Uolfin 5106304 is a ceiling lamp compatible with Type A bulbs up to 60 watts each. Installation requires basic tools and electrical knowledge. It has an adjustable height and comes with all the necessary hardware for mounting. The lamp can be used in various settings, including living rooms, dining rooms, and bedrooms. Ensure to follow the safety guidelines during installation, including turning off the power before starting the process.
Uolfin 5106304 is a ceiling lamp compatible with Type A bulbs up to 60 watts each. Installation requires basic tools and electrical knowledge. It has an adjustable height and comes with all the necessary hardware for mounting. The lamp can be used in various settings, including living rooms, dining rooms, and bedrooms. Ensure to follow the safety guidelines during installation, including turning off the power before starting the process.
+1 850 296 2377 Working hours : Mon - Fri 9:00 - 16:00 EST [email protected]
Page: - 1 - / 4
Item Number: 5106304
WARNING (To reduce the risk of fire, electric shock, or personal injury):
1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
»
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
»
Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps
between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type A,Max 60W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot
quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It
must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED
(NOT INCLUDED):
Before starting assembly and installation please prepare the needed
tools as below picture
Ladder Philips Head or Flat
Blade Screwdriver Electrical Tape Pilers Wire Cutter/Stripper
+1 850 296 2377 Working hours : Mon - Fri 9:00 - 16:00 EST [email protected]
Page: - 2 - / 4
PARTS TYPE & QTY INCLUDING:
(C) Mounting plate (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Swivel joint (1)
(G) Knob nut (2)
(H) Tube
(I) Iron frame (1)
(J) Screw (3)
(K) Cover (1)
(L) Glass shade (1)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
1. Carefully remove the fixture from the carton and check that all parts and accessories are
included as shown in the above illustration.
2. Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity
until the work is done.
Unscrew knob nuts (G) from canopy (E) then remove
mounting plate (C).
ACCESSORIES & QTY ENCLOSED:
(A) Plastic wire connector (3)
(B) Mounting screw (2)
»
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
»
Place the wall switch in the “OFF” position.
3 »
+1 850 296 2377 Working hours : Mon - Fri 9:00 - 16:00 EST [email protected]
Page: - 3 - / 4
1) According to your desired hanging height to choose and
use tubes (H).
Then pass the fixture wires through the chosen tubes (H),
swivel joint (F) and canopy (E).
2) Be sure that all the threaded pipes are tightened, then
screw the chosen tubes (H) onto swivel joint (F) and the
top of iron frame (I).
Hand tighten till snug.
Attach mounting plate (C) to the outlet box with mounting
screws (B).
Make wire connections
Connect wires as below wires connection shown.
PLEASE NOTE THAT GROUND WIRE IS BARE COPPER
WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
4 »
5 »
6 »
Connect Black or
Red Supply Wire to: Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black without
tracer Clear, Brown, Gold or Black with
tracer
Insulated wire(other than green)
with copper conductor Insulated wire(other than green)
with silver conductor
* Note: When parallel wires (SPT I&
SPT ll) are used. The neutral wire is
square shaped or ridged and the
other wire will be round in shape or
smooth (see illus.)
OUTLET BOX
GROUND
DIMPLES
GREEN GROUND
SCREW
CUPPED
WASHER
FIXTURE
GROUND
Neutral Wire
GREEN GROUND
SCREW
OUTLET BOX
GROUND
FIXTURE
GROUND
Connect ground wires according to the below chart Connect wires according to the below chart
+1 850 296 2377 Working hours : Mon - Fri 9:00 - 16:00 EST [email protected]
Page: - 4 - / 4
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector
with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all
wires into the outlet box.
Raise canopy (E) to the ceiling and secure canopy (E) in
place by tightening knob nuts (G) onto the pre-assembled
screws in mounting plate (C).
1) Install the bulb (not included) (Please do not exceed the
maximum wattage recommended on the socket.)
2) Place cover (K) on glass shade (L).
3) Remove screws (J) from iron frame (I), then carefully
align glass shade (L), cover (K) and iron frame (I).
4) Secure them with screws (J).
9. Check everything is already installed properly, then you could turn on the light. Enjoy!
7 »
Note: canopy (E) should be snug against the ceiling
and knob nuts (G).
If not, adjust the threaded length on mounting plate
assembly (C):
• Unscrew the pre-assembled hex nuts;
• Screw the pre-assembled screws in or out of
mounting plate (C);
• When the secure length is achieved, tighten the hex
nuts and back to step 7.
8 »
ORDERING PARTS
Keep this sheet for future reference in case you need
to order replacement parts. All parts for this fixture can
be ordered from the place of purchase. Be sure to use
exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass
with a mild cleaner (such as mild and non-abrasive
soap). Do not use abrasive materials such as scouring
pads or powders, steel wool or abrasive paper.
-
1
-
2
-
3
-
4
Uolfin 5106304 is a ceiling lamp compatible with Type A bulbs up to 60 watts each. Installation requires basic tools and electrical knowledge. It has an adjustable height and comes with all the necessary hardware for mounting. The lamp can be used in various settings, including living rooms, dining rooms, and bedrooms. Ensure to follow the safety guidelines during installation, including turning off the power before starting the process.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Uolfin 4806474 User manual
-
Uolfin A04937 Installation guide
-
Uolfin A04787W4 User manual
-
Uolfin A04787W3 User manual
-
-
Uolfin NV6BU3-LWS232W3-F8 Installation guide
-
Uolfin A04912 User manual
-
-
Uolfin A04310 Installation guide
-
Uolfin 7NQ32I-LWS23968-L7 User manual
Other documents
-
Lowe s Uolfin A04803 User manual
-
Uolfin Home 628P8MU2IJN52W1 User manual
-
LNC A05152A User manual
-
Lowe s 5106331 User manual
-
Lowes 5069596 User manual
-
LNC A04085 Gold Cube Starburst Chandelier User manual
-
Ralph Lauren RL 2530 Owner's manual
-
Lowes 4978229 User manual
-
CANARMNA ICH2012B04BKG15 User manual
-
LNC YUMNR2LWS4911F8 Installation guide
