Page is loading ...
Quick Installation Guide
Portable 4G LTE
WiFi Hotspot
MODEL NO:
PRT7010L
Version 1.00
(English / Indonesian)
BEFORE GETTING STARTED
This document is designed to aid you to get started with the device. If you experience problems following
these guides or need further information pertaining to the device, please visit our website at
www.prolink2u.com. All specifications are subject to the manufacturer’s configuration at the time of
shipping and may change without prior notice, written or otherwise.
1. Package Contents
Items:
One (1) PROLiNK
®
PRT7010L with built-in 2000mAh
Lithium (Li-ion) Battery
One (1) unit of USB Cable
One (1) piece of Quick Installation Guide (QIG)
1
2
3
Note:
1. The illustrations in this document may appear different from your model.
2. If any of above item is not packed in your package when open, please consult
your reseller immediately.
EN 1
1
2
3
Quick Installation Guide
Portable 4G LTE
WiFi Hotspot
MODEL NO:
PRT7010L
Version 1.00
(English / Indonesian)
BEFORE GETTING STARTED
This document is designed to aid you to get started with the device. If you experience problems following
these guides or need further information pertaining to the device, please visit our website at
www.prolink2u.com. All specifications are subject to the manufacturer’s configuration at the time of
shipping and may change without prior notice, written or otherwise.
2. Overview
4
Interface and Buttons
1. SIM/USIM Card Slot /
Reset Button
2. WPS Button
EN 2
4
3. Power Button
4. LED Indicator
5. Micro USB Port
Indicators
When the device is powered on, the following icons may be
displayed on the screen. For a description of the icons, refer to the
following table.
Red Solid/ Blinking : The battery is low.
Please charge the battery.
Green Blinking : The battery is being charged or in
standby mode.
Green Solid : The battery level is middle or high.
LED Light Off : Your device is not being charged, or
the battery is not inserted.
5
4
1
2
3
2. Overview
EN 3
Blue Solid : Wi-Fi is active.
Blue Blinking : WPS is active.
LED Light Off : Wi-Fi is off or your device is in sleep mode.
Blue Solid : One or more unread messages.
Blue Blinking : One or more new messages are received.
LED Light Off : No message.
Red Solid : Error status. Not registered to the mobile
network, no (U)SIM card inserted or no
network service available.
Green Solid : Registered to the 2G/3G mobile network.
Green Blinking : Connected to the 2G/3G mobile network and
data is being transferred.
Blue Solid : Registered to the 4G LTE network.
Blue Blinking: : Connected to the 4G LTE network and data is
being transferred.
EN 4
3. Hardware Installation
12
3
Inserting SIM Card
1. Open the SIM (or USIM) card cover.
2. Insert a SIM (or USIM) card to the card slot, you will hear a click
sound when the SIM (or USIM) card is locked in place.
3. Close the SIM (or USIM) card cover.
Note:
1. Open the card slot cover gently.
2. PRT7010L does not support the Micro/Nano SIM card. To avoid damaging the
device, do not use Micro/Nano SIM cards or with any card holders.
EN 5
3. Hardware Installation
Note:
1. If the system does not launch installation automatically, you can run the
installation program in the path of My Computer > PROLiNK 4G.
2. The driver of your device will be installed at the same time.
PRT7010L supports three working modes.
i. USB Mode – Connection via the USB cable.
• Connect your device to the client with the USB cable.
• Power on your device.
• Follow the system prompts to complete the software
installation.
• After the installation, the system will create a shortcut icon on
your desktop. Double click on the shortcut and it will lead you
to the web configuration page of PRT7010L.
Unless you need to change your 3G/4G settings or access the
advanced settings of the device, you can access the Internet without
the need to configure the device.
The WAN connection mode is “Automatic” by default.
EN 6
ii. Wi-Fi mode - Connection via Wi-Fi
Power on your device directly.
It will take 1~2 minutes to initialize.
Use your normal Wi-Fi application on the client to search for the
available wireless network.
Select the SSID of your device (default SSID is
PROLiNK_PRT7010L_xxxxx), and then click Connect. The password is
set as prolink12345 by default.
The WAN connection mode is “Automatic” by default. You can access
the Internet without the need to configure the device.
If you need to change your 3G/4G settings or access the advanced
settings of the device, refer to “Accessing the WebGUI configuration
page”
3. Hardware Installation
EN 7
3. Hardware Installation
4. Web-based Conguration
iii. Mixed Mode – Connection via both USB and Wi-Fi
This is a combination of using the USB cable and Wi-Fi connection.
Input the case-sensitive default password “password”, and then click
Login to access the WebGUI configuration page.
Accessing the WebGUI Configuration Page
Make sure the connection between your device and the client is
active. Launch the Internet browser and enter http://192.168.123.1 or
http://p.home
The login page will appear as follow.
EN 8
Select Settings > Network Settings Change Connection Mode,
Network Selection or APN
Setting.
Select Settings > Wi-Fi Settings Change the basic wireless
network settings, choose
security mode and WPA
type, and perform the WPS
configuration.
Select Settings > Device Settings Change the Administrator
settings, restore factory
default, manage PIN or set the
LAN interface configuration.
Setting
After logging in, you can also select Settings, and do the following
operations.
Quick Setup
After logging in, select Settings > Quick Settings, and then the Quick
Setup wizard will appear.
The Quick Setup wizard will guide you on setting up the basic
parameters for your device in the safest way. After this procedure,
you can use your Internet service.
4. Web-based Conguration
Note:
If you select Manual APN, please consult your ISP on the APN name to be entered.
EN 9
4. Web-based Conguration
Select Settings > Firewall Set the Mac/IP/Port Filtering,
Port Forwarding or the System
Security configuration.
Select Settings > Router Settings Change Router LAN IP and
DHCP settings.
Select Settings > Internet Wi-Fi Connect to Hotspot as Wi-Fi
repeater.
EN 10
Disconnect from the Internet
1. Log in the WebGUI Configuration page, and go to Home.
2. Click Connect / Disconnect to connect or to terminate the Internet
connection.
Sleep Mode
The device will enter into Sleep Mode when no users are connected
to the device in 10 minutes. Press Power or WPS button to wake up
the device.
Note:
With USB connection and no Wi-Fi user connected to the device within 10 minutes,
only the Wi-Fi function will be disabled. Hold the WPS button for about 3 seconds
to enable this function.
Note:
Turning off the device can also terminate the Internet connection.
4. Web-based Conguration
Items:
Satu (1) PROLiNK
®
PRT7010L dengan built-in 2000mAh
Lithium (Li-ion) Baterai
Satu (1) unit of Kabel USB
Satu (1) buah Lembar Panduan Instalasi
1
2
3
Catatan:
1. Ilustrasi didalam dokumen ini mungkin akan berbeda dari model perangkat
yang Anda miliki.
2. Jika terdapat item diatas yang tidak ditemukan pada isi kemasan, silahkan untuk
menhubungi dealer Anda secepatnya.
1
2
3
1. Isi Kemasan
ID 1
Quick Installation Guide
Portable 4G LTE
WiFi Hotspot
MODEL NO:
PRT7010L
Version 1.00
(English / Indonesian)
BEFORE GETTING STARTED
This document is designed to aid you to get started with the device. If you experience problems following
these guides or need further information pertaining to the device, please visit our website at
www.prolink2u.com. All specifications are subject to the manufacturer’s configuration at the time of
shipping and may change without prior notice, written or otherwise.
ID 2
2. Penjelasan
Tombol dan Antarmuka
1. Slot Kartu SIM/USIM /
Tombol Reset
2. Tombol WPS
3. Tombol Power
4. LED Indikator
5. Port Micro USB
Indikator
Bila perangkat diaktifkan, ikon berikut akan ditampilkan pada layar.
Untuk penjelasan dari ikon, mengacu pada tabel berikut.
Merah tidak brkedip / Berkedip : Baterai Lemah.
Hijau Berkedip : Sedang mengisi Baterai atau dalam
modus siaga.
Hijau tidak berkedip : Capasitas isi baterai pada posisi
menengah atau tinggi.
Lampu LED tidak menyala : Perangkat Anda tidak dalam
pengisian, atau tidak ada baterai.
4
4
5
4
1
2
3
Biru tidak berkedip : Wi-Fi berkerja.
Blue berkedip : WPS berkerja.
Lampu LED tidak menyala : Wi-Fi tidak menyala atau prangkat
dalam modus tidur.
Biru tidak berkedip : satu atau lebih pesan belum terbaca.
Biru berkedip : satu atau lebih pesan baru di terima.
Lampu LED tidak menyala : tidak ada pesan.
Merah tidak berkedip : Status Error. Tidak terhubung ke ISP,
tidak ada kartu (U)SIM atau jaringan
network ISP tidak terdeteksi.
Hijau tidak berkedip : Registered pada jaringan 2G/3G.
Hijau berkedip : Terhubung ke jaringan 2G/3G dan ada
transfer data.
Biru tidak brkedip : Registered pada jaringan 4G LTE.
Biru berkedip : Terhubung ke jaringan 4G LTE network
dan ada transfer data being transferred.
ID 3
2. Gambaran
3. Instalasi Perangkat
Memasukkan Kartu SIM
1. Buka penutup SIM (atau USIM).
2. Masukkan SIM (atau USIM) ke dalam slot SIM, akan terdengar
bunyi klik jika SIM (atau USIM) sudah benar-benar terpasang.
3. Tutup penutup SIM (or USIM).
Catatan:
1. Buka penutup SIM secara perlahan.
2. Untuk menghindari kerusakan perangkat, dilarang menggunakan kartu Micro /
Nano SIM (sekalipun menggunakan Adapter kartu)
12
3
ID 4
3. Instalasi Perangkat
Catatan:
1. Jika sistem tidak memulai instalasi secara otomatis, Anda dapat menjalankan
program melalui My Computer> PROLiNK 4G.
2. Drivers perangkat Anda akan terinstal di waktu yang bersamaan.
PRT7010L mendukung tiga modus kerja.
i. Modus USB – Koneksi melalui kabel USB
• Koneksikan perangkat Anda ke klien dengan kabel USB.
• Hidupkan perangkat Anda.
• Ikuti sistem untuk menyelesaikan instalasi perangkat lunak.
• Setelah instalasi selesai, sistem akan membuat ikon shortcut
pada desktop Anda. Klik dua kali pada shortcut
tersebut untuk menuju pada halaman Web konfigurasi
PRT7010L.
Jika Anda tidak memerlukan pengaturan 3G/4G atau mengakses
pengaturan lanjutan lainnya dari perangkat, Anda dapat mengakses
Internet tanpa perlu mengkonfigurasi perangkat terlebih dahulu.
Modus koneksi WAN adalah "otomatis" secara default.
ID 5
ii. Modus WiFi – Koneksi melalui WiFi
Hidupkan perangkat Anda secara langsung.
Ini akan memakan waktu 1 ~ 2 menit untuk menginisialisasi.
Gunakan aplikasi WiFi yang biasa anda gunakan pada computer
atau yang lainnya, untuk mencari jaringan nirkabel dari perangkat.
Pilihlah SSID dari perangkat PRT7010L (Default SSID adalah
PROLiNK_PRT7010L_xxxxx), lalu klik konek.
Default password adalah prolink12345.
Secara default Modus koneksi WAN adalah "otomatis". Anda dapat
mengakses Internet tanpa perlu mengkonfigurasi perangkat.
Jika Anda perlu mengubah pengaturan 3G/4G atau mengakses
pengaturan lanjutan dari perangkat, lihat "Mengakses
halaman konfigurasi WebGUI"
3. Instalasi Perangkat
ID 6
4. Kongurasi Web Base
iii. Modus Campuran – Koneksi melalui WiFi dan USB
Ini adalah kombinasi dengan menggunakan kabel USB dan Wi-Fi.
Masukkan default kata sandi dengan "password", lalu klik Login
untuk mengakses halaman konfigurasi WebGUI.
ID 7
Mengakses Halaman Konfigurasi WebGUI
Pastikan anda terhubung dengan perangkat PRT7010L. buka
peramban internet dan masukan http://192.168.123.1 atau
http://p.home
Halaman login akan muncul seperti berikut.
3. Instalasi Perangkat
ID 8
Pilih Settings > Network Settings Mengubah Model Koneksi,
pilih Network atau ubah
pengaturan APN.
Pilih Settings > Wi-Fi Settings Mengubah pengaturan
jaringan nirkabel dasar, pilih
Model keamanan dengan
model WPA, dan melakukan
konfigurasi WPS.
Pengaturan
Setelah login masuk, Anda juga dapat memilih pengaturan hal berikut.
Pengaturan Cepat
Setelah login, pilih Settings > Quick Settings, dan kemudian wizard
Pengaturan Cepat akan muncul.
Wizard Pengaturan Cepat akan memandu Anda dengan pengaturan
parameter dasar perangkat dengan cara yang paling aman. Setelah
prosedur ini, Anda dapat langsung menggunakan layanan Internet
Anda.
4. Kongurasi Web Base
Catatan:
Jika Anda memilih APN Manual, silakan berkonsultasi dengan ISP Anda untuk
nama APN yang harus di masukan.
/