12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectier Energy Transfer Hinge
Switch
EU (Fail Secure)
e)
Bridge
Rectifier
Wire Transfer Hinge
Bridge
Rectifier
Plug
3/8 Wire Raceway
Mortise
Lock
Pocket
Mortise
Lock
Pocket
Mortise
Lock
Pocket
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectier Energy Transfer Hinge
Switch
EU (Fail Secure)
EU (Fail Secure)
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectier Energy Transfer Hinge
Switch
EL (Fail Safe)
EL (Fail Safe)
Mortise
Lock
Pocket
3/8 Wire Raceway
ETH Hinge Pocket
Bridge
Rectifier
Plug
Mortise
Lock
Pocket
Mortise
Lock
Pocket
3/8 Wire Raceway
ETH Hinge Pocket
Wire Transfer Hinge
3/8 Wire Raceway
Mortise
Lock
Pocket
Bridge
Rectifier
Plug
Mortise
Lock
Pocket
ETH Hinge Pocket
Bridge
Rectifier
Wire Transfer Hinge
Mortise
Lock
Pocket
1.. The door must be machined with a 3/8” wire raceway mortise
lock pocket & prepped for an energy transfer hinge.
Note: Make sure the mortise pocket is free of debris
Solenoids
Volt Current Coil Resistance
350mA 69 Ohms +/- 10%
700mA 18 Ohms +/- 10%
24VAC/DC
12VAC/DC
Switches
REX
Green - Common (C)
Blue - Normally Open (NO)
Gray - Normally Closed (NC)
LBM
Green/Black - Common (C)
Blue/Black - Normally Open (NO)
Gray/Black - Normally Closed (NC)
DPS
Green/Red - Common (C)
Blue/Red - Normally Open (NO)
(NC) Gray/Red - Normally Closed
trim will unlock. When power is
will lock. When power is removed,
Legends of Terms
EU: (Fail Secure) When power is applied, the outside
removed, the outside trim is locked.
EL: (Fail Safe) When power is applied, the outside trim
the outside trim is unlocked.
REX: (Request to Exit Switch) Monitors the inside handle.
*LBM: (Latchbolt Monitor Switch) Monitors the position of the latchbolt.
*DPS: (Door Position Switch) Monitors the door via the anti pick (deadlatch).
*
Installation of Electrified Mortise Lock: Electrical Specifications:
Mortise
Lock
Pocket
3/8 Wire Raceway
ETH Hinge Pocket
Wire Transfer Hinge
3/8 Wire Raceway
Mortise
Lock
Pocket
ge through the 3/8” raceway starting at the ETH hinge2.. Run the wires from the ETH hin
and exiting into the mortise pocket.
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectier Energy Transfer Hinge
Switch
EU (Fail Secure)
EU (Fail Secure)
12VAC/DC
24VAC/DC
or
Power
Supply
Bridge Rectier Energy Transfer Hinge
Switch
EL (Fail Safe)
EL (Fail Safe)
3.3.. ScreScrew the ETH hinw the ETH hinge to the door. At this time DO NOT connect the hinge
wires on the jamb side to the wiresjamb side to the wires coming from the power supply.
4.. Connect the wires exiting the mortise pocket to the Bridge Rectifier (included)
55.. Connect the Bridge Rectifier to the plug exiting the mortise chassis
Bridge
Rectifier
Mortise
Lock
Pocket
Bridge
Rectifier
Plug
Mortise
Lock
Pocket
6.. Carefully slip the connected mortise lock chassis into the mortise pocket paying close
attention not to pinch any wires.
7.. Mount the chassis into the door frame
8.. Connect the wires from t8. Con ect the wires from the power supply at the ETH hinge on the jamb side.
n
Connect the hinge to the jamb.
MC7000 Mortise Locks
Electrified Installation
Engineered Beautifully
/
