Beamz WHIRLWIND 3-in-1 LED Effect DMX Quick start guide

Beamz
Brand
Beamz
Model
WHIRLWIND 3-in-1 LED Effect DMX
Type
Quick start guide

Beamz WHIRLWIND 3-in-1 LED Effect DMX is a versatile lighting fixture that combines three effects in one: a beam, a wash, and a laser. With its powerful LEDs, the WHIRLWIND can create a variety of dazzling effects, from sharp beams of light to wide washes of color. It can be controlled via DMX or run in standalone mode, making it suitable for a wide range of applications, from small clubs to large concert halls.

The WHIRLWIND's beam effect features a bright white LED that can be focused to create a tight, narrow beam of light. This beam can be rotated and panned, allowing you to create dynamic effects. The wash effect features a ring of RGB LEDs that can be used to create a wide wash of color. The laser effect features a green laser that can be used to create a variety of laser patterns.

Beamz WHIRLWIND 3-in-1 LED Effect DMX is a versatile lighting fixture that combines three effects in one: a beam, a wash, and a laser. With its powerful LEDs, the WHIRLWIND can create a variety of dazzling effects, from sharp beams of light to wide washes of color. It can be controlled via DMX or run in standalone mode, making it suitable for a wide range of applications, from small clubs to large concert halls.

The WHIRLWIND's beam effect features a bright white LED that can be focused to create a tight, narrow beam of light. This beam can be rotated and panned, allowing you to create dynamic effects. The wash effect features a ring of RGB LEDs that can be used to create a wide wash of color. The laser effect features a green laser that can be used to create a variety of laser patterns.

WHIRLWIND
153.705 V1.1
On the label on the backside of the unit is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all
other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and may be used. No
dimmer or adjustable power supply.
Always connect the unit to a protected circuit (circuit breaker or fuse). Make sure the unit has an appropriate electrical ground to
avoid the risk of electrocution or fire.
If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first unit in a DMX chain.
Always connect the output of one unit with the input of the next unit until all units are connected.
At the last unit, you must close the DMX line with a terminating resistor. Take an XLR connector and solder a 120 Ohm resistor
between signal (-) and signal (+) and connect it to the DMX output of the last unit in the line.
ON
OFF
DMX Mode
Auto Running Mode
Auto Running Speed up
Auto Running Speed down
Sound Control Mode
Sound Sensitive +
Sound Sensitive -
DMX address setting
Internal program 1-9
Auto program
Internal sound program
Sound program, 1-9 means sensitive
1
PAN Rotation
0-360degrees movement
2
PAN Rotation endless
No function
Pan forward rotate from slow to fast
Pan reverse rotate from fast to slow
3
Dimmer
Linear dimmer from dark to brighter
4
Strobe
No function
Strobe from slow to fast
5
Gobo Colour
Red dimmer from dark to brighter
6
Green dimmer from dark to brighter
7
Blue dimmer from dark to brighter
8
White dimmer from dark to brighter
9
Line Colour
Red dimmer from dark to brighter
10
Green dimmer from dark to brighter
11
Blue dimmer from dark to brighter
12
White dimmer from dark to brighter
13
Ball Colour
Red dimmer from dark to brighter
14
Green dimmer from dark to brighter
15
Blue dimmer from dark to brighter
16
White dimmer from dark to brighter
17
Mode
CH1-CH16 Valid
Random Auto Running
Sound Control
18
Reset
None
Reset after 3s
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Beamz WHIRLWIND 3-in-1 LED Effect DMX Quick start guide

Beamz
Brand
Beamz
Model
WHIRLWIND 3-in-1 LED Effect DMX
Type
Quick start guide

Beamz WHIRLWIND 3-in-1 LED Effect DMX is a versatile lighting fixture that combines three effects in one: a beam, a wash, and a laser. With its powerful LEDs, the WHIRLWIND can create a variety of dazzling effects, from sharp beams of light to wide washes of color. It can be controlled via DMX or run in standalone mode, making it suitable for a wide range of applications, from small clubs to large concert halls.

The WHIRLWIND's beam effect features a bright white LED that can be focused to create a tight, narrow beam of light. This beam can be rotated and panned, allowing you to create dynamic effects. The wash effect features a ring of RGB LEDs that can be used to create a wide wash of color. The laser effect features a green laser that can be used to create a variety of laser patterns.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents