Panasonic SCHTB885EG Operating instructions

Brand: Panasonic

Model: SCHTB885EG

Type: Operating instructions

2015/03/18

EG EB

RQT0A01-B

Operating Instructions

Home Theater Audio System

Model No. SC-HTB885

Thank you for purchasing this product.

Please read these instructions carefully before using this product,

and save this manual for future use.

Model number suffix “EB” denotes UK model.

Included Installation Instructions

The installation work should be done by a qualified installation specialist. (> 13 to 18)

Before commencing work, carefully read these installation instructions and the operating instructions

to ensure that installation is performed correctly.

(Please keep these instructions. You may need them when maintaining or moving this system.)

SC-HTB885EGEB_RQT0A01-B.book 1 ページ２０１５年１月２９日　木曜日　午後３時４５分

2015/03/18

EG EB

RQT0A01-B

Operating Instructions

Home Theater Audio System

Model No. SC-HTB885

Thank you for purchasing this product.

Please read these instructions carefully before using this product,

and save this manual for future use.

Model number suffix “EB” denotes UK model.

Included Installation Instructions

The installation work should be done by a qualified installation specialist. (> 13 to 18)

Before commencing work, carefully read these installation instructions and the operating instructions

to ensure that installation is performed correctly.

(Please keep these instructions. You may need them when maintaining or moving this system.)

SC-HTB885EGEB_RQT0A01-B.book 1 ページ２０１５年１月２９日　木曜日　午後３時４５分

2015/03/18

EG EB

RQT0A01-B

Operating Instructions

Home Theater Audio System

Model No. SC-HTB885

Thank you for purchasing this product.

Please read these instructions carefully before using this product,

and save this manual for future use.

Model number suffix “EB” denotes UK model.

Included Installation Instructions

The installation work should be done by a qualified installation specialist. (> 13 to 18)

Before commencing work, carefully read these installation instructions and the operating instructions

to ensure that installation is performed correctly.

(Please keep these instructions. You may need them when maintaining or moving this system.)

SC-HTB885EGEB_RQT0A01-B.book 1 ページ２０１５年１月２９日　木曜日　午後３時４５分

Upute za uporabu

Audiosustav za kućna kina

Model br. SC-HTB885

Zahvaljujemo na kupnji ovog proizvoda.

Prije uporabe proizvoda pažljivo pročitajte ove upute i spremite priručnik za buduću uporabu.

Uključene upute za postavljanje

Postavljanje bi trebao provoditi isključivo kvalicirani stručnjak za postavljanje uređaja.

( 13 do 18)

Prije pokretanja uređaja pažljivo pročitajte upute za postavljanje i upute za uporabu da biste bili

sigurni da je postavljanje ispravno izvedeno.

(Sačuvajte ove upute. Bit će vam potrebne kod održavanja ili premještanja jedinice.)

Model s oznakom "EB" odnosi se na model za Ujedinjeno Kraljevstvo.

RQT0A04

Mjere opreza

UPOZORENJE

Jedinica

● Da biste smanjili rizik od požara, strujnog

udara ili oštećenja proizvoda,

– jedinicu nemojte izlagati kiši, vlazi, kapanju

ili prskanju.

– na jedinicu nemojte stavljati posude s

tekućinom, kao što su vaze.

– koristite se samo preporučenim priborom.

– nemojte uklanjati poklopce.

– nemojte sami popravljati jedinicu.

Servisiranje povjerite stručnom osoblju.

● Da biste spriječili ozljede, uređaj mora biti

sigurno postavljen na zid u skladu s uputama

za postavljanje.

Kabel za napajanje izmjeničnom strujom

● Da biste smanjili rizik od požara, strujnog

udara ili oštećenja proizvoda,

– provjerite odgovara li napon mreže naponu

navedenom na ovom uređaju.

– umetnite utikač u strujnu utičnicu.

– kabel nemojte vući, savijati ili na njega

stavljati teške predmete.

– nemojte dirati utikač mokrim rukama.

– pri iskopčavanju utikač držite za kućište.

– nemojte se koristiti oštećenim utikačem ili

strujnom utičnicom.

● Utikač se upotrebljava za isključivanje jedinice.

Jedinicu postavite tako da se utikač odmah

može izvući iz utičnice.

Gumbasta baterija (litijska baterija)

● Rizik od požara, eksplozija i opeklina.

Bateriju nemojte rastavljati, zagrijavati je na

temperaturu iznad 60 °C ili paliti.

● Držite gumbastu bateriju izvan dohvata djece.

Gumbastu bateriju nikada nemojte stavljati u

usta. Ako je progutate, obratite se liječniku.

Mali predmet

● Držite vijke izvan dohvata djece da ih ne bi

progutala.

● Ljepljivu traku čuvajte izvan dohvata djece da

je ne bi progutala.

● Čuvajte gumbastu bateriju izvan dohvata djece

da je ne bi progutala.

OPREZ

Jedinica

● Na jedinicu nemojte stavljati izvore otvorenog

plamena, kao što su upaljene svijeće.

● Mobilni telefoni mogu izazvati radijske smetnje

za vrijeme korištenja jedinicom. Ako se pojave

takve smetnje, povećajte udaljenost između

ove jedinice i mobilnog telefona.

● Ova je jedinica namijenjena za uporabu u

umjerenim klimatskim uvjetima.

● Natpisna pločica nalazi se na donjoj strani

kućišta jedinice.

Postavljanje

● Jedinicu postavite na ravnu površinu.

● Da biste smanjili rizik od požara, strujnog

udara ili oštećenja proizvoda,

– jedinicu nemojte postaviti u ormar, ugrađeni

ormarić ili u drugi skučeni prostor. Jedinica

mora biti na dobro prozračenom mjestu.

– Ventilacijske otvore jedinice nemojte

zaklanjati novinama, stolnjacima, zavjesama

i sličnim predmetima.

– Jedinicu nemojte izlagati izravnoj sunčevoj

svjetlosti, visokim temperaturama, visokoj

vlazi i prekomjernim vibracijama.

Gumbasta baterija (litijska baterija)

● U slučaju nepravilne zamjene baterije postoji

opasnost od eksplozije. Baterije zamijenite

isključivo onom vrstom koju preporučuje

proizvođač.

● Umetnite tako da su polovi poravnati.

● Pogrešno rukovanje baterijama može prouzročiti

curenje elektrolita, što može uzrokovati požar.

– Izvadite baterije ako daljinski upravljač ne

namjeravate upotrebljavati dulje vrijeme.

Spremite ih na hladno, tamno mjesto.

– Nemojte zagrijavati ni izlagati otvorenom

plamenu.

– Ne ostavljajte baterije izložene izravnoj

sunčevoj svjetlosti dulje vrijeme u vozilu sa

zatvorenim vratima i prozorima.

● Ako želite odložiti baterije, obratite se

nadležnim lokalnim tijelima ili dobavljačima i

raspitajte se o pravilnom načinu odlaganja.

RQT0A04

Precautions

RQT0A04

Caution for AC Mains Lead

(For the AC mains plug of three pins)

For your safety, please read the following text

carefully.

This appliance is supplied with a moulded three

pin mains plug for your safety and convenience.

A 5-ampere fuse is fitted in this plug.

Should the fuse need to be replaced please

ensure that the replacement fuse has a rating of 5-

ampere and that it is approved by ASTA or BSI to

BS1362.

Check for the ASTA mark Ï

or the BSI mark Ì on

the body of the fuse.

If the plug contains a removable fuse cover you

must ensure that it is refitted when the fuse is

replaced.

If you lose the fuse cover the plug must not be

used until a replacement cover is obtained.

A replacement fuse cover can be purchased from

your local dealer.

Before use

Remove the connector cover.

How to replace the fuse

The location of the fuse differ according to the type

of AC mains plug (figures A and B). Confirm the

AC mains plug fitted and follow the instructions

below.

Illustrations may differ from actual AC mains plug.

1. Open the fuse cover with a screwdriver.

2. Replace the fuse and close or attach the fuse cover.

Figure A

Figure B

Fuse cover

Figure A Figure B

Fuse

(5 ampere)

Fuse

(5 ampere)

SC-HTB485-EGEBGN_RQT0A04-B.book 3 ページ２０１５年１月２２日　木曜日　午前１０時１５分

Precautions

RQT0A04

Caution for AC Mains Lead

(For the AC mains plug of three pins)

For your safety, please read the following text

carefully.

This appliance is supplied with a moulded three

pin mains plug for your safety and convenience.

A 5-ampere fuse is fitted in this plug.

Should the fuse need to be replaced please

ensure that the replacement fuse has a rating of 5-

ampere and that it is approved by ASTA or BSI to

BS1362.

Check for the ASTA mark Ï

or the BSI mark Ì on

the body of the fuse.

If the plug contains a removable fuse cover you

must ensure that it is refitted when the fuse is

replaced.

If you lose the fuse cover the plug must not be

used until a replacement cover is obtained.

A replacement fuse cover can be purchased from

your local dealer.

Before use

Remove the connector cover.

How to replace the fuse

The location of the fuse differ according to the type

of AC mains plug (figures A and B). Confirm the

AC mains plug fitted and follow the instructions

below.

Illustrations may differ from actual AC mains plug.

1. Open the fuse cover with a screwdriver.

2. Replace the fuse and close or attach the fuse cover.

Figure A

Figure B

Fuse cover

Figure A Figure B

Fuse

(5 ampere)

Fuse

(5 ampere)

SC-HTB485-EGEBGN_RQT0A04-B.book 3 ページ２０１５年１月２２日　木曜日　午前１０時１５分

(za 3-pinski utikač za napajanje

izmjeničnom strujom)

Radi osobne sigurnosti pažljivo pročitajte sljedeći

tekst.

Uređaj se isporučuje s izoliranim 3-pinskim

utikačem radi vaše sigurnosti i udobnosti. U

utikač je ugrađen osigurač od 5 ampera.

Ako je potrebno zamijeniti osigurač, upotrijebite

zamjenski osigurač od 5 ampera usklađen sa

standardom BS1362 i s oznakom odobrenja

ASTA ili BSI.

Potražite oznaku ASTA ili BSI na kućištu

osigurača.

Ako utikač ima poklopac osigurača koji se može

skinuti, nakon zamjene osigurača poklopac

obavezno vratite na mjesto.

Ako izgubite poklopac osigurača, utikač nije

dozvoljeno upotrebljavati sve dok se ne postavi

zamjenski poklopac.

Zamjenski poklopac osigurača možete kupiti kod

lokalnog dobavljača.

Prije uporabe

Skinite poklopac priključka.

Zamjena osigurača

Smještaj osigurača razlikuje se ovisno o vrsti

utikača za napajanje izmjeničnom strujom

(slike A i B). Provjerite je li utikač za napajanje

izmjeničnom strujom pričvršćen i slijedite upute u

nastavku.

Prikazi se mogu razlikovati od stvarnog utikača

za napajanje izmjeničnom strujom.

1. Pomoću odvijača otvorite poklopac osigurača.

2. Zamijenite osigurač i zatvorite ili pričvrstite

poklopac osigurača.

Mjere opreza

Slika A

Slika B

Poklopac

osigurača

Osigurač

(5 ampera)

Osigurač

(5 ampera)

Mjere opreza za kabel za napajanje

izmjeničnom strujom

RQT0A04

Sadržaj

Mjere opreza ......................................................................................................2

Mjere opreza za kabel za napajanje izmjeničnom strujom ............................3

Prije uporabe

Isporučene stavke .............................................................................................5

Sustav (SC-HTB885) .......................................................................................................... 5

Pribor .................................................................................................................................... 5

Opis kontrola na daljinskom upravljaču .........................................................6

Ovaj sustav (prednji dio) ...................................................................................................... 6

Ovaj sustav (stražnji dio) ..................................................................................................... 7

Daljinski upravljač ................................................................................................................. 8

Priprema

1. korak Spajanje ...............................................................................................9

Spajanje s TV-prijamnikom .................................................................................................. 9

Spajanje s uređajem kompatibilnim s HDMI ....................................................................... 10

Uporaba IR Blastera ............................................................................................................11

Spajanje kabela za napajanje izmjeničnom strujom .......................................................... 12

2. korak Postavljanje .......................................................................................13

Mjere opreza ....................................................................................................................... 13

Aktivni niskotonac .............................................................................................................. 13

Bežične smetnje ............................................................................................................... 13

Odabir načina postavljanja ................................................................................................. 14

Postavljanje glavne jedinice na policu ili stol ..................................................................... 15

Pričvršćivanje glavne jedinice na zid .................................................................................. 16

3. korak Bežične veze .....................................................................................19

Bežično spajanje aktivnog niskotonca ................................................................................ 19

Spajanje s Bluetoothom

.................................................................................................... 19

Kod daljinskog upravljača .............................................................................20

Funkcije

Korištenje ovim sustavom .............................................................................21

3D-zvuk ............................................................................................................22

Izbornik zvuka .................................................................................................22

Format zvuka ..................................................................................................................... 23

Izbornik postavljanja .......................................................................................24

Povezane radnje s TV-prijamnikom (VIERA Link "HDAVI Control

”) ........25

Reference

Rješavanje problema ......................................................................................26

Bluetooth

........................................................................................................29

Održavanje jedinice .........................................................................................29

Licencije ......................................................................................................... 29

Tehnički podaci ................................................................................................30

Getting started

Operations

Reference

Before use

Precautions

RQT0A01

Before use

Supplied items

Check the supplied accessories before using this system.



≥ Product numbers are correct as of January 2015. These may be subject to change.

≥ The supplied AC mains lead is for use with this system only.

Do not use it with other equipment. Also, do not use cords from other equipment with this system.

≥ The illustrations shown may differ from your unit.

≥ Operations in this operating instructions are described mainly with the remote control, but

you can perform the operations on the main unit if the controls are the same.

This system (SC-HTB885)

∏ 1 Main unit (speaker)

(SU-HTB885)

∏ 1 Active subwoofer

(SB-HWA880)

Accessories

∏ 1 Remote control (with a

battery)

(N2QAYC000109)

∏ 1 IR Blaster

(K2ZZ02C00007)

∏ 2 Wall mount brackets

(RMQ2281A, RMQ2281B)

∏ 2 AC mains leads

For the United Kingdom

and Ireland

(K2CT2YY00097)

For Continental Europe

(K2CQ2YY00119)

∏ 2 Screws

(XYN5+J14FJK)

SC-HTB885EGEB_RQT0A01-B.book 5 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

Operations

Reference

Before use

Precautions

RQT0A01

Before use

Supplied items

Check the supplied accessories before using this system.



≥ Product numbers are correct as of January 2015. These may be subject to change.

≥ The supplied AC mains lead is for use with this system only.

Do not use it with other equipment. Also, do not use cords from other equipment with this system.

≥ The illustrations shown may differ from your unit.

≥ Operations in this operating instructions are described mainly with the remote control, but

you can perform the operations on the main unit if the controls are the same.

This system (SC-HTB885)

∏ 1 Main unit (speaker)

(SU-HTB885)

∏ 1 Active subwoofer

(SB-HWA880)

Accessories

∏ 1 Remote control (with a

battery)

(N2QAYC000109)

∏ 1 IR Blaster

(K2ZZ02C00007)

∏ 2 Wall mount brackets

(RMQ2281A, RMQ2281B)

∏ 2 AC mains leads

For the United Kingdom

and Ireland

(K2CT2YY00097)

For Continental Europe

(K2CQ2YY00119)

∏ 2 Screws

(XYN5+J14FJK)

SC-HTB885EGEB_RQT0A01-B.book 5 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

● Prikazane se slike mogu razlikovati od vaše jedinice.

● U ovim se uputama za uporabu opisuje način rukovanja pomoću daljinskog upravljača, ali

neki se postupci mogu izvoditi i tipkama na glavnoj jedinici ako su kontrole jednake.

Isporučene stavke

Ovaj sustav (SC-HTB885)

Pribor

Provjerite isporučeni pribor prije korištenja sustavom.

● Brojevi dijelova važeći su od siječnja 2015. Podložni su promjenama.

● Isporučeni kabel za napajanje izmjeničnom strujom može se koristiti samo s ovim sustavom.

Nemojte ga upotrebljavati s drugom opremom. Također, s ovim sustavom nemojte upotrebljavati kabele drugih

uređaja.

1 glavna jedinica (zvučnik)

(SU-HTB885)

1 aktivni niskotonac

(SB-HWA880)

1 daljinski upravljač

(s baterijom)

(N2QAYC000109)

Za Ujedinjeno

Kraljevstvo i Irsku

(K2CT2YY00097)

Za područje

kontinentalne Europe

(K2CQ2YY00119)

1 IR blaster

(K2ZZ02C00007)

2 vijka

(XYN5+J14FJK)

2 kabela za napajanje izmjeničnom strujom

Mjere oprezaPrije uporabePripremaFunkcijeReference

2 držača za postavljanje na zid

(RMQ2281A, RMQ2281B)

RQT0A01

Control reference guide

1 NFC touch area (> 20)

2 Standby/on switch (Í/I)

Touch to switch the unit from on to standby

mode or vice versa. In standby mode, the unit

is still consuming a small amount of power.

3 Adjust the volume of this system (> 21)

4 Select the input source (> 21)

“TV” --# “BD/DVD” --# “AUX”

^-----“BLUETOOTH”(------}

5 Select the Bluetooth

device as the source

(> 21)

6 Remote control signal sensor for table top

layout (> 8)

7 Remote control signal sensor for wall

mounting layout (> 8)

8 Display

9 WIRELESS LINK indicator (> 19)

These switches work just by touching the marks. Each time you touch the switch, there will be a beep sound.

This system (Front)

3 4 52

Main unit

Active subwoofer

SC-HTB885EGEB_RQT0A01-B.book 6 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

1 NFC-područje osjetljivo na dodir ( 20)

2 Prekidač za stanje čekanja / uključivanje ( /I)

Dodirnite da biste uključenu jedinicu prebacili

u stanje čekanja i obrnuto. U stanju čekanja

jedinica i dalje troši malu količinu energije.

3 Podešavanje glasnoće ovog sustava ( 21)

4 Odabir ulaznog izvora ( 21)

“TV” → “BD/DVD” → “AUX“

“BLUETOOTH”

5 Odaberite Bluetooth

uređaj kao izvor ( 21)

6 Senzor signala daljinskog upravljača za

postavljanje na stol ( 8)

7 Senzor signala daljinskog upravljača za

postavljanje na zid ( 8)

8 Prikaz

9 Pokazatelj WIRELESS LINK ( 19)

* Ovi prekidači rade jednostavnim dodirom oznaka. Svaki put kad dodirnete prekidač, čut ćete zvučni

signal.

Opis kontrola na daljinskom upravljaču

Sustav (Prednji dio)

Glavna jedinica

Aktivni niskotonac

Before use

RQT0A01

1 HDMI AV OUT (TV (ARC)) terminal (ARC

compatible) (> 9, 10)

2 HDMI AV IN (AUX (HDMI 2)) terminal (> 10)

3 HDMI AV IN (BD/DVD (HDMI 1)) terminal

(

10)

4 USB port (for service use only)

5 OPTICAL DIGITAL AUDIO IN (TV) terminal

(> 10)

6 Ir SYSTEM terminal (> 11, 12)

7 AC IN terminal (> 12)

8 Active subwoofer on/off button (> 19)

§ The I/D SET button is only used when the main unit is not paired with the active subwoofer. (> 28)

This system (Rear)

Main unit

Active subwoofer

Left side Right side

SC-HTB885EGEB_RQT0A01-B.book 7 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

Sustav (Stražnji dio)

1 HDMI AV izlazni (TV (ARC)) priključak

(kompatibilan s funkcijom ARC) ( 9, 10)

2 HDMI AV ulazni (AUX (HDMI 2)) priključak

( 10)

3 HDMI AV ulazni (BD/DVD (HDMI 1)) priključak

( 10)

4 USB-ulaz (samo za servisnu uporabu)

5 Ulazni optički digitalni audiopriključak (TV)

( 10)

6 Priključak Ir sustava ( 11, 12)

7 Ulazni priključak izmjenične struje (AC IN)

( 12)

8 Gumb za uklj./isklj. aktivnog niskotonca ( 19)

* Gumb I/D SET koristi se samo kada glavna jedinica nije uparena s aktivnim niskotoncem. ( 28)

Prije uporabe

Aktivni niskotonac

Lijeva strana Desna strana

Glavna jedinica

RQT0A01

1 Turn the main unit on or off (> 21)

2 Select the input source (> 21)

“TV” --# “BD/DVD” --# “AUX”

^-----“BLUETOOTH”(------}

3 Select the setup menu (> 24)

4 Select the sound menu (> 22)

5 Select the Bluetooth

device as the source

(> 21)

6 Adjust the volume of this system (> 21)

7 Mute the sound (> 21)

8 Select and confirm the option

∫ About remote control signal sensor

The remote control signal sensor is located on the main unit.

≥Use the remote control within the correct operation range.

Distance: Within approx. 7 m directly in front

Angle: Approx. 30

left and right

B Remote control signal sensor for table top layout

C Remote control signal sensor for wall mounting layout

Remote control

SOUND

MUSIC

INPUT

SETUP





∫ Before using for the first time

Remove the insulation sheet A.

∫ To replace a button-type battery

Battery type: CR2025 (Lithium battery)

≥ Set the button-type battery with its (i) mark

facing upward.









For table top layout

For wall mounting layout

SC-HTB885EGEB_RQT0A01-B.book 8 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A01

1 Turn the main unit on or off (> 21)

2 Select the input source (> 21)

“TV” --# “BD/DVD” --# “AUX”

^-----“BLUETOOTH”(------}

3 Select the setup menu (> 24)

4 Select the sound menu (> 22)

5 Select the Bluetooth

device as the source

(> 21)

6 Adjust the volume of this system (> 21)

7 Mute the sound (> 21)

8 Select and confirm the option

∫ About remote control signal sensor

The remote control signal sensor is located on the main unit.

≥Use the remote control within the correct operation range.

Distance: Within approx. 7 m directly in front

Angle: Approx. 30

left and right

B Remote control signal sensor for table top layout

C Remote control signal sensor for wall mounting layout

Remote control

SOUND

MUSIC

INPUT

SETUP





∫ Before using for the first time

Remove the insulation sheet A.

∫ To replace a button-type battery

Battery type: CR2025 (Lithium battery)

≥ Set the button-type battery with its (i) mark

facing upward.









For table top layout

For wall mounting layout

SC-HTB885EGEB_RQT0A01-B.book 8 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

1 Uključivanje/isključivanje glavne jedinice ( 21)

2 Odabir ulaznog izvora ( 21)

“TV” → “BD/DVD” → “AUX“

“BLUETOOTH”

3 Odaberite izbornik postavljanja ( 24)

4 Odaberite izbornik zvuka ( 22)

5 Odaberite Bluetooth

uređaj kao izvor ( 21)

6 Podešavanje glasnoće ovog sustava ( 21)

7 Isključivanje zvuka ( 21)

8 Odaberite i potvrdite opciju

■ Prije prve uporabe

Uklonite traku za izolaciju A.

■ Zamjena gumbaste baterije

Vrsta baterije: CR2025 (litijska baterija)

● Umetnite gumbastu bateriju s oznakom (+)

okrenutom prema gore.

Daljinski upravljač

■ Senzor signala daljinskog upravljača

Senzor signala daljinskog upravljača nalazi se na glavnoj jedinici.

● Daljinski se upravljač mora upotrebljavati u ispravnom dometu.

Udaljenost: Unutar otprilike 7m direktno ispred

Kut: približno 30º ulijevo i udesno

Kod postavljanja na stol Kod postavljanja na zid

A Senzor signala daljinskog upravljača za postavljanje na stol

B Senzor signala daljinskog upravljača za postavljanje na zid

RQT0A01

1 Turn the main unit on or off (> 21)

2 Select the input source (> 21)

“TV” --# “BD/DVD” --# “AUX”

^-----“BLUETOOTH”(------}

3 Select the setup menu (> 24)

4 Select the sound menu (> 22)

5 Select the Bluetooth

device as the source

(> 21)

6 Adjust the volume of this system (> 21)

7 Mute the sound (> 21)

8 Select and confirm the option

∫ About remote control signal sensor

The remote control signal sensor is located on the main unit.

≥Use the remote control within the correct operation range.

Distance: Within approx. 7 m directly in front

Angle: Approx. 30

left and right

B Remote control signal sensor for table top layout

C Remote control signal sensor for wall mounting layout

Remote control

SOUND

MUSIC

INPUT

SETUP





∫ Before using for the first time

Remove the insulation sheet A.

∫ To replace a button-type battery

Battery type: CR2025 (Lithium battery)

≥ Set the button-type battery with its (i) mark

facing upward.









For table top layout

For wall mounting layout

SC-HTB885EGEB_RQT0A01-B.book 8 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A01

1 Turn the main unit on or off (> 21)

2 Select the input source (> 21)

“TV” --# “BD/DVD” --# “AUX”

^-----“BLUETOOTH”(------}

3 Select the setup menu (> 24)

4 Select the sound menu (> 22)

5 Select the Bluetooth

device as the source

(> 21)

6 Adjust the volume of this system (> 21)

7 Mute the sound (> 21)

8 Select and confirm the option

∫ About remote control signal sensor

The remote control signal sensor is located on the main unit.

≥Use the remote control within the correct operation range.

Distance: Within approx. 7 m directly in front

Angle: Approx. 30

left and right

B Remote control signal sensor for table top layout

C Remote control signal sensor for wall mounting layout

Remote control

SOUND

MUSIC

INPUT

SETUP





∫ Before using for the first time

Remove the insulation sheet A.

∫ To replace a button-type battery

Battery type: CR2025 (Lithium battery)

≥ Set the button-type battery with its (i) mark

facing upward.









For table top layout

For wall mounting layout

SC-HTB885EGEB_RQT0A01-B.book 8 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

Before use

RQT0A04

Getting started

Step 1 Connections

≥Turn off all equipment before connection and read the appropriate operating instructions.

Do not connect the AC mains lead until all other connections are completed.

∫ HDMI (High-Definition Multimedia Interface)

≥ The HDMI connection supports VIERA Link “HDAVI Control” (> 25) when used with a compatible Panasonic TV.

≥ Use the ARC compatible High Speed HDMI Cables. Non-HDMI-compliant cables cannot be utilised.

≥ It is recommended that you use Panasonic’s HDMI cable.

∫ IR (Infrared) Blaster

≥ Do not use the IR Blaster if the TV’s remote control sensor is not blocked by the main unit. (> 14)

Verify if the TV’s HDMI terminal is labelled “HDMI (ARC)”.

∫ What is ARC?

ARC is an abbreviation of Audio Return Channel, also known as HDMI ARC. It refers to one of the HDMI functions. When you

connect the main unit to the terminal labelled “HDMI (ARC)” on the TV, the optical digital audio cable that is usually required in

order to listen to sound from a TV is no longer required, and TV pictures and sound can be enjoyed with a single HDMI cable.

Make the connection.

A HDMI cable

Connection with the TV

Connection differs depending on the label printed next to the HDMI terminal.

Labelled “HDMI (ARC)”: Connection [A]

Not Labelled “HDMI (ARC)”: Connection [B]

[A] Labelled “HDMI (ARC)”

HDMI IN (ARC)

AV OUT

TV(ARC)

Be sure to connect to

the TV’s ARC

compatible terminal.

(Refer to the operating

instructions for the TV.)

SC-HTB485-EGEBGN_RQT0A04-B.book 9 ページ２０１５年１月２２日　木曜日　午前１０時１５分

Getting started

Before use

RQT0A04

Getting started

Step 1 Connections

≥Turn off all equipment before connection and read the appropriate operating instructions.

Do not connect the AC mains lead until all other connections are completed.

∫ HDMI (High-Definition Multimedia Interface)

≥ The HDMI connection supports VIERA Link “HDAVI Control” (> 25) when used with a compatible Panasonic TV.

≥ Use the ARC compatible High Speed HDMI Cables. Non-HDMI-compliant cables cannot be utilised.

≥ It is recommended that you use Panasonic’s HDMI cable.

∫ IR (Infrared) Blaster

≥ Do not use the IR Blaster if the TV’s remote control sensor is not blocked by the main unit. (> 14)

Verify if the TV’s HDMI terminal is labelled “HDMI (ARC)”.

∫ What is ARC?

ARC is an abbreviation of Audio Return Channel, also known as HDMI ARC. It refers to one of the HDMI functions. When you

connect the main unit to the terminal labelled “HDMI (ARC)” on the TV, the optical digital audio cable that is usually required in

order to listen to sound from a TV is no longer required, and TV pictures and sound can be enjoyed with a single HDMI cable.

Make the connection.

A HDMI cable

Connection with the TV

Connection differs depending on the label printed next to the HDMI terminal.

Labelled “HDMI (ARC)”: Connection [A]

Not Labelled “HDMI (ARC)”: Connection [B]

[A] Labelled “HDMI (ARC)”

HDMI IN (ARC)

AV OUT

TV(ARC)

Be sure to connect to

the TV’s ARC

compatible terminal.

(Refer to the operating

instructions for the TV.)

SC-HTB485-EGEBGN_RQT0A04-B.book 9 ページ２０１５年１月２２日　木曜日　午前１０時１５分

Getting started

Before use

RQT0A01

Getting started

Step 1 Connections

≥Turn off all equipment before connection and read the appropriate operating instructions.

Do not connect the AC mains lead until all other connections are completed.

∫ HDMI (High-Definition Multimedia Interface)

≥ The HDMI connection supports VIERA Link “HDAVI Control” (> 25) when used with a compatible Panasonic TV.

≥ Use the ARC compatible High Speed HDMI Cables. Non-HDMI-compliant cables cannot be utilised.

≥ It is recommended that you use Panasonic’s HDMI cable.

∫ IR (Infrared) Blaster

≥ Do not use the IR Blaster if the TV’s remote control sensor is not blocked by the main unit. (> 14)

≥ The supplied IR Blaster is only compatible with Panasonic TVs.

Verify if the TV’s HDMI terminal is labelled “HDMI (ARC)”.

∫ What is ARC?

ARC is an abbreviation of Audio Return Channel, also known as HDMI ARC. It refers to one of the HDMI functions. When you

connect the main unit to the terminal labelled “HDMI (ARC)” on the TV, the optical digital audio cable that is usually required in

order to listen to sound from a TV is no longer required, and TV pictures and sound can be enjoyed with a single HDMI cable.

Make the connection.

A HDMI cable

Connection with the TV

Connection differs depending on the label printed next to the HDMI terminal.

Labelled “HDMI (ARC)”: Connection [A]

Not Labelled “HDMI (ARC)”: Connection [B]

[A] Labelled “HDMI (ARC)”

HDMI IN (ARC)

Be sure to connect to

the TV’s ARC

compatible terminal.

(Refer to the

operating instructions

for the TV.)

SC-HTB885EGEB_RQT0A01-B.book 9 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

1. korak Povezivanje

● Prije spajanja isključite svu opremu te pročitajte odgovarajuće upute za uporabu.

Nemojte spajati kabel za napajanje izmjeničnom strujom dok ne provedete sva ostala spajanja.

■ HDMI (High-Denition Multimedia Interface)

● HDMI-povezivanje podržava VIERA Link “HDAVI Control” ( 25) kad se upotrebljava za spajanje s kompatibilnim

Panasonicovim TV-prijamnikom.

● Koristite se HDMI-kabelima velike brzine, kompatibilne s funkcijom ARC. Ne mogu se upotrebljavati kabeli koji nisu

kompatibilni s tehnologijom HDMI.

● Preporučuje se uporaba Panasonicovih HDMI-kabela.

■ IR (infracrveni) Blaster

● Nemojte upotrebljavati IR Blaster ako glavna jedinica ne blokira senzor daljinskog upravljača TV-prijamnika. ( 14)

● Isporučeni IR Blaster kompatibilan je samo s TV-prijamnicima tvrtke Panasonic.

Povezivanje s TV-prijamnikom

Provjerite je li HDMI-priključak TV-prijamnika označen kao “HDMI (ARC)”.

Spajanje se razlikuje ovisno o oznaci navedenoj kraj HDMI-priključka.

S oznakom “HDMI (ARC)”: Povezivanje A

Bez oznake “HDMI (ARC)”: Povezivanje B

■ Što je ARC?

ARC je kratica za Audio Return Channel (Povratni audiokanal), a poznat je i kao HDMI ARC. Riječ je o HDMI-funkciji. Kada

glavnu jedinicu spojite na priključak označen s “HDMI (ARC)” na TV-prijamniku, optički digitalni audiokabel koji je inače

potreban za slušanje zvuka na TV-prijamniku više nije potreban, a u slikama i zvuku na TV-prijamniku možete uživati s pomoću

HDMI-kabela.

Spojite.

A S oznakom “HDMI (ARC)”

Priprema Prije uporabe

Obavezno spojite na

priključak TV-prijamnika

kompatibilan s funkcijom

ARC. (Detalje potražite

u uputama za uporabu

TV-prijamnika.)

Izlazni AV-

priključak

TV (ARC)

Ulazni HDMI-

priključak (ARC)

A HDMI-kabel

RQT0A01

A HDMI cable

B Optical digital audio cable

≥ When you use the optical digital audio cable, insert

the tip correctly into the terminal.

You can direct the audio signal from the connected Blu-ray Disc player, DVD player, Set Top Box, etc. to

this system.

Preparation

≥Connect the main unit to the TV. (> 9)

A HDMI cable

[B] Not labelled “HDMI (ARC)”

HDMI IN

OPTICAL

OUT

Connection from an HDMI compatible device

HDMI OUT

e.g., Set top box

e.g., Blu-ray Disc player

SC-HTB885EGEB_RQT0A01-B.book 10 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A01

A HDMI cable

B Optical digital audio cable

≥ When you use the optical digital audio cable, insert

the tip correctly into the terminal.

You can direct the audio signal from the connected Blu-ray Disc player, DVD player, Set Top Box, etc. to

this system.

Preparation

≥Connect the main unit to the TV. (> 9)

A HDMI cable

[B] Not labelled “HDMI (ARC)”

HDMI IN

OPTICAL

OUT

Connection from an HDMI compatible device

HDMI OUT

e.g., Set top box

e.g., Blu-ray Disc player

SC-HTB885EGEB_RQT0A01-B.book 10 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

Spajanje s uređajem kompatibilnim s HDMI

Možete usmjeriti audiosignal spojenog Blu-ray čitača, DVD-čitača, digitalnog prijamnika itd. na ovaj

sustav.

Priprema

● Spojite glavnu jedinicu s TV-prijamnikom. ( 9)

A HDMI-kabel

B Bez oznake “HDMI (ARC)”

Ulazni HDMI-

priključak

Izlazni HDMI-

priključak

Izlazni HDMI-

priključak

npr. Blu-ray čitač

npr. digitalni prijamnik

Izlazni optički

priključak

A HDMI-kabel

B Optički digitalni audiokabel

● Kada koristite optički digitalni audiokabel,

ispravno umetnite vrh u priključak.

Ulazni optički

digitalni

audiopriključak

Ulazni AV-

priključak

AUX

(HDMI 2)

Ulazni AV-

priključak

BD/DVD

(HDMI 1)

Izlazni AV-

priključak

TV (ARC)

Getting started

RQT0A01



≥ Refer to the operating instructions of the connected HDMI compatible device for the necessary setting, to output the video and

audio signals.

With the IR Blaster connection, it is possible to send the IR signal received by this system’s remote

control signal sensor to the TV’s sensor.

Use the TV’s remote control within the operation range of this system’s remote control signal sensor.

≥For the operation range, refer to page 8.

Connect the jack plug to the main unit’s Ir SYSTEM terminal.

Place the infrared emitter in sight of the TV’s remote control signal

sensor.

≥ For the location of the TV’s remote control signal sensor, refer to the operating instructions for the TV.

Aim the TV’s remote control at this system’s remote control sensor and

operate the TV.

≥ For the location of this system’s remote control signal sensor, refer to page 8.

≥ Make sure to clean the surface, where the adhesive tape is to be attached.

≥ If you peel off the adhesive tape, the surface may become damaged and exposed adhesive may remain. Once you have

confirmed the TV is operating correctly, secure it by attaching the adhesive tape.

∫ HDMI standby pass-through

Even if the main unit is in standby mode, the audio and/or video signal from the device connected to the HDMI AV IN1 or

HDMI AV IN2 terminal will be sent to the TV connected to the HDMI AV OUT terminal (the sound will not be output from this

system). When devices are connected to all HDMI AV IN1 and HDMI AV IN2 terminals, audio and/or video signal of the

device whose input is lastly selected is output.

∫ 3D compatibility

Compatible with FULL HD 3D TV and Blu-ray Disc player.

≥ The main unit can pass-through the 3D video signal from a 3D compatible Blu-ray Disc player to a FULL HD 3D TV.

∫ 4K/60p compatibility

Compatible with 4K Ultra HD TV and Blu-ray Disc player.

≥ This system can pass-through the 4K content of a 4K compatible equipment to a 4K Ultra HD TV.

≥ When connecting to 4K compatible equipment and 4K Ultra HD TV, use High Speed HDMI cables which support 18 Gbps

bandwidth.

Using the IR Blaster

Ir SYSTEM

Infrared emitter

SC-HTB885EGEB_RQT0A01-B.book 11 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

RQT0A01



≥ Refer to the operating instructions of the connected HDMI compatible device for the necessary setting, to output the video and

audio signals.

With the IR Blaster connection, it is possible to send the IR signal received by this system’s remote

control signal sensor to the TV’s sensor.

Use the TV’s remote control within the operation range of this system’s remote control signal sensor.

≥For the operation range, refer to page 8.

Connect the jack plug to the main unit’s Ir SYSTEM terminal.

Place the infrared emitter in sight of the TV’s remote control signal

sensor.

≥ For the location of the TV’s remote control signal sensor, refer to the operating instructions for the TV.

Aim the TV’s remote control at this system’s remote control sensor and

operate the TV.

≥ For the location of this system’s remote control signal sensor, refer to page 8.

≥ Make sure to clean the surface, where the adhesive tape is to be attached.

≥ If you peel off the adhesive tape, the surface may become damaged and exposed adhesive may remain. Once you have

confirmed the TV is operating correctly, secure it by attaching the adhesive tape.

∫ HDMI standby pass-through

Even if the main unit is in standby mode, the audio and/or video signal from the device connected to the HDMI AV IN1 or

HDMI AV IN2 terminal will be sent to the TV connected to the HDMI AV OUT terminal (the sound will not be output from this

system). When devices are connected to all HDMI AV IN1 and HDMI AV IN2 terminals, audio and/or video signal of the

device whose input is lastly selected is output.

∫ 3D compatibility

Compatible with FULL HD 3D TV and Blu-ray Disc player.

≥ The main unit can pass-through the 3D video signal from a 3D compatible Blu-ray Disc player to a FULL HD 3D TV.

∫ 4K/60p compatibility

Compatible with 4K Ultra HD TV and Blu-ray Disc player.

≥ This system can pass-through the 4K content of a 4K compatible equipment to a 4K Ultra HD TV.

≥ When connecting to 4K compatible equipment and 4K Ultra HD TV, use High Speed HDMI cables which support 18 Gbps

bandwidth.

Using the IR Blaster

Ir SYSTEM

Infrared emitter

SC-HTB885EGEB_RQT0A01-B.book 11 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

RQT0A01



≥ Refer to the operating instructions of the connected HDMI compatible device for the necessary setting, to output the video and

audio signals.

With the IR Blaster connection, it is possible to send the IR signal received by this system’s remote

control signal sensor to the TV’s sensor.

Use the TV’s remote control within the operation range of this system’s remote control signal sensor.

≥For the operation range, refer to page 8.

Connect the jack plug to the main unit’s Ir SYSTEM terminal.

Place the infrared emitter in sight of the TV’s remote control signal

sensor.

≥ For the location of the TV’s remote control signal sensor, refer to the operating instructions for the TV.

Aim the TV’s remote control at this system’s remote control sensor and

operate the TV.

≥ For the location of this system’s remote control signal sensor, refer to page 8.

≥ Make sure to clean the surface, where the adhesive tape is to be attached.

≥ If you peel off the adhesive tape, the surface may become damaged and exposed adhesive may remain. Once you have

confirmed the TV is operating correctly, secure it by attaching the adhesive tape.

∫ HDMI standby pass-through

Even if the main unit is in standby mode, the audio and/or video signal from the device connected to the HDMI AV IN1 or

HDMI AV IN2 terminal will be sent to the TV connected to the HDMI AV OUT terminal (the sound will not be output from this

system). When devices are connected to all HDMI AV IN1 and HDMI AV IN2 terminals, audio and/or video signal of the

device whose input is lastly selected is output.

∫ 3D compatibility

Compatible with FULL HD 3D TV and Blu-ray Disc player.

≥ The main unit can pass-through the 3D video signal from a 3D compatible Blu-ray Disc player to a FULL HD 3D TV.

∫ 4K/60p compatibility

Compatible with 4K Ultra HD TV and Blu-ray Disc player.

≥ This system can pass-through the 4K content of a 4K compatible equipment to a 4K Ultra HD TV.

≥ When connecting to 4K compatible equipment and 4K Ultra HD TV, use High Speed HDMI cables which support 18 Gbps

bandwidth.

Using the IR Blaster

Ir SYSTEM

Infrared emitter

SC-HTB885EGEB_RQT0A01-B.book 11 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

RQT0A01



≥ Refer to the operating instructions of the connected HDMI compatible device for the necessary setting, to output the video and

audio signals.

With the IR Blaster connection, it is possible to send the IR signal received by this system’s remote

control signal sensor to the TV’s sensor.

Use the TV’s remote control within the operation range of this system’s remote control signal sensor.

≥For the operation range, refer to page 8.

Connect the jack plug to the main unit’s Ir SYSTEM terminal.

Place the infrared emitter in sight of the TV’s remote control signal

sensor.

≥ For the location of the TV’s remote control signal sensor, refer to the operating instructions for the TV.

Aim the TV’s remote control at this system’s remote control sensor and

operate the TV.

≥ For the location of this system’s remote control signal sensor, refer to page 8.

≥ Make sure to clean the surface, where the adhesive tape is to be attached.

≥ If you peel off the adhesive tape, the surface may become damaged and exposed adhesive may remain. Once you have

confirmed the TV is operating correctly, secure it by attaching the adhesive tape.

∫ HDMI standby pass-through

Even if the main unit is in standby mode, the audio and/or video signal from the device connected to the HDMI AV IN1 or

HDMI AV IN2 terminal will be sent to the TV connected to the HDMI AV OUT terminal (the sound will not be output from this

system). When devices are connected to all HDMI AV IN1 and HDMI AV IN2 terminals, audio and/or video signal of the

device whose input is lastly selected is output.

∫ 3D compatibility

Compatible with FULL HD 3D TV and Blu-ray Disc player.

≥ The main unit can pass-through the 3D video signal from a 3D compatible Blu-ray Disc player to a FULL HD 3D TV.

∫ 4K/60p compatibility

Compatible with 4K Ultra HD TV and Blu-ray Disc player.

≥ This system can pass-through the 4K content of a 4K compatible equipment to a 4K Ultra HD TV.

≥ When connecting to 4K compatible equipment and 4K Ultra HD TV, use High Speed HDMI cables which support 18 Gbps

bandwidth.

Using the IR Blaster

Ir SYSTEM

Infrared emitter

SC-HTB885EGEB_RQT0A01-B.book 11 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

Priprema

■ Prolaz kroz HDMI u stanju čekanja

Čak i ako je glavna jedinica u stanju čekanja, audiosignal i/ili videosignal iz uređaja spojenog s HDMI AV IN1 ili HDMI AV

IN2 priključkom slat će se TV-prijamniku spojenom s izlaznim HDMI AV-priključkom. (Zvuk neće dopirati iz ovog sustava.)

Kad su uređaji spojeni na sve HDMI AV IN1 i HDMI AV IN2 priključke, reproducirat će se audiosignal i/ili videosignal uređaja

čiji je ulaz posljednji odabran.

■ Kompatibilnost s tehnologijom 3D

Kompatibilan s TV-prijamnikom FULL HD 3D i Blu-Ray čitačem.

● Glavna jedinica može provoditi 3D-signal iz Blu-ray čitača kompatibilnog s tehnologijom 3D do TV-prijamnika FULL HD 3D.

■ 4K/60p kompatibilnost

Kompatibilan s 4K Ultra HD TV-prijamnikom i Blu-Ray čitačem.

● Ovaj sustav može propustiti 4K sadržaj 4K kompatibilne opreme na 4K Ultra HD TV-prijamnik.

● Kad spajate s 4K kompatibilnom opremom i 4K Ultra HD TV-prijamnikom, koristite se HDMI-kabelima velike brzine koji

podupiru propusnost od 18 Gbps.

● U uputama za uporabu spojenog uređaja kompatibilnog s HDMI potražite podatke o potrebnim postavkama da bi se

omogućilo odašiljanje audiosignala i videosignala.

Uporaba IR Blastera

Kada je IR Blaster spojen, moguće je slati infracrveni signal koji je primio senzor signala daljinskog

upravljača na senzor TV-prijamnika.

Upotrebljavajte daljinski upravljač TV-prijamnika unutar dometa senzora signala daljinskog

upravljača ovog sustava.

● Detalje o dometu potražite na 8. str.

Spojite utikač u priključak lr sustava glavne jedinice.

Postavite infracrveni odašiljač na vidljivoj udaljenosti od senzora

signala daljinskog upravljača TV-prijamnika.

● Detalje o položaju senzora signala daljinskog upravljača TV-prijamnika potražite u uputama za uporabu za TV-prijamnik.

Usmjerite daljinski upravljač TV-prijamnika u senzor daljinskog

upravljača ovog sustava i upravljajte TV-prijamnikom.

● Položaj senzora signala daljinskog upravljača ovog sustava potražite na 8. stranici.

● Očistite površinu na koju ćete zalijepiti ljepljivu traku.

● Ako odlijepite ljepljivu traku, površina se može oštetiti i može ostati izloženog ljepila. Nakon što potvrdite da TV-prijamnik

radi ispravno, učvrstite ga ljepljivom trakom.

Ir sustav

Infracrveni odašiljač

RQT0A01

∫ Placement example

On the rear of the main unit:

≥ Connect only after all other connections are completed.

A To a household mains socket

B AC mains lead (supplied)

≥

This system consumes a small amount of AC power (

30) even when it is turned off. In the interest of power

conservation, if you will not be using this system for a long time, unplug it from the household mains socket.

AC mains lead connection

Adhesive tape (supplied)

TV remote control

signal sensor



AC IN



Saving energy

The main unit is designed to conserve its power consumption and save energy.

≥

The main unit will automatically switch to standby mode when no signal is input and no operation is

performed for approx. 20 minutes. Refer to page 24, “AUTO POWER DOWN” to turn this function off.

SC-HTB885EGEB_RQT0A01-B.book 12 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A01

∫ Placement example

On the rear of the main unit:

≥ Connect only after all other connections are completed.

A To a household mains socket

B AC mains lead (supplied)

≥

This system consumes a small amount of AC power (

30) even when it is turned off. In the interest of power

conservation, if you will not be using this system for a long time, unplug it from the household mains socket.

AC mains lead connection

Adhesive tape (supplied)

TV remote control

signal sensor



AC IN



Saving energy

The main unit is designed to conserve its power consumption and save energy.

≥

The main unit will automatically switch to standby mode when no signal is input and no operation is

performed for approx. 20 minutes. Refer to page 24, “AUTO POWER DOWN” to turn this function off.

SC-HTB885EGEB_RQT0A01-B.book 12 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

■

Primjer postavljanja

Na stražnjoj strani glavne jedinice:

Spajanje kabela za napajanje izmjeničnom strujom

● Spojite samo nakon što su završena sva druga spajanja.

A U strujnu utičnicu u kućanstvu

B Kabel za napajanje izmjeničnom strujom (isporučen)

● Sustav troši malu količinu izmjenične struje ( 30), čak i kada je isključen. Radi uštede energije

iskopčajte sustav iz strujne utičnice ako se njime nećete koristiti dulje vrijeme.

Ušteda energije

Glavna je jedinica osmišljena tako da minimalizira potrošnju energije i štedi energiju.

● Glavna će se jedinica automatski prebaciti u stanje čekanja kada približno 20 minuta ne prima

signal i ne izvode se nikakve radnje. Informacije o isključivanju te funkcije potražite na 24. str. u

odjeljku "Automatsko isključivanje".

Ljepljiva traka (isporučena)

Senzor signala

daljinskog

upravljača TV-

prijamnika

Getting started

Precautions

RQT0A01

Step 2 Placement



≥ Do not hold the main unit in one hand to avoid injury, you may drop the main unit when carrying it.

≥ To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.

When carrying the active subwoofer

To avoid interference, maintain the following distances between the main unit/active subwoofer

and other electronic devices that use the same radio frequency (2.4 GHz band).

Safety Precautions

Professional installation is required.

The installation should never be done by any other than a qualified installation specialist.

PANASONIC DISCLAIMS ANY PROPERTY DAMAGE AND/OR SERIOUS INJURY, INCLUDING

DEATH RESULTING FROM IMPROPER INSTALLATION OR INCORRECT HANDLING.

≥ Be sure to install the main unit as indicated within this operating Instructions.

≥ Attach using techniques suited to the structure and materials of the installation location.

Caution

≥ This system is to be used only as indicated in these instructions. Failure to do so may lead to

damage to the amplifier and/or the speaker, and may result in the risk of fire. Consult a qualified

service person if damage has occurred or if you experience a sudden change in performance.

≥ Do not attempt to attach the main unit to a wall using methods other than those described in this

manual.

The active subwoofer

A Do not hold the active subwoofer from this

opening.

The parts inside may get damaged.

B Always hold the bottom of the active subwoofer when

moving it.

Wireless interference

Main unit/active subwoofer

Wireless router, cordless phone and

other electronic devices: approx. 2 m

SC-HTB885EGEB_RQT0A01-B.book 13 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

Precautions

RQT0A01

Step 2 Placement



≥ Do not hold the main unit in one hand to avoid injury, you may drop the main unit when carrying it.

≥ To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.

When carrying the active subwoofer

To avoid interference, maintain the following distances between the main unit/active subwoofer

and other electronic devices that use the same radio frequency (2.4 GHz band).

Safety Precautions

Professional installation is required.

The installation should never be done by any other than a qualified installation specialist.

PANASONIC DISCLAIMS ANY PROPERTY DAMAGE AND/OR SERIOUS INJURY, INCLUDING

DEATH RESULTING FROM IMPROPER INSTALLATION OR INCORRECT HANDLING.

≥ Be sure to install the main unit as indicated within this operating Instructions.

≥ Attach using techniques suited to the structure and materials of the installation location.

Caution

≥ This system is to be used only as indicated in these instructions. Failure to do so may lead to

damage to the amplifier and/or the speaker, and may result in the risk of fire. Consult a qualified

service person if damage has occurred or if you experience a sudden change in performance.

≥ Do not attempt to attach the main unit to a wall using methods other than those described in this

manual.

The active subwoofer

Do not hold the active subwoofer from this

opening.

The parts inside may get damaged.

Always hold the bottom of the active subwoofer when

moving it.

Wireless interference

C Main unit/active subwoofer

D Wireless router, cordless phone and

other electronic devices: approx. 2 m

SC-HTB885EGEB_RQT0A01-B.book 13 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

Mjere oprezaPriprema

2. korak Postavljanje

Mjere opreza

Postavljanje trebaju provesti stručne osobe.

Postavljanje bi trebao provoditi isključivo kvalicirani stručnjak za postavljanje uređaja.

TVRTKA PANASONIC NE PRIHVAĆA ODGOVORNOST ZA OŠTEĆENJE UREĐAJA NITI ZA

OZBILJNE OZLJEDE, UKLJUČUJUĆI SMRT, KOJE NASTANU USLIJED NEISPRAVNOG

POSTAVLJANJA ILI RUKOVANJA.

● Obavezno postavite glavnu jedinicu na način opisan u ovim uputama za uporabu.

● Pričvrstite s pomoću tehnika koje su primjerene za strukturu i materijale lokacije na kojoj ćete postaviti uređaj.

Oprez

● Ovaj se sustav smije upotrebljavati samo na način opisan u ovim uputama. Inače može doći

do oštećenja pojačala i/ili zvučnika te rizika od požara. Ako dođe do oštećenja ili ako se pojave

iznenadne promjene u radu uređaja, obratite se kvaliciranom serviseru.

● Nemojte pokušavati postavljati uređaj na zid na načine koji nisu opisani u ovom priručniku.

● Da biste izbjegli ozljede, glavnu jedinicu nemojte nositi u jednoj ruci jer biste je mogli ispustiti.

● Da biste spriječili oštećenja ili ogrebotine, uređaj položite na mekanu krpu i na njoj ga sastavite.

Aktivni niskotonac

Prenošenje aktivnog niskotonca

Nemojte nositi aktivni niskotonac tako da ga

primite za ovaj otvor.

Unutarnji dijelovi mogu se oštetiti.

Kada pomičete aktivni niskotonac, uvijek ga

pridržavajte za dno.

Bežične smetnje

Da biste izbjegli smetnje, održavajte sljedeće udaljenosti između glavne jedinice/aktivnog

niskotonca i ostalih elektroničkih uređaja koji koriste istu radijsku frekvenciju (područje od 2,4 GHz).

Glavna jedinica/aktivni niskotonac

Bežični usmjerivač, bežični telefon i

ostali elektronički uređaji: približno 2 m

RQT0A01

Choose a placement method that suits you best.

∫ When placing the main unit in front of the TV

The main unit may block or interfere with the TV’s various sensors (C.A.T.S. (Contrast Automatic

Tracking System) sensor, remote control sensor, etc.) and the 3D Eyewear transmitters on a 3D

compatible TV.

≥If interference occurs, move the main unit further away from the TV. If the TV still does not function

correctly, try using it in a rack or in the wall mount position.

∫ If the TV’s remote control sensor is blocked by the main unit

Try using the TV’s remote control from a different angle. If the problem persists, you can use the supplied

IR Blaster to relay the signal to the TV. (> 11, 12)



≥ Place the active subwoofer within a few meters of the main unit and in a horizontal position with the top panel facing upward.

≥ Do not use the main unit or the active subwoofer in a metal cabinet.

≥ Placing the active subwoofer too close to the walls and corners can result in excessive bass. Cover walls and windows with

thick curtains.

≥ If irregular colouring occurs on your TV, turn the TV off for about 30 minutes. If it persists, move the main unit and active

subwoofer further away from the TV.

≥ Keep magnetised items away. Magnetised cards, watches, etc., can be damaged if placed too close to the main unit and active

subwoofer.

Selecting the placement method

When placing the main unit

in a rack or on a table

≥ Place the main unit on a flat

and horizontal surface.

When attaching the main

unit to a wall

≥ Place the main unit on a

flat and vertical surface.

Page 15

Page 16

SC-HTB885EGEB_RQT0A01-B.book 14 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

Odabir načina postavljanja

Odaberite način postavljanja koji vam najbolje odgovara.

■ Postavljanje glavne jedinice ispred TV-prijamnika

Glavna bi jedinica mogla blokirati ili ometati signal raznih senzora TV-prijamnika (senzor C.A.T.S.

(Contrast Automatic Tracking System), senzor daljinskog upravljača itd.) i odašiljača za 3D-naočale na

TV-prijamniku kompatibilnom s tehnologijom 3D.

● Ako dolazi do smetnji, udaljite glavnu jedinicu od TV-prijamnika. Ako TV-prijamnik i dalje ne bude

ispravno radio, pokušajte ga upotrebljavati na polici ili postavljenog na zidu.

■ U slučaju da glavna jedinica blokira senzor daljinskog upravljača TV-prijamnika

Pokušajte upotrebljavati daljinski upravljač TV-prijamnika pod drugim kutom. Ako se problem i dalje

javlja, možete upotrebljavati isporučeni IR Blaster za prijenos signala na TV-prijamnik. ( 11, 12)

● Aktivni niskotonac postavite nekoliko metara od glavne jedinice u vodoravan položaj tako da je gornja ploča okrenuta prema

gore.

● Nemojte upotrebljavati glavnu jedinicu ili aktivni niskotonac u metalnom ormariću.

● Ako niskotonac postavite preblizu zidovima i uglovima, bas može biti prejak. Zidove i prozore prekrijte debelim zavjesama.

● Ako se na TV-prijamniku pojavi neobična boja, isključite ga na otprilike 30 minuta. Ako smetnja ne bude ispravljena, udaljite

glavnu jedinicu i aktivni niskotonac od TV-prijamnika.

● Pazite da u blizini nema magnetiziranih predmeta. Magnetske kartice, satovi i sl., mogu se oštetiti ako ih stavite preblizu

glavnoj jedinici i aktivnom niskotoncu.

15. str.

Postavljanje glavne

jedinice na policu ili stol

● Glavnu jedinicu postavite

na ravnu, vodoravnu

površinu.

Pričvršćivanje glavne

jedinice na zid

● Glavnu jedinicu postavite

na ravnu, okomitu

površinu.

16. str.

Getting started

Precautions

RQT0A01

Additionally required accessories (commercially available)

≥Fall prevention cord ...................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord) ............................................................................. k 2



≥ Use commercially available screws that are capable of supporting over 33 kg.

≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).

Attach the cord to the main unit.

A Cord

§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations,

about 5 mm apart from the tip, at an angle of 45

(as

illustrated above).

Place the main unit in the desired position and attach each cord onto the

rack or table.

≥ Make sure that the slack of the cord is minimal.

≥ Do not lean the main unit against the TV or wall.

B Screw eye

≥Attach at a position capable of supporting over 33 kg.

≥Depending on the placement of the main unit, the screwing position of the screw eye may differ.

When placing the main unit in a rack or on a table





SC-HTB885EGEB_RQT0A01-B.book 15 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

Precautions

RQT0A01

Additionally required accessories (commercially available)

≥Fall prevention cord ...................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord) ............................................................................. k 2



≥ Use commercially available screws that are capable of supporting over 33 kg.

≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).

Attach the cord to the main unit.

A Cord

§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations,

about 5 mm apart from the tip, at an angle of 45

(as

illustrated above).

Place the main unit in the desired position and attach each cord onto the

rack or table.

≥ Make sure that the slack of the cord is minimal.

≥ Do not lean the main unit against the TV or wall.

B Screw eye

≥Attach at a position capable of supporting over 33 kg.

≥Depending on the placement of the main unit, the screwing position of the screw eye may differ.

When placing the main unit in a rack or on a table





SC-HTB885EGEB_RQT0A01-B.book 15 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

Precautions

RQT0A01

Additionally required accessories (commercially available)

≥Fall prevention cord ...................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord) ............................................................................. k 2



≥ Use commercially available screws that are capable of supporting over 33 kg.

≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).

Attach the cord to the main unit.

A Cord

§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations,

about 5 mm apart from the tip, at an angle of 45

(as

illustrated above).

Place the main unit in the desired position and attach each cord onto the

rack or table.

≥ Make sure that the slack of the cord is minimal.

≥ Do not lean the main unit against the TV or wall.

B Screw eye

≥Attach at a position capable of supporting over 33 kg.

≥Depending on the placement of the main unit, the screwing position of the screw eye may differ.

When placing the main unit in a rack or on a table





SC-HTB885EGEB_RQT0A01-B.book 15 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

Precautions

RQT0A01

Additionally required accessories (commercially available)

≥Fall prevention cord ...................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord) ............................................................................. k 2



≥ Use commercially available screws that are capable of supporting over 33 kg.

≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).

Attach the cord to the main unit.

A Cord

§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations,

about 5 mm apart from the tip, at an angle of 45

(as

illustrated above).

Place the main unit in the desired position and attach each cord onto the

rack or table.

≥ Make sure that the slack of the cord is minimal.

≥ Do not lean the main unit against the TV or wall.

B Screw eye

≥Attach at a position capable of supporting over 33 kg.

≥Depending on the placement of the main unit, the screwing position of the screw eye may differ.

When placing the main unit in a rack or on a table





SC-HTB885EGEB_RQT0A01-B.book 15 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

B Vijak s ušicom

● Pričvrstite na mjestu koje ima nosivost preko 33 kg.

● Ovisno o tome kako ćete postaviti glavnu jedinicu, razlikovat će se položaj postavljanja vijka s ušicom.

Mjere oprezaPriprema

Postavljanje glavne jedinice na policu ili stol

Dodatni potrebni pribor (komercijalno dostupan)

● Konop za sprečavanje pada ......................................................................................................... x 2

● Vijak s ušicama (za pričvršćivanje konopa za sprečavanje pada) ................................................ x 2

● Upotrebljavajte komercijalno dostupne vijke koji imaju nosivost preko 33 kg.

● Upotrebljavajte konop koji ima nosivost preko 33 kg (promjera oko 1,5 mm).

Pričvrstite konop na glavnu jedinicu.

A Konop*

* Ako se konop ne može provući kroz rupe, pokušajte ga saviti na 2 mjesta, oko 5 mm od vrha pod

kutom od 45º (kao što je prikazano na prethodnoj slici).

Glavnu jedinicu postavite u željeni položaj i pričvrstite svaki konop na

policu ili stol.

● Konop mora biti u potpunosti zategnut.

● Nemojte naslanjati glavnu jedinicu na TV-prijamnik ili na zid.

RQT0A04

The main unit can be wall mounted using the supplied wall mount brackets, etc. Make sure that the

screw used and the wall are strong enough to support the weight of at least 26 kg.

The screws and other items are not supplied as the type and size will vary with each installation.

≥Refer to step 3 for details about the required screws.

≥Be sure to attach the fall prevention cord as a secondary safety measure.

Supplied accessories

Additionally required accessories (commercially available)

≥Screws for wall mounting............................................................................................................. k 2

≥Fall prevention cord ..................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord)............................................................................ k 2



≥ Use a cord that is capable of supporting over 26 kg (with a diameter of about 1.5 mm).

Attach the cord to the main unit.

A Cord

§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations,

about 5 mm apart from the tip, at an angle of 45

(as

illustrated above).

When attaching the main unit to a wall

∏ 2 Screws ∏ 2 Wall mount brackets



SC-HTB485-EGEBGN_RQT0A04-B.book 16 ページ２０１５年１月２２日　木曜日　午前１０時１５分

RQT0A01

The main unit can be wall mounted using the supplied wall mount brackets, etc. Make sure that the

screw used and the wall are strong enough to support the weight of at least 33 kg.

The screws and other items are not supplied as the type and size will vary with each installation.

≥Refer to step 3 for details about the required screws.

≥Be sure to attach the fall prevention cord as a secondary safety measure.

Supplied accessories

Additionally required accessories (commercially available)

≥Screws for wall mounting............................................................................................................. k 2

≥Fall prevention cord ..................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord)............................................................................ k 2



≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).

Attach the cord to the main unit.

A Cord

§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations,

about 5 mm apart from the tip, at an angle of 45

(as

illustrated above).

When attaching the main unit to a wall

∏ 2 Screws ∏ 2 Wall mount brackets



SC-HTB885EGEB_RQT0A01-B.book 16 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A01

The main unit can be wall mounted using the supplied wall mount brackets, etc. Make sure that the

screw used and the wall are strong enough to support the weight of at least 33 kg.

The screws and other items are not supplied as the type and size will vary with each installation.

≥Refer to step 3 for details about the required screws.

≥Be sure to attach the fall prevention cord as a secondary safety measure.

Supplied accessories

Additionally required accessories (commercially available)

≥Screws for wall mounting............................................................................................................. k 2

≥Fall prevention cord ..................................................................................................................... k 2

≥Screw eyes (to attach the fall prevention cord)............................................................................ k 2



≥ Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm).

Attach the cord to the main unit.

A Cord

§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations,

about 5 mm apart from the tip, at an angle of 45

(as

illustrated above).

When attaching the main unit to a wall

∏ 2 Screws ∏ 2 Wall mount brackets



SC-HTB885EGEB_RQT0A01-B.book 16 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

A Konop*

* Ako se konop ne može provući kroz rupe, pokušajte ga saviti na 2 mjesta, oko 5 mm od vrha pod

kutom od 45º (kao što je prikazano na prethodnoj slici).

Pričvršćivanje glavne jedinice na zid

Glavna se jedinica može pričvrstiti na zid upotrebom isporučenih držača za postavljanje na zid i sl.

Pazite da su vijak koji koristite i zid dovoljno snažni da mogu poduprijeti težinu od najmanje 33 kg.

Vijci i ostali predmeti nisu isporučeni jer se njihova vrsta i veličina razlikuju pri svakom postavljanju.

● Detalje o potrebnim vijcima potražite u 3. koraku.

● Obavezno pričvrstite konop za sprečavanje pada kao sekundarnu mjeru sigurnosti.

Isporučeni pribor

Dodatni potrebni pribor (komercijalno dostupan)

● Vijci za postavljanje na zid .............................................................................................................× 2

● Konop za sprečavanje pada .......................................................................................................... x 2

● Vijak s ušicama (za pričvršćivanje konopa za sprečavanje pada) ................................................. x 2

● Upotrebljavajte konop koji ima nosivost preko 33 kg (promjera oko 1,5 mm).

Pričvrstite konop na glavnu jedinicu.

2 vijka 2 držača za postavljanje na zid

Getting started

Precautions

RQT0A04

Attach the wall mount brackets to the main unit.

A Wall mount bracket (supplied)

B Screw (supplied)

Drive a screw into the wall.

≥ Use the measurements indicated below to identify the screwing positions on the wall.

≥ Leave at least 100 mm of space above of the main unit to allow enough space for fitting the main unit.

≥ Position the main unit with at least 50 mm of free space to its right. If not, it may not be possible to access the buttons.

≥ Be sure to use a level to ensure that both mounting holes are level to each other.

Front view (semi-transparent image)

C At least 30 mm

D ‰4.0 mm

E ‰7.0 mm to ‰9.4 mm

F Wall or pillar

G 1.6 mm to 2.5 mm

H 400 mm I 275 mm J 275 mm

K 27 mm L 110 mm M Wall mounting hole































SC-HTB485-EGEBGN_RQT0A04-B.book 17 ページ２０１５年１月２２日　木曜日　午前１０時１５分

Getting started

Precautions

RQT0A04

Attach the wall mount brackets to the main unit.

A Wall mount bracket (supplied)

B Screw (supplied)

Drive a screw into the wall.

≥ Use the measurements indicated below to identify the screwing positions on the wall.

≥ Leave at least 100 mm of space above of the main unit to allow enough space for fitting the main unit.

≥ Position the main unit with at least 50 mm of free space to its right. If not, it may not be possible to access the buttons.

≥ Be sure to use a level to ensure that both mounting holes are level to each other.

Front view (semi-transparent image)

C At least 30 mm

D ‰4.0 mm

E ‰7.0 mm to ‰9.4 mm

F Wall or pillar

G 1.6 mm to 2.5 mm

H 400 mm I 275 mm J 275 mm

K 27 mm L 110 mm M Wall mounting hole































SC-HTB485-EGEBGN_RQT0A04-B.book 17 ページ２０１５年１月２２日　木曜日　午前１０時１５分

Getting started

Precautions

RQT0A01

Attach the wall mount brackets to the main unit.

A Wall mount bracket (supplied)

B Screw (supplied)

Drive a screw into the wall.

≥ Use the measurements indicated below to identify the screwing positions on the wall.

≥ Leave at least 100 mm of space above of the main unit to allow enough space for fitting the main unit.

≥ Position the main unit with at least 50 mm of free space to its right. If not, it may not be possible to access the touch keys.

≥ Be sure to use a level to ensure that both mounting holes are level to each other.

Front view (semi-transparent image)

C At least 30 mm

D ‰4.0 mm

E ‰7.0 mm to ‰9.4 mm

F Wall or pillar

G 5.5 mm to 6.5 mm

H 400 mm I 380.5 mm J 344.5 mm

K 28 mm L 122.5 mm M Wall mounting hole































SC-HTB885EGEB_RQT0A01-B.book 17 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

Precautions

RQT0A01

Attach the wall mount brackets to the main unit.

A Wall mount bracket (supplied)

B Screw (supplied)

Drive a screw into the wall.

≥ Use the measurements indicated below to identify the screwing positions on the wall.

≥ Leave at least 100 mm of space above of the main unit to allow enough space for fitting the main unit.

≥ Position the main unit with at least 50 mm of free space to its right. If not, it may not be possible to access the touch keys.

≥ Be sure to use a level to ensure that both mounting holes are level to each other.

Front view (semi-transparent image)

C At least 30 mm

D ‰4.0 mm

E ‰7.0 mm to ‰9.4 mm

F Wall or pillar

G 5.5 mm to 6.5 mm

H 400 mm I 380.5 mm J 344.5 mm

K 28 mm L 122.5 mm M Wall mounting hole































SC-HTB885EGEB_RQT0A01-B.book 17 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

Precautions

RQT0A01

Attach the wall mount brackets to the main unit.

A Wall mount bracket (supplied)

B Screw (supplied)

Drive a screw into the wall.

≥ Use the measurements indicated below to identify the screwing positions on the wall.

≥ Leave at least 100 mm of space above of the main unit to allow enough space for fitting the main unit.

≥ Position the main unit with at least 50 mm of free space to its right. If not, it may not be possible to access the touch keys.

≥ Be sure to use a level to ensure that both mounting holes are level to each other.

Front view (semi-transparent image)

At least 30 mm

‰4.0 mm

‰7.0 mm to ‰9.4 mm

Wall or pillar

5.5 mm to 6.5 mm

H 400 mm I 380.5 mm J 344.5 mm

K 28 mm L 122.5 mm M Wall mounting hole































SC-HTB885EGEB_RQT0A01-B.book 17 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

Pričvrstite držače za postavljanje na glavnu jedinicu.

A Držač za postavljanje na zid (isporučen)

B Vijak (isporučen)

Pričvrstite vijak u zid.

● Upotrijebite mjere navedene u nastavku da biste odredili mjesto za postavljanje vijaka na zid.

● Da bi ostalo dovoljno mjesta za postavljanje glavne jedinice, iznad glavne jedinice ostavite najmanje 100 mm prostora.

● Postavite glavnu jedinicu tako da je s njezine desne strane barem 50 mm slobodnog prostora. Inače neće biti moguće

dosegnuti dodirne tipke.

● S pomoću libele provjerite jesu li oba mjesta za postavljanje vijaka vodoravno položena u odnosu jedan na drugi.

Najmanje 30 mm

Ø4,0 mm

Ø7,0 mm do Ø9,4 mm

Zid ili stup

5,5 mm do 6,5 mm

Prednja strana (poluproziran prikaz)

Priprema

Rupa za postavljanje na zid

Mjere opreza

RQT0A04

Fit the main unit securely onto the screw(s).

Secure the cord to the wall.

≥ Make sure that the slack of the cord is minimal.

A Screw eye

B Cord

DO DO NOT

≥ Move the speaker so

that the screw is in

this position.

≥ In this position, the

speaker will likely fall

if moved to the left or

right.





SC-HTB485-EGEBGN_RQT0A04-B.book 18 ページ２０１５年１月２２日　木曜日　午前１０時１５分

RQT0A04

Fit the main unit securely onto the screw(s).

Secure the cord to the wall.

≥ Make sure that the slack of the cord is minimal.

A Screw eye

B Cord

DO DO NOT

≥ Move the speaker so

that the screw is in

this position.

≥ In this position, the

speaker will likely fall

if moved to the left or

right.





SC-HTB485-EGEBGN_RQT0A04-B.book 18 ページ２０１５年１月２２日　木曜日　午前１０時１５分

RQT0A01

Fit the main unit securely onto the screw(s).

Secure the cord to the wall.

≥ Make sure that the slack of the cord is minimal.

A Screw eye

B Cord

DO DO NOT

≥ Move the speaker so

that the screw is in

this position.

≥ In this position, the

speaker will likely fall

if moved to the left or

right.





SC-HTB885EGEB_RQT0A01-B.book 18 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A01

Fit the main unit securely onto the screw(s).

Secure the cord to the wall.

≥ Make sure that the slack of the cord is minimal.

A Screw eye

B Cord

DO DO NOT

≥ Move the speaker so

that the screw is in

this position.

≥ In this position, the

speaker will likely fall

if moved to the left or

right.





SC-HTB885EGEB_RQT0A01-B.book 18 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

Postavite glavnu jedinicu stabilno na vijke.

ISPRAVNO NEISPRAVNO

● Pomaknite zvučnik

tako da vijak bude u

ovom položaju.

● Zvučnik bi u ovom

položaju mogao pasti

pomakne li ga se

ulijevo ili udesno.

Pričvrstite konop na zid.

● Konop mora biti u potpunosti zategnut.

A Vijak s ušicom

B Konop

SQT0852

4 Fit the main unit securely onto the screw(s).

5 Secure the cord to the wall.

≥ Make sure that the slack of the cord is minimal.

A Screw eye

B Cord

DO DO NOT

≥ Move the speaker so

that the screw is in

this position.

≥ In this position, the

speaker will likely fall

if moved to the left or

right.





SC-HTB690-SQT0852.book 18 ページ２０１５年３月２０日　金曜日　午後６時１７分

SQT0852

4 Fit the main unit securely onto the screw(s).

5 Secure the cord to the wall.

≥ Make sure that the slack of the cord is minimal.

A Screw eye

B Cord

DO DO NOT

≥ Move the speaker so

that the screw is in

this position.

≥ In this position, the

speaker will likely fall

if moved to the left or

right.





SC-HTB690-SQT0852.book 18 ページ２０１５年３月２０日　金曜日　午後６時１７分

Getting started

Precautions

RQT0A04

Step 3 Wireless connections

Preparation

≥ Turn on the main unit.

Press [BÍ CI].

Active subwoofer on/off button [B Í C I]

Use this button to turn the active subwoofer on

and off.

C I:

The active subwoofer is on.

B Í

The active subwoofer is off.

The active subwoofer will still consume a small

amount of power even when it is turned off (

Check that the wireless link is

activated.

WIRELESS LINK indicator

Lights red:

The wireless link is not activated.

Lights green:

The wireless link is activated.

Blinks green:

The active subwoofer is trying to activate the

wireless link with the main unit.



The wireless link will be activated when the main unit and the

active subwoofer are both turned on.

By using the Bluetooth

connection, you can listen

to the sound from the Bluetooth

audio device

from this system wirelessly.

≥ Refer to the operating instructions of the Bluetooth

device

for further instruction on how to connect a Bluetooth

device.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near the main unit.

Press [ ] to select “BLUETOOTH”.

≥ If “PAIRING” is indicated on the display, go to step 3.

Press and hold [ ] until “PAIRING”

is indicated on the display.

Select “SC-HTB485” from the

Bluetooth

device’s Bluetooth

menu.

≥

If prompted for the passkey on the Bluetooth

device, enter “0000”.

≥ Once the Bluetooth

device is connected, the name of the

connected device will be indicated on the display for a few

seconds.



≥ You can register up to 8 devices with this system. If a 9th

device is paired, the device that has not been used for the

longest time will be replaced.

Press [ ] to enter Bluetooth

mode.

“BLUETOOTH READY” is indicated on the display.

Select “SC-HTB485” from the

Bluetooth

device’s Bluetooth

menu.

∫ Disconnecting a Bluetooth

device

Press and hold [ ] until the “BLUETOOTH

READY” is indicated on the display.



≥ When “BLUETOOTH” is selected as the source, this

system will automatically try and connect to the last

connected Bluetooth

device.

≥ The Bluetooth

device will be disconnected if a different

audio source (e.g. “TV”) is selected.

≥

This system can only be connected to one device at a time.

≥

To change the sound quality, refer to page 24 “LINK MODE”.

Active subwoofer

wireless connection

Bluetooth

connection

Bluetooth

pairing

Connecting a paired

Bluetooth

device

SC-HTB485-EGEBGN_RQT0A04-B.book 19 ページ２０１５年１月２２日　木曜日　午前１０時１５分

Getting started

Precautions

RQT0A04

Step 3 Wireless connections

Preparation

≥ Turn on the main unit.

Press [BÍ CI].

Active subwoofer on/off button [B Í C I]

Use this button to turn the active subwoofer on

and off.

C I:

The active subwoofer is on.

B Í

The active subwoofer is off.

The active subwoofer will still consume a small

amount of power even when it is turned off (

Check that the wireless link is

activated.

WIRELESS LINK indicator

Lights red:

The wireless link is not activated.

Lights green:

The wireless link is activated.

Blinks green:

The active subwoofer is trying to activate the

wireless link with the main unit.



The wireless link will be activated when the main unit and the

active subwoofer are both turned on.

By using the Bluetooth

connection, you can listen

to the sound from the Bluetooth

audio device

from this system wirelessly.

≥ Refer to the operating instructions of the Bluetooth

device

for further instruction on how to connect a Bluetooth

device.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near the main unit.

Press [ ] to select “BLUETOOTH”.

≥ If “PAIRING” is indicated on the display, go to step 3.

Press and hold [ ] until “PAIRING”

is indicated on the display.

Select “SC-HTB485” from the

Bluetooth

device’s Bluetooth

menu.

≥

If prompted for the passkey on the Bluetooth

device, enter “0000”.

≥ Once the Bluetooth

device is connected, the name of the

connected device will be indicated on the display for a few

seconds.



≥ You can register up to 8 devices with this system. If a 9th

device is paired, the device that has not been used for the

longest time will be replaced.

Press [ ] to enter Bluetooth

mode.

“BLUETOOTH READY” is indicated on the display.

Select “SC-HTB485” from the

Bluetooth

device’s Bluetooth

menu.

∫ Disconnecting a Bluetooth

device

Press and hold [ ] until the “BLUETOOTH

READY” is indicated on the display.



≥ When “BLUETOOTH” is selected as the source, this

system will automatically try and connect to the last

connected Bluetooth

device.

≥ The Bluetooth

device will be disconnected if a different

audio source (e.g. “TV”) is selected.

≥

This system can only be connected to one device at a time.

≥

To change the sound quality, refer to page 24 “LINK MODE”.

Active subwoofer

wireless connection

Bluetooth

connection

Bluetooth

pairing

Connecting a paired

Bluetooth

device

SC-HTB485-EGEBGN_RQT0A04-B.book 19 ページ２０１５年１月２２日　木曜日　午前１０時１５分

Getting started

Precautions

RQT0A04

Step 3 Wireless connections

Preparation

≥ Turn on the main unit.

Press [BÍ CI].

Active subwoofer on/off button [B Í C I]

Use this button to turn the active subwoofer on

and off.

C I:

The active subwoofer is on.

B Í

The active subwoofer is off.

The active subwoofer will still consume a small

amount of power even when it is turned off (

Check that the wireless link is

activated.

WIRELESS LINK indicator

Lights red:

The wireless link is not activated.

Lights green:

The wireless link is activated.

Blinks green:

The active subwoofer is trying to activate the

wireless link with the main unit.



The wireless link will be activated when the main unit and the

active subwoofer are both turned on.

By using the Bluetooth

connection, you can listen

to the sound from the Bluetooth

audio device

from this system wirelessly.

≥ Refer to the operating instructions of the Bluetooth

device

for further instruction on how to connect a Bluetooth

device.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near the main unit.

Press [ ] to select “BLUETOOTH”.

≥ If “PAIRING” is indicated on the display, go to step 3.

Press and hold [ ] until “PAIRING”

is indicated on the display.

Select “SC-HTB485” from the

Bluetooth

device’s Bluetooth

menu.

≥

If prompted for the passkey on the Bluetooth

device, enter “0000”.

≥ Once the Bluetooth

device is connected, the name of the

connected device will be indicated on the display for a few

seconds.



≥ You can register up to 8 devices with this system. If a 9th

device is paired, the device that has not been used for the

longest time will be replaced.

Press [ ] to enter Bluetooth

mode.

“BLUETOOTH READY” is indicated on the display.

Select “SC-HTB485” from the

Bluetooth

device’s Bluetooth

menu.

∫ Disconnecting a Bluetooth

device

Press and hold [ ] until the “BLUETOOTH

READY” is indicated on the display.



≥ When “BLUETOOTH” is selected as the source, this

system will automatically try and connect to the last

connected Bluetooth

device.

≥ The Bluetooth

device will be disconnected if a different

audio source (e.g. “TV”) is selected.

≥

This system can only be connected to one device at a time.

≥

To change the sound quality, refer to page 24 “LINK MODE”.

Active subwoofer

wireless connection

Bluetooth

connection

Bluetooth

pairing

Connecting a paired

Bluetooth

device

SC-HTB485-EGEBGN_RQT0A04-B.book 19 ページ２０１５年１月２２日　木曜日　午前１０時１５分

Getting started

Precautions

RQT0A04

Step 3 Wireless connections

Preparation

≥ Turn on the main unit.

Press [BÍ CI].

Active subwoofer on/off button [B Í C I]

Use this button to turn the active subwoofer on

and off.

C I:

The active subwoofer is on.

B Í

The active subwoofer is off.

The active subwoofer will still consume a small

amount of power even when it is turned off (

Check that the wireless link is

activated.

WIRELESS LINK indicator

Lights red:

The wireless link is not activated.

Lights green:

The wireless link is activated.

Blinks green:

The active subwoofer is trying to activate the

wireless link with the main unit.



The wireless link will be activated when the main unit and the

active subwoofer are both turned on.

By using the Bluetooth

connection, you can listen

to the sound from the Bluetooth

audio device

from this system wirelessly.

≥ Refer to the operating instructions of the Bluetooth

device

for further instruction on how to connect a Bluetooth

device.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near the main unit.

Press [ ] to select “BLUETOOTH”.

≥ If “PAIRING” is indicated on the display, go to step 3.

Press and hold [ ] until “PAIRING”

is indicated on the display.

Select “SC-HTB485” from the

Bluetooth

device’s Bluetooth

menu.

≥

If prompted for the passkey on the Bluetooth

device, enter “0000”.

≥ Once the Bluetooth

device is connected, the name of the

connected device will be indicated on the display for a few

seconds.



≥ You can register up to 8 devices with this system. If a 9th

device is paired, the device that has not been used for the

longest time will be replaced.

Press [ ] to enter Bluetooth

mode.

“BLUETOOTH READY” is indicated on the display.

Select “SC-HTB485” from the

Bluetooth

device’s Bluetooth

menu.

∫ Disconnecting a Bluetooth

device

Press and hold [ ] until the “BLUETOOTH

READY” is indicated on the display.



≥ When “BLUETOOTH” is selected as the source, this

system will automatically try and connect to the last

connected Bluetooth

device.

≥ The Bluetooth

device will be disconnected if a different

audio source (e.g. “TV”) is selected.

≥

This system can only be connected to one device at a time.

≥

To change the sound quality, refer to page 24 “LINK MODE”.

Active subwoofer

wireless connection

Bluetooth

connection

Bluetooth

pairing

Connecting a paired

Bluetooth

device

SC-HTB485-EGEBGN_RQT0A04-B.book 19 ページ２０１５年１月２２日　木曜日　午前１０時１５分

Getting started

Precautions

RQT0A01

Step 3 Wireless connections

Preparation

≥ Turn on the main unit.

Press [BÍ CI].

Active subwoofer on/off button [B Í C I]

Use this button to turn the active subwoofer on

and off.

C I:

The active subwoofer is on.

B Í

The active subwoofer is off.

The active subwoofer will still consume a small

amount of power even when it is turned off (

Check that the wireless link is

activated.

WIRELESS LINK indicator

Lights red:

The wireless link is not activated.

Lights green:

The wireless link is activated.

Blinks green:

The active subwoofer is trying to activate the

wireless link with the main unit.



The wireless link will be activated when the main unit and the

active subwoofer are both turned on.

By using the Bluetooth

connection, you can listen

to the sound from the Bluetooth

audio device

from this system wirelessly.

≥

Refer to the operating instructions of the Bluetooth

device for

further instruction on how to connect a Bluetooth

device.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near the main unit.

Press [ ] to select “BLUETOOTH”.

≥ If “PAIRING” is indicated on the display, go to step 3.

Press and hold [ ] until “PAIRING”

is indicated on the display.

Select “SC-HTB885” from the

Bluetooth

device’s Bluetooth

menu.

≥

If prompted for the passkey on the Bluetooth

device, enter “0000”.

≥

Once the Bluetooth

device is connected, the name of the

connected device will be indicated on the display for a few seconds.



≥ You can register up to 8 devices with this system. If a 9th

device is paired, the device that has not been used for the

longest time will be replaced.

Press [ ] to select Bluetooth

mode.

≥

If “BLUETOOTH READY” is indicated on the display, go to step 3.

Press and hold [ ] until

“BLUETOOTH READY” is indicated

on the display.

Select “SC-HTB885” from the

Bluetooth

device’s Bluetooth

menu.

∫ Disconnecting a Bluetooth

device

Press and hold [ ] until the “BLUETOOTH

READY” is indicated on the display.



≥ When “BLUETOOTH” is selected as the source, this

system will automatically try and connect to the last

connected Bluetooth

device.

≥

This system can only be connected to one device at a time.

≥

To change the sound quality, refer to page 24 “LINK MODE”.

Active subwoofer

wireless connection

Bluetooth

connection

Bluetooth

pairing

Connecting a paired

Bluetooth

device

SC-HTB885EGEB_RQT0A01-B.book 19 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

Precautions

RQT0A01

Step 3 Wireless connections

Preparation

≥ Turn on the main unit.

Press [BÍ CI].

Active subwoofer on/off button [B Í C I]

Use this button to turn the active subwoofer on

and off.

C I:

The active subwoofer is on.

B Í

The active subwoofer is off.

The active subwoofer will still consume a small

amount of power even when it is turned off (

Check that the wireless link is

activated.

WIRELESS LINK indicator

Lights red:

The wireless link is not activated.

Lights green:

The wireless link is activated.

Blinks green:

The active subwoofer is trying to activate the

wireless link with the main unit.



The wireless link will be activated when the main unit and the

active subwoofer are both turned on.

By using the Bluetooth

connection, you can listen

to the sound from the Bluetooth

audio device

from this system wirelessly.

≥

Refer to the operating instructions of the Bluetooth

device for

further instruction on how to connect a Bluetooth

device.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near the main unit.

Press [ ] to select “BLUETOOTH”.

≥ If “PAIRING” is indicated on the display, go to step 3.

Press and hold [ ] until “PAIRING”

is indicated on the display.

Select “SC-HTB885” from the

Bluetooth

device’s Bluetooth

menu.

≥

If prompted for the passkey on the Bluetooth

device, enter “0000”.

≥

Once the Bluetooth

device is connected, the name of the

connected device will be indicated on the display for a few seconds.



≥ You can register up to 8 devices with this system. If a 9th

device is paired, the device that has not been used for the

longest time will be replaced.

Press [ ] to select Bluetooth

mode.

≥

If “BLUETOOTH READY” is indicated on the display, go to step 3.

Press and hold [ ] until

“BLUETOOTH READY” is indicated

on the display.

Select “SC-HTB885” from the

Bluetooth

device’s Bluetooth

menu.

∫ Disconnecting a Bluetooth

device

Press and hold [ ] until the “BLUETOOTH

READY” is indicated on the display.



≥ When “BLUETOOTH” is selected as the source, this

system will automatically try and connect to the last

connected Bluetooth

device.

≥

This system can only be connected to one device at a time.

≥

To change the sound quality, refer to page 24 “LINK MODE”.

Active subwoofer

wireless connection

Bluetooth

connection

Bluetooth

pairing

Connecting a paired

Bluetooth

device

SC-HTB885EGEB_RQT0A01-B.book 19 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

Precautions

RQT0A01

Step 3 Wireless connections

Preparation

≥ Turn on the main unit.

Press [BÍ CI].

Active subwoofer on/off button [B Í C I]

Use this button to turn the active subwoofer on

and off.

C I:

The active subwoofer is on.

B Í

The active subwoofer is off.

The active subwoofer will still consume a small

amount of power even when it is turned off (

Check that the wireless link is

activated.

WIRELESS LINK indicator

Lights red:

The wireless link is not activated.

Lights green:

The wireless link is activated.

Blinks green:

The active subwoofer is trying to activate the

wireless link with the main unit.



The wireless link will be activated when the main unit and the

active subwoofer are both turned on.

By using the Bluetooth

connection, you can listen

to the sound from the Bluetooth

audio device

from this system wirelessly.

≥

Refer to the operating instructions of the Bluetooth

device for

further instruction on how to connect a Bluetooth

device.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near the main unit.

Press [ ] to select “BLUETOOTH”.

≥ If “PAIRING” is indicated on the display, go to step 3.

Press and hold [ ] until “PAIRING”

is indicated on the display.

Select “SC-HTB885” from the

Bluetooth

device’s Bluetooth

menu.

≥

If prompted for the passkey on the Bluetooth

device, enter “0000”.

≥

Once the Bluetooth

device is connected, the name of the

connected device will be indicated on the display for a few seconds.



≥ You can register up to 8 devices with this system. If a 9th

device is paired, the device that has not been used for the

longest time will be replaced.

Press [ ] to select Bluetooth

mode.

≥

If “BLUETOOTH READY” is indicated on the display, go to step 3.

Press and hold [ ] until

“BLUETOOTH READY” is indicated

on the display.

Select “SC-HTB885” from the

Bluetooth

device’s Bluetooth

menu.

∫ Disconnecting a Bluetooth

device

Press and hold [ ] until the “BLUETOOTH

READY” is indicated on the display.



≥ When “BLUETOOTH” is selected as the source, this

system will automatically try and connect to the last

connected Bluetooth

device.

≥

This system can only be connected to one device at a time.

≥

To change the sound quality, refer to page 24 “LINK MODE”.

Active subwoofer

wireless connection

Bluetooth

connection

Bluetooth

pairing

Connecting a paired

Bluetooth

device

SC-HTB885EGEB_RQT0A01-B.book 19 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

Precautions

RQT0A01

Step 3 Wireless connections

Preparation

≥ Turn on the main unit.

Press [BÍ CI].

Active subwoofer on/off button [B Í C I]

Use this button to turn the active subwoofer on

and off.

C I:

The active subwoofer is on.

B Í

The active subwoofer is off.

The active subwoofer will still consume a small

amount of power even when it is turned off (

Check that the wireless link is

activated.

WIRELESS LINK indicator

Lights red:

The wireless link is not activated.

Lights green:

The wireless link is activated.

Blinks green:

The active subwoofer is trying to activate the

wireless link with the main unit.



The wireless link will be activated when the main unit and the

active subwoofer are both turned on.

By using the Bluetooth

connection, you can listen

to the sound from the Bluetooth

audio device

from this system wirelessly.

≥

Refer to the operating instructions of the Bluetooth

device for

further instruction on how to connect a Bluetooth

device.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near the main unit.

Press [ ] to select “BLUETOOTH”.

≥ If “PAIRING” is indicated on the display, go to step 3.

Press and hold [ ] until “PAIRING”

is indicated on the display.

Select “SC-HTB885” from the

Bluetooth

device’s Bluetooth

menu.

≥

If prompted for the passkey on the Bluetooth

device, enter “0000”.

≥

Once the Bluetooth

device is connected, the name of the

connected device will be indicated on the display for a few seconds.



≥ You can register up to 8 devices with this system. If a 9th

device is paired, the device that has not been used for the

longest time will be replaced.

Press [ ] to select Bluetooth

mode.

≥

If “BLUETOOTH READY” is indicated on the display, go to step 3.

Press and hold [ ] until

“BLUETOOTH READY” is indicated

on the display.

Select “SC-HTB885” from the

Bluetooth

device’s Bluetooth

menu.

∫ Disconnecting a Bluetooth

device

Press and hold [ ] until the “BLUETOOTH

READY” is indicated on the display.



≥ When “BLUETOOTH” is selected as the source, this

system will automatically try and connect to the last

connected Bluetooth

device.

≥

This system can only be connected to one device at a time.

≥

To change the sound quality, refer to page 24 “LINK MODE”.

Active subwoofer

wireless connection

Bluetooth

connection

Bluetooth

pairing

Connecting a paired

Bluetooth

device

SC-HTB885EGEB_RQT0A01-B.book 19 ページ２０１５年１月２９日　木曜日　午後３時４５分

Getting started

Precautions

RQT0A01

Step 3 Wireless connections

Preparation

≥ Turn on the main unit.

Press [BÍ CI].

Active subwoofer on/off button [B Í C I]

Use this button to turn the active subwoofer on

and off.

C I:

The active subwoofer is on.

B Í

The active subwoofer is off.

The active subwoofer will still consume a small

amount of power even when it is turned off (

Check that the wireless link is

activated.

WIRELESS LINK indicator

Lights red:

The wireless link is not activated.

Lights green:

The wireless link is activated.

Blinks green:

The active subwoofer is trying to activate the

wireless link with the main unit.



The wireless link will be activated when the main unit and the

active subwoofer are both turned on.

By using the Bluetooth

connection, you can listen

to the sound from the Bluetooth

audio device

from this system wirelessly.

≥

Refer to the operating instructions of the Bluetooth

device for

further instruction on how to connect a Bluetooth

device.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near the main unit.

Press [ ] to select “BLUETOOTH”.

≥ If “PAIRING” is indicated on the display, go to step 3.

Press and hold [ ] until “PAIRING”

is indicated on the display.

Select “SC-HTB885” from the

Bluetooth

device’s Bluetooth

menu.

≥

If prompted for the passkey on the Bluetooth

device, enter “0000”.

≥

Once the Bluetooth

device is connected, the name of the

connected device will be indicated on the display for a few seconds.



≥ You can register up to 8 devices with this system. If a 9th

device is paired, the device that has not been used for the

longest time will be replaced.

Press [ ] to select Bluetooth

mode.

≥

If “BLUETOOTH READY” is indicated on the display, go to step 3.

Press and hold [ ] until

“BLUETOOTH READY” is indicated

on the display.

Select “SC-HTB885” from the

Bluetooth

device’s Bluetooth

menu.

∫ Disconnecting a Bluetooth

device

Press and hold [ ] until the “BLUETOOTH

READY” is indicated on the display.



≥ When “BLUETOOTH” is selected as the source, this

system will automatically try and connect to the last

connected Bluetooth

device.

≥

This system can only be connected to one device at a time.

≥

To change the sound quality, refer to page 24 “LINK MODE”.

Active subwoofer

wireless connection

Bluetooth

connection

Bluetooth

pairing

Connecting a paired

Bluetooth

device

SC-HTB885EGEB_RQT0A01-B.book 19 ページ２０１５年１月２９日　木曜日　午後３時４５分

RQT0A04

Bežično spajanje aktivnog

niskotonca

Priprema

● Uključite glavnu jedinicu.

Pritisnite [ ].

Gumb za uklj./isklj. aktivnog niskotonca

[ ]

Upotrebljavajte ovaj gumb da biste uključili i

isključili aktivni niskotonac.

Aktivni je niskotonac uključen.

Aktivni je niskotonac isključen.

Aktivni niskotonac i dalje će trošiti malu količinu

energije, čak i kada je isključen ( , ).

Provjerite je li aktivirana bežična veza.

Pokazatelj WIRELESS LINK (Bežična veza)

Svijetli crveno:

Bežična veza nije aktivirana.

Svijetli zeleno:

Bežična je veza aktivirana.

Treperi zeleno:

Aktivni niskotonac pokušava aktivirati bežičnu

vezu s glavnom jedinicom.

Bežična će se veza aktivirat kada se uključe glavna

jedinica i aktivni niskotonac.

Spajanje s Bluetoothom

Korištenjem Bluetooth

veze možete bežično slušati

zvuk iz Bluetooth

audiouređaja na ovom sustavu.

● Daljnje upute o spajanju Bluetooth

uređaja potražite u

uputama za uporabu Bluetooth

uređaja.

Priprema

● Uključite funkciju Bluetooth

na uređaju i

postavite uređaj blizu glavne jedinice.

Uparivanje s Bluetoothom

Pritisnite [ ] da biste odabrali

“BLUETOOTH”.

● Ako je na zaslonu navedeno "PAIRING" (Uparivanje),

idite na 3. korak.

Pritisnite i držite [ ] dok se ne prikaže

“PAIRING” (Uparivanje) na prikazu.

Odaberite “SC-HTB885” iz Bluetooth

izbornika Bluetooth

uređaja.

● Ako vas Bluetooth

uređaj zatraži ključ, unesite “0000”.

● Kada se Bluetooth

uređaj spoji, naziv spojenog uređaja

prikazat će se na prikazu na nekoliko sekundi.

● Možete memorirati do 8 uređaja pomoću ovog sustava.

Ako uparite deveti uređaj, uređaj koji najdulje nije

korišten bit će zamijenjen.

Povezivanje uparenog

Bluetooth

uređaja

Pritisnite [ ] da biste odabrali

Bluetooth

način rada.

● Ako je na prikazu navedeno "BLUETOOTH READY"

(Bluetooth je spreman), idite na 3. korak.

Pritisnite i držite [ ] dok se ne prikaže

“BLUETOOTH READY” na prikazu.

Odaberite “SC-HTB885” iz Bluetooth

izbornika Bluetooth

uređaja.

■ Odspajanje Bluetooth

uređaja

Pritisnite i držite [ ] dok se ne prikaže

“BLUETOOTH READY” na prikazu.

● Kada je kao izvor odabran "BLUETOOTH" ovaj će se

sustav automatski pokušati spojiti na zadnji spojeni

Bluetooth

uređaj.

● Ovaj sustav može istovremeno biti spojen samo na jedan

uređaj.

● Informacije o promjeni kvalitete zvuka potražite na 24.

stranici "LINK MODE" (Način povezivanja).

3. korak Bežične veze

Priprema Mjere opreza

RQT0A04

For NFC-compatible Bluetooth

devices

(Android

devices) only

Simply by touching an NFC (Near Field

Communication)-compatible Bluetooth

device on

the main unit, you can complete all preparations,

from registering a Bluetooth

device to

establishing a connection.

Preparation

≥ Turn on the NFC feature of the device.

≥ Android device version lower than 4.1 requires

the installation of the app “Panasonic Music

Streaming” (free of charge).

Enter “Panasonic Music Streaming” in the search

box of Google Play

to search, and then select

“Panasonic Music Streaming”.

2 Start the app “Panasonic Music Streaming” on the

device.

– Follow on-screen instructions on your device.

– Always use the latest version of the app.

Press [ ] to select “BLUETOOTH”.

Touch and hold your device on the

NFC touch area of the main unit [ ].

(> 6)

Do not move the Bluetooth

device until it beeps,

displays a message or reacts in some way.

Once the Bluetooth

device has reacted, move the

device away from the main unit.

≥When the registration and connection of the Bluetooth

device is complete, the name of the connected device is

indicated on the display for a few seconds.

≥The location of the NFC touch area differs depending on

the device. When a connection cannot be established

even if your Bluetooth

device has touched the NFC

touch area of the main unit, change the position of the

device. The condition may also improve if you download

the dedicated app “Panasonic Music Streaming” and

start it up.

Start playback on the Bluetooth

device.



≥ If you touch another device to the main unit, you can

update the Bluetooth

connection. The previously

connected device will be disconnected automatically.

≥ When the connection is established, playback may start

automatically depending on the type of device being used.

≥ The One-Touch Connection may not work properly

depending on the type of device being used.

Remote control code

When other Panasonic devices respond to this

system’s remote control, change the remote

control code on this system and the remote

control.

Preparation

≥ Turn off all other Panasonic products.

≥ Turn on the main unit.

∫ To set the code to “REMOTE 2”

Press and hold [MUTE] and [OK] for more than

4 sec.

“REMOTE 2” is indicated on the display.

∫ To set the code to “REMOTE 1”

Press and hold [MUTE] and [4] for more than

4 sec.

“REMOTE 1” is indicated on the display.

One-Touch Connection

(Connecting by NFC)

SC-HTB485-EGEBGN_RQT0A04-B.book 20 ページ２０１５年１月２２日　木曜日　午前１０時１５分

RQT0A04

For NFC-compatible Bluetooth

devices

(Android

devices) only

Simply by touching an NFC (Near Field

Communication)-compatible Bluetooth

device on

the main unit, you can complete all preparations,

from registering a Bluetooth

device to

establishing a connection.

Preparation

≥ Turn on the NFC feature of the device.

≥ Android device version lower than 4.1 requires

the installation of the app “Panasonic Music

Streaming” (free of charge).

Enter “Panasonic Music Streaming” in the search

box of Google Play

to search, and then select

“Panasonic Music Streaming”.

2 Start the app “Panasonic Music Streaming” on the

device.

– Follow on-screen instructions on your device.

– Always use the latest version of the app.

Press [ ] to select “BLUETOOTH”.

Touch and hold your device on the

NFC touch area of the main unit [ ].

(> 6)

Do not move the Bluetooth

device until it beeps,

displays a message or reacts in some way.

Once the Bluetooth

device has reacted, move the

device away from the main unit.

≥When the registration and connection of the Bluetooth

device is complete, the name of the connected device is

indicated on the display for a few seconds.

≥The location of the NFC touch area differs depending on

the device. When a connection cannot be established

even if your Bluetooth

device has touched the NFC

touch area of the main unit, change the position of the

device. The condition may also improve if you download

the dedicated app “Panasonic Music Streaming” and

start it up.

Start playback on the Bluetooth

device.



≥ If you touch another device to the main unit, you can

update the Bluetooth

connection. The previously

connected device will be disconnected automatically.

≥ When the connection is established, playback may start

automatically depending on the type of device being used.

≥ The One-Touch Connection may not work properly

depending on the type of device being used.

Remote control code

When other Panasonic devices respond to this

system’s remote control, change the remote

control code on this system and the remote

control.

Preparation

≥ Turn off all other Panasonic products.

≥ Turn on the main unit.

∫ To set the code to “REMOTE 2”

Press and hold [MUTE] and [OK] for more than

4 sec.

“REMOTE 2” is indicated on the display.

∫ To set the code to “REMOTE 1”

Press and hold [MUTE] and [4] for more than

4 sec.

“REMOTE 1” is indicated on the display.

One-Touch Connection

(Connecting by NFC)

SC-HTB485-EGEBGN_RQT0A04-B.book 20 ページ２０１５年１月２２日　木曜日　午前１０時１５分

RQT0A04

Povezivanje jednim dodirom

(Povezivanje putem NFC-a)

Samo za Bluetooth

uređaje (uređaje sa

sustavom Android™) kompatibilne s NFC-om

Ako samo prislonite Bluetooth

uređaj kompatibilan

s NFC-om (Near Field Communication)

(Komunikacija bliskog polja) na glavnu jedinicu,

možete završiti sve pripreme od registriranja

Bluetooth

uređaja do uspostavljanja veze.

Priprema

● Uključite značajku NFC na uređaju.

● Za uređaje s inačicom Androida starijom od

inačice 4.1 potrebna je instalacija besplatne

aplikacije "Panasonic Music Streaming".

1 Unesite "Panasonic Music Streaming" u polje za

pretraživanje Google Play™ da biste pretraživali

pa odaberite "Panasonic Music Streaming".

2 Pokrenite aplikaciju "Panasonic Music Streaming"

na uređaju.

– Slijedite zaslonske upute na svom uređaju.

– Uvijek upotrebljavajte najnoviju inačicu aplikacije.

Pritisnite [ ] da biste odabrali

“BLUETOOTH”.

Prislonite i držite uređaj na NFC-

području osjetljivom na dodir na

glavnoj jedinici [ ]. ( 6)

Nemojte pomicati Bluetooth

uređaj dok ne ispusti

zvučni signal, prikaže poruku ili reagira na neki način.

Nakon što Bluetooth

uređaj reagira, odmaknite

uređaj od glavne jedinice.

● Kada dovršite registraciju i spajanje Bluetooth

uređaja, naziv spojenog uređaja prikazat će se na

prikazu na nekoliko sekundi.

● Položaj NFC-područja osjetljivog na dodir razlikuje

se ovisno o uređaju. Ako se veza ne može

uspostaviti čak i nakon što ste dodirnuli NFC-

područje osjetljivo na dodir na glavnoj jedinici sa

svojim Bluetooth

uređajem, promijenite položaj

uređaja ili glavne jedinice. Stanje možete poboljšati

i ako preuzmete i pokrenete namjensku aplikaciju

“Panasonic Music Streaming”.

Pokrenite reprodukciju na Bluetooth

uređaju.

● Ako prislonite drugi uređaj na glavnu jedinicu, možete

ažurirati Bluetooth

vezu. Veza s prethodno spojenim

uređajem automatski će se prekinuti.

● Nakon što se veza uspostavi, reprodukcija se može

pokrenuti automatski ovisno o vrsti korištenog uređaja.

● Povezivanje jednim dodirom možda neće ispravno raditi,

ovisno o vrsti uređaja koji se upotrebljava.

Kod daljinskog

upravljača

Kada ostali Panasonicovi uređaji reagiraju na

daljinski upravljač ovog sustava, promijenite

kod na daljinskom upravljaču ovog sustava i

daljinskom upravljaču.

Priprema

● Isključite sve ostale Panasonicove proizvode.

● Uključite glavnu jedinicu.

■ Postavljanje koda na postavku

“REMOTE 2” (Daljinski upravljač 2)

Pritisnite i držite [MUTE] (Bez zvuka) i [OK]

(U redu) dulje od 4 sekunde.

Na prikazu se prikazuje "REMOTE 2" (Daljinski

upravljač 2).

■ Postavljanje koda na postavku

“REMOTE 1” (Daljinski upravljač 1)

Pritisnite i držite [MUTE] (Bez zvuka) i [▼]

dulje od 4 sekunde.

Na prikazu se prikazuje "REMOTE 1" (Daljinski

upravljač 1).

Page is loading ...

Panasonic SCHTB885EG Operating instructions

Panasonic SCHTB885EG Operating instructions

Panasonic SCHTB885EG Operating instructions

Related papers

Other documents