Agri-Fab 45-0545 User manual

Category
Spreader
Type
User manual

Agri-Fab 45-0545 is a 175 LB Tow Spiker Spreader, a versatile tool designed to enhance lawn care and maintenance tasks. Its robust construction and efficient design make it suitable for various applications.

With its 175-pound towing capacity, the spreader can effortlessly handle large quantities of lawn chemicals, ensuring even and precise distribution. The spiker disks effectively penetrate the soil, creating channels for the chemicals to reach the roots of the grass, promoting healthy growth and preventing weeds.

The adjustable flow control mechanism allows for customization of the spreading rate, adapting to different lawn sizes and chemical requirements. The hopper's generous capacity enables extended use without frequent refilling, maximizing efficiency and minimizing interruptions.

Agri-Fab 45-0545 is a 175 LB Tow Spiker Spreader, a versatile tool designed to enhance lawn care and maintenance tasks. Its robust construction and efficient design make it suitable for various applications.

With its 175-pound towing capacity, the spreader can effortlessly handle large quantities of lawn chemicals, ensuring even and precise distribution. The spiker disks effectively penetrate the soil, creating channels for the chemicals to reach the roots of the grass, promoting healthy growth and preventing weeds.

The adjustable flow control mechanism allows for customization of the spreading rate, adapting to different lawn sizes and chemical requirements. The hopper's generous capacity enables extended use without frequent refilling, maximizing efficiency and minimizing interruptions.

PRINTED IN U.S.A. FORM NO. 45601 (01/17/19)
45-0545
175 LB. TOW
SPIKER SPREADER
youtube.com/c/agrifab
Video
Instruction
Guide
Want more information or assembly tips?
2
RULES FOR SAFE OPERATIONS
• Readthisowner'smanualbeforeattemptingto
assembleoroperatethespiker/spreader.
• Readthetowingvehicleowner'smanualandknow
howtooperatethetractorbeforeusingthespiker/
spreader.
• Donotallowanyonetorideonorsitonthespiker/
spreader.
• Neverallowchildrentooperatethetractororspiker/
spreader.
• Donotallowadultstooperatethetractororspiker/
spreaderwithoutproperinstructions.
• Readthechemicallabelforinstructionsandcautions
forhandlingandapplyingchemicals.
Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment.
Exercisecautionatalltimes,whenusingpowerequipment.
• Weareyeandhandprotectionwhenhandlingand
usinglawnchemicals.
• Alwaysbeginwiththetransmissioninrst(low)gear
andgraduallyincreasespeedasconditionspermit.
Maximumtowingspeed-6M.P.H.
• Donotdrivetooclosetoacreekorditchandbealert
forholesandotherhazardswhichcouldcauseyouto
losecontrolofthetractorandspiker/spreader.
• Beforeoperatingthevehicleonanygrade(hill)refer
tothesafetyrulesinthevehicleowner'smanual
concerningsafeoperationonslopes.Stay off steep
slopes!
• Followmaintenanceandlubricationinstructionsas
outlinedinthismanual.
Lookforthissymboltopointoutimportantsafetyprecautions.Itmeans—Attention!!
Become alert!! Yoursafetyisinvolved.
3
1
2
4
8
9
7
6
5
10
3
47712
24531
23014
63850
24542
24647
24660
24532
47679
24648
69416
69441
41863
11
13
28606
14
15
16
12
63949
CARTON CONTENTS
1. HopperAssembly
2. ChainCover
3. TransportHandle
4. HopperBrace
5. FlowControlGauge
6. FlowControlArm
7. FlowControlRod
8. TongueBraces(2)
9. Tongue
10.HitchBracket
11. LiftTubeAssembly
12.Axle
13.DriveDisk(2)
14.SpikeDisk(10)
15.CenterBrace(2)
16.Wheels(2)
4
REF. PART NO. QTY. DESCRIPTION
A 45100 2 HexBolt,1/2"x4"
B 43001 1 HexBolt,3/8"x1"
C 1509-90 1 HexBolt,1/4"x1-1/4"
D 1509-69 2 HexBolt,1/4"x1-3/4"
E 43012 2 HexBolt,1/4"x3/4"
F 43866 16 HexBolt,1/4"x5/8"
G 44950 1 CarriageBolt,1/4"x3/4"
H 44326 2 CarriageBolt,5/16"x1"
I 48106 2 ShoulderBolt
J 47189 24 NylockNut,1/4"
K 47810 2 NylockNut,5/16"
L H A 2 1 3 6 2  1 NylockNut,3/8"
M 43082 2 HexLockNut,3/8"
N 43019 2 HexJamNut,1/2"
O R19212016 12 Washer,5/8"
P R19171616 4 Washer,1/2"
Q 43088 10 FlatWasher,1/4"
REF. PART NO. QTY. DESCRIPTION
R 1 5 4 3 - 6 9  3 NylonWasher
S 48115 2 NylockHexJamNut,1/2"
T 47684 1 ChainwithConnector
U 47623 1 HitchPin
V 43093 3 CotterPin,1/8"x1-1/2"
W 43343 1 HairCotterPin
X 43849 1 PlasticKnob
Y 47707 1 TransportHandleGrip
Z 43848 1 ControlArmGrip
AA 74 1- 0 2 4 9  16 FlangedBearing
BB 47777 2 Spring
CC 47711 2 Ferrule
DD 46838 1 Spacer,.5"
EE 47683 6 Spacer,2.9"
FF 47782 1 Spacer,3.2"
HA24629 2 30"PlasticTie(notshown)
B
(1)
C
(1)
D
(2)
E
(2)
F
(16)
G
(1)
H
(2)
Q
(10)
S
(2)
T
(1)
R
(3)
J
(24)
K
(2)
P
(4)
SHOWN FULL SIZE
NOT SHOWN FULL SIZE
X
(1)
Y
(1)
BB
(2)
V
(3)
W
(1)
A
(2)
N
(2)
M
(2)
I
(2)
U
(1)
Z
(1)
DD
(1)
CC
(2)
EE
(6)
FF
(1)
AA
(16)
O
(12)
L
(1)
45100
43001
43012
43866
44950
44326
48106
47189
47810
43082
43019
48115
43088
47684
47623
43093
43343
43849
43848
47782
47683
46838
47711
47777
741-0249
47707
R19171616
R19212016
1543-69
HA21362
1509-69
1509-90
5
TOOLS REQUIRED FOR ASSEMBLY
(2)7/16"Wrenches
(2)1/2"Wrenches
(2)9/16"Wrenches
(2)3/4"orAdjustableWrenches
(1)Pliers
(1)KnifeorScissors
ASSEMBLY
Spikepointsaresharp.Wearprotectivegloves
andexercisecautionwhenworkingwithhands
nearspikedisks.
FIGURE 1
FIGURE 3
FIGURE 4
FIGURE 2
1. Removethehardwarepackandallindividualpartsfrom
thecartonandlayoutasshownonpages2and3.
2. Pressaangedbearing(AA)intoeachspikedisk(14)
fromtheatsideofthedisk.Seegure1.
3. Pressaangedbearing(AA)intoeachendofboth
drivedisks(13).Seegure2.
5. Assemblea1/2"spacer(DD)anda5/8"washer(O)
ontotheaxle(12).Seegure4.
4. Pressaangedbearing(AA)intobothcenterbraces
(15)fromtheatsideofeachbrace.Seegure3.
AA
14
AA
AA
13
AA
15
O
DD
12
6
FIGURE 6
FIGURE 7
8. Assembletwospikedisks(14)anda2.9"spacer(EE)
ontotheaxle.Theatsideofthedisksshouldface
awayfromthespacer.Seegure7.
9. Assembletwo5/8"washers(O)andaspring(BB)
ontotheaxle.Seegure7.
IMPORTANT:Whenassemblingpartsontotheaxle,be
surethatthespikedisksarefacinginthedirectionshown
ineachassemblydrawing.
7. Assemblethree5/8"washers(O)andthetwodrive
disks(13)ontotheaxle.Seegure6.
FIGURE 5
6. Assembletheaxle(12)throughtheendofthespread-
erframethatcontainsapre-assembledsprocket.See
gure5.
10.Assembletwospikedisks(14)anda2.9"spacer(EE)
ontotheaxle.Theatsideofthedisksshouldface
awayfromthespacer.Seegure8.
FIGURE 8
12
O
O
13
14
14
EE
O
O
BB
14
14
EE
7
12.Assembletwospikedisks(14)anda2.9"spacer(EE)
ontotheaxle.Theatsideofthedisksshouldface
awayfromthespacer.Seegure10.
13.Assembletwo5/8"washers(O)andaspring(BB)
ontotheaxle.Seegure10.
FIGURE 10
11. Assembletwo5/8"washers(O),thetwocenterbraces
(15)andthe3.2"spacer(FF)ontotheaxle.Theat
sideofthebracesshouldfaceawayfromthespacer.
Seegure9.
FIGURE 9
FIGURE 11
14.Assembletwospikedisks(14)anda2.9"spacer(EE)
ontotheaxle.Theatsideofthedisksshouldface
awayfromthespacer.Seegure11.
30" PLASTIC TIES
15.Assemble30"plastictiesaroundtheeachsetof
spikedisksthatsurroundthesprings.Looptheties
aroundoppositesidesofeachspikedisk.Tightenthe
ties,compressingthespringssothatthereisroomto
assembletherestofthepartsontotheaxle,andto
inserttheaxlethroughtheendofthespreaderframe.
Seegure12.
FIGURE 12
O
O
15
15
FF
14
EE
O
O
BB
EE
14
14
8
16.Assemblea2.9"spacer(EE)ontotheaxle.Seegure
13.
17. Assembletwospikedisks(14),a2.9"spacer(EE)
anda5/8"washer(O)ontotheaxle.Theatside
ofthedisksshouldfaceawayfromthespacer.See
gure13.
FIGURE 13
23.Removeconnectinglinkfromchainandassemblethe
chain(T)aroundthesprockets,andthenfastenthe
endsofthechaintogetherusingtheconnectinglink.
Seegure16.
FIGURE 16
FIGURE 14
18.Slidetheaxleonthroughtheendofthespreader
frame.Youmayneedtostraightenthespikedisksthat
arestrappedtogethertoallowtheaxletoslidefreely.
Seegure14.
19.Assemblea5/8"washer(O)ontotheendoftheaxle.
Seegure14.
20.Assembleacotterpin(V)intotheendoftheaxleand
thenspreadtheendsofthecotterpin.Seegure14.
HINT:Youmayneedtopushagainsttheendplateto
makeroomontheaxletoinstallthecotterpin.Tryturning
thespreaderonendtogetbetterleverageforpushing.
FIGURE 17
24.Temporarilyinstalltwo5/16"x1"carriagebolts(H)
and5/16"nylocknuts(K)inthedirectionshowninthe
lifttubeassembly(11).Do not tighten.Seegure17.
21.Assembletwocotterpins(V)intothedrivedisks(13).
Spreadtheendsofthecotterpins.Seegure15.
22.Cuttheplastictiesandremovethemfromthedisks.
Seegure15.
FIGURE 15
CAUTION: Springtension isreleasedwhen
plastictiesarecut.Keephandsclearofspike
diskstopreventinjury.
14
14
O
EE
EE
V
O
V
PLASTIC TIES
T
CONNECTING LINK
H
K
11
9
FIGURE 20
27. Attachthetonguetotheframeassemblytubeusinga
1/4"x1-3/4"hexbolt(D),two1/4"atwashers(Q)and
a1/4"nylocknut(J).Repeatfortheotherside.Do not
tighten yet. Seegure20.
28.Attachthetonguetothecenterbrace(15)usingtwo
1/4"x5/8"hexbolts(F)and1/4"nylocknuts(J).
Repeatfortheotherbrace.Do not tighten yet. See
gure20.
29.Assembletheplasticgrip(Z)ontotheendoftheow
controlarm(6). Seegure21.
30.Inserttheowcontrolarm(6)throughtheslotinthe
hopperbrace(4).Placeanylonwasher(R)oneach
sideofthearmandattachittothebrace'swelded
bracketusinga1/4"x1-1/4"hexbolt(C),a1/4"at
washer(Q),andtwo1/4"nylocknuts(J).Tighten
therstnylocknutuntilthereisnoticeableresistance
whenmovingtheowcontrolarm,thentightenthe
secondnylocknut. Seegure21.
31.Placetheowcontrolrod(7)throughtheholeatthe
endoftheowcontrolarm(6).Assemblethetwo
ferrules(CC)ontothethreadedendsoftherodso
thatapproximately10threads(1/2")oftherodextends
throughtheferrules.Seegure21.
FIGURE 21
26 Assembletheendofthetongue(9)tothehopperusing
two1/4"x5/8"hexbolts(F)and1/4"nylocknuts(J).
Theholesarelocatedjustbelowtheframeassembly
tube.Do not tighten yet. Seegure19.
FIGURE 19
FIGURE 18
25.Attachthelifttubeassembly(11)tothespreaderusing
thetwoshoulderbolts(I)andtwo3/8"hexlocknuts
(M).Seegure18.
I
M
11
J
F
9
FRAME ASSEMBLY TUBE
J
J
F
Q
D
15
R
J
Q
C
Z
CC
7
6
4
1/2"
10
FIGURE 25
39.Assembletheowcontrolgauge(5)tothehopper
braceusingthe1/4"x3/4"carriagebolt(G),anylon
washer(R)andtheplasticknob(X).Seegure25.
34.Insertatonguebrace(8)throughtheslotintheend
plate.Fastenthefrontholeofthetonguebracetothe
endplateusinga1/4"x5/8"hexbolt(F)and1/4"
nylocknut(J).Fortherearholeusea1/4"x3/4"hex
bolt(E),1/4"atwasher(Q),and1/4"nylocknut(J),
withtheboltandwasherassembledfrominsidethe
hopper.Do not tighten yet. Seegure23.
35.Fastentheotherendofthetonguebrace(8)tothe
sideofthetongueusingtwo1/4"x5/8"hexbolts(F)
and1/4"nylocknuts(J).Do not tighten yet.See
gure23.
36.Repeatsteps10and11forthesecondtonguebrace.
3 7. Tightenallboltsandnutsassembledsofar.
FIGURE 23
FIGURE 22
32.Attachthehopperbrace(4)tothehopperusingtwo
1/4"x5/8"hexbolts(F),one1/4"atwasher(Q),
andtwo1/4"nylocknuts(J).Do not tighten yet.See
gure22.
33.Placetheendofthehitchbracket(10)withtwoholes
downthroughtheslotinthetongue.Attachthehopper
bracetothetopofthetongueandthehitchbracketto
thebottomusingone3/8"x1"hexbolt(B)andone
3/8"nylocknut(L).Do not tighten yet.Seegure22.
38.Assemblea1/2"x4"hexbolt(A),a1/2"washer(P),
awheel,a1/2"washer(P),anda1/2"jamnut(N).
Finger tighten only. Attachthewheelassemblyto
thetransporttubeusinga1/2"nylockhexjamnut(S).
Repeatfortheotherside.Seegure24.
FIGURE 24
A
P
P
N
S
L
F
B
Q
J
4
10
F
J
F
J
8
E
Q
J
X
R
G
5
11
43.Attachthetransporthandle(3)totheliftassemblyarm
usingthetwopre-assembled5/16"x1"carriagebolts
and5/16"nylocknuts(K).Seegure27.
44.Assemblethehandlegrip(Y)tothetransporthandle
(3).Seegure27.
FIGURE 28
FIGURE 27
45.Assemblethechaincover(2)totheframeassembly
usingtwo1/4"x5/8"hexbolts(F),1/4"atwashers
(Q)and1/4"nylocknuts(J)asshowngure28.
Pleasenotethatsomepartsarenotshownforclarity.
46.Installthehitchpin(U)andthe1/8"haircotterpin(W)
inthespreaderhitchbracketandtongue.
Seegure28.
41.Tocheckforcorrectopeningofhopperowplates:
a. Settheowcontrolgaugeatthehighestsetting.
b. Movetheowcontrolarmawayfromthehopper
untilitrestsagainstthegauge.Theslotsinthe
bottomofthehoppershouldnowbecompletely
open.Theedgeoftheowplatesshouldbejust
clearoftheendsalltheslots.
c. Iftheowplatesarenotstraightwiththeslots,
screwoneferruleupordownononesideofthe
controlrod.
d. Iftheowplatesopentofarornotfarenough,
screwbothferrulesequallyupordownonthe
controlrod.
d. Movetheowcontrolarmtowardthehopperto
theoffposition.Verifythattheslotsinthebottom
ofthehopperarecompletelycoveredbytheow
plates.
e. Tightenthelocknutsandthenloosen1/4turn.
42.Tocheckforpropertensiononthehopperowplates:
a. Settheowcontrolgaugeatamidrangesetting.
b. Movetheowcontrolarmagainstthegauge.
c. Pressrmlyagainstthefrontoftheowplates
atthebottomofthehopper.Theowcontrolarm
shouldnotmove.
d. Ifthearmmoves,tightenthehexlocknutsonthe
owcontrolarmuntilmovementisprevented.
40.Checkthatbothferrules(CC)areadjustedsothat
approximatelytenthreads(1/2")ofthecontrolrodis
exposed.Insertbothferrulesintothebracketswhich
arerivetedtothefrontoftheowplates.Assemble
a1/4"nylocknut(J)ontoeachferrule,makingonly
nger tightatthistime.Seegure26.
FIGURE 26
J
BRACKET
CC
K
3
Y
H
Q
Q
J
J
2
W
U
F
12
FIGURE 29
APPLICATION TIPS
1. Tohelppreventcompactingandcloggingwhenusing
granularmaterial,avoidunnecessarytowingwhile
hopperislled.
2. Reducetheowsettingforspeedsslowerthan
3M.P.H.andincreasethesettingforhigherspeeds.
3. Toavoidmissesorstriping,overlapthepreviouspass
slightly.Spreadwidthisapproximately40".
4. Foreasiestapplication,rstapplymaterialacross
bothendsofthearea.Twoorthreepassesoneach
endaresufficient.Thenapplymaterialbackandforth
asshown.Usetheendareasforturningaround,
shuttingoffthespreaderasyouentertheendareas
andturningthespreaderonagainasyourleavethe
endareasforyournextpass.Seegure30.
5. Iflawnisoddshaped,spreadaborderaroundthe
edgesandthenspreadbetweentheborder.
6. Becarefulwhenspreadingaroundornamentalplants
becauseweedcontrolchemicalscandamagethese
plants.
PLASTIC
KNOB
FLOW RATE
SETTING (6)
0
1
2
4
6
FLOW CONTROL ARM
ON
OPERATION
HOW TO USE YOUR SPIKER/SPREADER
1. Refertotheinstructionlabelonthematerialpackage
andtotheinstructiondecalonyourspreadertohelp
determinetheproperspreadersettingandapplication
rate.AlsoseetheSettingChartonthispagefor
ageneralrangeofsettingsforcommonlyused
materials.
2. Loosentheknobandadjusttheowcontrolgaugeto
therecommendedsetting.Retightentheknob.See
gure29.
3. Determinetheapproximatesquarefootageofthearea
tobecoveredandestimatetheamountoffertilizeror
seedrequired.
4. Movethespiker/spreadertotheareawhere
applicationistobegin.
5. Makingsuretheowcontrolarmisinthe"OFF"
position,llthehopper,breakingupanylumps.
6. Lowertheaeratorspikestotheoperatingposition.
7. Startthespreaderinmotionandthenpulltheow
controlarmforwardtothe"ON"positionasyoutravel
acrossyourlawn.Therecommendedtowingspeedis
3m.p.h.
8. Donotmakesharpturnswithspikesintheground.
9. Raiseaeratorspikestotransportpositionwhen
crossingoverconcreteorotherhardsurfaces.
10.Donotaerateifthegroundisextremelyhardordry.
Ifgroundistoodry,sprinkleorwaterforonetotwo
hourspriortouse.
11. Donotaerateifthegroundistoowet(muddy).
IMPORTANT:Alwaysmoveowcontrolarmto"OFF"
positiontopreventexcessivereleaseoffertilizerwhen
stopping,turningorllingthespreader.
FIGURE 30
MAINTENANCE
1. Checknutsandboltsfortightnessbeforeeachuse.
2. Alwaysemptyhopperaftereachuse,storingleftover
materialinit'soriginalbag.
3. Washanddrythoroughlyaftereachuse.
4. Applyalightcoatofoilonexposedmetalpartstohelp
preventrust.
5. Atleastonceayear,applyafewdropsofoiltowheels
andtoplasticbearingsinspikedisks,atendsof
aeratorshaftandatendsofhoppershaft.
6. Cleanandoildrivechainonceayear.
Spike points are sharp. Exercise caution
whenworkingwithhandsnearspikedisks.
Flow Rate Setting
MATERIAL TYPE At 3 M.P.H.
SETTING CHART
Fertilizer Granular/Pelleted 0-1 / 0-2
GrassSeed Fine/Coarse 5-6 / 7-8
3M.P.H.isequivalenttotraveling100feetin23seconds.
13
B
21
6
22
8
8
10
9
5
11
13
8
15
18
8
23
21
8
12
8
8
4
D
2
5
5
6
1
7
4
3
21
8
6
8
20
21
6
14
17
21
21
26
25
24
SEE PARTS DIAGRAM ON PAGE 14
19
16
6
B
C
A
A
B
C
D
PARTS FOR 175 LB. POLY "PRO" SPIKER/SPREADER MODEL 45-0545
REF
NO.
PART NO. QTY DESCRIPTION
1 43848 1 PlasticGrip
2 24660 1 FlowControlArm
3 47712 1 FlowControlRod
4 47711 2 Ferrule
5 1543-69 3 NylonWasher
6 43088 8 Washer,1/4"
7 1509-90 1 Bolt,Hex1/4-20x1-1/4"Lg.
8 47189 22 Nut,Nylock1/4-20Thd.
9 63850 1 BraceAssembly,Hopper
10 24542 1 FlowControlGauge
11 43849 1 PlasticKnob,1/4-20Thd.
12 44950 1 Bolt,Carriage1/4-20x3/4"Lg.
13 43001 1 Bolt,Hex3/8-16x1"Lg.
REF
NO.
PART NO. QTY DESCRIPTION
14 47623 1 Pin,Hitch3/8"FlatHd.
15 23014 1 HitchBracket
16 24531 1 Tongue
17 43343 1 Pin,HairCotter#4(1/8")
18 HA21362 1 Nut,Nylock3/8-16Thd.
19 44326 2 Bolt,Carriage5/16-18x1"
20 1509-69 2 Bolt,Hex1/4-20x1-3/4"
21 43866 14 Bolt,Hex1/4-20x5/8"
22 43012 2 Bolt,Hex1/4-20x3/4"
23 24532 2 TongueBrace
24 47810 2 Nut,Nylock5/16-18
25 47707 1 HandleGrip
26 24647 1 TransportHandleBar
14
PARTS FOR 175 LB. TOW SPIKER SPREADER MODEL 45-0545
C
1
4
5
7
16
2
3
5
5
6
8
16
16
17
18
19
21
D
D
14
15
15
13
4
6
B
B
6
19
16
7
4
39
4
4
6
30
C
24
12
20
20
45
45
27
34
27
34
41
42
23
26
40
40
38
29
32
32
45
34
34
34
34
34
27
34
34
27
27
27
27
27
27
27
27
27
27
27
27
27
27
33
33
33
33
33
33
31
31
35
36
36
37
37
37
37
37
37
37
37
37
34
34
34
22
9
10
28
11
11
5
44
45
37
A
25
47
46
A
15
PARTS FOR 175 LB. TOW SPIKER SPREADER MODEL 45-0545
REF
NO.
PART NO. QTY DESCRIPTION
1 47451 1 Hopper
2 24536 1 HopperCenterPlate(Small)
3 24535 1 HopperCenterPlate(Large)
4 43088 9 Washer,1/4"
5 43866 4 Bolt,Hex1/4-20x5/8"
6 46978 6 Nut,Hex(SIMS)1/4-20Thd.
7 47615 2 Bearing,Flange
8 47484 1 Bearing,HexFlange
9 24538 1 Bracket,FeedPlate(RH)
10 24539 1 Bracket,FeedPlate(LH)
11 63949 1 Axlew/Sprocket,5/8"
12 728-3001 10 PopRivet
13 47459 1 Skirt,48"
14 47508 1 SkirtRetainer
15 24537 2 FlowPlate
16 43009 10 Washer
17 47259 4 AgitatorBlade
18 47978 16 Screw,#8-32x1/4"Lg.
19 63948 1 Axlew/Sprocket,3/4"
20 46838 2 Spacer,.76"x1.0"x0.50"
21 47458 2 Spacer,1.25"ODx.330"Lg.
22 65790 1 HopperFrameAssembly
23 41863 2 Wheel
24 1509-69 2 Bolt,Hex1/4-20x1-3/4"
REF
NO.
PART NO. QTY DESCRIPTION
25 26007 2 StepBushing(Special)
26 69441 1 LiftTubeAssembly
27 741-0249 18 Bearing,Flanged0.63"I.D.
28 47684 1 ChainwithConnector
29 48106 2 Bolt,Shoulder3/8-16x5/8"
30 43082 2 Nut,HexLock3/8-16
31 24648 2 CenterBrace
32 47777 2 CompressionSpring
33 47683 6 Spacer,.75"x1.0"x2.98"
34 R19212016 12 Washer,21/32x1-1/4x16ga.
35 47782 1 Spacer,1.0"IDx3.25"
36 69416 2 DriveDiskAssembly
37 28606 10 SpikeDisk(7")
38 45100 2 Bolt,Hex1/2-13x4"
39 47189 2 Nut,Nylock1/4-20
40 R19171616 4 Washer,17/32"x1"x16ga.
41 48115 2 NylockHexJamNut,1/2"
42 43019 2 Nut,HexJam1/2-13
43 HA24629 2 Tie,Plastic30"(notshown)
44 47679 1 ChainCover
45 43093 4 CotterPin,1/8"x1-1/2"
46 48840 6 Screw,1/4-20x1/2"
47 26005 2 AxleRetainerBracket
45601 1 OwnersManual
the fastest way to purchase parts
www.speedepart.com
REPAIR PARTS
Agri-Fab,Inc.
809SouthHamilton
Sullivan,IL.61951
217-728-8388
www.agri-fab.com
the fastest way to purchase parts
www.speedepart.com
Thisdocument(ormanual)isprotectedundertheU.S.CopyrightLawsandthecopyrightlawsofforeigncountries,
pursuanttotheUniversalCopyrightConventionandtheBerneconvention.Nopartofthisdocumentmaybereproduced
ortransmittedinanyformorbyanmeans,electronicormechanical,includingphotocopyingorrecording,orbyany
informationstorageorretrievalsystem,withouttheexpresswrittenpermissionofAgri-Fab,Inc.Unauthorizedusesand/or
reproductionsofthismanualwillsubjectsuchunauthorizedusertocivilandcriminalpenaltiesasprovidedbytheUnited
StatesCopyrightLaws.
©2000Agri-Fab,Inc.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Agri-Fab 45-0545 User manual

Category
Spreader
Type
User manual

Agri-Fab 45-0545 is a 175 LB Tow Spiker Spreader, a versatile tool designed to enhance lawn care and maintenance tasks. Its robust construction and efficient design make it suitable for various applications.

With its 175-pound towing capacity, the spreader can effortlessly handle large quantities of lawn chemicals, ensuring even and precise distribution. The spiker disks effectively penetrate the soil, creating channels for the chemicals to reach the roots of the grass, promoting healthy growth and preventing weeds.

The adjustable flow control mechanism allows for customization of the spreading rate, adapting to different lawn sizes and chemical requirements. The hopper's generous capacity enables extended use without frequent refilling, maximizing efficiency and minimizing interruptions.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI