AMERITRON ASP-200 User manual

Brand
AMERITRON
Model
ASP-200
Category
Video splitters
Type
User manual

AMERITRON ASP-200

The AMERITRON ASP-200 is a device used to connect a transceiver to two 50-ohm inputs. It has three SO-239 connectors, one for the transmitter, and two for HF amplifiers or any 50-ohm loads. The ASP-200 is commonly used with the Ameritron ACB-1000 to connect two amplifiers in parallel, doubling the power output compared to a single amplifier. It can handle up to 200 PEP or 100 watts continuous and measures 4”W x 4”D x 2”H.

To install the ASP-200, connect your transceiver to the "TRANSMITTER" connector.

AMERITRON ASP-200

The AMERITRON ASP-200 is a device used to connect a transceiver to two 50-ohm inputs. It has three SO-239 connectors, one for the transmitter, and two for HF amplifiers or any 50-ohm loads. The ASP-200 is commonly used with the Ameritron ACB-1000 to connect two amplifiers in parallel, doubling the power output compared to a single amplifier. It can handle up to 200 PEP or 100 watts continuous and measures 4”W x 4”D x 2”H.

To install the ASP-200, connect your transceiver to the "TRANSMITTER" connector.

ASP-200
The ASP-200 Splitter is design to connect a transceiver to two 50 ohm
inputs. The ASP has three SO-239 connectors. One for connecting to the
Transmitter (labeled Transmitter). The other two are for connecting to two
HF amplifier’s input or any 50 ohm loads (labeled Amp In 1 and Amp in 2).
The ASP-200 used with the Ameritron ACB-1000 will allow two amplifiers
to be connected in parallel. This will double your power compared to a
single amplifier.
The ASP-200 can handle up to 200 PEP or 100 watts continuous.
Measures: 4”W x 4”D x 2”H
Installation:
Connect your transceiver to the connector listed TRANSMITTER.
Note: When using the Ameritron ACB-1000 with this installation both
amplifiers must have the same output power.
Connect ASP’s AMP IN 1 to the RF Input of amplifier number 1. Connect
the RF Out of the same amplifier to the ACB-1000’s AMP OUT 1
Connector.
Connect ASP’s AMP IN 2 to the RF input of amplifier number 2. Connect
the RF Out of the same amplifier to the ACB-1000”s AMP OUT 2
connector.
Connect the relay control line from each amplifier to the transceiver. Note:
A “Y” cable maybe needed.
ASP-200
The ASP-200 Splitter is design to connect a transceiver to two 50 ohm
inputs. The ASP has three SO-239 connectors. One for connecting to the
Transmitter (labeled Transmitter). The other two are for connecting to two
HF amplifier’s input or any 50 ohm loads (labeled Amp In 1 and Amp in 2).
The ASP-200 used with the Ameritron ACB-1000 will allow two amplifiers
to be connected in parallel. This will double your power compared to a
single amplifier.
The ASP-200 can handle up to 200 PEP or 100 watts continuous.
Measures: 4”W x 4”D x 2”H
Installation:
Connect your transceiver to the connector listed TRANSMITTER.
Note: When using the Ameritron ACB-1000 with this installation both
amplifiers must have the same output power.
Connect ASP’s AMP IN 1 to the RF Input of amplifier number 1. Connect
the RF Out of the same amplifier to the ACB-1000’s AMP OUT 1
Connector.
Connect ASP’s AMP IN 2 to the RF input of amplifier number 2. Connect
the RF Out of the same amplifier to the ACB-1000”s AMP OUT 2
connector.
Connect the relay control line from each amplifier to the transceiver. Note:
A “Y” cable maybe needed.
Input
T1
T 2
In
R 7
10 0
LIMITED WARRANTY
Ameritron warrants to the original purchaser that this product shall be free from defects in
material or workmanship for one year from the date of original purchase.
During the warranty period, Ameritron will provide free of charge both parts and labor
necessary to correct defects in material or workmanship.
To obtain such warranty service, the original purchaser must:
Deliver the product to the Ameritron or ship the same in its original container or equivalent,
fully insured and with shipping charges prepaid.
Correct maintenance, repair, and use are important to obtain proper performance from this
product. Therefore, carefully read the Instruction Manual.
All implied warranties, if any, terminate one (1) year from the date of the original
purchase.
The foregoing constitutes Ameritron's entire obligation with respect to this product, and the
original purchaser and any user or owner shall have no remedy and no claim for incidental
or consequential damages. Some states do not allow limitations on how long an implied
warranty lasts or do not allow the exclusion or limitation of incidental or consequential
damage, so the above limitation and exclusion may not apply to you.
This warranty gives specific legal rights and you may also have other rights which vary
from state to state
Ameritron 116 Willow, Road Starkville, MS 39759 USA
662-323-8211 / www.ameritron.com
T1
T 2
In
R 7
10 0
Input
LIMITED WARRANTY
Ameritron warrants to the original purchaser that this product shall be free from defects in
material or workmanship for one year from the date of original purchase.
During the warranty period, Ameritron will provide free of charge both parts and labor
necessary to correct defects in material or workmanship.
To obtain such warranty service, the original purchaser must:
Deliver the product to the Ameritron or ship the same in its original container or equivalent,
fully insured and with shipping charges prepaid.
Correct maintenance, repair, and use are important to obtain proper performance from this
product. Therefore, carefully read the Instruction Manual.
All implied warranties, if any, terminate one (1) year from the date of the original
purchase.
The foregoing constitutes Ameritron's entire obligation with respect to this product, and the
original purchaser and any user or owner shall have no remedy and no claim for incidental
or consequential damages. Some states do not allow limitations on how long an implied
warranty lasts or do not allow the exclusion or limitation of incidental or consequential
damage, so the above limitation and exclusion may not apply to you.
This warranty gives specific legal rights and you may also have other rights which vary
from state to state
Ameritron 116 Willow, Road Starkville, MS 39759 USA
662-323-8211 / www.ameritron.com
  • Page 1 1
  • Page 2 2

AMERITRON ASP-200 User manual

Brand
AMERITRON
Model
ASP-200
Category
Video splitters
Type
User manual

AMERITRON ASP-200

The AMERITRON ASP-200 is a device used to connect a transceiver to two 50-ohm inputs. It has three SO-239 connectors, one for the transmitter, and two for HF amplifiers or any 50-ohm loads. The ASP-200 is commonly used with the Ameritron ACB-1000 to connect two amplifiers in parallel, doubling the power output compared to a single amplifier. It can handle up to 200 PEP or 100 watts continuous and measures 4”W x 4”D x 2”H.

To install the ASP-200, connect your transceiver to the "TRANSMITTER" connector.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents