Garden Oasis SC-176NSF/4 Owner's manual

Brand: Garden Oasis

Model: SC-176NSF/4

Type: Owner's manual

OWNER’S

MANUAL

Date of purchase: _____/ _____/ _____

Malden 4 Piece

Seating Set

Product code: D71 M80446

UPC code: 7-6945575825-5

Vendor Item: SC-176NSF/4

PARTS

Read through all the instructions before beginning assembly. Unpack and identify all the parts.

Place them on a flat, non-abrasive surface. Assembly by two people is recommended.

ACCESSORIES

A1 (3)

Right Arm

A2 (3)

Left Arm

B (2)

Seat for Cushion Chair

C (2)

Back for Cushion Chair

D (1)

Seat for Loveseat

E (1)

Back for Loveseat

F (4)

Back Cushion

G (4)

Seat Cushion

H (1)

Table Top

I (4)

Metal Leg

J (1)

Metal Center Ring

Ka (6 + 1 spare)

M6 x 25L Bolt

Kc (4)

M6 x 36L Bolt

Kd (12 + 1 spare)

M6 x 50L Bolt

Ke (6+1 spare)

M6 x 60L Bolt

Kf (4)

Screw

Kb (2 )

M6 x 30L Bolt

Kg (36 + 2 spares)

Kh (12 + 1 spare)

Nut

Ki (1)

Hex Wrench

Kj (1)

Allen Wrench

Kk (1)

Assembly Instructions

Sheet

Metal Washer

Kl (1 spare)

Glass Bumper

ASSEMBLY INSTRUCTIONS

Attach the back for cushion chair (C) to the seat

for cushion chair (B). Align the holes, insert an

M6 x 25L bolt (Ka) through a metal washer (Kg), the

back for cushion chair (C) and secure into the seat for

cushion chair (B). See Fig. 1. Repeat procedure for

the other side. Do not tighten completely.

Attach the left arm (A2) to the seat (B). Align the

holes, for upper hole insert an M6 x 50L bolt (Kd)

through a metal washer (Kg), the arm (A2) and

secure into the front crossbar of the seat (B). For

lower hole insert an M6 x 50L bolt (Kd) through a

metal washer (Kg), the arm (A2), the bracket of the

seat (B) and secure with a nut (Kh). See Fig. 2. Do

not tighten completely. Then insert an M6 x 60L

bolt (Ke) through a metal washer (Kg), the arm (A2),

the back (C), another metal washer (Kg) and secure

with a nut (Kh). See Fig. 3. Do not tighten completely.

Repeat procedure for the right arm (A1). Securely

tighten all bolts. (Note: the arm label with “left” or “right”).

All parts are shrink wrapped together. Remove all

components from the box and place on top of the

box. Carefully cut the wrapping open. Count and

identify all parts.

Attach the seat for loveseat (D) to the back for

loveseat (E). Align the holes, for each hole on the side

insert an M6 x 25L bolt (Ka) through a metal washer (Kg),

the back for loveseat (E) and secure into the rear crossbar

of the seat (D). See Fig. 5. Do not tighten completely.

For each hole in the medium insert an M6 x 30L bolt (Kb)

through a metal washer (Kg), the rear crossbar of the

seat (D) and secure into the back (E). See Fig. 6. Do

not tighten completely.

Place the back cushion (F) and seat cushion (G)

onto the assembled chair frame and fasten to the

frame. See Fig. 4. Repeat procedure for the other

cushion chair.

Fig. 1

Fig. 3

Fig. 2

Fig. 4

Fig. 5

Fig. 6

Made in CHINA

Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179

See our extensive assortment of outdoor living products

on-line at www.sears.com and www.kmart.com

For questions or comments about product:

Call toll-free:

800-457-4652

Please refer to part numbers when reordering

CARE INSTRUCTIONS

Wash with a mild solution of soap and water; rinse thoroughly. Dry completely. Do not use bleach or solvents.

Cover furniture with outdoor furniture covers when not in use.

Attach the left arm (A2) to the seat for the loveseat (D).

Align the holes, for upper hole insert an M6 x 50L bolt (Kd)

through a metal washer (Kg), the arm (A2) and secure

into the front crossbar of the seat (D). For lower hole

insert an M6 x 50L bolt (Kd) through a metal washer (Kg),

the arm (A2), the bracket of the seat (D) and secure with

a nut (Kh). See Fig. 7. Do not tighten completely. Then

insert an M6 x60L bolt (Ke) through a metal washer (Kg),

the arm (A2), the back for the loveseat (E), another metal

washer (Kg) and secure with a nut (Kh). See Fig. 8. Do

not tighten completely. Repeat procedure for the right

arm (A1). Securely tighten all bolts.

Place the back cushions (F) and seat cushions (G) onto the

assembled loveseat frame and fasten to the frame. See Fig. 9.

Place the tabletop (H) on a flat surface. Insert four metal

legs (I) into the plastic receivers on the table rim (H).

Adjust the plastic receiver positions on the rim by

sliding back and forth as necessary. Place a metal center

ring (J) between legs, Align the holes and insert an

M6 x 36L bolt (Kc) through a metal washer (Kg), through

a metal center ring (J) and secure into the leg (I) for each

hole. Do not tighten completely. See Fig. 10.

Insert a screw (Kf) through each plastic receiver on the rim

and into the tip of each leg. See Fig. 11. Turn the table over.

Securely tighten all bolts and screws by using the

-wrenches (Ki, Kj).

Your 4 pc seating set is ready for use now!

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11

Garden Oasis SC-176NSF/4 Owner's manual

Garden Oasis SC-176NSF/4 Owner's manual

Garden Oasis SC-176NSF/4 Owner's manual

Related papers

Other documents