INSTALLATION INSTRUCTIONS
electri
Center
ACCESSORIES
Hazardous Voltage.
Will cause death,
serious injury or substantial
property damage.
Turn off power supplying this
equipment before working inside.
SAFETY INSTRUCTIONS
DANGER
600636C Rev.X
1. Turn off and lock off the power supplying this enclosure before working
inside.
2. To install, press the padlocking assembly onto the circuit breaker (Fig.1).
(The barbs on the lock mount will cause this to be a snug fit).
3. The circuit breaker can be locked in the "OFF" or "ON" position. Once
the padlocking assembly is installed, the lock plate must be rotated to
allow access to the circuit breaker handle(s) (Fig.2).
ECPLD2P
CATALOG NUMBER
2" Wide - Padlocking Device
This kit fits SIEMENS and MURRAY breaker types:
BAF, BAFH, BE, BG, BLE, BLEH, BLF, BLG,
BLHF, BQ, BQAF, BQAFH, BQH, BQXD, HBQ,
HQP, MG, MH-T, MP-AT, MP-ET, MP-GT,
MP-HAT, MP-HET, MP-HGT, MP-HT, MP-MT,
MP-T, MW, QAF, QAFH, QE, QEH, QG, QP,
QPF, QPH, QPHF, QT, QW.
Package contains 3 devices.
Same As:
ECPLD2, PLD2
Note: This instruction outlines the
recommended installation procedure.
BARBS
FIG. 1
FIG. 2
BARBS
0 140892 09061
INSTALLATION INSTRUCTIONS
electri
Center
ACCESSORIES
40783643454833
Siemens Industry, Inc. Norcross, Georgia U.S.A. Assembled in Mexico
© 2007 Copyright Siemens Industry, Inc.
Hazardous Voltage.
Will cause death,
serious injury or substantial
property damage.
Turn off power supplying this
equipment before working inside.
SAFETY INSTRUCTIONS
DANGER
600636A Rev.X
1. Turn off and lock off the power supplying this enclosure before working
inside.
2. To install, press the padlocking assembly onto the circuit breaker (Fig.1).
(The barbs on the lock mount will cause this to be a snug fit).
3. The circuit breaker can be locked in the "OFF" or "ON" position. Once
the padlocking assembly is installed, the lock plate must be rotated to
allow access to the circuit breaker handle(s) (Fig.2).
ECPLD2
CATALOG NUMBER
2" Wide - Padlocking Device
This kit fits SIEMENS and MURRAY breaker types:
BAF, BAFH, BE, BG, BLE, BLEH, BLF, BLG,
BLHF, BQ, BQAF, BQAFH, BQH, BQXD, HBQ,
HQP, MG, MH-T, MP-AT, MP-ET, MP-GT,
MP-HAT, MP-HET, MP-HGT, MP-HT, MP-MT,
MP-T, MW, QAF, QAFH, QE, QEH, QG, QP,
QPF, QPH, QPHF, QT, QW.
Package contains 3 devices.
Same As:
PLD2
Note: This instruction outlines the
recommended installation procedure.
BARBS
FIG. 1
FIG. 2
BARBS
INSTALLATION INSTRUCTIONS
electri
Center
ACCESSORIES
Hazardous Voltage.
Will cause death,
serious injury or substantial
property damage.
Turn off power supplying this
equipment before working inside.
SAFETY INSTRUCTIONS
DANGER
600636A Rev.X
1. Turn off and lock off the power supplying this enclosure before working
inside.
2. To install, press the padlocking assembly onto the circuit breaker (Fig.1).
(The barbs on the lock mount will cause this to be a snug fit).
3. The circuit breaker can be locked in the "OFF" or "ON" position. Once
the padlocking assembly is installed, the lock plate must be rotated to
allow access to the circuit breaker handle(s) (Fig.2).
ECPLD2R
CATALOG NUMBER
2" Wide - Padlocking Device
This kit fits SIEMENS and MURRAY breaker types:
BAF, BAFH, BE, BG, BLE, BLEH, BLF, BLG, BLHF,
BQ, BQAF, BQAFH, BQH, BQXD, HBQ, HQP, MG,
MH-T, MP-AT, MP-ET, MP-GT, MP-HAT, MP-HET,
MP-HGT, MP-HT, MP-MT, MP-T, MW, QAF, QAFH,
QE, QEH, QG, QP, QPF, QPH, QPHF, QT, QW.
Package contains 3 devices.
Same As:
ECPLD2, PLD2
Note: This instruction outlines the
recommended installation procedure.
BARBS
FIG. 1
FIG. 2
BARBS
7 883643 49637
NOTES:
1. 1-SIDED INSTRUCTION SHEET
2. PRINT COLOR: BLACK
3. MATERIAL: PER SPEC 4080190
PART NO. 600636A PART NO. 600636B PART NO. 600636C
REVISIONS
REV. DESCRIPTION ECN NO. DATE
OF
REV.
APPROVED
THIRD ANGLE PROJ.
DO NOT SCALE DRAWING
ANGULAR ±
.XXX ±
.XX ±
TOLERANCES:
DIMENSIONS ARE IN INCHES
UNLESS OTHERWISE SPECIFIED
Siemens Industry, Inc.
CONFIDENTIAL- PROPERTY OF Siemens Industry, Inc.
.12
SHEET
SCALE
DWG NO.
FSCM NO.
SIZE
DATE
APVD
DATE
CHK
DATE
DWN
CORELDRAW FILE:
B
1:1
INSTRUCTION SHEET
600636
4
12/03/03O.RANGEL
12/04/03B.GARCIA
12/05/03B.GARCIA
2 ITEM A, UPC 40783643454833 WAS
783643454835.
07-243J1 02/12/08 OO
3 ADDED ITEM 600636C 08-204NC 11/20/08 RS
1 ADDED ITEM 600636B 05-150NC 04/12/07 DV
11
WHERE “X” DENOTES
REVISION LEVEL
5.50"
4.25"
5.50"
4.25"
WHERE “X” DENOTES
REVISION LEVEL
5.50"
4.25"
WHERE “X”
DENOTES
REVISION
LEVEL
4
CHANGED "SIEMENS ENERGY & AUTOMA-
TION" FOR "SIEMENS INDUSTRY, INC.
CHANGED "CIRCUIT PROTECTION & CON-
TROL DIVISION" FOR "SIEMENS BUILDING
TECHNOLOGIES" CHANGED "ALPHARETTA"
FOR "NORCROSS"”
02/16/10
R. Martinez
10-010J1
Siemens Industry, Inc. Norcross, Georgia U.S.A. Assembled in Mexico
© 2007 Copyright Siemens Industry, Inc.
© 2007 Copyright Siemens Industry, Inc.
Siemens Industry, Inc. Norcross, Georgia U.S.A. Assembled in Mexico
Released Production, 4 v1, Feb 26, 2010
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Siemens ECCS2 Operating instructions
-
-
-
-
-
-
-
-
-
