2. Home
  3. Home security & automation
  4. Security camera accessories
  5. Interlogix
  6. TruVision Turret Adapter Plate
TruVision Turret Adapter Plate

Interlogix TruVision Turret Adapter Plate Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Interlogix TruVision Turret Adapter Plate Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the Interlogix TruVision Turret Adapter Plate used for?
    What is included with the Turret Adapter Plate?
    What are the dimensions of the Turret Adapter Plate?
    What is the weight of the Turret Adapter Plate?
    What types of cameras are supported by the Turret Adapter Plate?
    How do I attach a turret camera to a double-gang box using the Turret Adapter Plate?
    How do I attach a turret camera to a TVD-BB3A dome angled back box using the Turret Adapter Plate?
© 2017 United Technologies Corporation. P/N 1073275-EN • REV A • ISS 06FEB17
Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. All rights reserved.
Turret Adapter Plate Installation Instructions
The Turret Adapter Plate is used when attaching a fixed or
motorized lens turret camera to a double-gang box, or to a
TVD-BB3 or TVD-BB3A back box, or to a TVD-M2-WM wall
mount, or to a TVD-CB3 cup base. The turret adapter plate is
included with the turret camera.
Refer to the Installation Guide for the turret camera you are
installing for the details on the camera housing (assembling/
disassembling) and cable connections.
Description
D
imensions: 140 × 2 mm (5.51 × 0.08 in.)
Weight
: 70 g (0.15 lb.)
Accessories:
Screw
A
KM 4 × 8 mm (4 pcs)
(Used to attach the turret adapter plate to the
wall mount, back box or cup base)
Screw
B
PM 4 × 8 mm (3 pcs)
(Used to attach the turret camera to the
adapter plate)
Screw
C
PM 6-32 × 10 mm (4 pcs)
(Used to attach the turret adapter plate to a
double-gang electrical box)
Supported
equipment:
Hole 1
TruVision IP Fixed Lens Turret Cameras
TVT-5301, TVT-5302, TVT-5303, TVT-5304,
TVT-5305, TVT-5306
TruVision TVI Fixed Lens Turret Cameras
NTSC: TVT-4401
PAL: TVT-2401
Hole 2
TruVision TVI VF Motorized Lens Turret
Camera
NTSC: TVT-4402
PAL: TVT-2402
Hole 3
Double-gang box (electrical box)
TVD-BB3: TruVision dome back box
TVD-BB3A: TruVision dome angled back box
TVD-M2-WM: TruVision wall mount
TVD-CB3: Dome 3-inch cup base
Installation
To attach a turret camera to a double-gang box:
1. Install the turret adapter plate to the double-gang box by
inserting four C screws into holes 3 (see the Dimensions
figure for the location of the holes).
2 / 4 P/N 1073275-EN • REV A • ISS 06FEB17
2. Remove the camera body from the turret camera base.
Attach the base to the turret adapter plate by inserting the
B screws into holes 2 or B screws into holes 1. Refer to
the Supported equipment section.
3. Make the proper connections to the cable harness and
conceal the cables. Reattach the camera body to the base
and adjust the position of the lens.
To attach a turret camera to a TVD-BB3 dome back box:
1. Install the turret adapter plate to TVD-BB3 dome back box
by inserting four A screws into holes 3 (see the
Dimensions figure for the location of the holes).
2. Remove the camera body from the turret camera base.
Attach the base to the turret adapter plate by inserting the
B screws into holes 2 or B screws into holes 1. Refer to
the Supported equipment section.
3. Make the proper connections to the cable harness and
conceal the cables. Reattach the camera body to the base
and adjust the position of the lens.
To attach a turret camera to a TVD-BB3A dome angled
back box:
1. Install the turret adapter plate to the TVD-BB3A dome
angled back box by inserting four A screws into holes 3
(see the Dimensions figure for the location of the holes).
2. Remove the camera body from the turret camera base.
Attach the base to the turret adapter plate by inserting the
B screws into holes 2 or B screws into holes 1. Refer to
the Supported equipment section.
P/N 1073275-EN • REV A • ISS 06FEB17 3 / 4
3. Make the proper connections to the camera harness and
conceal the cables. Reattach the camera body to the base
and adjust the position of the lens.
To attach a turret camera to a TVD-M2-WM bracket:
1. Attach the turret adapter plate to TVD-M2-WM bracket by
inserting four A screws into holes 3 (see the Dimensions
figure for the location of the holes).
2. Remove the camera body from the turret camera base.
Attach the base to the turret adapter plate by inserting the
B screws into holes 2 or B screws into holes 1. Refer to
the Supported equipment section.
3. Make the proper connections to camera harness and
conceal the cables. Reattach the camera body to the base
and adjust the position of the lens.
To attach the turret camera to a TVD-CB3 cup base:
1. Attach the turret adapter plate to the TVD-CB3 cup base
by inserting four A screws into holes 3 (see the
Dimensions figure for the location of the holes).
2. Remove the camera body from the turret camera base.
Attach the base to the turret adapter plate by inserting the
B screws into holes 2 or B screws into holes 1. Refer to
the Supported equipment section.
3. Make the proper connections to the camera harness and
conceal the cables. Reattach the camera body to the base
and adjust the position of the lens.
Legal information
Trademarks and
patents
The trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Certification
Contact information
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.
/