Moxa NPort 5400 Series User manual

NPort 5000 Series User Manual

NPort 5000/5000A/IA5000/IA5000A/5000AI-M12 Series

Version 7.0, June 2023

www.moxa.com/products

NPort 5000 Series User Manual

The software described in this manual is furnished under a license agreement and may be used only in accordance

with the terms of that agreement.

Copyright Notice

Trademarks

The MOXA logo is a registered trademark of Moxa Inc.

All other trademarks or registered marks in this manual belong to their respective manufacturers.

Disclaimer

• Information in this document is subject to change without notice and does not represent a commitment

on the part of Moxa.

• Moxa provides this document as is, without warranty of any kind, either expressed or implied, including,

but not limited to, its particular purpose. Moxa reserves the right to make improvements and/or

changes to this manual, or to the products and/or the programs described in this manual, at any time.

• Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no

responsibility for its use, or for any infringements on the rights of third parties that may result from its

use.

• This product might include unintentional technical or typographical errors. Changes are periodically

made to the information herein to correct such errors, and these changes are incorporated into new

editions of the publication.

Technical Support Contact Information

www.moxa.com/support

Table of Contents

1. About This Manual ................................................................................................................................ 6

2. Getting Started ..................................................................................................................................... 7

Installing Your NPort Device Server .......................................................................................................... 7

Wiring Requirements ...................................................................................................................... 7

Connecting the Power ..................................................................................................................... 8

Grounding the NPort Device Server .................................................................................................. 8

Connecting to the Network .............................................................................................................. 9

Connecting to a Serial Device .......................................................................................................... 9

LED Indicators ............................................................................................................................... 9

Beeper Definition ......................................................................................................................... 11

RS-485 Port’s Adjustable Pull High/Low Resistor ............................................................................... 11

Windows Utility for the NPort ................................................................................................................ 11

Configuration by Web Console ............................................................................................................... 12

Opening Your Browser .................................................................................................................. 12

Quick Setup (excluding the NPort 5100, 5200, and IA5000 Series) ..................................................... 15

Export/Import (Excluding the NPort 5100, 5200, and IA5000 Series ................................................... 17

Basic Settings .............................................................................................................................. 19

Network Settings .......................................................................................................................... 22

Serial Settings ............................................................................................................................. 28

Operating Settings ....................................................................................................................... 31

Accessible IP Settings ................................................................................................................... 33

Firmware Upgrading Compatibility Check ................................................................................................ 34

Account Management ........................................................................................................................... 35

Notification Message ..................................................................................................................... 35

User Account ............................................................................................................................... 36

Password and Login Policy ............................................................................................................. 37

Auto Warning Settings .................................................................................................................. 38

Monitor ....................................................................................................................................... 43

System Log Settings ............................................................................................................................ 45

Change Password ......................................................................................................................... 46

Load Factory Default ..................................................................................................................... 47

Configuration by Telnet Console ............................................................................................................ 47

Configuration by Serial Console ............................................................................................................. 51

Serial Console (19200, n, 8, 1) ...................................................................................................... 51

Testing Your NPort ............................................................................................................................... 53

3. Cybersecurity Considerations ............................................................................................................. 54

Updating Firmware .............................................................................................................................. 54

Turn Off Unused Service and Ports ......................................................................................................... 54

Turn Off Moxa Service After Installation .......................................................................................... 54

Turn On Services That Are Necessary ............................................................................................. 54

Limited IP Access ................................................................................................................................. 55

Account and Password .......................................................................................................................... 55

System Log ......................................................................................................................................... 55

Testing the Security Environment .......................................................................................................... 55

4. Choosing the Proper Operation Mode ................................................................................................. 57

Overview ............................................................................................................................................ 57

Real COM Mode ................................................................................................................................... 57

RFC2217 Mode .................................................................................................................................... 58

TCP Server Mode ................................................................................................................................. 58

TCP Client Mode .................................................................................................................................. 59

UDP Mode ........................................................................................................................................... 59

Pair Connection Mode ........................................................................................................................... 59

Ethernet Modem Mode .......................................................................................................................... 59

Reverse Telnet Mode ............................................................................................................................ 60

PPP Mode ............................................................................................................................................ 60

Disabled Mode ..................................................................................................................................... 60

5. Advanced Operation Mode Settings .................................................................................................... 61

Overview ............................................................................................................................................ 61

List of Parameters ........................................................................................................................ 61

When to Make Adjustments ........................................................................................................... 62

Using Pair Connection Modes ................................................................................................................. 62

Parameter Summary ............................................................................................................................ 62

Connection Management Parameters .............................................................................................. 62

Data Packing Parameters .............................................................................................................. 64

Other Parameters ......................................................................................................................... 65

Web Console ....................................................................................................................................... 67

6. Installing Windows Driver .................................................................................................................. 91

7. Windows Utilities for NPort 5000 Models ........................................................................................... 92

Device Search Utility (DSU) .................................................................................................................. 92

Installing Device Search Utility ....................................................................................................... 92

Configuring by Device Search Utility (DSU) ...................................................................................... 92

Configuration by NPort Administrator Suite ........................................................................................... 101

Installing NPort Administrator ...................................................................................................... 101

Searching for Device Servers over a LAN ....................................................................................... 101

Unlock Your NPort ...................................................................................................................... 103

Configure .................................................................................................................................. 104

Upgrading the Firmware .............................................................................................................. 124

Export Configuration ................................................................................................................... 125

Import Configuration .................................................................................................................. 126

Monitor ..................................................................................................................................... 128

Port Monitor .............................................................................................................................. 131

COM Mapping ............................................................................................................................ 132

COM Grouping ........................................................................................................................... 137

IP Address Report ...................................................................................................................... 146

Configuring by NPort Windows Driver Manager ...................................................................................... 147

Using NPort Windows Driver Manager ........................................................................................... 148

Command Line Installation/Removal ............................................................................................. 156

Port Sniffer Wizard ............................................................................................................................. 159

8. Installing Linux Real TTY Driver ....................................................................................................... 168

Basic Procedures ............................................................................................................................... 168

Hardware Setup ................................................................................................................................ 168

Installing Linux Real TTY Driver Files .................................................................................................... 168

Mapping TTY Ports ............................................................................................................................. 169

Mapping tty ports automatically ................................................................................................... 169

Mapping tty ports manually ......................................................................................................... 169

Removing Mapped TTY Ports ............................................................................................................... 169

Removing Linux Driver Files ................................................................................................................ 170

9. Installing Linux Arm Driver .............................................................................................................. 171

Introduction ...................................................................................................................................... 171

Porting to the Moxa UC-Series—Arm-based Computer ............................................................................ 171

Build binaries on a general Arm platform ....................................................................................... 171

Cross-compiler and the Real TTY driver ......................................................................................... 172

Moxa cross-compiling interactive script ......................................................................................... 173

Manually build the Real TTY driver with a cross-compiler ................................................................. 173

Deploy cross-compiled binary to target ......................................................................................... 176

Porting to Raspberry Pi OS .................................................................................................................. 176

Porting to the Yocto Project on Raspberry Pi .......................................................................................... 177

Prerequisite ............................................................................................................................... 177

Create a Moxa layer for the Yocto Project ...................................................................................... 178

Install a Moxa layer into the Yocto Project ..................................................................................... 182

Deploy the Yocto image in Raspberry Pi ........................................................................................ 182

Start the Real TTY driver in Raspberry Pi ....................................................................................... 182

Set the default tty mapping to the Real TTY configuration ............................................................... 183

Troubleshooting ......................................................................................................................... 183

10. Installing macOS Driver .................................................................................................................... 184

Basic Procedures ............................................................................................................................... 184

Hardware Setup ................................................................................................................................ 184

Installing macOS TTY Driver Files ................................................................................................. 184

Mapping macOS TTY port .................................................................................................................... 187

Uninstalling the Driver ........................................................................................................................ 190

11. Installing WinCE Driver .................................................................................................................... 191

Overview .......................................................................................................................................... 191

Installing NPort CE Driver Manager ...................................................................................................... 191

Using NPort CE Driver Manager ........................................................................................................... 192

12. IP Serial LIB ..................................................................................................................................... 195

Overview .......................................................................................................................................... 195

What is IP Serial Library? ............................................................................................................ 195

Why Use IP Serial Library? .......................................................................................................... 195

How to Install IP Serial Library ..................................................................................................... 195

IP Serial LIB Function Groups .............................................................................................................. 196

Example Program .............................................................................................................................. 196

13. Android API Instructions .................................................................................................................. 197

Overview .......................................................................................................................................... 197

How to Start MxNPortAPI ............................................................................................................ 198

MxNPortAPI Function Groups ............................................................................................................... 199

Example Program .............................................................................................................................. 199

14. Introduction to LCM Display ............................................................................................................. 200

Basic Operation ................................................................................................................................. 200

Detailed Menu Options ....................................................................................................................... 200

A. Pinouts and Cable Wiring .................................................................................................................. 203

Port Pinout Diagrams ......................................................................................................................... 203

Ethernet Port Pinouts .................................................................................................................. 203

Serial Port Pinouts ...................................................................................................................... 203

Cable Wiring Diagrams ....................................................................................................................... 206

Ethernet Cables ......................................................................................................................... 206

Serial Cables ............................................................................................................................. 206

B. Adjustable Pull High/low Resistors for the RS-485 Port ................................................................... 214

C. Well-known Port Numbers ................................................................................................................ 224

D. SNMP Agents with MIB II & RS-232/422/485 Like Groups .............................................................. 226

E. Auto IP Report Protocol .................................................................................................................... 228

F. Compliance Notice ............................................................................................................................ 230

G. How to Become a Registered User of Moxa Website ......................................................................... 231

NPort 5000 Series User Manual

6

1. About This Manual

Read this user’s manual to learn how to configure and use your Moxa NPort device server. The following

products are covered by this manual:

NPort Family

Model Series

Introduction

NPort 5000

NPort 5110/5130/5150 Series

NPort 5210/5230/5232 Series

NPort 5410/5430/5450 Series

NPort 5610/5630/5650 Series

NPort 5610-8-DT/5650-8-DT Series

NPort 5610-8-DTL/5650-8-DTL Series

NPort 5000 Series device servers make

serial devices network-ready in an

instant. The different form factors of the

servers provide flexible options for users

to connect legacy devices to an IP-based

Ethernet LAN.

NPort 5000A

NPort 5110A/5130A/5150A Series

NPort 5210A/ 5230A/5250A Series

NPort 5150AI-M12/5250AI-M12/5450AI-M12

Series

NPort P5150A Series

The NPort 5000A device servers make

serial devices network-

ready in an instant

and give your PC software direct access

to serial devices from anywhere on the

network. The NPort 5000A device servers

are ultra-lean, rugged, and user-friendly,

making simple and reliable serial-to-

Ethernet solutions possible.

NPort

IA5000/IA5000A

NPort IA5150/IA5250 Series

NPort IA5150A/IA5250A/IA5450A Series

NPort IA device servers are an ideal

choice for establishing network access to

RS-232/422/485 serial devices, including

PLCs, sensors, meters, motors, drives,

barcode readers, and operator displays.

All models are housed in a compact,

rugged, DIN-rail mountable housing, and

come with redundant power inputs,

cascading Ethernet ports, and industrial-

grade certifications.

NPort 5000 Series User Manual

7

2. Getting Started

In this chapter, we explain how to install a Moxa NPort device server for the first time. There are four ways

to access the Moxa NPort’s configuration settings: Windows utility, web console, serial console, or Telnet

console.

NPort products support the following configuration options:

• Windows Utilities: NPort Administrator; Device Search Utility and Windows Driver Manager

• Web Console

• Quick Setup Wizard*

• Serial Console**

• Telnet Console

* Does not support 5100/5200/IA5000 series

** Only available for the NPort Series that has RS-232 interface.

Installing Your NPort Device Server

This section describes how to connect an NPort device server to your serial devices for the first time. We

cover Wiring Requirements, Connecting the Power, Grounding the NPort Device Server, Connecting to the

Network, Connecting to a Serial Device, and LED Indicators.

Wiring Requirements

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or wiring your NPort Device Server.

Wiring Caution!

Calculate the maximum current allowed in each power wire and common wire. Observe all electrical codes

dictating the maximum current allowed for each wire size. If the current goes above the allowed

maximum, the wiring could overheat, causing serious damage to your equipment.

Temperature Caution!

Please be cautious when handling the NPort device server. When plugged in, the NPort’s internal

components generate heat, and consequently, the casing may be too hot to the touch. When installed with

other components, make sure that there is at least a 2-cm clearance on all sides of the NPort device server

in order to allow proper heat dissipation.

You should observe:

• Use separate paths to route wiring for power and devices. If the power wiring and device wiring paths

must cross, make sure the wires are perpendicular at the intersection point.

NOTE

Do not run signal or communication wiring and power wiring in the same wire conduit. To avoid

interference, wires with different signal characteristics should be routed separately.

NPort 5000 Series User Manual

8

• You can use the type of signal transmitted through a wire to determine which wires should be kept

separate. The rule of thumb is that wires that share similar electrical characteristics can be bundled

together.

• Keep input wiring and output wiring separate.

• Where necessary, we strongly advised that you label wires to all devices in the system.

Connecting the Power

Connect the power line with the NPort’s power input. If the power is properly supplied, the “Ready” LED will

show a solid red color until the system is ready, at which time the “Ready” LED will change to a green color.

Grounding the NPort Device Server

Note: This section only applies if your NPort’s power input is on a terminal block.

Grounding and wire routing help limit the effects of noise caused by electromagnetic interference (EMI). Run

the ground connection from the ground screw to the grounding surface before connecting the devices.

WARNING

NPorts with a power terminal block are intended to be mounted to a well-grounded mounting surface, such

as a metal panel.

Type of Power Terminal Block

Shielded Ground (SG)

Applicable Products

The Shielded Ground (sometimes called

Protected Ground) contact is the left most

contact of the 7-pin power terminal block

connector when viewed from the angle

shown here. Connect the SG wire to an

appropriate grounded metal surface.

NPort IA5000 Series

The Shielded Ground (sometimes called

Protected Ground) contact is the left most

contact of the 8-contact power terminal

block connector when vi

ewed from the angle

shown here. Connect the SG wire to an

appropriate grounded metal surface.

NPort IA5000A Series

The Shielded Ground (sometimes called

Protected Ground) contact is the left most

contact of the 3-pin power terminal block

connector when viewed from the angle

shown here. Connect the SG wire to an

appropriate grounded metal surface.

NPort 5200/5400 Series

NPort 5200A Series

The Shielded Ground (sometimes called

Protected Ground) contact is the second

contact from the right of the 5-pin power

terminal block connector on the rear panel

of NPort 5600 VDC models. Connect the SG

wire to the earth ground.

NPort 5600 Series

NPort 5000 Series User Manual

9

Connecting to the Network

Connect one end of the Ethernet cable to the NPort’s 10/100M Ethernet port and the other end of the cable

to the Ethernet network. The NPort device server will show a valid connection to the Ethernet in the

following ways:

• The Ethernet LED maintains a solid green color when connected to a 100 Mbps Ethernet network.

• The Ethernet LED maintains a solid orange color when connected to a 10 Mbps Ethernet network.

• The Ethernet LED will flash when Ethernet packets are being transmitted or received.

ATTENTION

NPort IA5000/IA5000A/5600-8-DT Series of NPorts has two Ethernet ports that can create an open chain

of NPort IA5000/IA5000A/5600-8-DT device servers. Be careful not to connect the Ethernet ports of the

two device servers at the ends of the chain.

In other words, NPort IA5000/IA5000A/5600-8-DT Series of NPorts do NOT support closed chains.

Connecting to a Serial Device

Connect a serial data cable between the NPort and the serial device. Serial data cables must be purchased

separately. They are not provided with the NPort.

LED Indicators

NPort 5100/5100A/P5150A Series

LED Name

LED Color

LED Function

Ready

Red

Steady on:

Power is on, and the NPort is booting up.

Blinking:

Shows an IP conflict, or the DHCP or BOOTP server did not

respond properly.

Green

Steady on:

Power is on, and the NPort is functioning normally.

Blinking:

The device server has been located by NPort Administrator’s

Location function.

Off

Power is off, or a power error condition exists.

Link

Orange

The device is connected to a 10 Mbps Ethernet connection.

Green

The device is connected to a 100 Mbps Ethernet connection.

Off

The Ethernet cable is disconnected, or has a short.

Tx/Rx

Orange

The serial port is receiving data.

Green

The serial port is transmitting data.

Off

Data is NOT being transmitted or received through the serial port.

NPort 5200/5200A/5400 Series

LED Name

LED Color

LED Function

Ready

Red

Steady on:

Power is on, and the NPort is booting up.

Blinking:

Shows an IP conflict, or the DHCP or BOOTP server did not

respond properly.

Green

Steady on:

Power is on, and the NPort is functioning normally.

Blinking:

The device server has been located by NPort Administrator’s

Location function.

Off

Power is off, or a power error condition exists.

Link

(Ethernet)

Orange

The device is connected to a 10 Mbps Ethernet connection.

Green

The device is connected to a 100 Mbps Ethernet connection.

Off

The Ethernet cable is disconnected, or has a short.

P1, P2,

(P3, P4)

Orange

The serial port is receiving data.

Green

The serial port is transmitting data.

Off

Data is NOT being transmitted or received through the serial port.

NPort 5000 Series User Manual

10

NPort 5600 Series (Rackmount)

LED Name

LED Color

LED Function

Ready

Red

Steady on:

Power is on and the NPort is booting up.

Blinking:

Shows an IP conflict, or the DHCP or BOOTP server did not

respond properly.

Green

Steady on:

Power is on, and the NPort is functioning normally

Blinking:

The device server has been located by NPort Administrator’s

Location function.

Off

Power is off, or a power error condition exists.

Tx/Rx,

P1 to P16

Orange

The serial port is receiving data.

Green

The serial port is transmitting data.

Off

Data is NOT being transmitted or received through the serial port.

LAN

Green

The Ethernet port is connected, but data is NOT being transmitted.

Blinking

The Ethernet port is connected, and data is being transmitted.

Off

The Ethernet port is disconnected.

PWR

Green

Power cable is connected and provides electricity properly.

Off

Power cable is disconnected.

NPort 5600-8-DT/DTL Series

LED Name

LED Color

LED Function

PWR

Red

Power is on.

Off

Power is off.

Ready Green

Steady on:

The NPort is operational.

Blinking:

The NPort is responding to NPort Administrator’s Location

function, or the NPort is being reset to factory defaults.

Off

Power is off, or power error condition exists.

Fault

Red

Shows an IP conflict, or the DHCP or BOOTP server did not respond properly.

Off

No fault condition detected.

Off

Blinking:

Network is connected, data is being transmitted.

ETH 1, ETH2

Green

Steady on

Network is connected, no data is being transmitted.

Off

Blinking

Network is connected, data is being transmitted.

In Use

(P1 to P8)

Green

Serial port has been opened by server side software.

Off

Serial port is not currently opened by host side software.

Tx/Rx

(P1 to P8)

Green (Tx)

Serial device is transmitting data.

Orange(Rx)

Serial device is receiving data.

Off

No data is flowing to or from the serial port.

NPort 5000AI-M12 Series

LED Name

LED Color

LED Function

PWR

Green

Power is being supplied to the power input.

Ready

Red

Steady on:

Power is on, and the NPort is booting up.

Blinking:

Shows an IP conflict, or the DHCP or BOOTP server did not

respond properly.

Green

Steady on:

Power is on, and the NPort is functioning normally

Blinking:

The device server has been located by NPort Administrator’s

Location function.

Off

Power is off, or a power error condition exists.

10M, 100M

Orange

The device is connected to a 10 Mbps Ethernet connection.

Green

The device is connected to a 100 Mbps Ethernet connection.

Off

The Ethernet cable is disconnected, or has a short.

P1, P2, P3, P4

Orange

The serial port is receiving data.

Green

The serial port is transmitting data.

Off

Data is NOT being transmitted or received through the serial port.

NPort 5000 Series User Manual

11

NPort IA5000/IA5000A Series

LED Name

LED Color

LED Function

PWR1, PWR2

Red

Power is being supplied to power input PWR1, PWR2.

Ready

Red

Steady on:

Power is on, and the NPort IA is booting up.

Blinking:

Shows an IP conflict, the DHCP or BOOTP server did not respond

properly, or a relay output was triggered. When the above two

conditions occur at the same time, check the relay output first.

If after resolving the relay output and the Ready LED is still

blinking, then there is an IP conflict, or the DHCP or BOOTP

server did not respond properly.

Green

Steady on:

Power is on and the NPort IA is functioning normally.

Blinking:

The device server has been located by NPort Administrator’s

Location function.

Off

Power is off, or a power error condition exists.

E1, E2

Orange

The device is connected to a 10 Mbps Ethernet connection.

Green

The device is connected to a 100 Mbps Ethernet connection.

Off

The Ethernet cable is disconnected, or has a short.

P1, P2,

(P3, P4)

Orange

The serial port is receiving data.

Green

The serial port is transmitting data.

Off

Data is NOT being transmitted or received through the serial port.

FX* Orange

Steady on:

The fiber port is connected, but data is NOT being transmitted.

Blinking:

The fiber port is connected, and data is being transmitted.

*Only applies to NPort IA5000 fiber models.

Beeper Definition

Beeper Timing

Frequency (Length/Intervals/Times)

Definition

Startup

100 ms / 100 ms / 2

When the NPort is ready to run

Locating

100 ms / 900 ms / when user stops the

function

When the NPort is located by an

utility such as DSU

RS-485 Port’s Adjustable Pull High/Low Resistor

For some applications, you may need to use termination resistors to prevent the reflection of serial signals.

When using termination resistors, it is important to set the pull high/low resistors correctly so that the

electrical signal is not corrupted. Refer to Appendix B for detailed instructions on how to set the pull

high/low resistor values for different models.

Windows Utility for the NPort

Moxa provides a few types of software with the NPort 5000 Series:

• The Device Search Utility (also known as DSU) includes broadcast search for all the NPort 5000s

accessible over the network and basic configuration for a quick start.

• The NPort Administrator Suite is for COM mapping, a full set of configuration and monitoring tools. It

serves NPort 5000 Series only.

• The NPort Windows Driver Manger is for COM mapping of Real COM operation mode.

All utilities are available to download from Moxa’s website: https://www.moxa.com/en/support/product-

support/software-and-documentation, and select your product and look for the driver for your OS platform.

For more detailed information on how to use these useful utilities, refer to Chapter 7.

You may also use the web console, serial console, or Telnet to configure the device server. Refer to the

section Configuration by Web Console, Configuration by Serial Console, and Configuration by Telnet Console

for additional information on using these consoles.

NPort 5000 Series User Manual

12

Configuration by Web Console

The Web Console is the most user-friendly way to configure NPort products. In this section, we cover a

device server’s general settings.

Opening Your Browser

1. Open your browser with the cookie functionality enabled. (To enable your browser for cookies, right-

click on your desktop’s Internet Explorer icon, select Properties, click on the Security tab, and then

select the three Enable options as shown in the figure below.)

2. Type 192.168.127.254 in the Address input box (use the correct IP address if different from the

default), and then press Enter.

3. For the overall NPort 5000 Series, you will be prompted to enter the username and password to access

the NPort web console. Before configuring the NPort, you will need to unlock it first. Right-click the unit

in the Configuration screen and select Unlock in the pop-up menu. The default username and password

are admin and moxa, respectively. For the NPort 5100, 5200, and IA5000 Series, only the password is

required to log in.

NPort 5000 Series User Manual

13

Web Interface for the NPort 5100, 5200, and IA5000 Series Only

Web Interface for the Overall NPort 5000 Series

ATTENTION

If you use other web browsers, remember to enable the functions to “allow cookies that are stored on your

computer” or “allow per-session cookies.” NPort device servers use cookies only for “password”

transmissions.

NPort 5000 Series User Manual

14

The NPort home page will open. On this page, you can see a brief description of the Web Console’s function

groups.

Web Interface for the NPort 5100, 5200, and IA5000 Series Only

Web Interface for the Overall NPort 5000 Series

ATTENTION

If you can’t remember the password, the ONLY way to configure the NPort is to load factory defaults by

using the Reset button near the NPort’s Ethernet port.

Remember to use NPort Administrator (for NPort 5000 and the NPort IA5000 Series) to export the

configuration file when you have finished the configuration. After using the Reset button to load factory

defaults, your configuration can be easily reloaded into the NPort by using the NPort Administrator Import

function. Refer to Chapter 5 for details about using the Export and Import functions.

NPort 5000 Series User Manual

15

Quick Setup (excluding the NPort 5100, 5200, and IA5000

Series)

Quick Setup streamlines configuration of your NPort into three basic and quick steps that cover the most

commonly used settings. While in Quick Setup, you may click the Back button at any time to return to the

previous step, or click the Cancel button to reverse all settings. For more detailed settings, refer to the

Basic Settings, Network Settings, Serial Settings, and Operating Settings sections later in this

chapter.

Step 1/3

In Step 1/3, you must assign a valid IP address to the NPort before it will work in your network

environment. Your network system administrator should provide you with an IP address and related settings

for your network. In addition, the server name field is a useful way to specify the location or application of

different NPort units.

Step 2/3

In Step 2/3, you must specify which operation mode you will use. If your operation mode is not Real COM,

TCP Server, TCP Client, or UDP mode, click Cancel, return to the main menu, and choose Operating

Settings to select the correct settings.

NPort 5000 Series User Manual

16

Step 3/3

In Step 3/3, change the Serial Settings.

Finish Settings

Review your settings on the Finish Settings page to confirm that they are correct and then click the

Save/Restart button to restart the device with the new settings.

NOTE

If you change the IP address, you cannot use the Home button to return to the home page.

NPort 5000 Series User Manual

17

Export/Import (Excluding the NPort 5100, 5200, and IA5000

Series)

Export/Import allows you to back up and recover your settings.

The exported configuration file can be encrypted for security with a user-specified export password (the

default password is moxa), which you may assign in Pre-shared Key. Click Download to write all

configuration data to a fixed file name: <Servername>.txt.

To import the configuration file, you will need to be sure that the pre-shared key stored in the system is the

same as the configuration file (which is assigned when exporting the configuration file) in order to

successfully import the configuration file.

NPort 5000 Series User Manual

18

If the firmware is not up to the version below, you many need to key in the password manually.

NPort 5100A Series Firmware v1.5

NPort 5200A Series Firmware v1.5

NPort 5150AI Series Firmware v1.4

NPort 5250AI Series Firmware v1.4

NPort 5450AI Series Firmware v1.4

NPort 5600 Series Firmware v3.9

NPort 5600 DT Series Firmware v2.6

NPort 5600 DTL Series Firmware v1.5

NPort IA5150A Series Firmware v1.4

NPort IA5450A Series Firmware v1.6

NOTE

The configuration encrypting function is not available in the NPort 5100, NPort 5200, and NPort IA5000

Series.

Refer to the table below for the firmware versions that support the encrypted configuration files in the Web

Console.

Model Name

Firmware version supporting encrypted configuration files.

NPort 5100A Series

Firmware v1.3 and up

NPort 5200A Series

Firmware v1.3 and up

NPort 5x50AI-M12 Series

Firmware v1.2 and up

NPort IA5150A, NPort IA5250A

Firmware v1.3 and up

NPort IA5450A

Firmware v1.4 and up

NPort 5000 Series User Manual

19

Basic Settings

Web Interface for the NPort 5100, 5200, and IA5000 Series Only

Web Interface for the Overall NPort Series

NPort 5000 Series User Manual

20

Web Interface for the NPort 5000AI-M12 Series Only

NOTE

The NPort 5100/5100A does not support Time Settings.

Parameter

Setting

Factory Default

Description

Necessity

Server name 1 to 39 characters

NP[model

name]_[Serial

No.]

This option is useful for specifying

the location or application of

different NPorts.

Optional

Time zone

User selectable time zone

Not available in NPort

5100/5100A/5200/5200A

Series

GMT (Greenwich

Mean Time) N/A Required

Local time

User adjustable time

(1900/1/1-2037/12/31)

Not available in NPort

5100/5100A Series

GMT (Greenwich

Mean Time)

Click the Modify button to open

the change time settings window

to input the correct local time.

Required

Time server

IP or Domain address

(only available in

2/4/8/16 ports models)

E.g., 192.168.1.1 or

time.stdtime.gov.tw or

time.nist.gov

None

NPorts use SNTP (RFC-1769) for

auto time calibration. Input the

correct Time server

IP address or

domain name. Once the NPort is

configured with the correct Time

server address, the NPort will

request time information from the

Time server every 10 minutes.

Optional

Daylight

saving

Setting 1: “Start Date:

Month, Week, Day, Hour”

None

The NPort can offset the system

time to the values you have set in

these settings.

(This feature only applies to the

NPort 5000AI-M12 Series.)

Setting 2: “End Date:

Month, Week, Day, Hour”

Setting 3: “Offset: hours”

htpp console

Enable or Disable

Disable

The options that are disabled by

default—http Console, Telnet

Console, and Serial Console—are

for security reasons. In some

Required

https console

Enable or Disable

Enable

Required

TLS v1.0/v1.1

for HTTPS

console

Enable or Disable Disable Required

Page is loading ...

Moxa NPort 5400 Series User manual

Moxa NPort 5400 Series User manual

Related papers

Other documents