Gigabyte W42G-P08R Installation guide

Type
Installation guide

Gigabyte W42G-P08R is a slide rails and rack assembly designed for mounting a W42G-P08R device into a rack. The assembly consists of two slide rails that attach to the rack and a front section that attaches to the device. The front section can be pulled out to allow access to the device, and then pushed back into the rack when not in use. The assembly also includes a latch that locks the front section in place when it is inserted into the rack. This assembly is ideal for mounting a device in a rack where space is limited or where the device needs to be easily accessible.

Gigabyte W42G-P08R is a slide rails and rack assembly designed for mounting a W42G-P08R device into a rack. The assembly consists of two slide rails that attach to the rack and a front section that attaches to the device. The front section can be pulled out to allow access to the device, and then pushed back into the rack when not in use. The assembly also includes a latch that locks the front section in place when it is inserted into the rack. This assembly is ideal for mounting a device in a rack where space is limited or where the device needs to be easily accessible.

GS-W42G-P08R
Slide Rails and Rack Installation Instructions
v
Position the front section against the W42G-P08R, and make sure the mounting holes on the front section are aligned with the locating pins on the
side of the W42G-P08R. Assemble the front section onto the W42G-P08R and pull back to lock on. (NOTE: Make sure the below xed bracket is
locked on.) Do the same for the other slide.
x After withdrawing the front section, push back the middle section into the slide rail assembly. Push the latch and push back the middle section into the
slide rail assembly.
u
Remove the side cover. Push the blue latch and push forward the side cover to remove it.
u Unpack the slide rail assembly. v Pull the slide rail assembly
until it reaches stop.
w
Push the latch between the front and middle section of the rail assembly,
then simultaneously withdraw the front section from slide rail assembly.
1Preparing the Slide
Rail Assembly
2Installing the Front
Section of the Slide
Rail onto the W42G-
P08R
Latch on the middle section
GS-W42G-P08R
Slide Rails and Rack Installation Instructions
v 
The front side and rear side assembly methods are the same. Attach the mounting bracket to the rack posts. Then lock on and push
down. Do the same for the other slide.
u
Pull out the slide rail assembly
on your rack until it stops.
u
Position the slide rail assembly in your rack and attach the mounting bracket to the rack posts. Then lock on and push down.
4Installing the W42G-
P08R onto the Rack
3Attaching the Slide
Rail Assemblies to
the Rack
v Align the front section of the
W42G-P08R with the rail
assembly and insert it.
(NOTE: You should insert the left
and right slides simultaneously
to prevent any stuck during the
insert process.)
w Installation completed.
GS-W42G-P08R
Slide Rails and Rack Installation Instructions
u
Push the latch on middle section of both sides and push the W42G-P08R back into rack to complete.
5Sliding the W42G-
P08R Back into the
Rack
  • Page 1 1
  • Page 2 2
  • Page 3 3

Gigabyte W42G-P08R Installation guide

Type
Installation guide

Gigabyte W42G-P08R is a slide rails and rack assembly designed for mounting a W42G-P08R device into a rack. The assembly consists of two slide rails that attach to the rack and a front section that attaches to the device. The front section can be pulled out to allow access to the device, and then pushed back into the rack when not in use. The assembly also includes a latch that locks the front section in place when it is inserted into the rack. This assembly is ideal for mounting a device in a rack where space is limited or where the device needs to be easily accessible.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI