Barco Galaxy NH-12 Installation guide
- Category
- Projectors
- Type
- Installation guide
This manual is also suitable for
Lamp kit
Installation manual
SIM 10 / NW-series / NH-12 series / LH-12 series
R9843087
R9843097
R5977691/01
25/05/2012
Barco nv Control Rooms & Simulation Division
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.82.11
Fax: +32 56.36.84.86
Support: www.barco.com/esupport
Visit us at the web: www.barco.com
Printed in Belgium
Changes
Barco p rovides this manua l ’as is’ without warranty of any kind, either e xpressed or implied, including but not limited to the implied w ar-
ranties or m erchantability and fitness for a particular purpose. Barco may make improvements and/or cha nges to the product(s) and/or the
program(s) described in this publication at any time without n otice.
This publication could c ontain technical inaccuracies or typographical errors. Changes are periodically m ade to the information in this
publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Bar co web site w
ww.bar co.com or from the secured B arco web site
h
ttps://my.barco.com.
Copyright ©
All rights r eserved. No part of this documen t may be copied, reproduced or translated. It s hall not otherwise be recorded, transmitted or
stored in a retrieval s ystem without the prior written consent of Barco.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide r easonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and , if not installed and used in accordance w ith
the instruction m anual, may cause harmful interference to radio com munications. O peration of this equipm ent in a residential area may
cause harm ful interference, in which case the us er will be responsible for correcting any interference at his own expense
Guaran tee and Compensation
Barco provides a guarantee relating to perfect man ufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for dam age inc urred during transport, a s well as for material and manufacturing faults Barco
must be informed immediately in writing of any c omplaints.
The period of gu arantee begins on the date of transfer of risks, in the case of special systems and software on the date of comm issioning,
at latest 30 days after the transfer of risks. In the ev ent of justified notice of com plaint, Barco can r epair the fault or provide a replac ement
at its own discretion within an appropriate period. If this m ea
sure proves to be impossible or uns uccessful, the purchaser ca n deman d a
reduction in the purchase pr ice or c ancellation of the contract. All other claims, in par ticular th ose relating to compensa tion for direct or
indirect damage, and also damage attributed to the operation of s oftware as well as to other services provided by Barco, being a component
of the s ystem or independent service, will b e deemed inval
id provided the damage is not pro ven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gr oss negligence or part of Bar co.
If the purchaser or a third party carries out modifications or repairs o n go ods delivered by Barco, or if the goods are ha ndled inc orrectly,
in particular if the systems a re commiss ioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not
agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are
system failures which are attributed to programs or special electronic circuitry pr ovided by the purchaser, e.g. interfaces. Normal wear as
well as normal maintenance a re not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be com plied with by
the customer.
Trademarks
Brand and product name s m entioned in this m anual m ay be tradem arks, registered trademarks or c opyrights of their respective holders.
All brand and produc t names mentioned in this man ual serve as commen ts or examples and are not to be understood as adv ertising for
the products or their manufacturers.
Turkey RoHS compliance
Türkiye Cumhuriyeti: EEE Y önetm eliğine Uygundu r.
[Republic of Turkey: In conformity with the EEE Regulation]
Table of contents
TABLE OF CON TENTS
1. Safety................................................................................................................. 3
1.1 Safety Guidelines..................................................................................................................... 3
1.2 Recycling guidelines.................................................................................................................. 3
2. Lamp kit description............................................................................................... 5
2.1 Kit description......................................................................................................................... 5
2.2 Kit content ............................................................................................................................ 5
3. Lamp replacement on SIM 10 .................................................................................... 7
3.1 Lamp removal......................................................................................................................... 7
3.2 Lamp installation.....................................................................................................................10
4. Lamp replacement on NW–12 and NH–12 platform .........................................................15
4.1 Removing the rear cover ............................................................................................................15
4.2 Removing the fan outlet .............................................................................................................16
4.3 Removing the lamp..................................................................................................................17
4.4 Installing the lamp ................................................................................................................... 18
4.5 Installing the fan outlet ..............................................................................................................19
4.6 Installing the rear cover .............................................................................................................20
Index......................................................................................................................23
List of images...........................................................................................................25
R5977691 LAMP KIT 25/05/2012 1
Table of contents
2 R5977691 LAMP KIT 25/05/2012
1. Safety
1. SAFETY
Introduction
Read all warnings and cautions attentively wherever mentioned in this ma nual. This to prevent pers onal injury wh en r eplacing a
Xenon lamp of the SIM 10 projector.
1.1 Safety Guidelines
This procedure is intended for use only by qualified service technicians wh o have been trained and authorized
by B arco!
WARNING: Ho t Surface and Risk of Explosion: Switch the projector to stand by and let it cool down for at least
15 minutes. These lamps cons ist o f a quartz arc tube operating at very high t emp erature a nd high pressu re
which m ay explode suddenly. There is a risk of personal injury and property damage from hot quartz arc tube
particles if h and led incorrectly.
WARNING: Risk of Electrical Shock: Power down the projector and unplug the power cord from the wall
outlet. Once the projector is cooled down and the power is off, continue with the procedure.
WARNING: Lamp Runtime Warning: Do n ot exceed the indicated maximum total lifetime of the lamp for safe
operation in normal power mode. Do not use it longer ! A lways replace the lamp with the BA RCO lamp kit.
WARNING: U V Radiation Exposure : Never light the lamp if the top-rear cover of the projector is removed.
CAUTION: Do not touch the front glass cover of the lamp with your fingers, since this w ill reduce the lamp
output of the lamp.
If the front glass cover of the lamp has been touched, finger prints can be wiped off using alcohol.
1.2 Recycling guidelines
CAUTION: To avoid breaking the lamps, repack carefully wh en storing and transporting them.
R5977691 LAMP KIT 25/05/2012 3
1. Safety
CAUTION: Lamps may not be disposed as normal household trash.
Contact your local w aste disp osal facility for information on the recycling program for HID (High Intensity
Discharge ) lam ps in your area.
Image 1-1
Disposal options for Xenon-lamps
• Recycle through a municipal or solid waste district household hazardous waste collecti
on program in accordance with local
regulations.
• Direct shipment to lamp recycler
• Shipment through a hazardous waste transporter
4 R5977691 LAMP KIT 25/05/2012
2. Lamp kit description
2. LAMP KIT DESCR IPTION
For the late s t vers io n of thi s install ation manual, see www.barco.com (public) or https://my.barco.com (se-
cured) or Intranet (Barco employ ees only).
CAUTION: This procedure may only be p erformed by a qualified technician.
Overview
• Kit description
• Kit content
2.1 Kit description
Xenon lamp
A xenon lamp use s ionize d x enon gas to produce a bright white light which clos ely s imulates natural bright daylight.
Description
When order ing a lamp, we can distinguish two situations.
• A used lamp is returned to Barco at or der time.
In this case, kit R9843087 (Refurbished lamp) can be ordered.
• No u sed lamp is returned to Barco at order time.
In this c ase, kit R9843097 (New lamp) can be ordered.
Scope
This kit is designed to be used in the following projectors:
• SIM 10;
• Galaxy NW -12;
• NW-12;
• Galaxy NH-12;
• NH-12;
• iD LH-12;
• iCon NH-12.
2.2 Kit content
Kit content
Kit number Description
Quantity
2.0 kW re furbished X enon lamp
1
R9843087
Installation manual 1
2.0 kW new X enon lam p 1R9843097
Installation manual 1
R5977691 LAMP KIT 25/05/2012
5
2. Lamp kit description
Image
Image 2-1
1 Cathode
2 Anode
3 Lamp info connector
6 R5977691 LAMP KIT 25/05/2012
3. Lamp replacement on SIM 10
3. LAMP REPLACEMENT ON SIM 10
Overview
• Lamp remova l
• Lamp installation
3.1 Lamp removal
Necessary tools
Slotted screwdriver
Remove the lamp
1. Release the screws fix ing the top-rear cover to the p rojector.
90°
Image 3-1
Top-rear cover: releasing
2. Remove the top-rear cover by pulling it away (i.e. backside) from the projector.
Image 3-2
Top-rear cover: removal
3. Release the screws fixing the rear light screen to the projec tor.
R5977691 LAMP KIT 25/05/2012
7
3. Lamp replacement on SIM 10
90°
Image 3-3
Rear light screen: releasing
4. Lift the rear light screen to remove it.
Image 3-4
Rear light screen: removal
5. Release the screws fixing the lamp to the projector frame.
8
R5977691 LAMP KIT 25/05/2012
3. Lamp replacement on SIM 10
Image 3-5
Lamp: releasing
6. Use the rear s ide handle of the lamp to pull it until the lamp feet are in line with the slider slots.
Image 3-6
Lamp removal: slide the lamp out, u
ntil it c an be lifted
R5977691 LAMP KIT 25/05/2012 9
3. Lamp replacement on SIM 10
Image 3-7
Lamp removal: slide the lamp out, until it can be lifted
1 Pull the lamp a bit
2 Lampfeetinlinewithsliderslots
7. Use the top handle to lift out the lamp.
Image 3-8
Lamp removal: lift to rem ove
3.2 Lam p installation
Necessary tools
Slotted screwdriver
Install the lamp
1. Position the lamp: the lamp feet must be in line with t he s lider slots.
10
R5977691 LAMP KIT 25/05/2012
3. Lamp replacement on SIM 10
Image 3-9
Lamp installation: move the lamp to the correct position
Image 3-10
Lamp installation: move the lamp to the correct position
Image 3-11
Lamp installation: move the lamp to the correct position
1 Lamp feet
2 Lamp slider slots
3 Lampfeetinlinewithsliderslots
2. Push do wn the lam p until its feet are fully down in the slider.
R5977691 LAMP KIT 25/05/2012
11
3. Lamp replacement on SIM 10
Image 3-12
Lamp: insertion in slider
3. Push the lamp to plug in the following connectors (confirm ed by the click sound)
- cathode;
- anode;
- lamp info connector (at the front bottom side of the lamp).
Image 3-13
Lamp: connection
Caution: If the lamp does n’t slide in s moothly,
gently wiggle it until it does.
Since the lam p info connector has some bac klash, it might not be fully in line w ith its plug (especially if the p rojector
is not in table mode) making it hard to get it conn ected. By wiggling the lamp, the correct alignment of the lam p info
connector can be easily achieved.
Caution: Make sure not to push away the projector while pushing the lamp.
4. Fix the lamp by han d tightening bo th two screws.
12
R5977691 LAMP KIT 25/05/2012
3. Lamp replacement on SIM 10
Image 3-14
Lamp: fixation
5. Put the rear light screen in its co rrect position and fix it (tw o screws).
Image 3-15
Rear light screen: installation
90°
Image 3-16
Rear light screen: fixation
6. Put the top-rear cover in its correct position and fixit(threescrews).
R5977691 LAMP KIT 25/05/2012
13
3. Lamp replacement on SIM 10
Image 3-17
Top-rear cover: installation
90°
Image 3-18
Top-rear cover: fixation
14 R5977691 LAMP KIT 25/05/2012
4. Lamp replacement on NW–12 and NH–12 platform
4. LAMP REPLACEMENT ON NW–12 AND NH–12
PLATFORM
Introduction
This chapter des cribes the lamp replacement procedure in the following pro jectors:
• Galaxy NW -12;
• NW-12;
• Galaxy NH-12;
• NH-12;
• iD LH-12;
• iCon NH-12.
Overview
• Removing the rear cove r
• Removing the fan outlet
• Removing the lamp
• Installing the lamp
• Installing the fan outlet
• Installing the rea r cover
4.1 Removing the rear cover
Necessary tools
Philips Ph2
How to remove the rear cover?
1. Remove the fix ing screw
Image 4-1
Rear cover: fixing screw
2. Lift the back side of the rear cove r and pull it backward to remove it
R5977691 LAMP KIT 25/05/2012
15
4. Lamp replacement on NW–12 and NH–12 platform
Image 4-2
Tilt the back side of t he rear cover
Image 4-3
Pull the rear cover backward
Image 4- 4
Rear cover removed
4.2 Removing the fan outlet
Necessary tools
Slotted screwdriver 5 mm
How to remove the fan outlet?
1. Remove the rear cover ( see concerning chapter)
2. Remove the fixing screw of the fan outlet
Image 4-5
Fan outlet: fixing screw
3. Take out the fan outlet by lifting it
Image 4-6
Fan outlet: lift to remove
16 R5977691 LAMP KIT 25/05/2012
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
Barco Galaxy NH-12 Installation guide
- Category
- Projectors
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco Galaxy NW-7 EX Installation guide
-
Barco Galaxy 4K-12 User manual
-
Barco iQ Pro R500 Owner's manual
-
-
Barco iCon H600 lamp kit (300W UHP) Installation guide
-
-
-
-
-
Barco NW-12 User guide
