Vista Onvif VK2-1080XPTZ User manual

VK2-1080XPTZ

User Manual

VK2-1080XPTZ User Manual V1.0

2

VK2-1080XPTZ User Manual V1.0

3

Before You Begin

Read these instructions before installing or operating this product.

Note: This installation should be made by a qualified service person and should conform to local codes.

This manual provides installation and operation information. To use this document, you must have the following

minimum qualifications:

 A basic knowledge of CCTV systems and components

 A basic knowledge of electrical wiring and low-voltage electrical connections

Intended use

Only use this product for its designated purpose; refer to the product specification and user documentation.

Customer Support

For assistance in installing, operating, maintaining and troubleshooting this product refer to this document and any other

documentation provided. If you still have questions, please contact Norbain Technical Support and Sales:

Norbain SD Ltd, 210 Wharfedale Road, IQ Winnersh, Wokingham, Berkshire RG41 5TP, England.

UK +44 (0) 118 912 5000

Note: You should be at the equipment and ready with details before calling Technical Support.

Conventions Used in this Manual

Boldface or button icons highlight command entries. The following WARNING, CAUTION and Note statements identify

potential hazards that can occur if the equipment is not handled properly:

* WARNING:

Improper use of this equipment can cause severe bodily injury or equipment damage.

** Caution:

Improper use of this equipment can cause equipment damage.

Note: Notes contain important information about a product or procedure.

This apparatus is manufactured to comply with the radio interference.

A Declaration of Conformity in accordance with the following EU standards has been made. The

manufacturer declares that the product supplied with this document is compliant the provisions of the

EMC Directive 2004/108/EC, the CE Marking Directive 93/68 EEC and all associated amendments.

All lead-free products offered by the company comply with the requirements of the European law on the

Restriction of Hazardous Substances (RoHS) directive: 2011/65/EU, which means our manufacture

processes and products are strictly “lead-free” and without the hazardous substances cited in the

directive.

The crossed-out wheeled bin mark symbolizes that within the European Union the product must be

collected separately at the product end-of-life. This applies to your product and any peripherals marked

with this symbol. Do not dispose of these products as unsorted municipal waste.

* This symbol indicates electrical warnings and cautions.

** This symbol indicates general warnings and cautions.

NORBAIN SD LTD reserves the right to make changes to the product and specification of the product from time to time

without prior notice.

VK2-1080XPTZ User Manual V1.0

4

WARNINGS AND CAUTIONS:

To reduce the risk of fire or electric shock, do not insert any metallic objects through the ventilation grills or other

openings on the equipment.

CAUTION

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

VK2-1080XPTZ User Manual V1.0

5

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

1. Keep these instructions.

2. Heed all warnings.

3. Follow all instructions.

4. Do not use this apparatus near water.

5. Clean only with dry cloth.

6. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

8. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide blade or the third prong is

provided for your safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

9. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

10. Only use attachments/accessories specified by the manufacturer.

11. Use only with the cart, stand, tripod, bracket, or table specified

by the manufacturer, or sold with the apparatus. When a cart is

used, use caution when moving the cart/apparatus combination

to avoid injury from tip-over.

12. Unplug this apparatus during lightning storms or when unused

for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

14. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED

SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE

OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.

15. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2

power source only.

16. ITE is to be connected only to PoE networks without routing to the outside plant.

VK2-1080XPTZ User Manual V1.0

6

TABLE OF CONTENTS

1. DESCRIPTION ............................................................................................................... 8

1.1 Key Features ....................................................................................................................... 9

2. INSTALLATION............................................................................................................ 10

Before Installation .................................................................................................................. 10

2.1 Base Installation ............................................................................................................... 10

2.2 Basic Configuration of Dome Camera System ............................................................... 13

2.3 Setting Network Dome Camera Termination .................................................................. 14

Reset .................................................................................................................................... 14

Setting the RS485 Dome Camera Address (ID) ................................................................. 15

Setting the RS485 Dome Protocol ..................................................................................... 15

Connections ........................................................................................................................ 15

.................................................................................................... Error! Bookmark not defined.

2.4 Setting the cameras IP address ....................................................................................... 16

2.5 Network Connection & IP assignment ............................................................................ 18

3. Operation ..................................................................................................................... 19

3.1 Access from a browser .................................................................................................... 19

3.2 Access from the internet .................................................................................................. 20

3.3 Setting the admin password over a secure connection ................................................ 20

3.4 Live View Page ................................................................................................................. 21

3.5 VK2-1080XPTZ Setup ...................................................................................................... 23

3.5.1 Basic Configuration ................................................................................................... 23

1) Users ............................................................................................................................ 24

2) Network ........................................................................................................................ 25

3) Video & Image ............................................................................................................. 26

4) Audio ............................................................................................................................ 28

5) Date & Time ................................................................................................................. 29

3.5.2 Live View .................................................................................................................... 30

3.5.3 Video & Image ............................................................................................................ 30

1) Basic ............................................................................................................................ 30

2) Image............................................................................................................................ 31

3) Auto Exposure ............................................................................................................. 32

4) Day & Night .................................................................................................................. 33

5) Auto Focus .................................................................................................................. 34

6) DIS ................................................................................................................................ 35

7) Webcasting .................................................................................................................. 35

VK2-1080XPTZ User Manual V1.0

7

3.5.4 Audio .......................................................................................................................... 36

3.5.5 Event ........................................................................................................................... 36

1) Event In ........................................................................................................................ 36

2) Event Out ..................................................................................................................... 40

3) Event Map .................................................................................................................... 46

3.5.6 Dome Configuration ................................................................................................... 48

1) Preset ........................................................................................................................... 48

2) Tour .............................................................................................................................. 49

3) Motor Setup ................................................................................................................. 50

4) RS485 ........................................................................................................................... 51

5) View Angle ................................................................................................................... 51

6) System Menu ............................................................................................................... 52

7) Privacy Zone ................................................................................................................ 53

3.5.7 System ........................................................................................................................ 54

1) Information .................................................................................................................. 54

2) Security ........................................................................................................................ 54

3) Date & Time ................................................................................................................. 56

4) Network ........................................................................................................................ 58

5) Language ..................................................................................................................... 66

6) Maintenance ................................................................................................................ 67

7) Support ........................................................................................................................ 68

3.6 Help ................................................................................................................................... 70

3.7 Resetting to the factory default settings......................................................................... 70

4. Appendix ..................................................................................................................... 71

4.1 Troubleshooting ............................................................................................................... 71

4.2 Alarm Connection ............................................................................................................. 72

4.3 Preventive Maintenance ................................................................................................... 72

4.4 Product Specification ....................................................................................................... 73

4.5 System Requirement for Web Browser ........................................................................... 75

4.6 General Performance Considerations ............................................................................. 75

VK2-1080XPTZ User Manual V1.0

8

1. DESCRIPTION

-------------------------------------------------------------------------------------------------------------------------------------

This manual applies to the VK2-1080XPTZ fully functional PTZ network camera.

These cameras are fully featured for security surveillance and remote monitoring needs. They are

based on the DSP compression chip, allowing real-time, full frame rate Motion JPEG and H.264 (or

MPEG-4) video streams.

Components

Quantity

Description

1

Camera

1

Bubble Ring

3

Assembly Screws for Attaching Network Dome Camera

1

Installation CD

3

Rawl plugs

NOTE

Adapter for DC12V / AC24V are not supplied.

VK2-1080XPTZ User Manual V1.0

9

1.1 Key Features

 HDTV Video Quality

The VK2-1080XPTZ is capable of providing the outstanding image quality with HDTV performance

and profiles (High, Main, and Baseline) in H.264 compression.

 Triple Streaming

Each stream can be programmed independently and transmitted using different configurations.

 Codecs

The camera supports thre standard compressions formats H.264, MJPEG and MPEG4

 Built-in optical Zoom

Support maximum 30x optical

 Intelligent Video Motion Detection

The HDS Series offers intelligent & sophisticated video motion detection for each multiple streams.

 Triple Power (Power over Ethernet, DC12V, AC24V)

This camera supports Power over Ethernet (PoE), which supplies power to the camera through the

network. If the network has no PoE, connect a DC12V or AC24V power connector.

 Day and Night

The HDS Series provide clear monitoring images even in low light conditions using IR-cut filter.

 Voice Alert Linked to Alarm Detection

The HDS Series can play the audio file stored in the camera in synchronization with alarm

detection by the sensor input or the motion detection function.

 Network Flow Control

The HDS Series provides a flow control function which enhances network efficiency by significantly

restricting user video streams with designating the maximum bandwidth.

 ONVIF Certificate

The HDS Series network camera complies with the ONVIF certificate. ONVIF (Open Network

Video Interface Forum) is an open industry forum for the development of a global standard for the

interface of network video product.

VK2-1080XPTZ User Manual V1.0

10

2. INSTALLATION

-------------------------------------------------------------------------------------------------------------------------------------

Before Installation

Before installing the camera, thoroughly familiarize yourself with the information in this section of

the manual.

- Recommend connecting the camera to a network that uses a DHCP (Dynamic Host Configuration

Protocol) server to address devices.

- To ensure secure access to the IP camera, place the camera behind a firewall when it is

connected to a network.

2.1 Base Installation

Typical System Configuration

VK2-1080XPTZ User Manual V1.0

11

Assemble bubble ring ass’y(Optional)

NOTES

It is recommended that the camera window is removed when you use bubble ring assembly is used; this will improve the

picture quality.

The Network Dome Camera is for use in surface mounting applications and the mounting surface

should be capable of supporting loads up to 10lb (4.5kg).

The Network Dome Camera’s base should be attached to a structural object, such as hard wood,

wall stud or ceiling rafter that supports the weight of the Network Dome Camera.

Installation

push

remove window

assemble bubble ring ass'y

push

remove camera window

bubble ring ass'y

screw

VK2-1080XPTZ User Manual V1.0

12

Dimensions

VK2-1080XPTZ User Manual V1.0

13

2.2 Basic Configuration of Dome Camera System

Basic installation diagram

The Network Dome Camera must be installed by qualified service personnel in accordance with all

local and federal electrical and building codes. The system should be installed according to Figures

5 through 8.

VK2-1080XPTZ User Manual V1.0

14

Layout of Switches

2.3 Setting Network Dome Camera Termination

The device which is connected at end of line, whether it is a Network Dome Camera or keyboard

controller, must have the cable for communication terminated by setting the appropriate DIP switch.

Without proper termination, there is potential for control signal errors. Total length of the cable for

communication should not exceed 1.2km (4000ft).

Figure 1. Setting

Network Dome Camera Termination

Reset

To restore the camera’s factory default settings. Turn on dip switch 2 for 15s and then turn off.

Please take steps as follows:

1. Power off

2. Move switch 2 to On

3. Power up the camera

4. wait for 15 seconds and move SW2 to off

SW1

1

2

Terminated

ON

RESET

Not terminated

OFF

VK2-1080XPTZ User Manual V1.0

15

Setting the RS485 Dome Camera Address (ID)

Each Dome Camera must have a unique address (ID). When installing multiple Network Dome

Cameras using a multiplexer, it is suggested that the Network Dome Camera address match the

multiplexer port number.

If you want to set the address more than 999, you should contact the service provider.

Refer to ‘Dome Configuration - RS485’ section for detailed information.

Setting the RS485 Dome Protocol

Refer to ‘Dome Configuration - RS485’ section for detailed information.

Connections

 Connecting to the RS485

The Network Dome Camera can be controlled remotely by an external device or control system,

such as a control keyboard, using RS485 half-duplex serial communications signals. Connect

Marked Rx+, Rx- to Tx+ and Tx- of the RS485 control system.

 Connecting Alarms

AL1 (Alarm In)

You can use external devices to signal the Network Dome Camera to react on events. Mechanical

or electrical switches can be wired to the AL (Alarm In) and GND (Ground) connectors.

GND(Ground)

Connect the ground side of the Alarm input and/or alarm output to the GND connector.

NC (NO) (Normal Close or Normal Open: Alarm Out)

The Network Dome Camera can activate external devices such as buzzers or lights. Connect the

device to the NC (NO) (Alarm Out) and COM (Common) connectors.

VK2-1080XPTZ User Manual V1.0

16

 Connecting the Network

The Network Dome Camera supports the operation through the network. Therefore, it is necessary

to connect a standard RJ-45 cable to it. Generally a cross cable is used for directly connection to

PC, while a direct cable is used for connection to a hub.

 Connecting the Power

Connect power of 12VDC or 24VAC 1.5A for the camera.When using a 12VDC adapter,

connect the positive (+) pole to the ‘+’ position and

the negative (-) pole to the ‘-’ position.

Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source

only.

- Be careful not to reverse the polarity when you connect the power cable.

- You can also use a router featuring PoE (Power over Ethernet) to supply power to the

camera.

- If PoE and 12VDC are both applied, this camera will get supplied with power from PoE.

- 24VAC is recommended to use for the camera power for stable operation with heater kit.

If using PoE, the heater will not operate at all.

2.4 Setting the cameras IP address

IP Assignment

When a camera is first connected to the network it has no IP address. So, it is necessary to

allocate an IP address to the device with the “Smart Manager” utility on the CD.

1. Connect the Network Camera / device to the network and power up.

2. Start Smart Manager utility, the main window will be displayed, after a short while any network

devices connected to the network will be displayed in the list.

3. Select the camera on the list and click right button of the mouse. You will see the following

menu as below:

VK2-1080XPTZ User Manual V1.0

17

4. Select Assign IP. You cam see an Assign IP window.

5. Enter the required IP address.

The description of each field for the connection status follows.

: Available for connection to the camera

: Loading settings information of video after connecting the camera.

: Connectable to the camera but fixed security settings (password)

: Unavailable for connection to the camera (PC can not access relevant IP Address)

Note: For more information, refer to the Smart Manger User’s Manual.

VK2-1080XPTZ User Manual V1.0

18

2.5 Network Connection & IP assignment

The camera supports the operation through the network. When a camera is first connected to the

network, it is necessary to allocate an IP address to the device with the “SmartManager” utility on

the CD. (Default IP 192.168.30.220)

1) Connect the network camera/device to the network and power up.

2) Start SmartManager utility (Start > All programs > SmartManager > SmartManager). The main

window will display, and after a short while any network devices connected to the network will

be displayed in the list.

3) Select the camera on the list and click right button of the mouse. You can see the pop-up

menu as below.

4) Select Assign IP Address. The Assign IP window will display. Enter the required IP address.

NOTE: More if multiple cameras are selected then a range of Ip addresses can be configured.

For more information, refer to the SmartManager User’s Manual.

VK2-1080XPTZ User Manual V1.0

19

3. Operation

The VK2-1080XPTZ can be used with Windows® operating system and browsers. The

recommended browsers are Internet Explorer®, Safari®, Firefox®, Opera™ and Google®

Chrome® with Windows.

NOTE: To view streaming video in Microsoft Internet Explorer, set your browser to allow ActiveX

controls.

3.1 Access from a browser

1) Start a browser (Internet Explorer).

2) Enter the IP address or host name of the in the Location/Address field of your browser.

3) You can see a starting page. Click Live View or Setup to enter web page.

4) The network camera’s Live View page appears in your browser.

VK2-1080XPTZ User Manual V1.0

20

3.2 Access from the internet

Once connected, the VK2-1080XPTZ is accessible on your local network (LAN). To access the

VK2-1080XPTZ from the Internet you must configure your broadband router to allow incoming

data traffic to the network camera. To do this, enable the NAT traversal feature, which will attempt

to automatically configure the router to allow access to the network camera. This is enabled from

Setup > System > Network > NAT. For more information, please see “3.5.7 System > Network >

NAT” of User's Manual.

3.3 Setting the admin password over a secure connection

To gain access to the product, the password for the default administrator user must be set. This is

done in the “Admin Password” dialog, which is displayed when the VK2-1080XPTZ is accessed for

the setup at the first time. Enter your admin name and password, set by the administrator.

NOTE: The default administrator user name and password is “admin”. If the password is lost, the

must be reset to the factory default settings. Please see “Resetting to the factory default

settings”.

To prevent network eavesdropping when setting the admin password, this can be done via an

encrypted HTTPS connection, which requires an HTTPS certificate (see NOTE below).

To set the password via a standard HTTP connection, enter it directly in the first dialog shown

below. To set the password via an encrypted HTTPS connection, please see “3.5.7 System >

Security > HTTPS” of User's Manual.

NOTE: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic

between web browsers and servers. The HTTPS certificate controls the encrypted

exchange of information.

Page is loading ...

Vista Onvif VK2-1080XPTZ User manual

Vista Onvif VK2-1080XPTZ User manual

Related papers

Other documents