Haier HWM110-9188 User manual

Order NO. TL1101S001V1

Model Number HWM110-9188

C

2011 Haier Washing Machine

Order No.TL1101S001V1

-2-

Chapter 1 : General Information

Chapter 2.Product Feature .............................................................. 4

Chapter 3. Safety Precautions .......................................................... 6

Chapter 4. Installation and accessory parts ............................................. 8

Chapter 5. Parts and functions .........................................................13

Chapter 7. Maintenance service and trouble shooting .................................... 16

Chapter 8. Wiring diagram...............................................................20

Chapter 6. Operating Instruction ....................................................... 14

1-1. Table of Contents

Chapter 1. General Information ....................................................................................2

1-1. Table of Contents 2

1-2. General Guidelines 3

1-3. Caution and Warning symbols 3

1-4. Function indication symbols 3

2-1. Features 4

2-2. Specification 5

3-3.Net dimension 8

3-1. Safety 6

3-2. Warning and cautions 7

4-1. Key points in installation 8

7-1.Trouble-shooting charts

7- - . 61 1 No action(The indicator is off) 1

7- - 71 2.No draining 1

7- - 71 3.Keep filling water 1

7- - 81 4.No spinning 1

7- -1 5.Too much noise in spinning

7- - 81 6.Too much noise in washing 1

7-2. Trouble alarm and solve method 19

7-3.Common phenomena

16

18

19

4-2. Install the bottom plate 8

4 3.Adjust the installation position 9-

4 . -4 How to change the direction of the drain hose 9

4 . the drain hoses 10-5 Usage

4 . the water faucet 10-6 Confirm

4 . -7 Connection between the water inlet hose jointer and the water faucet 11

4 . -8 Connection between the water inlet hose and the water 11

4 . -9 Connection between the jointer of the water inlet hose and the water inlet hose 12

4 .-10 Check the connection between the water inlet hose jointer and the water faucet

4 . -11 Dismantle the water inlet hose 12

12

Model No.: HWM110-9188/HWM110-9188DD

Issue

Rev.

1-2. General Guidelines

1-3. Caution and Warning symbols

When servicing, observe the original lead dress. If a short circuit is found, replace all parts

which have been overheated or damaged by the short circuit. After servicing, see to it

that all the protective devices such as insulation barriers, insulation papers shields are

properly installed. Confirm that the screws parts and wiring which were removed in

(You will see them in “Matters needing attention”)

order to service are put in the original positions, or whether there are the portions which

are deteriorated around the service places serviced or not. And be sure safety of that

Any instructions in this service manual with this “Warning” sign must be

followed strictly.

To prevent damage to the washing machine, any instructions in this service

manual with this “Stop” sign must be followed strictly.

1-4.Function indication symbols

(You will see them in the specification table)

Signify the washing machine has this function.

Signify the washing machine doesn′t have this function.

-3-

Order No.TL1101S001V1

● Shift washing, shift spinning

●

Cold & warm water inlet selection

Drain up function

Cabinet with the door open in the front:

Super capacity for more clothes

Pulsator type for wash efficiency, twist free and low wear

-4-

Chapter 2.Product Feature

2-1. Features

Order No.TL1101S001V1

-5-

2-2. Specification

M o del H W M 1 1 0 -9 1 8 8

Fre e standing √

Built under ×

EAN code

Energy efficiency cla ss

Features for use

W ash capacity kg 11

Spin capacity kg 11

Level/V olum e L 1/21， 2/3 2， 6/42， 4 /51， 5/60， 6/69， 7/77， 8/94

Pre set H √

Residual da m pness % <115

C on t r al m od el

contraller ×

Norm al com p uterize d ×

Fuzzy com puterized √

Fre quency conversion ×

Service features

Pro gram s 8

Short cycle ?

Inlet heating select √

Heating selec tion ×

Spinning cycle (selector) ×

Spinning cycle (varia ble) ×

Start/Pause √

Autom atic balncing ?

Aes thetics

Cabinet m aterial（ P= Plastic/Z =Zinc king/C= Cold ) Z

Rolled stainless steel

Inner drum (stainl. steel=s / plastic=p) S

D rain type（ U =d rain up D =d rain down ） drain down

Door (glass= g / plastic=p) ×

Adjustable feet √

Tech nical d ata

Voltage/frequency V/Hz 220V -240V /50 H Z

W ash power W 550

Spin power W 360

Special function －

Air-Bubble ×

Feet w heel ×

W ater fall current ×

Dim en sions (m easu rem ents)

Height / built under m m 1055

W idth m m 660

Depth / with open door m m 660

Dim en sions packed ( m easu rem ents packed)

Height m m 1140

W idth m m 727

Depth m m 727

Net w eight kg 57

G ross w eight kg 70

20'C ontainer lo ad Sets 42

40’C ontain er lo ad Sets 90

40H’C ontainer load Sets 90

NOTE: "√ " FOR AVALIABLE, " ×" FOR NOT AVALIABLE “ -” FOR N OT AVAILABLE

Product Specification

" -" FO R B E A P P L IC A B L E

Order No.TL1101S001V1

Do not share one receptacle with other

electric appliances. Do not use it in

case that the power plug is damaged

or the inserting into the receptacle is

loose.

Earth

Do not wash water-proof laundries such

as the raincoat, bicycle shelter etc. To

avoid abnormal vibration during spinning.

If the power cord is bad, to avoid risk it is required to replace it by the technicians

of our special shop or the after-sale service department. Keep the pin of the power

plug clean.

Be sure to earth the earthing wire reliably.

Do not put the machine at damp place like

the bathroom. Never wash it with water.

Do not let the machine share one receptacle

with other electric appliances. If the power

plug is damaged, or the plugging into the

receptacle is loose, do not use the plug any

more.

Do not install or store the washer where

it will be exposed to the weather.

The power cord plug should be convenient

to be pluged in or pluged out with hand while

the washing machine runs normally. Be sure to

pull the plug out and close the water tap when

the machine is idle, when moving the machine,

or when cleaning the machine.Do not use wet

hand to insert or pull out the power plug.

-6-

Chapter 3. Safety Precautions

3-1. Safety

Order No.TL1101S001V1

-7-

3-2. Warning and cautions

Order No.TL1101S001V1

Unit（mm）

4-2. Install the bottom plate

Please install and adjust the machine according to the requirement of the manual.

It is very important to your security and correct operating the machine.

-8-

4-1. Key points in installation

3-3.Net dimension

Chapter 4. Installation and accessory parts

Order No.TL1101S001V1

4 .-4 How to change the direction of the drain hose

4 3.Adjust the installation position-

-9-

°

Page 4

Order No.TL1101S001V1

-10-

4 . the drain hoses-5 Usage

4 . the water faucet-6 Confirm

Order No.TL1101S001V1

-11-

4 .-7 Connection between the water inlet hose jointer and the water faucet

4 .-8 Connection between the water inlet hose and the water

Order No.TL1101S001V1

-12-

4 .-9 Connection between the jointer of the water inlet hose and the

water inlet hose

4 .-10 Check the connection between the water inlet hose jointer and

the water faucet

4 .-11 Dismantle the water inlet hose

Order No.TL0910001V0

-13-

Chapter 5. Parts and functions

Order No.TL1101S001V1

-14-

Chapter 6. Operating Instruction

Order No.TL1101S001V1

-15-

Order No.TL1101S001V1

-16-

If you replace the computer sequencer without checking the other components carefully,

the computer sequencer may be damaged again. Therefore, please first check

if the other components working normally before replacing the sequencer in maintenance.

C

7-1.Trouble-shooting charts

7 1 1 No action(The indicator is off)- - .

Confirm that there's no power failure,

and the power plug is inserted reliably.

The power switch is at "On" mode.

Measure the voltage

of the two ends of the power input

of the sequencer.

Measure the resistance

between the white wire terminal

in the white plug on top of the wire unit

and the N pin on the power

receptacle.

Replace the sequencer.

Replace the

power cord.

Replace the wire unit.

Replace the computer

sequencer.

Connect the fuse and the

wires of the two ends.

The resistance

is 0.

The resistance

is 0.

The resistance

is 0.

Infinite

Yes

Infinite

No

Pull off

the power

plug

Not exist

Exist

Check if the connection

between the fuse and the wires

of the two ends are well?

Measure the resistance

between the brown wire terminal

in the white plug on top of the wire

unit and the brown wire of

the lower part.

Measure the resistance

between the light blue wire terminal

in the red plug on top of the wire unit

and the light blue wire of

the lower part.

Chapter 7. Maintenance service and trouble shooting

Order No.TL1101S001V1

7- -1 2.No draining

No

After insert the plug, turn the

sequencer knob to the drain location

Check the inset is normal

and measure the voltage of two ends of

the drain pump

Check the inset is normal

and measure the voltage of two ends of

the drain motor

Replace the drain pump

Check if the drain pump acts.

Check if the drain motor is normal

Check if the wire unit is normal

No

Yes

No

Check if the wire unit is normal?

Replace the sequencer

Repair or replace the wire unit

Yes

7- -1 3.Keep filling water

Open the water faucet without switching on the power.

If the water can fill into the water inlet valve.

check if the gas guide system such

as gas cell leaks gas

Replace the water inlet valve.

Replace the water level sensor.

It leaks gas. Please check and repair the gas guide system.

Please smear 801 glue in installation of the connecting pipe.

Please smear 801 glue in installation of the gas cell cover.

No

Exist

-17-

Order No.TL1101S001V1

The washing and

draining are normal.

Check the On/Off point of the

microswitch and stop switch.

Check if the clutch pawl

is pulled enough.

Replace the microswitch

or stop switch.

Replace the drain motor.

Replace the retarder clutch.

At this time please check

if the drain motor is well.

No On/Off point

No

Yes

Normally

7-1-5.Too much noise in spinning

No

Yes

No

If the washing machine is set horizontally.

If the noise of the gear case is large.

If the hanger is wrongly used.

If the noise of the motor is too much.

If the motor is fastened tightly.

Set the machine horizontally.

Replace the retarder

Replace the hanger.

Replace the motor.

Fasten the motor.

No

Yes

7- -1 6.Too much noise in washing

If the noise of the motor is too much.

If the pulsator is rubbing the

bottom of the inner tub.

If the motor fastened tightly.

If the noise of the retarder is too large.

If the belt is too tight or loose.

Fasten the motor.

Replace the retarder.

Adjust the belt.

Replace the motor.

Adjust the gap between the

pulsator and inner tub

7-1-4.No spinning

-18-

Order No.TL1101S001V1

-19-

7-2. Trouble alarm and solve method

Order No.TL1101S001V1

There is overload protector installed in the motor. In case that the motor is overload or meets

breakdown in working, the protector will act and stop the motor. When the breakdown is

removed, the motor will resume normal working.

-20-

Chapter 8. Wiring diagram

Life Line

Brown

Blue

Program Control Unit

Wiring Diagram

Green/Yellow

Fuse

Brown

Door Switch

Water Level

Sensor

Balance

Switch

Red/White

Retractor

Yellow

Orange

Motor

Water Inlet Valve

White

Red

Grey

Green/White

Blue

Softener Valve

Program Display Unit

Life Line

Page is loading ...

Haier HWM110-9188 User manual

Haier HWM110-9188 User manual

Related papers

Other documents