. Incredible noise reduction for picture quality & file size.

-. Sens-up (x2 ~ x128)

-. Privacy Zone 8 points.

-. MIRROR

-. VIDEO OUT(BNC)

9

2. Installation

For the operation of the VK2-540VRD, it is necessary to connect a network cable for data

transmission, power connection from supplied power adapter and connect a general analog

camera. Depending on operation methods, it is possible to connect an alarm cable or audio

cable additionally. For its fixation on different locations, please consult with an installer.

Overview

• Top View

NO

Name

Description

1

Lens

Allows wide area to be monitored

2

Extension Cable

26pin camera extension cable

• Extension Cable

10

NO

Wire Color

Description

1

Red: AC24V/DC12V

White: AC24V/GND

Main Power, 2pin terminal, DC12V/AC24V, max. 6.5W

2

Orange: AC24V/DC12V

Black: AC24V/GND

Heater Power, 2pin terminal, max. 10Watt @ DC12V,

max. 20Watt @ AC24V

3

Pink: Alarm In

Yellowish Green: GND

Yellow: AD Key

Brown: GND

Light Blue: Alarm Out

Gray: GND

Alarm Input, AD Key Input, Alarm Output:

6pin terminal.

4

Black

Ethernet, RJ-45 port compatible with 10/100Mbps PoE.

Modular Jack

5

Black

Video Composite Output, BNC Jack

6

Gray

Audio line output, Stereo Jack

7

Black

Audio line input, Stereo Jack

Caution: Never aim the camera directly into the sun.

Base Installation

1. Make mounting holes and cable hole in the place (ceiling) to which this dome camera

is installed using the supplied template sheet.

Warning: The total mass of the main unit is approx 1.3kg. Check whether the ceiling

to which the Dome Camera is installed is strong enough to hold the unit mass. If not,

the Dome Camera could fall, causing injury.

2. Attach the safety wire for securing the dome camera to ceiling or structure not to fall.

3. Extract each wire through the cable hole, connect BNC cable and communication lines.

11

4. Unlock torx screws (4x) the dome cover and fix the dome case firmly with supplied

mounting screws (4x), plastic anchors (4x), O-Rings (4x).

5. Adjust desired focus and scene by turning and moving the hemisphere by hand.

6. Lock the housing cover with torx screws (4x).

• Cable through the electrical box with the dome base

The housing can also be mounted on a 4s or 2s electrical box.

• Using the conduit knockout punched with the dome base

Remove the conduit knockout punched for the cable entry.

12

Heater Kit Installation

1. Place the heater element is slot “A”. Please ensure that the cables are facing upwards

and the heater is pointing towards the Dome.

2. Place the PCB in slot “B”. Please ensure that the PCB is facing inside of the Dome with

the connection blocks at the top.

3. Place the plug in the Socket “C” (J3) which is found on the controller board.

• Cheater (IF Applicable)

Power Supply

24VAC

12DCV

Power Consumption

20Watt

10Watt

Heater On

at 41°F (5°C)

Heater Off

at 59°F (15°C)

• Power

Use Certified/Listed Class 2 power source only.

13

Network Connection

The VK2-540VRD supports the operation through the network. Therefore, it is necessary to

connect a standard RJ-45 cable to it. Generally a cross-over cable is used for directly

connection to PC, while a direct cable is used for connection to a hub.

IP Assignment

When a camera, Encoder or Decoder is first connected to the network it has no IP address.

So, it is necessary to allocate an IP address to the device with the “Smart Manager” utility

on the CD.

1. Connect the VK2-540VRD to the network and power up.

2. Start SmartManager utility (All programs > VIP2 > SmartManager), the main window

will be displayed, after a short while any cameras connected to the network will be

displayed in the list.

3. Select the camera on the list and click right button of the mouse. You can see the pop-

up menu as below.

4. Select Assign IP. You cam see a Assign IP window.

Enter the required IP address.

14

The description of each field for the connection status follows.

: Available for connection to the camera

: Loading settings information of video after connecting the camera.

: Connectable to the camera but fixed security settings (password)

: Unavailable for connection to the camera (PC can not access relevant IP Address)

Note: Refer to VIP2 Client Software User’s Manual for detailed information.

3. Operation

The VK2-540VRD can be used with most standard operating systems and browsers.

Notes: To view streaming video in Microsoft Internet Explorer, set your browser to allow ActiveX

controls.

3.1 Access from a browser

1. Start a browser (Internet Explorer).

2. Enter the IP address or host name of VK2-540VRD in the Location/Address field of

your browser.

3. You can see a starting page. Click Live View or Setup to enter web page.

15

4. The encoder’s Live View page appears in your browser.

3.2. Access from the internet

Access from the internet Once connected, the VK2-540VRD is accessible on your local

network (LAN). To access the VK2-540VRD from the Internet you must configure your

broadband router to allow incoming data traffic to it. To do this, enable the NAT-traversal

feature, which will attempt to automatically configure the router to allow access to the VK2-

540VRD. This is enabled from Setup > System > Network > NAT.

For more information, please see NAT traversal (port mapping) for IPv4, on page 61.

3.3 Setting the admin password over a secure connection

To gain access to the product, the password for

the default administrator user must be set. This

is done in the “Admin Password” dialog, which is

displayed when the VK2-540VRD is accessed for

the setup at the first time. Enter your admin

name and password, set by the administrator.

Note: The default administrator username and

password is “admin”. If the password is lost, the

VK2-540VRD must be reset to the factory default

settings. See “3.9 Resetting to the factory default

settings”.

To prevent network eavesdropping when setting the admin password, this can be done via

an encrypted HTTPS connection, which requires an HTTPS certificate (see note below).

To set the password via a standard HTTP connection, enter it directly in the first dialog

shown below. To set the password via an encrypted HTTPS connection, see Setup >

System > Secutity > HTTPS, on page 52.

16

Note:

HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic

between web browsers and servers. The HTTPS certificate controls the encrypted exchange

of information. The default administrator user cannot be deleted.

3.4 Live View Page

The live view page comes in eight

screen modes like 704x480(576),

704x240(288), 352x240(288),

176x120(144), 640x480, 320x240,

and 160x120. Users are allowed to

select the most suitable one out of

those modes. Please, adjust the

mode in accordance with your PC

specifications and monitoring

purposes.

• General controls

The video drop-down list allows you to select a customized or pre-

programmed video stream on the live view page. Stream profiles are configured under

Setup > Basic Configuration > Video & Image. See Basic Configuration, on page 25 for

more information.

The resolution drop-down list allows you to select the most suitable

one out of video resolutions to be displayed on live view page.

The protocol drop-down list allows you to select which combination of

protocols and methods to use depends on your viewing requirements, and on the

properties of your network.

• Control toolbar

The live viewer toolbar is available in the web browser page only. It displays the following

buttons:

The Stop button stops the video stream being played. Pressing the key again toggles the

start and stop. The Start button connects to the network camera or start playing a

video stream.

The Pause button pause the video stream being played.

The Snapshot button takes a snapshot of the current image. The location where the

image is saved can be specified.

17

The digital zoom activates a zoom-in or zoom-out function for video image on the live

screen.

The Full Screen button causes the video image to fill the entire screen area. No other

windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full

screen view.

The Manual Trigger button activates a pop-up window to manually start or stop the

event.

The Camera Menu button activates a pop-up window for camera menu control.

Use this scale to control the volume of the speakers.

Use this scale to control the volume of the microphone.

Use this scale to control the volume of the speakers and microphones.

• Camera Menu controls

If the VK2-540VRD has been appropriately configured, the Live View page displays the

controls available for the OSD menu.

Please see “3.8 Camera Menu Control for more information.

• Video and Audio Streams

The camera can provide several images and video stream formats. Your requirements and

the properties of your network will determine the type you use.

The Live View page in the camera provides access to H.264, MPEG-4 and Motion JPEG

video streams, and to the list of available video streams. Other applications and clients can

also access these video streams/images directly, without going via the Live View page.

18

3.5 Camera Setup (Analog)

3.5.1 Settings

Settings can be made using the 5 buttons located on the back of the camera.

▶ Structure of menu setup

19

▶ LENS (Selection)

This function is used to adjust the brightness of the screen.

1. When the SETUP menu is displayed on the screen, please position the arrow to point

to LENS by using the UP and DOWN buttons.

2. Please select the type of the lens you wish to use by pressing the LEFT or RIGHT

button.

Note: The brightness of the screen can be adjusted in DC mode.

The brightness can be adjusted within the range of 0 ~ 100.

The optimum level of brightness for the user can be achieved by adjustment.

▶ EXPOSURE

The EXPOSURE menu is used to set the automatic light control method for this camera.

-. SHUTTER:

Select the shutter mode. (1/60(50), FLK~1/100,000 sec, x2~x256)

Can be changed while in shutter mode.

-. BRIGHTNESS:

Adjust BRIGHTNESS level (0~100).

Can be changed while in manual lens mode.

-. AGC:

Auto gain control (OFF/LOW/MIDDLE/HIGH)

-. SENSE-UP:

Use under very light condition for full color surveillance.

Select maximum Low-Shutter value. (x2 ~ x256)

-. BLC:

Sharpness subjects with backlight. (OFF/BLC/HBLC)

-. D-WDR:

Digital wide dynamic range. (OFF/INDOOR/OUTDOOR)

20

[BLC MODE]

▶ WHITE BAL

The Screen color can be adjusted by using the WHITE BALANCE function.

-. AWB:

Wide range auto white balance mode.

-. AWC => SET:

Please press the ENTER button while the camera is directed at a piece of while paper to

obtain the optimum state under current illumination. If the environment including the

light source is changed, you have to adjust the wide balance gain.

-. MANUAL:

Manual mode. User can change R and B gain manually.

-. INDOOR:

Set the color temperature to 3200K

-. OUTDOOR:

Set the color temperature to 6300K

-. ATW:

Set the color temperature to 2500K to 9500K

[WHITE BAL MANUAL MODE]

Page is loading ...

Vista VIP2 VK2-540VRD User manual

This manual is also suitable for

Vista VIP2 VK2-540VRD User manual

Related papers

Other documents