Bestop TrailMax 9333 Vinyl Installation Instructions Manual

Brand: Bestop

Model: TrailMax 9333 Vinyl

Category: Car kits

Type: Installation Instructions Manual

This manual is also suitable for

TrailMax 39343 Cloth

39333/39343 pg 1

1201 Rev. B

TrailMax™ Fold and Tumble

Rear Seat

Installation Instructions

Before you begin installing this seat, please read all installa-

tion instructions and warnings thoroughly.

This seat is designed to be used on the model vehicles

described above. Use of this seat on any other vehicle or

failure to install this seat properly may result in an improperly

mounted seat and could result in unexpected movement of

the seat and loss of control of the vehicle, thereby placing the

occupants of the vehicle and others in a potentially danger-

ous situation.

This seat system is intended to be used with seat belts at all

times. Do not rely on the seat to maintain the seating position

of occupants, in the event of an accident.

WEAR SEAT BELTS AT ALL TIMES

Read and follow, precisely, all installation instructions pro-

vided when installing this product. Failure to do so may result

in a poor fit and could place occupants of the vehicle in a

potentially dangerous situation.

WARNING

For: All Jeep

CJ5s, CJ7s and Wranglers 1955-1995 Part Number: 39333 Vinyl

39343 Cloth

Jeep

is a registered trademark of Chrysler and

Bestop is not affiliated with Chrysler Corporation.

NOTE: In 1985 and older vehicles, the seat

installation will be easier with two people.

39333/39343 pg 2

1201 Rev. B

3/8-16 x 1 1/4" Bolt, Qty - 4

Flat Washer, Qty - 2

Plastic Flat Washer,

Qty - 2

M8-1.25 x 35mm Bolt, Qty - 8

1/4-20 x 1 1/4" Bolt, Qty - 4

5/16-18 x 1 1/4" Bolt, Qty - 4

Parts List and Hardware Identification

Seat, Qty - 1

Installation Instruction

Manual, Qty - 1

39333/39343 pg 1

1298 Rev. 1

TrailMax™ Fold and Tumble

Rear Seat

Installation Instructions

Before you begin installing this seat, please read all installa-

tion instructions and warnings thoroughly.

This seat is designed to be used on the model vehicles

described above. Use of this seat on any other vehicle or

failure to install this seat properly may result in an improperly

mounted seat and could result in unexpected movement of

the seat and loss of control of the vehicle, thereby placing the

occupants of the vehicle and others in a potentially danger-

ous situation.

This seat system is intended to be used with seat belts at all

times. Do not rely on the seat to maintain the seating position

of occupants, in the event of an accident.

WEAR SEAT BELTS AT ALL TIMES

Read and follow, precisely, all installation instructions pro-

vided when installing top. Failure to do so may result in a poor

fitting top and could place occupants of the vehicle in a

potentially dangerous situation.

WARNING

For: All Jeep

CJ5s, CJ7s and Wranglers 1955-1995 Part Number: 39333 Vinyl

39343 Cloth

Jeep

is a registered trademark of Chrysler and

Bestop is not affiliated with Chrysler Corporation.

NOTE: In 1985 and older vehicles, the seat

installation will be easier with two people.

Tools Needed

Adjustable Wrench or

9/16" Wrench

7/16" Wrench

1/2" Wrench (older models)

10mm Wrench (older models)

Safety Glasses

1985 or Earlier Vehicles

25/64" Drill Bit

7/16" Drill Bit (older models)

Lock Down

Bracket, Lt,

Qty - 1

Floor Mounting

Brackets, Qty - 2

Cotter Pin, Qty - 2

Tapping Plate, Qty - 4

Lock Down

Bracket, Rt,

Qty - 1

Note: Use only the Bestop hardware

provided in the kit.

M8-1.25 Hex

Nut Qty - 8

39333/39343 pg 3

1201 Rev. B

Seat Installation

Caution

Note: Before beginning the seat installation, set the

parking brake, place the vehicle in gear or park and

chock the wheels to reduce the risk of the vehicle

unexpectedly moving, which could result in seri-

ous injury.

Rear of Vehicle

Floor Mounting

Brackets

Front

Loop toward

front

Floor Mounting Bracket -

Place over existing holes

3/8-16 x 1 1/4" Bolts

Step One

Floor Mounting Bracket Installation

Locate the Floor Mounting Bracket mounting holes on the floor of

the vehicle behind the front seat risers. Align the Floor Mounting

Brackets over the mounting holes with the loop on the bracket

positioned towards the front of the vehicle. Insert two (2) 3/8-16 x

1 1/4" Bolts in each bracket. Loosely tighten the bolts using an

adjustable wrench or 9/16" wrench.

1986 and Newer Vehicles

WARNING

If your vehicle has carpet covering the floor, cut the carpet so that the Floor Mounting Brackets are installed flush on the metal floor. If the Floor Mounting

Brackets are not flush mounted, the seatback may not lock in place, which could result in serious injury to you and others.

39333/39343 pg 4

1201 Rev. B

Step One

Floor Mounting Bracket Installation

Orient the Seat, with the Legs on the bottom of the seat facing the rear of

the vehicle. Fold the Seat back down into the closed position.

Attach the two (2) Floor Mounting Brackets to the bottom of the seat by

sliding the pins of the Floor Mounting Brackets into the holes of the

brackets on the bottom of the seat. Install Cotter Pins through the small

hole in the Floor Mounting Bracket pin of the left and right Floor

Mounting Brackets. The loop on the Floor Mounting Bracket is to face the

front of the vehicle.

Set the Seat in the rear of the vehicle. Open the Seat, and with the seat

back in the raised position center the Seat from side to side and in the

desired position from front to rear.

Once the Seat is in the desired position lower the seat back and "tumble"

the Seat forward, maintaining the Floor Mounting Brackets in position.

Using the Floor Mounting Brackets as templates, mark hole locations of

the Floor Mounting Brackets. Remove the seat. Center punch and drill a

25/64" hole at each mark. Remove the Floor Mounting Brackets from the

seat.

Align the Floor Mounting Brackets over the drilled holes with the loops

on the Mounting Bracket positioned toward the front of the vehicle. From

underneath the vehicle, align the tapping plates and M8-1.25 Hex Nuts

over the drilled holes and hold them in place. Insert two (2) M8-1.25 x

35mm Bolts with two (2) Flat Washers through each Mounting Bracket.

Loosely tighten the bolts using an adjustable wrench or 10mm wrench.

1985 and Older Vehicles

WARNING

If your vehicle has carpet covering the floor, cut the carpet so that the Floor Mounting Brackets are installed flush on the metal floor. If the Floor Mounting

Brackets are not flush mounted, the seatback may not lock in place, which could result in serious injury to you and others.

Rear of Vehicle

Front

Loop toward

front

Tapping Plate -

under floor

Floor Mounting

Bracket

Seat

Cotter Pin

M8-1.25 x 35mm Bolts

Floor Mounting

Brackets

Slide Brackets on

Seat over Pins on

Floor Mounting

Brackets

Floor Mounting

Bracket

Flat Washers

M8-1.25 Hex Nuts -

under floor

39333/39343 pg 5

1201 Rev. B

WARNING

Rear of Vehicle

Seat

Seat Legs

Slide Brackets on

Seat over Pins on

Floor Mounting

Brackets

Seat

Cotter Pin

Failure to install the Cotter Pin may result in the seat moving off the Front Brackets which could result in serious injury to you and others.

Floor Mounting

Bracket

Step Two

Seat Installation

Orient the Seat, with the Legs on the bottom of the seat facing

the rear of the vehicle. Fold the Seat back down into the closed

position. Place Seat in the vehicle.

Slide the Seat toward the front of the vehicle. Align the holes of

the brackets, on the bottom of the seat cushion, with the pins

of the Floor Mounting Bracket. Slide the bracket holes over the

pins on the Floor Mounting Brackets. Slide a Plastic Flat

Washer over the pin and install a Cotter Pin through the holes

in the pin of the Left and Right Floor Mounting Bracket.

Plastic Flat

Washer

Slide Brackets on

Seat over Pins on

Floor Mounting

Brackets

Adjust the height of the Adjustable Seat Legs to assure the seat back locks securely into the Lock Down Brackets. If the Seat does not lock in place, it may

tilt forward unexpectedly which could result in serious injury to you and others.

WARNING

Note: If replacing a factory seat, please remove all factory hardware and replace with Bestop hardware from the enclosed kit.

Rear of Vehicle

Lock Down

Bracket

1986 and Newer Vehicles

Step Three

Lock Down Bracket Installation

Place the bottom of the seat down on the floor of the vehicle. Raise the seat back

into the sitting position. Locate the Lock Pin on the seat hinge and place a Lock

Down Bracket over the holes in the wheel well. Orient the Left and Right Lock

Down Brackets with the opening towards the top and the rear of the vehicle. Install

the appropriate Lock Down Bracket on each side of the vehicle using two 1/4-20 x

1 1/4" Bolts for model years 1986 - 1991 or 5/16-18 x 1 1/4" Bolts for model years

1992 - 1995. Loosely tighten the bolts using an adjustable wrench or 1/2" wrench

for 1986 - 1991 vehicles, or a 7/16" wrench for 1992 - 1995 vehicles.

Adjust the seat height to make sure the Seat locks into the Lock Down Brackets.

Tighten all eight (8) of the previously installed bolts with an adjustable wrench or

1/2" wrench for 1986 - 1991 vehicles, or a 7/16" wrench for 1992 - 1995 vehicles.

Seat Back

Lock Down

Bracket

Lock Pin

1/4-20 x 1 1/4" Bolts or

5/16-18 x 1 1/2" Bolts

Adjust height of the Seat Leg

to make sure seat locks

securely into Lock Down

Bracket

39333/39343 pg 6

1201 Rev. B

WARNING

Adjust the height of the Adjustable Seat Legs to assure the seat back locks securely into the Lock Down Brackets. If the Seat does not lock in place, it may tilt forward

unexpectedly which could result in serious injury to you and others.

Rear of Vehicle

Seat Back

Lock Down

Bracket

Tapping

Plate

Wheel Well

Step Three

Lock Down Bracket Installation

Lower the Seat onto the floor of the vehicle. Raise the Seat Back into the sitting

position. Locate the Lock Pin on the Seat Hinge

Orient the Left and Right Lock Down Brackets with the opening towards the top

and the rear of the vehicle. Place a Lock Down Bracket over the Lock Pin. The

bracket should be at a 10 degree angle to the floor with the bottom of the bracket

tilted toward the rear (the bottom hole should be 3/4" rearward of the top hole).

Use the Lock Down Bracket as a template. Mark the locations of the holes in the

bracket. Center punch the locations and drill a 21/64" hole at each mark.

While one person installs a Lock Down Bracket inside of the vehicle, using two

M8-1.25 x 35mm Bolts a second person places a Tapping Plate and two M8-1.25

Hex Nuts over the holes from under the wheel well. Loosely tighten the bolts

using an adjustable wrench or 10mm wrench.

This procedure is repeated for the other side of the vehicle.

Adjust the seat height to make sure the seat locks into the Lock Down Brackets.

Tighten all eight (8) of the previously installed bolts and nuts with an adjustable

wrench or 10mm wrench.

Lock Down

Bracket

Adjust height to make sure

seat locks securely into Lock

Down Bracket

Lock Down

Bracket

Lock

1985 and Older Vehicles

3/4"

(bottom hole

rearward of top

hole)

Tapping Plate -

under wheel well

M8-1.25 x 35mm Bolt

M8-1.25 x 35mm

Bolts

Note: If replacing a factory seat, please remove all factory hardware and replace with Bestop hardware from the enclosed kit.

M8-1.25 Hex Nuts -

under wheel well

39333/39343 pg 7

1201 Rev. B

Care of your Bestop Seat

Your seat is made of the finest materials available. To keep it looking new and for the

maximum possible wear, it will need periodic cleaning.

Washing: The seat fabric should be washed often using a mild detergent, warm water

and a soft bristle brush. Rinse with clear water to remove all traces of soap.

LIMITED WARRANTY

We warrant our product to be free from defects in material and workmanship, for terms specified below, provided there has been normal use and proper maintenance. This warranty applies to the original purchaser

only. All remedies under this warranty are limited to the repair or replacement of any item or items found by the factory to be defective within the time period specified.

If you have a warranty claim, first you must call our factory at the number below for instructions. You must retain proof of purchase and submit a copy with any items returned for warranty work. Upon completion of

warranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage to our products caused by accidents, fire, vandalism, negligence, misinstallation, misuse, Acts of God, or by

defective parts not manufactured by us, is not covered under this warranty.

THE WARRANTY TIME PERIOD IS AS FOLLOWS: ALL “SOFT GOODS” MANUFACTURED BY OUR COMPANY (USING PRIMARILY VINYLS, PLASTICS, AND/OR FOAM): ONE YEAR FROM DATE OF PURCHASE.

ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE CREATED HEREBY ARE LIMITED IN DURATION TO THE SAME DURATION AND SCOPE AS THE EXPRESS

WRITTEN WARRANTY. OUR COMPANY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

For further information or request for warranty work, please contact: Bestop Inc.

Customer Service

(800)346-3910

(303)465-1755

Made in China