PROLINK PRO2212W User manual
- Category
- Monitors CRT
- Type
- User manual
This manual is also suitable for
PROLiNK PRO1912W, PRO2012W, PRO2212W User's Manual www.prolink2u.com
Version 1.2 (Feb’09) i
TABLE OF CONTENTS
FCC Statement 1
Important Safeguard 2
Chapter 1 Introduction 3
1.1 Features 3
1.2 Checking List 3
Chapter 2 Monitor Overview 4
2.1 Front Panel overview 4
2.2 Rear Panel overview 5
Chapter 3 Installation 6
3.1 Connecting a Computer 6
3.2 Connecting a Laptop 6
3.3 Connect with Audio 6
Chapter 4 Operation 7
4.1 Power (ON/OFF) Switch Button 7
4.2 Power LED/Indicator 7
4.3 Auto 7
4.4 Menu Features 7
4.5 OSD Menu 7
Chapter 5 Technical Information 11
5.1 Product Specifications 11
5.2 Troubleshooting 11
Chapter 6 Technical Support 13
PROLiNK PRO1912W, PRO2012W, PRO2212W User's Manual www.prolink2u.com
Version 1.3 (Aug’09) 1
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
1. Re-orientate or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/TV technician for help.
PROLiNK PRO1912W, PRO2012W, PRO2212W User's Manual www.prolink2u.com
Version 1.3 (Aug’09) 2
Important Safeguard
1. Read all of these instructions.
2. Unplug this monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
3. Do not use this monitor near water. For example near a bathtub, washbowl , kitchen sink, or
laundry tub, in a wet basement , or near a swimming pool, etc…
4. Do not place this monitor on an unstable cart, stand, or table. The monitor may fall, causing
serious injury to a child or adult, and serious damage to the appliance. Use only with a cart or
stand recommended by the manufacturer or sold with monitor. Only use mounting kit(s) that are
approved by the manufacturer. Any wall or shelf mounting are to be done in accordance to the
instructions set by the manufacturer.
5. Slots and openings in the cabinet such as the back or bottom should be provided for ventilation.
To insure reliable operation of the television receiver and to protect it from overheating, these
openings must not be blocked or covered. The openings should never be blocked by placing the
monitor on a bed, sofa, rug or any other similar surface. This monitor should also not be placed
in a bookcase unless proper ventilation is provided.
6. Do not allow anything to rest on the power cord. Do not position this monitor where the cord will
be susceptible to damage.
7. Do not insert any objects into this monitor through cabinet slots as they may hit dangerous
voltage points or damage mechanical parts that could result in permanent damage or electric
shock. Never spill liquid of any kind onto the monitor.
8. Do not attempt to service this monitor yourself since opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
9. Unplug this monitor from the wall outlet and refer servicing to qualified service personnel under
the following :
a) When the power cord or plug is damaged or frayed.
b) If liquid has been spilled onto the monitor.
c) If the monitor has been exposed to rain or water.
d) If the monitor has been dropped or the cabinet has been damaged.
e) When the monitor exhibits a distinct change in performance. This indicates the need for
servicing.
PROLiNK PRO1912W, PRO2012W, PRO2212W User's Manual www.prolink2u.com
Version 1.3 (Aug’09) 3
Chapter 1 Introduction
1.1 Features
9 High resolution of 1360 x 768 @ 60Hz (for PRO1912W), 1600x900 @ 60 (for PRO2012W)
1920 x 1080 @ 60Hz (for PRO2212W)
9 Contrast ratio of 10000:1
9 Pixel pitch of 0.3mm (for PRO1912W), 0.276mm (for PRO2012W) and 0.248mm (for
PRO2212W)
9 Response time of 2ms
9 Brightness of 300cd/m2
9 16.7M high quality image colors
9 Smart image screen setting –OSD with simple layout and easy selection
9 Universal Power Supply
9 Save spaces as monitor is slim in design
9 Power Saving
9 Smart control interfaces for easy settings
9 Auto Function which will automatically adjust the signal to the best settings
1.2 Checking Lists
Please make sure the following items are included with your LCD monitor:
9 Monitor 9 User Manual
9 AC power cord 9 Audio cable (Optional)
9 Signal cable 9 DVI signal cord (Optional)
9 Wall mount (optional)
If any of these items are missing, please contact your dealer for technical support.
PROLiNK PRO1912W, PRO2012W, PRO2212W User's Manual www.prolink2u.com
Version 1.3 (Aug’09) 5
2.2 Front Panel overview
VGA
Connector
DVI
Connector
Audio
Connector
Note:
For VOLUME function, please ensure the audio is connected to the sound card of the computer or
to the output source of any media player with 3.5mm stereo socket.
PROLiNK PRO1912W, PRO2012W, PRO2212W User's Manual www.prolink2u.com
Version 1.3 (Aug’09) 6
Chapter 3 Installation
Whenever you connect a video system to your set, ensure that all elements are switched off. Refer to
the documentation supplied with your equipment for a detailed connection instructions and safeguard
information.
3.1 Connecting a Computer
3.1.1 Unplug or disconnect the signal cord connector from your existing PC video connector
and LCD/CRT Monitor, IF ANY,
3.1.2 Plug in or connect the signal cord connector to the PC video connector,
3.1.3 Plug in or connect the power cord to the LCD Monitor, and
3.1.4 Turn power plug socket switch ON to supply voltage to both PC and Monitor,
3.1.5 Turn power button switch ON for both PC and Monitor,
3.1.6 For most OS, Monitor is Plug & Play without driver installation required.
3.2 Connecting a Laptop
Ensure the Laptop comes with a video output connector, then follow the procedures stated
below:
3.2.1 Unplug or disconnect the signal cord connector from your existing PC video connector
and LCD/CRT Monitor, IF ANY,
3.2.2 Plug in or connect the signal cord connector to the Laptop's video output connector,
3.2.3 Plug in or connect the power cord to the LCD Monitor, and
3.2.4 Turn power plug socket switch ON to supply voltage to both PC and Monitor,
3.2.5 Turn power button switch ON for both Laptop and Monitor,
3.2.6 Press video output button from Laptop with special key combination (different
combination in various type of laptop).
3.3 Connecting an Audio
3.3.1 Connect the stereo audio cable to the “PC AUDIO IN(STEREO)” jack to the rear of your
LCD monitor and the other end to the “Audio Out” jack of the sound card on your
computer.
PROLiNK PRO1912W, PRO2012W, PRO2212W User's Manual www.prolink2u.com
Version 1.3 (Aug’09) 7
Chapter 4 Operation
4.1 Power (ON/OFF) Switch Button
This button is used to turn the monitor on and off.
NOTE: The ON/OFF switch button does not disconnect the device from the main voltage. To
completely disconnect the main voltage, please remove the power plug from the socket.
4.2 Power LED/Indicator
GREEN lights indicate that the monitor operates normally.
Blinking GREEN lights indicate that there is no input signal from computer.
DARK (no lights) indicates that the monitor is turned off.
4.3 Auto
Press AUTO button and release, the auto adjust display mode will tune to the utmost
performance according to VGA settings.
4.4 Menu Features
The following features can be accessed using monitor on screen menu system.
Press button to move menu selection up or adjust increasing.
Press button to move menu selection down or adjust decreasing.
Press MENU button to confirm selection or setting.
Press EXIT button to go back to previous menu, or exit from the screen menu system.
4.5 OSD Menu
Main Menu
OSD Main Menu gives user an overview of the selection of controls available. When the user
wants to adjust the screen image, the user will press and release the Menu button.
The OSD Main Menu consists of:
1. Color Adjustment
2. Image Adjustment
3. Color Temperature Adjustment
4. OSD Tools
5. Language
6. Misc
1920 x 1080@60Hz
PROLiNK PRO1912W, PRO2012W, PRO2212W User's Manual www.prolink2u.com
Version 1.3 (Aug’09) 8
1. Color Adjustment
1.1 Brightness adjustment
To adjust the image brightness to suit the user viewing requirements.
1.2 Contrast adjustment
To adjust the image contrast to obtain the best display on screen.
1.3 DCR Mode (option)
To sel ec t D CR ON o r OF F
2. Image Adjustment
2.1 Horizontal position adjustment
To move the picture image horizontally left or right.
2.2 Vertical position adjustment
To move the picture image vertically up or down.
2.3 Phase adjustment
To improve focus clarity an image stability.
2.4 Clock adjustment
To increase or decrease the horizontal size of image.
1920 x 1080@60Hz
1920 x 1080@60Hz
PROLiNK PRO1912W, PRO2012W, PRO2212W User's Manual www.prolink2u.com
Version 1.3 (Aug’09) 9
3. Color Temperature Adjustment
3.1 Warm
This control adjusts the color temperature of the screen image, preset by default.
3.2 Cool
This control adjusts the color temperature of the screen image, preset by default.
3.3 User
Increase or decrease red, green or blue depending on user viewing requirements.
4. OSD Tools
4.1 OSD Horizontal Position
To move the OSD image horizontally left or right.
4.2 OSD Vertical Position
To move the OSD image vertically up or down.
5. Language
Various type of OSD languages available as:
9 English 9 Italian
9 Spanish 9 German
9 French 9 Chinese
1920 x 1080@60Hz
1920 x 1080@60Hz
PROLiNK PRO1912W, PRO2012W, PRO2212W User's Manual www.prolink2u.com
Version 1.3 (Aug’09) 10
6. Misc
6.1 Auto Configuration
To automatically get the best adjustment.
Not function with DVI signal.
6.2 Auto Color
To automatically get the best color adjustment.
Not function with DVI signal.
6.3 Factory Reset
To reset all setting back to factory default settings.
Not function with DVI signal.
6.4 Volume
To a dj us t monitor volum e.
6.5 Image Ratio (Optional)
Select between 16:9 and 4:3
6.6 Signal Source (Optional)
Select between PC-VGA and PC-DVI (Optional)
PROLiNK PRO1912W, PRO2012W, PRO2212W User's Manual www.prolink2u.com
Version 1.3 (Aug’09) 11
Chapter 5 Technical Information
5.1 Product Specifications
ITEM DESCRIPTION
Model Number PRO1912W 18.5” PRO2012W 20” PRO2212W 21.6”
Bezel color Options Piano Black Piano Black Piano Black
TFT Panel (16:9) Wide (16:9) Wide (16:9) Wide
Pixel Pitch (mm) 0.3mm 0.276mm 0.248mm
View Angle H:160° V:160° H:80° V:85° H:160° V:160°
Resolution (Typical) 1360 x 768 @ 60Hz 1600 x 900 @ 60Hz 1920 x 1080 @ 60Hz
Contrast Ratio (max) 10000:1 (DCR) 10000:1 (DCR) 10000:1 (DCR)
Brightness 300cd/m² 300cd/m² 300cd/m²
Response Time 2ms 2ms 2ms
Color 16.7M 16.7M 16.7M
OSD Language
English, German,
French, Italian, Spanish,
Chinese
English, German,
French, Italian, Spanish,
Chinese
English, German,
French, Italian, Spanish,
Chinese
Speaker With Speaker (2W x 2) Optional With Speaker (2W x 2)
DVI With DVI With DVI With DVI
Power Input 100~240V, 50/60Hz 100~240V, 50/60Hz 100~240V, 50/60Hz
Power Consumption(Max) 40 W 40 W 50 W
Certification CE, FCC, ROHS CE, FCC, ROHS CE, FCC, ROHS
Packing Dimension (mm) 503 x 392 x 114 532 x 425 x 212.5 577 x 452 x 132
Nett/Gross Weight (kg) 3.2/4.4kg 3.4/5.0kg 4/5.5kg
5.2 Troubleshooting
Before calling for service, check the information in this section to see if you can remedy any
problems. Should you require any further assistance, please contact the dealer from whom you
purchased the LCD monitor.
5.3.1 There is no SCREEN image
Check if the power cord is securely connected to the monitor, the adapter and the
wall outlet.
Check if the signal cable is connected between the monitor and the computer.
Check if the monitor is in power saving mode.
5.3.2 Display image is too large or small
Use the OSD controls to adjust Auto Setup.
5.3.3 The color are distorted
Check if the signal cable is properly connected.
Use the OSD controls to adjust the color control setting.
5.3.4 The image is too light or too dark
Use the OSD controls to adjust the brightness and contrast.
5.3.5 There is no sound or sound is low
Check the sound cable connection.
Make sure the computer sound program is working.
Adjust the volume on sound setting. Adjust your sound card or computer volume
setting.
Adjust the volume control keys on the monitor.
5.3.6 The screen appearing up and down H-rolling scan
Make sure the view of input signal is within the order of the monitor (60Hz –
75Hz)
5.3.7 How to clean the monitor
Make sure monitor is turn off.
Do not spray any liquid on the screen.
Use clean, soft and no fur cloth to clean the monitor screen.
A little non-ammonia liquid and non-alcohol glass cleaner is allowed to be used for
cleaning.
5.3.8 How to clean the cabinet
Use soft dry cloth
A little non-ammonia liquid and non-alcohol of non-abrasion cleanser is allowed to
use for cleaning the surface.
PROLiNK PRO1912W, PRO2012W, PRO2212W User's Manual www.prolink2u.com
Version 1.3 (Aug’09) 13
Chapter 6 Technical Support
REGISTER ONLINE FOR FREE WARRANTY.
FREE TECHNICAL SUPPORT HOTLINE:
Monday to Friday, 9.00 am – 6.00 pm
(Closed on Saturdays, Sundays and Public Holidays)
• Singapore : (65) 6357 0666
• Malaysia : (60) 3 8023 9151
• Indonesia : (62) 21 628 3205
WALK-IN SUPPORT:
Monday to Friday, 9.00 am – 6.00 pm
(Closed on Saturdays, Sundays and Public Holidays)
• Singapore
FIDA INTERNATIONAL (S) PTE LTD
Block 16 Kallang Place, #06-02 Kallang Basin Industrial Estate, Singapore 339156.
• Malaysia
FIDA SYSTEMS (M) SDN BHD
29 Jalan USJ 1/31, 47600 Subang Jaya, Selangor Darul Ehsan, Malaysia.
• Indonesia
PROLiNK INDONESIA
P. Jayakarta Komplek 85 BR/AJ, Jakarta Pusat - Indonesia.
ONLINE TECHNICAL SUPPORT:
• Singapore : support@fida.com
• Malaysia : support_my@fida.com
• Indonesia : [email protected]
PROLiNK is a trademark of Fida International (S) Pte Ltd and is manufactured under its authority. All other brands,
products, services, logos and company names mentioned herein are trademarks of their respective owners. All
specifications, designs and contents are subject to changes without prior notice. © Copyright 2009. PROLiNK all
rights reserved.
Register Online For Your Product Warranty
www.prolink2u.com
SINGAPORE
FIDA INTERNATIONAL (S) PTE LTD
Block 16 Kallang Place, #06-02 Kallang Basin Industrial Estate, Singapore 339156.
Tel : (65) 6357 0668 Email : support@fida.com
MALAYSIA
FIDA SYSTEMS (M) SDN BHD
29 Jalan USJ 1/31, 47600 Subang Jaya, Selangor Darul Ehsan, Malaysia.
Tel : (60) 3 8024 9151 Email : support_my@fida.com
INDONESIA
PROLiNK INDONESIA
P. Jayakarta Komplek 85 BR/AJ, Jakarta Pusat - Indonesia.
Tel : (62) 21 628 3205 Email : [email protected]
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
PROLINK PRO2212W User manual
- Category
- Monitors CRT
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
PROLINK PRO1911W User manual
-
-
PROLINK PWP102G User manual
-
-
-
-
-
-
-