PR Lighting PR-6000 Wash User manual

1

PR-6000 Wash (2000W Version)

PR-6000 Wash (1500W Version)

PR-6000 Wash (1400W Version)

The user manual contains important information about the safe installation and use of a projector.

Please read and follow these instructions carefully and keep the manual in a safe place for future

reference.

PR LIGHTING LTD.

http://www.pr-light ing.com

2

INDEX

1. SAFETY AND WARNINGS ……………………………………………………………………………

3

2. INSTUCTIONS ………………………………………………………………………………………

4

●CLEANING AND MAINTENANCE………………………………………………………………………4

●LUBRICATION……………………………………………………………………………………………4

●TROUBLESHOOTING…………………………………………………………………………………

5

3. APPEARANCE……………………………………………………………………………………………

5

4. INSTALLATION …………………………………………………………………………………………… 5

●RIGGING ………………………………………………………………………………………………

5

●POWER CONNECTIONS …………………………………………………………………………

6

●DMX CONTROL CONNECTION………………………………………………………………………

6

●DMX TERMINATOR……………………………………………………………………………………

7

●ALIGNMENT/INSTALLATION/REPLACEMENT OF A LAMP ……………………………………

7

5. SETUP AND CONFIGURATION…………………………………………………………………………

8

●FRONT PANEL OPERATION ………………………………………………………………………

8

●DMX START ADDRESS………………………………………………………………………………

8

●DMX WIRELSESS CONTROL …………………………………………………………………………

8

●STAND-ALONE MODE ……………………………………………………………………………

8

●MASTER/SLAVE MODE ………………………………………………………………………………

9

6.OPERATION MENU ………………………………………………………………………………………

9

7. DMX PROTOCOL ………………………………………………………………………………………

13

8. LED INDICATION ………………………………………………………………………………………

15

9. ERROR MESSAGE ……………………………………………………………………………………

15

10.TECHNICAL DATA ………………………………………………………………………………………

16

11.CIRCUIT DIAGRAM AND PCB CONNECTIONS ………………………………………………………

20

●The circuit diagram of 2000W lamp, ballast and igniter …………………………………………………

20

●The circuit diagram of 1500W lamp, ballast and igniter ………………………………………………… 21

12.COMPONENT ORDER CODES …………………………………………………………………………22

ACCESSORIES

The following items are supplied with the projector and please check:

Name

Quantity

Unit

Remark

G clamp

2

Pcs

XLR

Connector

1

Set

Male and female

Safety cord

2

Pc

s

Spare

Gobo

4

pc

s

User

manual

1

Pc

s

Ω clamp

2

Pcs

Optional

Please note that as part of our ongoing commitment to continuous product development,

specifications are subject to change without notice. Whilst every care is taken in the preparation of

the manual we reserve the right to change specifications in the course of product improvement. The

publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the

packing and / or the unit is in good condition before installation and use. Should there be any damage

caused by transportation, consult your dealer and do not use the unit. Any damage caused by

improper use will not be assumed by the manufacturer and / or dealer.

Any future technical change in the user manual won’t be with any notice.

Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product is

one year starting from the delivery date but the light source is not within the warranty.

3

1. SAFETY AND WARNINGS

NOTE

Before a projector’s installation, power-on, operation and maintenance, please carefully read

the safety information hereinafter!

The following safety signs are used in the user manual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , check if there is transportation damage before using the projector. Should there be

any damage caused by transportation, consult your dealer and do not use it.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the

projector as he/she likes

●Please be noted that the damage caused by changing the projector at will is not warranted.

● Do not hesitate to contact the dealer or the manufacturer if any questions or advice.

● The projector is for indoor use only, IP20.

● Use only in dry locations. Keep this unit away from rain and moisture, excessive heat, humidity and dust. Do

not allow contact with water or any other liquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light

while being operated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operation must strictly follow the procedures in the manual

●No repairable parts in the projector and do not open covers for maintenance by yourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.

●Do not connect this device to any type of dimmer pack

●After lamp switched on, the minimum distance between the projector and illuminated surface is 10m

●lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise

the light output will be compromised.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use

a projector while covers(housing)are off

●Keep the lamp clean and do not touch it with bare hands.

●While operating it, wear protective items.

●Any electrical connection must be carried out by a qualified person .

●Before installation, please confirm the voltage supplied matches what is required for the projector

●Each projector must be properly earthed and installed as per related electrical standards.

●Do not use power cord with its insulator damaged and connect the power cord with other cables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it

forcefully or by pulling the power cable.

●All power cords must conform to related safety and regulations

●While being operated, the projector should not be under rains or in humidity.

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and

other electrical parts’ life will be shortened .

4

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the

safety cord supplied through the safety cord holes for safety support.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected

from power mains.

●After running for 30minutes, the temperature of the housing of the projector is 45 .After stable ℃

operation , its temperature is 80 .℃

●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does

not mean the projector has some defects.

●Do not mount the projector directly on inflammable surface.

●Do not project the beam straightly on combustible items and the minimum distance between the

projector and illuminated items is 10m.

●A projector should be installed with good ventilation and the minimum distance between the

projector and walls is 50cm. At the same time, please ensure the fans and air inlets and outlets are

workable.

2. INSTRUCTIONS

●CLEANING AND MAINTENANCE

If a projector can’t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the

projector has over-temperature protective device. If the temperature is too high, the protective device will be triggered to

shut the projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue

is solved, restart the projector.

The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is very

necessary to ensure a reliable use of it. Cooling fans need to be cleaned every 15days. Internal lens, reflector and hot mirror

need to be cleaned periodically to optimize light output.

Cleaning frequency is to be decided by operations and its environment. Use soft cloth and normal detergent for glass for

cleaning work. It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days.

Keep lens clean and do not touch optical parts with bare hands.

●Before any maintenance and cleaning, please ensure the project is off the power

●Only qualified person is allowed to do maintenance

●During maintenance and before maintenance, the projector must be off power.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens

whether it runs or not

●Do not use alcohol or other organic solvent to clean the housing to avoid damage.

●Do not use any solvent with chemical elements to clean color filters or hot mirror.

●LUBRICATION

To ensure smooth movement of gobos and zoom and focus lens, it’s advised rotators’ bearings and 2 sliding bars for zoom

and focus lens be lubricated every 2 months. High quality and high temperature lubricant/grease is advised..

●TROUBLESHOOTING

PROBLEM ACTION

The projector doesn’t switch on

 Check the fuse on the power socket.

 Check the lamp.

The lamp is on but the projector doesn’t respond  Make sure that the fixture’s start address is right

5

to the controller  Replace or repair the XLR signal cable.

The projector functions intermittently  Make sure the fan is working well or fans and their shields are not blocked

Beam appears dim, Low in brightness

 Make sure the lamp is within its lifespan

 Remove dust or grease from the lenses.

The project image appears to have a halo  Carefully clean the lamp, optical lenses and other components.

Heavily Defective Beam

 Check if lens are in good condition(not cracked)

 Clean dust or grease on the lens.

3. APPEARANCE

4. INSTALLATION

●RIGGING

Before moving a projector, Please lock Pan and Tilt. Before its operation, please unlock them. It’s forbidden to run a

projector with power while it is locked

106

256

HANDLE

SAFETY CORD

CLAMP

To pass 2 SAFETY CORDS

through 4 HOLES for safety!

WARNING

CONTROL PANEL

CLAMP

Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers

attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING

on the underside of the base as shown above) To pass the SAFETY CORD through the HOLES for safety! Always ensure

that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure that

you are going to mount the projector to is secure and strong enough to support the weight of the unit.

WARNING:

●The projector MUST be lifted or carried by the HANDLES instead of clamps.

6

●.For safety the safety cord should afford 10 times the Projector’s weight.

● POWER CONNECTION

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that

each projector be connected with power separately so that they may be individually switched on and off.

Note: If projectors are connected in series, please connect POWERIN port of the 1

st

projector with the Power Mains, then

connect its POWER OUT with POWER IN of the 2

nd

projector, and so on till all fixtures are connected. If the voltage

supplied is 200V-240V, the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 8pcs. The diameter

of the cores of the wires for the Power in/out cables must be equal or bigger than 2.5mm

2 .

●The earth wire(yellow/green) must be connected to the ground. And electrical

connection must be in accordance with the standards concerned.

●If any questions about the electrical installation, do not continue but consult a

qualified electrician.

●DMX CONTROL CONNECTION:

Connection between controller and projector and between one projector and another must be made with a twin-screened cable,

with each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included

with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and

sockets mustn’t be connected in any way other than mentioned in the above figure. The XR330BWS accepts digital control

signals in protocol DMX512 (1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminator as shown in the figure below.

7

DMX IN

DMX OUT

DMX IN

DMX OUT

DMX IN

DMX OUT

TO CONTROLLER

TO TERMINATER

●DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is then

plugged into the output socket on the last projector in the chain. The connections are illustrated below.

2

1

3

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

● ALIGNMENT/INSTALLATION/REPLACEMENT OF A LAMP

Before installation/replacement/alignment of a lamp, disconnect the unit from the power and let it cool first.

Lock Tilt in the figure below and open the lamp cover after its 4 screws are loosened.

After removal of the lamp cover, take out the lamp while the 2 screws at both ends of the lamp are loosened.

Insert a new lamp. Note: while placing a new lamp, do not touch the burner of the lamp with bare hands, otherwise the light

output will be compromised.

Fasten the 4 fast-fit screws after the lamp cover is on

Important: The unit uses high voltage discharge lamp with external igniter( ). While using the lamp, please carefully read

“INSTRUCTIONS” packed with the lamp.

●Don’t touch the internal surface of the reflector and the burner of the lamp with bare hands so as not to

impair the beam output. While lamp’s installation, do not damage the metal wire around the burner.

●Please read "Instructions " enclosed with the lamp

●Do operate the projector while adjusting the lamp

8

5. SETUP AND CONFIGURATION

●FRONT PANEL OPERATION

W-DMX

Projector configuration can be set conveniently via push button and LCD display.

Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the function

menu of the projector, each main menu has its submenus and each submenu has a specific function. For details, please see

the “OPERATION MENU” section.

Rotate the knob clockwise UP or anti- clockwise DOWN if you want to browse through the various Setup Options.

Press button ENTER to save your settings or enter the submenu.

Press button UP or DOWN to change values(plus or minus)

Press button FUNC, it will return to the upper menu. If button FUNC not pressed, the default will show display status

automatically.

Shortcut key: Press UP and DOWN buttons together to invert the screen; Press DOWN and ENTER together to change

between English and Chinese menus.

● DMX START ADDRESS

Each unit must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from

the controller. The unit has 3 DMX modes. There are standard mode ,short mode and extended mode. For example standard

mode has 17channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 018, No. 3 projector’s addres35, No. 4

projector’s address052, and so on.

Launch the projector. Press button ENTER more than 5seconds to unlock panel.

Press button ENTER to display DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm; after powered on next time, the default will be last value saved

Press button FUNC, it will return to the upper menu

.

●DMX WIRELESS CONTROL

The projector has wireless control function with wireless receiver module and antenna for remote control.

The setup of it is below:

1. Enter into the projector’s menu. Select the menu “Config settings” via the bottoms of UP and DOWN

2. Select DMX control Mode---- Wireless First (Note: do not select XLR ONLY),then wireless indication in

the front panel will be on, meaning wireless control function is activated.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it,

Press “Enter” for the menu of Unlink Wireless under the upper level menu of Config Settings .

●STAND-ALONE MODE

9

Operate the projector without connecting with a controller, enable the master mode through the operation panel,

the projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVE MODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the

second fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually

connect the last fixture’s DMX output to a DMX terminator. Set 1

st

projector as the master and others are Slaves.

Start Addresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation

mode can be set accordingly.

After Powered on, the group will run in Master/Slave Mode

DMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT

TO CONTROLLER

TO TERMINATER

6. OPERATION MENU

First Menu Secondary Menu Third Menu Fourth Menu

PR Lighting

PR-6000 Wash

DMX Address=XXX

DMX Address

XXX

Reset

Are You Sure

Config Settings

DMX Mode

(Default: Standard 16 )

Standard 16

Extended 16

Short 8

Lamp Control

(Default: By Control Channel)

Lamp Control

By Control Channel

Lamp Control

By Power On

Lamp Control

By DMX Present

When DMX is Lost

Hold Last Value

Factory Settings

(Press button

DOWN/UP/ENTER at the

same time to enter the

sub-menu)

Fixture type

(WARNING：Never

change the fixture type or

the system will be

damaged!)

Offset Menu

10

Option Settings

Color Positions

(Default: Step)

Color Positions

STEPPED

Color Positions

LINEAR

Pan DMX Invert

(Default: Off)

Pan DMX Invert

OFF

Pan DMX Invert

ON

Tilt DMX Invert

(Default: Off)

Tilt DMX Invert

OFF

Tilt DMX Invert

ON

Pan Tilt Swap

(Default: Off)

Pan Tilt Swap

OFF

Pan Tilt Swap

ON

Dimmer Invert

(Default: Off)

Dimmer Invert

OFF

Dimmer Invert

ON

Zoom Invert

(Default: Off)

Zoom Invert

OFF

Zoom Invert

ON

CMY Invert

(Default: Off)

CMY Invert

OFF

CMY Invert

ON

CTO Invert

(Default: Off)

CTO Invert

ON

CTO Invert

OFF

Defaults

(Default: Off)

Defaults

OFF

Defaults

Restore Defaults

Display Options

Display Mode

Display On Always

Display After Delay

Display Invert

Off

Display Invert

On

Display Dimming

Min

1

2

3

4

5

6

7

8

9

A

B

C

D

E

11

F

Full

Display Contrast XX(1-21)

Display Language

Language=

English

Language=

Chinese

Information

Lamp Hours

XX

Reset Lamp hours

Are you sure

Total Hours XX

Temperature

Display Board

Display Board=

XXX

Driver Board 1

Driver Board1 =

XXX

Driver Board 2

Driver Board2=

XXX

Pan and Tilt Board

Pan and Tilt Board=

XXX

Head Sensor

Head Sensor =

XXX

Software Version

Display Board

System=XXX

Boot=XXX

Driver Board 1

System=XXX

Boot=XXX

Driver Board 2

System=XXX

Boot=XXX

Pan and Tilt Board

Pan Tilt Board

System=XXX

Boot=XXX

View DMX Values

DMX Channel

1=XXX

Electronic SN

Electronic SN=

************

RDM Device Label

ANSI E1.20 RDM

Version 1.0

Pan Encoder

Wiring Normal

Pan Err 0

Count 0

Tilt Encoder

Wiring Normal

Pan Err 0

Count 0

Driver Faults

X Over Temp 0

Y Over Temp 0

X Fault 0

Y Fault 0

12

Test Mode

Factory Setup

OFF

Factory Setup

ON

Self Test

OFF

Self Test

ON

Lamp Manual Control

Lamp Status

S=X C=X

Lamp On/Off

Turn Lamp On

Turn Lamp Off

Wireless Options

Wireless Mode

XLR First

Wireless Mode

Wireless Only

Wireless Mode

XLR Only

Wireless Mode

Wireless to XLR

Wireless Mode

Wireless Only

Un-Link Wireless

Really Un-Link

Enter=Yes

Operation Mode

DMX Operation

Master Mode

Select Memory

User Memory1-2

Slave Mode

Select Memory

User Memory1

-

2

Static Scene

User Memories

Edit User Memory

User Memory1-2 Scene 1-200

Shutter XX

Dimmer

XX

Dimmer

Low

XX

CMY

Macro

XX

Cyan XX

Yellow XX

Magenta

XX

CTO XX

Color

Wheel

1

XX

Color

Wheel2

XX

Zoom XX

Pan Coarse

XX

Pan Fine

XX

Tilt Coarse

XX

Tilt Fine

XX

M-Speed

XX

Delay

0.25s~

100s

Link to

Step

XX

Static Scene

Shutter XX

Dimmer XX

13

Dimmer Low

XX

CMY Macro

XX

Cyan XX

Yellow XX

Magenta XX

CTO XX

Color Wheel1

XX

Color Wheel2

XX

Zoom XX

Pan Coarse

XX

Pan Fine XX

Tilt Coarse

XX

Tilt Fine XX

M-Speed XX

Init User Memory

Reset User1

Unlock 2 3 4

Reset User2

Unlock 2 3 4

Reset Static Scene

Reset Static

Scene

Unlock 2 3 4

Note:

1. The parameters transmitted from the mater if multiple units are synchronized include: DMX channel mode ,Display

setting, operation mode including user memory

2. The unit which receives the parameters sent is automatically set as the Slave

7. DMX PROTOCOL

Short

Mode

Standard

Mode

Extended

mode

Function DMX Description

1 1 1

Strobe

000-010 Close

011-025 Open

026-225 Strobe from slow to fast

226-246 Strobe Macro

247-255 Open

2 2 2 Dimmer

000-003 Close

004-255 Linear Dimming （0-100%）

3 3 Dimmer Fine 000-255 Dimmer in 16 Bit

3 4 4 CYM Macro

000

-

016

White

017

-

035

Yellow

＋

Magenta

＝

Red

036

-

054

Yellow

055

-

073

Yellow

＋

Cyan

＝

Green

074

-

092

Cyan

093

-

110

Cyan

＋

Magenta

＝

Purple

111

-

128

Magenta

129

-

255

CYM

color mixing from slow to fast

4 5 5 CYM-Cyan 000-255 Cyan Linear adjustment (0%-100%)

6 CYM-Cyan Fine

000-255 Cyan in 16 Bit

14

5 6 7 CYM-Yellow 000-255 Yellow Linear adjustment (0%-100%)

8

CYM-Yellow

Fine

000-255 Yellow in 16 Bit

6 7 9 CYM-Magenta

000-255 Magenta Linear adjustment (0%-100%)

10

CYM-Magenta

Fine

000-255 Magenta in 16 Bit

7 8 11 CTO

000-255

CTO Linear adjustment from low to

high

12 CTO Fine

000

-

255

CTO in 16 Bit

8 9 13

Colour Wheel1

000-008 White

009-015 White/ Red

016-023 Red

024-030 Red / Yellow

031-038 Yellow

039-045 Yellow / Blue

046-053 Blue

054-060 Blue / Green

061-068 Green

069-075 Green / Pink

076-083 Pink

084-090 Pink / Orange

091-098 Orange

099-105 Orange / UV

106-113 UV

114-120 UV /white

121-127 White

128-191

Forward Rainbow effect from slow to

fast

192-255

Reverse Rainbow effect from slow

to fast

9 10 14

Colour Wheel2

000

-

008

White

009

-

015

White/ Dark Red

016

-

023

Dark Red

024-030 Dark Red / Dark Magenta

031

-

038

Dark Magenta

039

-

045

Dark Magenta / Light Magenta

046

-

053

Light Magenta

054-060 Light Magenta / Light Yellow

061

-

068

Light Yellow

069

-

075

Light Yellow / Light Green

076

-

083

Light Green

084-090 Light Green / Dark Cyan

091

-

098

Dark Cyan

099

-

105

Dark Cyan / Light Cyan

106

-

113

Light Cyan

114-120 Light Cyan /white

121-127 White

15

128-191

Forward Rainbow effect from slow to

fast

192-255

Reverse Rainbow effect from slow

to fast

10 11 15 Zoom 000-255 Linear Zooming

16

Zoom Fine

000

-

255

Zooming in 16 bit

11

12

17

Pan

000

-

255

Pan Rotation

13

18

Pan Fine

0

00

-

255

Tilt in 16 Bit

12 14 19 Tilt 000-255 Tilt Rotation

15

20

Tilt Fine

000

-

255

Tilt in 16 Bit

16 21

Pan & Tilt

speed

000-255 Pan & Tilt Speeds from fast to slow

13 17 22 Control

000-047 Reserved

048

-

080

Reset

081

-

112

Reserved

11

3

-

144

Lamp off

（

10

s

）

145-168 Reserved

169

-

200

Decrease Ballast Power

201

-

223

Reserved

224

-

255

Lamp on

Remark:

If you intend to turn on/off the lamp via the last channel of the controller, don’t attempt to push the channel to value 224-255

immediately after turning it off, or push the slide bar to value 224-255 to wait it cooling. Under these 2 circumstances, the lamp

can not be turned on. The right operation is: turn it off---cool down---push the slide bar to turn it on.

8. LED INDICATION

Green

On

DMX signal OK

Off

No DMX signal

Flash

DMX signal error

Blue

On

Wireless signal OK

Off

Not connection to any transmitter

Flash

Lost contact with the transmitter or linking transmitter

9. ERROR MESSAGE

The Fixture can detect any errors during the reset and may show errors below:

Sensor Err S1-M1

Color Wheel Error（Driver Board1# motor1 ）

Sensor Err S2-M1

Color Wheel Error（Driver Board2 #motor1 ）

Sensor Err S1-M2

CTO error （Driver Board1 motor2）

Sensor Err S1-M3

Cyan Error（Driver Board1 motor3）

16

Sensor Err S1-M4

Yellow Error（Driver Board1 motor4）

Sensor Err S1-M5

Magenta Error（Driver Board1 motor5）

Sensor Err S2-M4

Zoom Error（Driver Board2# motor4）

10. TECHNICAL DATA

INPUT VOLTAGES

200V/220V/230V/240V AC, 50/60Hz

RATED POWER

If 2000w lamp selected with ballast and igniter,rated power:2300W@220V

If 1500wlamp selected with ballast and igniter,rated power:1800W@220V

If 1400wlamp selected with ballast and igniter,rated power:1700W@220V

Power factor: PF>0.9

The specifications of the optional 2000W light source(with 2000W ballast and igniter)

PHILIPS MSR GOLD

TM

2000/1 FastFit

Color Temperature

CRI

Lamp Socket

5800K

97

PGJX50, single ended

Manufacturers Rated Lamp Life 750 hrs

The specifications of the optional 1500W light source(with 1500W ballast and igniter)

OSRAM HTI 1500W/60/P50

Color Temperature 5800K

CRI 90

Lamp Socket PGJX50, single ended

Manufacturers Rated Lamp Life 750 hrs

or

PHILIPS MSR Gold 1500 FastFit

Color Temperature 6000K

CRI 95

Lamp Socket PGJX50, single ended

Manufacturers Rated Lamp Life 750 hrs

The specifications of the optional 1400W light source(with 1400W ballast and igniter)

OSRAM lok-it 1400/PS

Color Temperature 5600K

CRI 90

Lamp Socket single ended

Manufacturers Rated Lamp Life 750 hrs

COLORS

CMY linear mixing system with macros

2 Color wheels: 7colors+ Open, Half Color effect,

17

Rainbow effect with bi-directional and variable speeds,

Stepping/Linear color changing

Color Wheel 1

colo r 1

co lo r 2

co lo r 3

colo r 4

co lo r 5

co lo r 6

color 7

Color Wheel 2

color 1

color2

colo r 3

colo r 4

color 5

color 6

colo r 7

CTO

0-100% linear CTO

FOCUS

No. Part Number Name Wave Length

1 090070041A

Red

λ=620±5nm

2 090070044A

Yellow

λ=510/545±5nm

3 090070043A

Blue

λ=500±5nm

4 090070042A

Green

λ=540±5nm

5 090070045A

Pink

λ=490/585±5nm

6 090070046A

Orange

λ=600±5nm

7 090070047A

UV

λ=460/690±5nm

No. Part Number Name Wave Length

1 090070034A Dark Red λ=645±5nm

2 090070037A Dark Magenta λ=450/630±5nm

3 090070040A Light Magenta λ=445/620±5nm

4 090070039A Light Yellow λ=520±5nm

5 090070035A Light Green λ=485/525±5nm

6 090070036A Dark Cyan λ=575±5nm

7 090070038A Light Cyan λ=590±5nm

DMX linear adjustment

ZOOM

DMX linear adjustment

DIMMER

0-100% Linear adjustment

STROBE

Double shutter blades, 0.3~25 F.P.S

HEAD MOVEMENT

Pan 540º, Tilt 270º with auto position correction

BEAM ANGLE

Highlight mode: 10°

18

20°～ 68°(16bit adjustment)

CONTROL

DMX512, 3 pins and 5 pins interfaces

RDM control protocol

13 channels in short mode, 17channels in standard mode and 22channels in extended mode

Self-test mode

OTHER FUNCTIONS

Adjustable Pan & Tilt speed

Lamp and Total hours displayed

LCD English and Chinese Display with Contrast and brightness adjustable

Energy saving ballast

Built-in sensor diagnostic system

Built-in Chargeable battery and menu setting without power mains

Input signal isolation

Modular Structure for easy maintenance

Ethernet Interface

DMX512 wireless Receiver

Optional DMX512 Transmitter

HOUSING

High temperature ABS, IP20

NET WEIGHT

45Kg

OPERATION TEMPERATURE

Maximum ambient temperature: 40°C

SIZES:

LIGHT OUTPUT:

19

The light output diagram of 2000W lamp, ballast and igniter

10° D iameter (m )

Distance(m )

0m

5m 10m 15m 20m 25m 30m

0.96

1.92 2.87 3.83

4.79

5.75

0

10°Lux

129644

32411

14405 8103

5186

3601

0

20° D iameter (m )

20° Lux

0

25115

6279

2791

1570

1005

698

1.83

3.66

5.50

7.33 9.16 10.99

0

20°

10°

68°

68° Lux

0

2796

699

311 175

112

78

68° D iameter (m )

5.87

11.74

17.61 23.48

29.34 35.21

0

The light output diagram of 1500W lamp, ballast and igniter

17°DIAMETER（m）

DISTANCE（m） 0m 5m 10m 15m 20m 25m 30m

0

62°DIAMETER（m）

0

17°（lux）

0

62°（lux）

1.55 3.09 4.46 6.18 7.73 9.28

5.39 10.77 16.16 21.55 26.94 32.32

29279 7320 3253 1830

121

84

3035 759 337 190

1171 813

7.5°（lux） 0

219555 54889 24395 13722 8782

6099

7.5°DIAMETER（m）

0 0.69 1.39 2.08 2.77 3.46 4.16

17°

7.5°

62°

The light output diagram of 1400W lamp, ballast and igniter

20

17°DIAMETER（m）

DISTANCE（m）

0m 5m 10m 15m 20m 25m 30m

0

62°DIAMETER（m）

0

17°（lux）

0

62°（lux）

1.55 3.09 4.46 6.18 7.73 9.28

5.39 10.77 16.16 21.55 26.94 32.32

30843 7711 3427 1928

147

102

3664 916 407 229

1234

857

7.5°（lux） 0

193976 48494 21553 12123 7759

5388

7.5°DIAMETER（m）

0 0.69 1.39 2.08 2.77 3.46 4.16

17°

7.5°

62°

Page is loading ...

PR Lighting PR-6000 Wash User manual

PR Lighting PR-6000 Wash User manual

Related papers

Other documents