Gerni Super 130.3 User manual

Brand: Gerni

Model: Super 130.3

Category: High-pressure cleaners

Type: User manual

This manual is also suitable for

Gerni Super 130.3 is a high-pressure washer designed for domestic use. It features a powerful motor and a variety of nozzles for different cleaning tasks. With a maximum pressure of 130 bar and a flow rate of 500 l/h, it can easily remove dirt and grime from cars, bikes, boats, patios, and more. The Super 130.3 also comes with a range of accessories, including a detergent bottle and a patio cleaner, making it a versatile cleaning solution for a variety of tasks.

128332556 d (12.2015)

Super 130.3

Super 135.3

Super 140.3

Super 145.3

User Guide

Printed in China

3Original Instructions

Contents

1 Introduction .................................................................................................. 4

1.1 Symbols used to mark instruction .......................................................................4

2 Safety precautions and working techniques ................................................4

3 Before you start using your high pressure washer ................................ 10

3.1 Mounting of trolley handle, hose hook and hose reel .......................................10

3.2 Mounting of quick coupling ...............................................................................10

3.3 Telescopic handle .............................................................................................10

4 Operating your high pressure washer ..................................................... 11

4.1 Connection of high pressure hose ....................................................................11

4.2 Mounting of spray lance and Click&Clean nozzles ...........................................11

4.3 Water Connection .............................................................................................11

4.4 Starting the high pressure washer ....................................................................12

4.5 Pressure regulation on the TORNADO® PR- nozzle .........................................12

4.6 Stationary use ...................................................................................................12

5 Fields of application and working methods ............................................ 13

5.1 General .............................................................................................................13

5.2 Typical ﬁ elds of application ...............................................................................14

6 After using the pressure washer .............................................................. 15

6.1 Stopping the high pressure washer ..................................................................15

7 Maintenance ............................................................................................... 15

8 Troubleshooting ......................................................................................... 16

9 Accessories and detergents ..................................................................... 17

10 Warranty Conditions ................................................................................. 17

11 Main technical Data ................................................................................... 18

12 Declaration of Conformity ......................................................................... 19

Original Instructions

1 Introduction

1.1 Symbols used to mark instruction

All pictograms attached to the high pressure washer and its components are shown and ex-

plained in this manual.

Safety instructions marked with this symbol must be observed to prevent personal injury or

serious damage to property.

Caution where there is a risk of damaging the machine or its individual components.

This symbol indicates tips and instructions to simplify work and to ensure a safe operation of

the high pressure washer.

2 Safety precautions and working techniques

Before starting up your machine for the ﬁ rst time, this instruction manual must be read through

carefully. Save the instructions for later use.

WARNING!

• Inhalation of aerosols can be hazardous to health.

Where applicable use a device in order to avoid or re-

duce aerosols production, e.g., a shield covering the

nozzle. For protection against aerosols use a respira-

tory mask of class FFP 2 or higher.

• The high water pressure generated by the machine

and the power connection are particular sources of

danger.

• Machines shall not be used by children or untrained

personnel. Children should be supervised to ensure

that they do not play with the machine.

• Do not use the machine within range of persons un-

less they wear protective clothing.

• Before starting up your machine please check it care-

fully for any defects. If you ﬁ nd any, do not start up

your machine, contact your Gerni distributor. The in-

sulation of the electric cable should be faultless and

without any cracks. If the electric cable is damaged,

an authorized Gerni di stributor should replace it.

• Always unplug the power plug before cleaning or

maintenance and when replacing parts or converting

the machine to another function.



5Original Instructions

• Observe the national safety regulations issued, for

example, by the employers liability insurance associa-

tion, social security institutions, occupational safety

and health authorities or other organizations.

Accessories and spare parts

• To ensure the machine safety only use original spare

parts from Gerni or approved by Gerni.

• High pressure hoses, ﬁ ttings and couplings are impor-

tant for the safety of the machine. Only use hoses, ﬁ t-

tings and couplings recommended by Gerni.

Physical, sensory or mental conditions

• This machine is not intended for use by persons

(including children) with reduced physical, senso-

ry or mental capabilities or lack of experience and

knowledge. If the machine is used by people with re-

duced physical, sensory or mental capabilities or lack

of experience and knowledge they shall have been

given supervision or instruction concerning use of the

machine in a safe way and understand the hazards in-

volved.

Applications

This machine has been developed for domestic use

such as:

• Car, motorbike, boat, caravan, trailer, patio/drive/ﬂ ag-

stones, woodwork, brickwork, barbecue, garden furni-

ture, lawn mower.

Any other use is considered as improper use. Gerni ac-

cepts no liability for any damage resulting from such

use. The risk for such use is borne solely by the user.

Proper use also includes proper operation, servicing

and repairs as speciﬁ ed in this instruction.

Clothing and equipment

Always take action to protect yourself when operating

the machine.

• Wear shoes with non-slip soles.

• Wear goggles, ear protection and protective clothes



Original Instructions

during operation.

Transporting the high pressure washer

• When transporting the machine in or on a vehicle, it

must be secured, e.g. with straps, so that it cannot slip

or tip over.

• Gerni recommends that the machine is positioned

horizontally on the backside, when transported in or

on a vehicle.

Detergents

• This machine has been designed for use with clean-

ing agents supplied or recommended by Gerni. The

use of other cleaning agents or chemicals may ad-

versely affect the function of the machine.

 Before starting the work

Inspecting the machine

• Do not use the machine if a supply cord or important

parts of the machine are damaged, e.g., safety de-

vice, high pressure hose, and spray handle and spray

attachments.

• The trigger of the spray handle must move easily and

automatically return to its starting position when re-

leased.

• Always keep high pressure hose and spray attach-

ment in good condition (clean, moving easily) and cor-

rectly assembled.

Electrical connection

WARNING!

Minimize the risk for electrical shock:

• Voltage and frequency of the machine (see rating

plate) must match the voltage of and frequency of the

mains supply.

• Only connect the machine to electrical installation

made by a certiﬁ ed electrician and com ply with IEC

60364-1.

• It is recommended that the electrical supply to the



7Original Instructions

machine should include a residual current device that

will interrupt the supply if the leakage current to earth

exceeds 30 mA for 30 ms.

• Inadequate extension cables can be dangerous. If an

extension cable is used, it shall be suitable for outdoor

use, and the connection has to be kept dry and off the

ground.

• Gerni recommends use of an extension cable drum

when cable extension is needed which keeps the

socket at least 60 mm above the ground.

• If the electric cable is damaged, it must be replaced

by an authorized Gerni distributor or similar qualiﬁ ed

person in order to avoid a hazard.

Water connection

• This high pressure washer is only allowed to be con-

nected with the drinking water mains, when an appro-

priate backﬂ ow preventer has been installed, Type BA

according to EN 60335-2-79.

• The backﬂ ow preventer can be ordered under number

106411177.

• As soon as drinking water has ﬂ own through the back-

ﬂ ow preventer, it is no longer regarded as drinking

water.

• Operation by suction (e.g. a rainwater vessel) is car-

ried out without a backﬂ ow preventer – see “Connec-

ting to a pressureless water supply”. The machine

can be connected to water mains with a max. inlet-

pressure of 1 MPa/10 bars and max. 60°C.

Safety devices

Locking device on spray handle:

• The spray handle features a locking device. When the

pawl is activated, the spray handle cannot be ope-

rated.

Thermal sensor:

• A thermal sensor protects the motor against overload-

ing. The machine will restart after a few minutes when

the thermal sensor has cooled.

Original Instructions

Pressure safety device:

• An integrated hydraulic safety valve protects the

system from excessive pressure.

During work

WARNING!

• It is not allowed to clean asbestos-containing surfaces

with high pressure.

• Risk of explosion – Do not spray ﬂ ammable liquids.

• Never draw in ﬂ uids containing solvents (e.g., gaso-

line, heating oil, paint thinner or acetone) These sub-

stances damage the materials used in the machine.

Their spray is highly combustible, explosive and poi-

sonous.

• Never direct the water jet at yourself, other persons,

not even to clean clothing or footwear - risk of injury.

• Never direct the water jet at pets or other animals.

• Never direct the water jet at live electrical equipment

or the machine itself - danger of short-circuiting.

• The spray lance is affected by a kickback force less

than 20N and a sudden torque when activating the

trigger of the spray handle during operation.

• This high pressure washer machine must not be

operated at temperatures below 0°C.

• Never start up a frozen machine. Frost damages are

not covered by the guarantee!

• Always ensure ﬁ rm and safe footing.

• The machine shall be operated in an upright position.

• If the machine is left or not used for 5 minutes, it must

be switched off on the start/stop switch "O" (1).

After ﬁ nishing the work

WARNING!

• Always switch off the machine and unplug the power

plug from the socket after work and when leaving the

machine unattended.

• Disconnect water inlet hose between machine and

9Original Instructions

water supply.

• Always empty pump, hose and accessories of water

after use of the machine and prior to storing.

Maintenance and repairs

WARNING!

• Always disconnect the electrical plug from the socket

prior to maintenance, cleaning and repair.

• Any repair should always be made in Gerni autho rized

workshop with original Gerni spare parts.

• Do not attempt any maintenance not described in the

instructions.

• If the machine refuses to start, stops, pulsates, pres-

sure ﬂ uctuates, motor busses, fuse blows or no wa-

ter comes out, check the trouble shooting diagram

in these instructions. In case other problems occur,

please contact your local Gerni distributor.

Recycling the high pressure washer

Make the old machine unusable immediately.

• Unplug the machine.

• Cut the electric cable.

Do not discard electrical appliances with household

waste. As speciﬁ ed in WEEE Directive 2012/19/EC on

old electrical and electronic appliances, used electrical

goods must be collected separately and recycled eco-

logically. Contact your local authorities or your nearest

dealer for further information.

Original Instructions

3 Before you start using your high pressure washer

See the pictorial quick reference guide – unpacking.

Illustration shows the operation elements and how to prepare your machine for use.

Operation elements

1. Start/stop switch

2. Water inlet with ﬁ lter

3. High pressure connection (models without hose reel)

4. High pressure hose

5. Electric cable

6. Click&Clean spray lance

7. Spray handle with lock (7a)

8. Click&Clean Tornado PR nozzle

9. Click&Clean Powerspeed nozzle

10. Foam sprayer

11. Nozzle cleaning tool

12. Hose reel (not standard)

13. Model tag

14. Trolley handle (telescopic handle)

15. Hose hook

16. Hexagon key for handle and bracket mounting

17. Button for telescopic handle

18. Turnable cable hook

19. Quick coupling

3.1 Mounting of trolley handle, hose hook and hose reel

Mounting of trolley handle and hose hook (standard models)

A1 Push down the trolley handle (14) over the two metal tubes. Make sure that the handle

is mounted as illustrated. Mount screws with nuts (make sure that the screws go through

handle as well as tube).

A2 Mount the hose hook (15) on the handle (2 screws).

Mounting of hose reel handle (models with hose reel)

A3 Click the hose reel handle on to the trolley handle (no screws).

3.2 Mounting of quick coupling

A4 When mounting the quick coupling for the ﬁ rst time, check that the factory ﬁ tted ﬁ lter is

positioned in the water inlet pipe.

A5 Screw the quick coupling tight on to the water inlet (2).

IMPORTANT!

The inlet ﬁ lter must always be ﬁ tted in the water inlet pipe to ﬁ lter out sand, lime stone and other

impurities as these will damage the pump valves. The ﬁ lter is factory ﬁ tted.

If the ﬁ lter is removed this will invalidate the guarantee.

3.3 Telescopic handle

A6 The machine features a tele scopic handle. To raise or lower the handle, press the button

(17) and move the handle upwards or downwards. When a click is heard, the handle is in

right position.



11Original Instructions

4 Operating your high pressure washer

See the pictorial quick reference guide – operating your high pressure washer.

4.1 Connection of high pressure hose

B1 Attach the high pressure hose (4) to the spray handle (7). Detach the high pressure hose

by pressing the pawl (A).

B2 Mount the high pressure hose on the outlet (3).

4.2 Mounting of spray lance and Click&Clean nozzles

B3 Push the spray lance (6) into the spray handle (7), twist and release.

NOTE!

The spray lance has a built-in low pressure nozzle that can be used for ﬂ ushing away

dirt.

B4 When attaching the nozzles (8, 9), press the nozzles into the spray lance.

IMPORTANT!

When attaching the click & Clean nozzles, the pawl on the side of the spray lance should come

out again. The nozzle should stay in position when pulling it.

B5 Push the foam sprayer (10) into the spray lance (6).

NOTE!

The foam sprayer features a swivel lock, which must be positioned in the hole in the Click &

Clean spray lance. Press the pawl to detach the Click & clean nozzles and the foam sprayer.

IMPORTANT!

Before starting the cleaning job, check that the machine is in an upright position and placed on

an even surface. Do not place the machine in long grass!

4.3 Water Connection

IMPORTANT!

Connecting to pressurized water supply

The inlet water max. pressure is 1 MPa/10 bar and the max. temperature is 60°C – see rating

plate. An ordinary ½" garden hose of min. 10 m and max. 25 m will be suitable.

B6 Check that the ﬁ lter is ﬁ tted in the water inlet pipe and that it is not clogged up.

B7 Connect the water hose to the water supply by means of the quick connector. Turn on the

water.

Connection to the drinking water mains according to national and local regulations.

Let the water run through the water hose before connecting it to the machine to prevent sand

and dirt from penetrating the machine.

B8 Turn off the water and connect the water hose by means of the quick coupling to the wa-

ter inlet.

Connecting to pressure less water supply

The machine can also operate in suction mode, meaning that you can connect the machine to

e.g. rainwater vessels, rivers, lakes and cisterns etc. When taking in water from non drinking

water mains the backﬂ ow preventer is not needed.



Original Instructions

When connecting the machine to operate from pressure less water supplies – always use ad-

ditional ﬁ ltering to secure that impurities are not sucked in. Hose length should be max. 3 meter

and of minimum ½".

To meet these requirements, Gerni recommends that you use the original Gerni suction Hose

kit.

The Machine is designed for suction up to 100 cm above water surface.

• Position the machine at max. 1.0 meter above the water surface. Detach the high pressure

hose from the outlet.

• Ensure that the inlet ﬁ lter is in position and attach the suction hose kit, secure tight connec-

tion to the inlet.

• Turn on the machine, turning the start/stop switch (1) to position "I".

• Wait until a steady jet exits the outlet.

• Switch off the machine and attach high pressure hose (4), spray handle, lance and nozzle.

• Start the machine again and activate the spray handle.

4.4 Starting the high pressure washer

IMPORTANT!

Connecting to mains power supply

The voltage and frequency of the machine (see model tag (13)) must match the voltage and

frequency of the power supply.

Connecting the high pressure washer to a supply system, the max allowed impedance is =

0,29+j0,18 (Zmax). Consult with the supply authority that the equipment is connected only to

a supply of that impedance or less.

B9 Insert the power plug into power supply socket.

B10 Turn on the water.

B11 Release the trigger lock (7a). Remember to unplug, turn off the high pressure washer and

lock the trigger, when leaving the high pressure washer unattended

B12 Activate the trigger of the spray handle and let the water run until all air has escaped from

the water hose.

B13 Turn on the machine, turning the start/stop switch to position "I".

B14 Activate the trigger of the spray handle. When releasing the trigger of the spray handle,

the machine automatically stops. The machine will start again when you reactivate the

trigger of the spray handle.

4.5 Pressure regulation on the TORNADO® PR- nozzle

B15 The pressure can be regulated on the TORNADO

PR nozzle.

4.6 Stationary use

B16 If mounting a special wall hook (not standard), the pressure washer can be used as a

stationary solution meaning that it can be operated while hanging on the wall.

Only mount the wall hook on a sturdy wall. Adjust the length of the screws and size of

rawlplugs to the type of wall.

B17 On the wall hook garden/rim brush (a) foam sprayer (b), Click & Clean brush (c) and Click

& Clean nozzles (d) can be stored.

IMPORTANT!

The bearing capacity of the wall hook is max. 30 kg.



13Original Instructions

5 Fields of application and working methods

5.1 General

Efﬁ cient high presure cleaning is achieved by following a few guidelines, combined with your

own personal experience of speciﬁ c cleaning tasks. Accessories and detergents, when correct-

ly chosen, can increase the efﬁ ciency of your pressure washer. Here is some basic information

about cleaning.

5.1.1 Detergent and foam

Foam or detergent should be applied onto dry surfaces so that the chemical product is in direct

contact with the dirt. Detergents are applied from bottom to top, for example on a car body-

work, in order to avoid "super clean" areas, where the detergent collects in higher concentrati-

on and streams downwards. Let the detergent work for several minutes before rinsing but never

let it dry on the surface being cleaned. Note: It is important that the detergents do not dry up.

Otherwise the surface that has to be cleaned can be da maged.

5.1.2 Mechanical effect

In order to break down tough layers of dirt, additional mechanical effect may be required. Spe-

cial wash brushes offer this supplementary effect that cuts through dirt (especially by car wash-

ing).

Original Instructions

5.2 Typical ﬁ elds of application

Below you will ﬁ nd a description of a lot of cleaning tasks which can be solved by a pressure washer from

Gerni in association with accessories and detergents.

Task Accessories ‘Click

& Clean’

Cleaning method

Car

Car nozzle,

auto brush,

underchassis

nozzle,

Foam sprayer,

Car Combi Cleaner

1. Apply Car Combi Cleaner with the foam sprayer. Always

start from the bottom and work upwards. Let Car Combi

Cleaner act for at least 5 min.

2. Wash the car with the car nozzle, which has been optimized for

quick and gentle cleaning of enamelled surfaces (the jet is wider

and not so sharp). Start at the front of the car and work back-

wards to avoid water from penetrating by the door mouldings.

3. Use the brush for removal of trafﬁ c ﬁ lm which is not removed by the

nozzle. If the car is very dirty, apply Car Combi Clean er again.

4. Attach the undercarriage nozzle and clean undercarriage and

wheel arches.

5. Remove water from the surface of the car with the scraper

on the car brush. Make sure that all grains of sand etc. have

been removed before using the scraper. Wipe with a wash lea-

ther where the scraper cannot reach.

Rims, alumi-

nium

Rim brush,

auto nozzle,

atomizer,

Alu Cleaner

Apply Alu Cleaner with an automizer. Let it act for approx.

5 min. and wash with the rim brush. For steel rims, use Car Com-

bi Cleaner. Use the foam sprayer and wash with rim brush.

Be careful! The high pressure jet may damage the tyres.

Flagstones,

concrete

ﬂ oors and

other hard

surfaces

Powerspeed

nozzle,

Stone & Wood

Cleaner,

Patio Cleaner

Wash towards outlets or the like. On surfaces with foulings you

may start by applying Stone & Wood Cleaner with

the foam sprayer. Wash before the soap dries. Another

more effective and quicker method is to use the Patio

Cleaner. Thus you will also avoid splashes.

Garden furni-

ture, wood

Wood Cleaner

Garden brush

Apply Wood Cleaner and wash before the soap dries.

NOTE: Use the garden brush to clean off the dirt.

Brickwork,

Wood work

Powerspeed

nozzle,

Stone & Wood

Cleaner,

Patio Cleaner

Same method as for ﬂ agstones, but be careful - bad joints and

wood may be damaged by high pressure. You may choose only

to use the Tornado

nozzle. Adjust the distance (pressure) to

the quality of the joints and the wood. Patio Cleaner can also be

used on vertical surfaces.

Gutter

Underchassis spray

lance

Wash the gutter with the nozzle. Always wash towards

downpipes. Beware not to spray under the rooﬁ ng.

Cleaning of

drain pipes,

outlets, down

pipes etc.

Tube cleaner Push the tube cleaner approx. ½ m (to mark) into a tube or drain

and activate the trigger of the spray handle. The nozzle opening

turning backwards will pull the cleaner through the tube. The

nozzle will break down the „plug“ and ﬂ ush the dirt backwards.

Rust, paint

Water/sandblasting

equipment

Mount the water/sand blasting equipment and rust and paint

is efﬁ ciently and quickly removed. Beware not to damage the

surface to be sandblasted.

Greenhouse

Tornado

PR nozzle

brush, Stone &

Wood Cleaner

Wash with high pressure and maybe a brush. You may use Stone

& Wood Cleaner to remove foulings.

Garden tools,

lawn mover

Tornado

nozzle, Power-

speed

nozzle,

multiangle adaptor,

Metal Cleaner

Rinse the worst dirt off with the nozzle. Apply Metal Cleaner with

the foam sprayer and let it act for approx. 5 min. Wash with the

nozzle. You may use the multiangle adaptor for hard to get at

areas to avoid splashing.

15Original Instructions

6 After using the pressure washer

See the pictorial quick reference guide – storing the high pressure washer.

The high pressure washer should be stored in a frost free room! Should the machine by a mis-

take be frozen, it will be necessary to check it for damages.

6.1 Stopping the high pressure washer

C1 Shut off the water supply and activate the trigger of the spray handle and let the machine

run until no more water runs out of the nozzle. This will wash out water hose, high pres-

sure hose, spray lance and nozzles.

C2 Stop the machine, turning the start/stop switch to position "0".

C3 Unplug the machine from the power supply socket.

IMPORTANT!

To avoid accidents, the electric cable and the high pressure hose should always be wound up

carefully.

C4 Wind up the electric cable on the dedicated cable hook (18). The upper hook can be

turned to release the electric cable. The upper hook has a built-in clip for good holding of

the electrical cable.

C5 The high pressure washer comes in two models: A) with hook for storage of high pres-

sure hose (15) - B) with a hose reel (12).

C6 Rinse the spray lance, nozzles and the foam sprayer after use.

C7 Place spray handle (f), lance (a), nozzles (b), foam sprayer (c) in the holders on the high

pressure washer. The nozzle cleaning tool (d) and a Click & Clean brush (e) can also be

stored on the product.

7 Maintenance

See the pictorial quick reference guide - maintenance.

To ensure a long and problem free working life of the high pressure washer, please take the

following advices:

• Wash out water hose, high pressure hose, spray lance and accessory before mounting

• Clean the connectors of dust and sand

• Rinse the detergent bottle and the detergent nozzle

• Clean the nozzle

• Keep the water inlet ﬁ lter clean and unclogged

Cleaning of the water inlet ﬁ lter

D1 Clean the water inlet ﬁ lter regularly once a month or more frequently according to use.

Carefully loosen the ﬁ lter with a screwdriver and clean it. Check that it is intact before remount-

ing it.

Cleaning of nozzle

A clogging up in the nozzle causes a pump pressure which is too high, why cleaning is re-

quired immediately.

IMPORTANT!

The nozzle cleaning tool (11) should only be used when the nozzle is detached and the ma-

chine is stopped!

D2 Stop the machine and disconnect the nozzle. Clean the nozzle.



Original Instructions

D3 Flush the nozzle backwards with water.

Cleaning of machine vents

D4 The machine should be kept clean so as to let cooling air pass freely through the

machine vents.

Greasing of O-rings

D5 To ensure an easy connection and that O-rings do not dry up the couplings should

be greased regularly.

In case problems other than the above occur, please phone 1300 733 171 or check our website

www.gerni.com.au for your nearest service agent.

8 Troubleshooting

To avoid unnecessary disappointments, you should check the following before contacting the Gerni ser-

vice organization.

Symptom Cause Recommended action

Machine refuses to

start

Machine not plugged in

Defective socket

Fuse has blown

Defective extension cable

Plug in machine

Try another socket.

Replace fuse. Switch off other machines.

Try without the extension cable.

Fluctuating pressure

Pump sucking air

Valves dirty, worn out or stuck

Pump seals worn out

Check that hoses and connections are air-

tight.

Clean and replace or refer to local Gerni-

distributor.

Clean and replace or refer to local Gerni-

distributor.

Machine stops

Fuse has blown

Incorrect mains voltage

Thermal sensor activated

Nozzle partially blocked

Replace fuse. Switch off other machines.

Check that the mains voltage corresponds

to speciﬁ cation on the model tag.

Leave the washer for 5 minutes to cool

down.

Clean the nozzle (see section 7)

Fuse blows

Fuse too small Change to an installation higher than the

amp. consumption of the machine.

You may try without the extension cable.

Machine pulsating

Air in inlet hose/pump

Inadequate supply of mains

water

Nozzle partially blocked

Water ﬁ lter blocked

Hose kinked

Allow machine to run with open trigger until

regular working pressure resumes.

Check that the water supply corresponds to

speciﬁ cations required (see model tag)

NB! Avoid using long, thin hoses (min. 1/2")

Clean the nozzle (see section 7)

Clean the ﬁ lter (see section 7)

Straighten out hose.

Machine often starts

and stops by itself

Pump/spray handle is leaking Contact your nearest Gerni Service Centre.

Machine starts, but no

water comes out

Pump/hoses or accessory

frozen

No water supply

Water ﬁ lter blocked

Nozzle blocked

Wait for pump/hoses or accessory to thaw.

Connect inlet water.

Clean the ﬁ lter (see section 7)

Clean the nozzle (see section 7)

17Original Instructions

9 Accessories and detergents

Only use original accessories and detergents. For further information, see www.Gerni.com.

10 Warranty Conditions

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are

entitled to a replacement or refund for a major failure and for compensation for any other reasonably fore-

seeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be

of acceptable quality and the failure does not amount to a major failure.

Gerni high-pressure washers for domestic use are warranted for 2 years (complete machine) and the motor

pump unit is warranted for a total of 5 years from the date of purchase by:

AUSTRALIA:

Nilﬁ sk Pty LTd

Unit 1/13 Bessemer Street

Blacktown NSW 2148

Phone: 1300 556 710

E-mail: Warranty.au@nilﬁ sk.com

NEW ZEALAND:

Accent Tools Ltd

232 Bush Rd

Albany

Auckland 0632

Phone: 09 968 2610

E-mail: [email protected].nz

Equipment defects covered by this warranty will be repaired or replaced by one of the service centres of the

Gerni organisation. Find your local service agent here: http://www.gerni.com.au/.

If your high pressure washer or ac ces so ries are handed in for repair, it must be followed by a description/

spe ci ﬁ ca ti on of the fault, and the original purchase receipt, or a copy, must be enclosed.

Packing and postage/carriage is not covered by the warranty.

The bene ﬁ ts under this warranty are in addition to your national law of sale.

Guarantee repairs are being made on the following con dit ions:

• that defects are attributable to ﬂ aws or defects in materials or workmanship. (wear and tear

as well as misuse are not covered by the gu a ran tee).

• that the directions of this instruction manual have been thoroughly observed.

• that repair has not been carried out or attempted by other than Gerni-trained service staff.

• that only original accessories have been applied.

• that the product has not been exposed to abuse such as knocks, bumps or frost.

• that only water without any impurities has been used.

• that the high pressure washer has not been used for rental nor used com mer cial ly in any

other way.

Repairs under this guarantee include replacement of defective parts, exclusive of packing and postage/car-

riage. Besides, we refer to your national law of sale.

The machine should be forwarded to one of the service centres of the Gerni organisation with description/

spe ci ﬁ ca ti on of the fault.

Repairs not covered by the guarantee conditions will be invoiced. (I.e. malfunctions due to Causes men -

ti o ned in section Troubleshooting Chart of the instruction manual).

Please phone 1300 733 171 (Australia) or 09 9682610 (NZ) for service or warranty assistance only

after checking possible causes in the trouble shooting chart on page 16.

Original Instructions

11 Main technical Data

Type

Super

130.3

Super

135.3

Super

140.3

Super

145.3

Electric specifications

Rated voltage V 230-240 230-240 230-240 230-240

Rated frequency Hz 50 50 50 50

Rated power consumption kW 2.0 2.0 2.1 2.1

Current A 9.0 9.0 9.5 10

Protection class

Class I/

Class II

Class II Class II Class II Class II

Protection degree IP xx IPX5 IPX5 IPX5 IPX5

Hydraulic specifications

Rated pressure MPa/bar 12.5/125 12.5/125 13.5/135 14.0/140

Max. pressure MPa/bar 13.0/130 13.5/135 14.0/140 14.5/145

Rated water flow l/min/l/h 7.5/450 7.5/450 7.0/420 6.6/400

Max. water flow l/min/l/h 8.3/500 8.3/500 8.3/500 8.3/500

Max. water inlet pressure Mpa/bar 1/10 1/10 1/10

0 1/10

Max. water inlet temperature °C 60 60 60 60

Max. water inlet temp. suction mode °C 20 20 20 20

Weight kg 17.8 18.6 18.6 19.8

Hand-arm vibration according to ISO 5349-

Standard nozzle

m/s

< 2.5 ±1 < 2.5 ±1 < 2.5 ±1 < 2.5 ±1

Machines without hose reel:

Sound pressure level L

in accordance with

ISO 3744

Guaranteed sound power level L

WA in

accordance with 2000/14/EC

dB(A)

66.8 ±2

Machines with hose reel:

Sound pressure level L

in accordance with

ISO 3744

Guaranteed sound power level L

WA in

accordance with 2000/14/EC

dB(A) -

71.8 ±2

We reserve the right to make alterations.

19Original Instructions

12 Declaration of Conformity

We,

Nilﬁ sk A/S

Kornmarksvej 1

DK-2605 Broendby

DENMARK,

hereby solely declare that the products:

Product Description Type

HPW - Consumer 230-240 V 1~, 50 Hz – IP X5 Gerni Super 130.3, 135.3, 140.3, 145.3

and accessory variants of above-mentioned

types

are in compliance with the following standards:

Id and Version Title

EN 60335-1:2012+A11:2014 Household and similar electrical appliances - Safety - Part 1: General

requirements

EN 60335-2-79:2012 Household and similar electrical appliances - Safety - Part 2-79:

Particular requirements for high pressure cleaners and steam

cleaners

EN 55014-1:2006+A1:2009

+A2:2011

EMC - Requirements for household appliances, electric tools and simi-

lar apparatus - Part 1: Emission

EN 55014-2:1997+A1:2001

+A2:2008

EMC - Requirements for household appliances, electric tools and simi-

lar apparatus - Part 2: Immunity - Product family standard

EN 61000-3-11:2000 Electromagnetic compatibility (EMC) - Part 3-11: Limits - Limitation of

voltage changes, voltage ﬂ uctuations and ﬂ icker in public low-voltage

supply systems, for equipment with rated current ≤ 75 A per phase and

subject to conditional connection

EN 50581:2012 Technical documentation for the assessment of electrical and electronic

products with respect to restriction of hazardous substances

Following the provisions of:

Machinery Directive 2006/42/EC

EMC Directive 2004/108/EC

→ April 20, 2016 → 2014/30/EC

RoHS Directive 2011/65/EC

Noise Emission Directive 2000/14/EC – Conformity assessment procedure according to Annex V.

Compliance to harmonic current emissions is documented in the TCF

Super 130.3: Measured noise level [dB] 67 dB; Guaranteed noise level [dB] 82 dB

Super 135.3, Super 140.3, Super 145.3: Measured noise level [dB] 72 dB; Guaranteed noise level [dB] 86 dB

Hadsund 2015-12-02 Anton Sørensen

Senior Vice President – Global Operations

R&D – Vacuum Cleaners and High Pressure Washers

Place Date Name, Title Signature

Page is loading ...

Gerni Super 130.3 User manual

Brand: Gerni

Model: Super 130.3

Category: High-pressure cleaners

Type: User manual

This manual is also suitable for

Download PDF

report

Gerni Super 130.3 User manual

This manual is also suitable for

Gerni Super 130.3 User manual

Related papers

Other documents