PROLINK PRO1911W User manual

Brand: PROLINK

Model: PRO1911W

Category: Monitors CRT

Type: User manual

This manual is also suitable for

PRO2211W

USER'S MANUAL

PROLiNK LCD MONITOR

PRO1911W & PRO2211W

Version 1.2 (Feb’09)

your

Global

Communications

Info

Provider

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) i

TABLE OF CONTENTS

FCC Statement 1

Important Safeguard 2

Chapter 1 Introduction 3

1.1 Features 3

1.2 Checking List 3

Chapter 2 Monitor Overview 4

2.1 Front Panel overview 4

2.2 Rear Panel overview 5

Chapter 3 Installation 6

3.1 Connecting a Computer 6

3.2 Connecting a Laptop 6

3.3 Connect with Audio 6

Chapter 4 Operation 7

4.1 Power (ON/OFF) Switch Button 7

4.2 Power LED/Indicator 7

4.3 Auto 7

4.4 Menu Features 7

4.5 OSD Menu 7

Chapter 5 Technical Information 11

5.1 Product Specifications 11

5.2 Troubleshooting 11

Chapter 6 Technical Support 13

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 1

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

1. Re-orientate or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4. Consult the dealer or an experienced radio/TV technician for help.

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 2

Important Safeguard

1. Read all of these instructions.

2. Unplug this monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

3. Do not use this monitor near water. For example near a bathtub, washbowl , kitchen sink, or

laundry tub, in a wet basement , or near a swimming pool, etc…

4. Do not place this monitor on an unstable cart, stand, or table. The monitor may fall, causing

serious injury to a child or adult, and serious damage to the appliance. Use only with a cart or

stand recommended by the manufacturer or sold with monitor. Only use mounting kit(s) that are

approved by the manufacturer. Any wall or shelf mounting are to be done in accordance to the

instructions set by the manufacturer.

5. Slots and openings in the cabinet such as the back or bottom should be provided for ventilation.

To insure reliable operation of the television receiver and to protect it from overheating, these

openings must not be blocked or covered. The openings should never be blocked by placing the

monitor on a bed, sofa, rug or any other similar surface. This monitor should also not be placed

in a bookcase unless proper ventilation is provided.

6. Do not allow anything to rest on the power cord. Do not position this monitor where the cord will

be susceptible to damage.

7. Do not insert any objects into this monitor through cabinet slots as they may hit dangerous

voltage points or damage mechanical parts that could result in permanent damage or electric

shock. Never spill liquid of any kind onto the monitor.

8. Do not attempt to service this monitor yourself since opening or removing covers may expose

you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

9. Unplug this monitor from the wall outlet and refer servicing to qualified service personnel under

the following :

a) When the power cord or plug is damaged or frayed.

b) If liquid has been spilled onto the monitor.

c) If the monitor has been exposed to rain or water.

d) If the monitor has been dropped or the cabinet has been damaged.

e) When the monitor exhibits a distinct change in performance. This indicates the need for

servicing.

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 3

Chapter 1 Introduction

1.1 Features

9 High resolution of 1440 × 900 @ 60Hz (for PRO1911W), 1680 × 1050 @ 60Hz (for

PRO2211W)

9 Contrast ratio of 5000 : 1 (for PRO1911W), 10000 : 1 (for PRO2211W)

9 0.28mm Pixel Pitch

9 Response time of 2ms (milliseconds)

9 Brightness of 300 cd/m2

9 16.7M high quality image color

9 Microprocessor based with OSD (On Screen Display) control.

9 Compatible with standard IBM VGA, extended VGA, super VGA, IBM XGA modes, as well

as VESA resolution standards.

9 Universal Power Supply.

9 Microsoft Windows 9x/2000/XP compatible & VESA Display Data Channel (DDC) 1/2B

compatible.

9 Save spaces as monitor is slim in design.

9 Power saving.

9 Smart model image screen setting

9 Auto function which will automatically adjust the signal to the best settings.

1.2 Checking Lists

Please make sure the following items are included with your LCD monitor:

9 Monitor 9 User Manual

9 AC power cord 9 Audio cable

9 Signal cable 9 DVI signal cord (Optional)

If any of these items are missing, please contact your dealer for technical support.

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 4

Chapter 2 Monitor Overview

2.1 Front Panel overview

OSD Main Menu

Up button

Down button

Exit button

Power LED/Indicator

Power button

19” for

PRO1911W

22” for

PRO2211W

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 5

2.2 Front Panel overview

VGA

Connector

DVI

Connector

Audio

Connector

Note:

For VOLUME function, please ensure the audio is connected to the sound card of the computer or

to the output source of any media player with 3.5mm stereo socket.

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 6

Chapter 3 Installation

Whenever you connect a video system to your set, ensure that all elements are switched off. Refer to

the documentation supplied with your equipment for a detailed connection instructions and safeguard

information.

3.1 Connecting a Computer

3.1.1 Unplug or disconnect the signal cord connector from your existing PC video connector

and LCD/CRT Monitor, IF ANY,

3.1.2 Plug in or connect the signal cord connector to the PC video connector,

3.1.3 Plug in or connect the power cord to the LCD Monitor, and

3.1.4 Turn power plug socket switch ON to supply voltage to both PC and Monitor,

3.1.5 Turn power button switch ON for both PC and Monitor,

3.1.6 For most OS, Monitor is Plug & Play without driver installation required.

3.2 Connecting a Laptop

Ensure the Laptop comes with a video output connector, then follow the procedures stated

below:

3.2.1 Unplug or disconnect the signal cord connector from your existing PC video connector

and LCD/CRT Monitor, IF ANY,

3.2.2 Plug in or connect the signal cord connector to the Laptop's video output connector,

3.2.3 Plug in or connect the power cord to the LCD Monitor, and

3.2.4 Turn power plug socket switch ON to supply voltage to both PC and Monitor,

3.2.5 Turn power button switch ON for both Laptop and Monitor,

3.2.6 Press video output button from Laptop with special key combination (different

combination in various type of laptop).

3.3 Connecting an Audio

3.3.1 Connect the stereo audio cable to the “PC AUDIO IN(STEREO)” jack to the rear of your

LCD monitor and the other end to the “Audio Out” jack of the sound card on your

computer.

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 7

Chapter 4 Operation

4.1 Power (ON/OFF) Switch Button

This button is used to turn the monitor on and off.

NOTE: The ON/OFF switch button does not disconnect the device from the main voltage. To

completely disconnect the main voltage, please remove the power plug from the socket.

4.2 Power LED/Indicator

GREEN lights indicate that the monitor operates normally.

Blinking GREEN lights indicate that there is no input signal from computer.

DARK (no lights) indicates that the monitor is turned off.

4.3 Auto

Press AUTO button and release, the auto adjust display mode will tune to the utmost

performance according to VGA settings.

4.4 Menu Features

The following features can be accessed using monitor on screen menu system.

Press  button to move menu selection up or adjust increasing.

Press  button to move menu selection down or adjust decreasing.

Press MENU button to confirm selection or setting.

Press EXIT button to go back to previous menu, or exit from the screen menu system.

4.5 OSD Menu

Main Menu

OSD Main Menu gives user an overview of the selection of controls available. When the user

wants to adjust the screen image, the user will press and release the Menu button.

The OSD Main Menu consists of:

1. Color Adjustment

2. Image Adjustment

3. Color Temperature Adjustment

4. OSD Tools

5. Language

6. Misc

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 8

1. Color Adjustment

1.1 Brightness adjustment

To adjust the image brightness to suit the user viewing requirements.

1.2 Contrast adjustment

To adjust the image contrast to obtain the best display on screen.

1.3 DCR Mode (option)

To select DCR ON or OFF

2. Image Adjustment

2.1 Horizontal position adjustment

To move the picture image horizontally left or right.

2.2 Vertical position adjustment

To move the picture image vertically up or down.

2.3 Phase adjustment

To improve focus clarity an image stability.

2.4 Clock adjustment

To increase or decrease the horizontal size of image.

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 9

3. Color Temperature Adjustment

3.1 Warm

This control adjusts the color temperature of the screen image, preset by default.

3.2 Cool

This control adjusts the color temperature of the screen image, preset by default.

3.3 User

Increase or decrease red, green or blue depending on user viewing requirements.

4. OSD Tools

4.1 OSD Horizontal Position

To move the OSD image horizontally left or right.

4.2 OSD Vertical Position

To move the OSD image vertically up or down.

5. Language

Various type of OSD languages available as:

9 English 9 Italian

9 Spanish 9 German

9 French 9 Chinese

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 10

6. Misc

6.1 Auto Configuration

To automatically get the best adjustment.

Not function with DVI signal.

6.2 Auto Color

To automatically get the best color adjustment.

Not function with DVI signal.

6.3 Factory Reset

To reset all setting back to factory default settings.

Not function with DVI signal.

6.4 Volume

To adjust monitor volume.

6.5 Image Ratio (Optional)

Select between 16:9 and 4:3

6.6 Signal Source (Optional)

Select between PC-VGA and PC-DVI (Optional)

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 11

Chapter 5 Technical Information

5.1 Product Specifications

ITEM DESCRIPTION

Model Number PRO1911W 19" LCD Monitor PRO2211W 22" LCD Monitor

Bezel color Options Black Full black or Full Silver

TFT Panel 16:10 16:10

Pixel Pitch (mm) 0.28 0.28

View Angle H: 150˚ V: 135˚ H:160˚ V:160˚

Resolution (Typical) 1440 × 900 @ 60Hz 1680 × 1050 @ 60Hz

Contrast Ratio (max) 5000:1 10000:1

Brightness 300 cd/m2 300 cd/m2

Response Time 2ms 2ms

Color 16.7M 16.7M

OSD Language En

lish, German, French, Italian,

Spanish, Chinese

lish, German, French, Italian,

Spanish, Chinese

Speaker With speaker (2W × 2) With speaker (2W × 2)

DVI Optional Optional

Power Input 100~240V, 50/60Hz 100~240V, 50/60Hz

Power Consumption (max) 40 W 50 W

Certification CE, CB, FCC CE

Packing Dimension (mm) Subject to Changes Subject to Changes

Weight (kg) 5.3KG/6.5KG 5.0KG/7.0KG

5.2 Troubleshooting

Before calling for service, check the information in this section to see if you can remedy any

problems. Should you require any further assistance, please contact the dealer from whom you

purchased the LCD monitor.

5.3.1 There is no SCREEN image

 Check if the power cord is securely connected to the monitor, the adapter and the

wall outlet.

 Check if the signal cable is connected between the monitor and the computer.

 Check if the monitor is in power saving mode.

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 12

5.3.2 Display image is too large or small

 Use the OSD controls to adjust Auto Setup.

5.3.3 The color are distorted

 Check if the signal cable is properly connected.

 Use the OSD controls to adjust the color control setting.

5.3.4 The image is too light or too dark

 Use the OSD controls to adjust the brightness and contrast.

5.3.5 There is no sound or sound is low

 Check the sound cable connection.

 Make sure the computer sound program is working.

 Adjust the volume on sound setting. Adjust your sound card or computer volume

setting.

 Adjust the volume control keys on the monitor.

5.3.6 The screen appearing up and down H-rolling scan

 Make sure the view of input signal is within the order of the monitor (60Hz –

75Hz)

5.3.7 How to clean the monitor

 Make sure monitor is turn off.

 Do not spray any liquid on the screen.

 Use clean, soft and no fur cloth to clean the monitor screen.

 A little non-ammonia liquid and non-alcohol glass cleaner is allowed to be used for

cleaning.

5.3.8 How to clean the cabinet

 Use soft dry cloth

 A little non-ammonia liquid and non-alcohol of non-abrasion cleanser is allowed to

use for cleaning the surface.

PROLiNK User's Manual for PRO1911W, PRO2211W www.prolink2u.com

Version 1.2 (Feb’09) 13

Chapter 6 Technical Support

FREE TECHNICAL SUPPORT HOTLINE:

Mon to Fri: 9am - 6pm

(Closed on Sundays & Public Holidays)

• Singapore : (65) 6357 0666

• Malaysia : (60) 3 8023 9151

• Indonesia : (62) 21 628 3205

WALK-IN:

Mon to Fri: 9am - 6pm

(Closed on Saturdays , Sundays & Public Holidays)

Singapore

FIDA INTERNATIONAL (S) PTE LTD

Blk 16 Kallang Place #06-02

Kallang Basin Industrial Estate Singapore 339156

Malaysia

FIDA SYSTEMS (M) SDN BHD

29 USJ 1/31, 47600 Subang Jaya Selangor,

Darul Ehsan, Malaysia

Indonesia

PROLiNK INDONESIA

P.Jayakarta Komplek 85 BR/AJ, Jakarta Pusat, Indonesia

ONLINE TECHNICAL SUPPORT:

[email protected]

Version 1.2 (Feb’09) 14

www.prolink2u.com

Singapore

FIDA INTERNATIONAL (S) PTE LTD

Blk 16 Kallang Place #06-02

Kallang Basin Industrial Estate Singapore 339156

Email: [email protected]

Malaysia

FIDA SYSTEMS (M) SDN BHD

Tel: (60) 3 8023 9151

Indonesia

PROLINK INDONESIA

Tel: (62) 21 628 3205

PROLiNK is manufactured under the authority of FIDA INTERNATIONAL (S) PTE LTD

PROLINK PRO1911W User manual

Brand: PROLINK

Model: PRO1911W

Category: Monitors CRT

Type: User manual

This manual is also suitable for

PRO2211W

Download PDF

report

PROLINK PRO1911W User manual

This manual is also suitable for

PROLINK PRO1911W User manual

Related papers

Other documents