ABB SR100A User manual

Type
User manual
REWOUND (MORE )
LOAD NEW ABB CHART
REWINDING XXX%
(STOP ) (PAUSE )
TO START RELOAD
PRESS ENTER
SECURITY ACCESS
ENTER CODE 0
LOAD CHART
PAGE
OPERATING PAGES
(Channel displays, date/time)
OPERATING PAGES
(Channel displays, date/time)
or
1
2 3
4
5
6
18
17
Withdraw cassette
Lift catch
Tension chart with
thumbwheels
Insert spindle into
new chart roll
Fit new chart
Unwind enough chart to fit over the
front and rear sprocket wheels
Feed chart
under
retaining bar
Refit cassette
to instrument
Withdraw
spindle
Remove old chart
50 mm
7
8
9
10
11
16
15
14
13
12
WELCOME TO THE SR100A
Alarms
Acknowledging 13, 15, 16, 20, 38, 69
Configuring 36
Examining alarm buffers 26
Print 40
Chart
Length 13, 19
Loading (this sheet), 7, 9
Printout 4
Review/Cue enable 24, 26, 70
Scales 42
Speed 39
Configuration
Advanced 49
Basic 29
D.C. Supply 89
Date and Time Setting 13, 19, 76
Easy View 41
Electrical Connections 84
Equations 68
Fault Finding 90
Filter Time 32
Linearizer
Custom Configuration 70
Ty p e 3 1
Mounting 81
Passwords 2, 25, 48
Pen
Capsule – Fitting 11
Options 43
Power Supply Connections 89
Printing
Channel and Data Values 54
Total Values 56
Totalizer 56
Resetting
Alarms 71
Scale Adjustment 34
Totalizer 80
Security Access 17, 25
Siting 81
Software Version 25
User
Guide
LOADING A NEW ROLL CHART
1 Press until the SECURITY ACCESS page is displayed.
2 Set the access code for the LOAD CHART page (the default is 0).
3 Select the LOAD CHART page.
4 Press to select the START RELOAD frame
5 Press
to rewind the chart.
Caution.
The chart rewinds at high speed. DO NOT stop the chart until automatic rewind
is complete.
6 If the chart is fully rewound before the motor stops, press the
key.
If the moter stops before the chart is fully rewound, press and hold
until the
remaining chart is rewound onto the removeable spool.
Caution.
Once chart loading is
complete, ensure the
correct chart type is
set in the
Chart Control
Configuration Page
see
Section 5.3.1
in
the
User Guide
.
& Press
to
resume recording.
* Press
until the
operating page is
re-displayed.
TO START RELOAD
PRESS ENTER
LOAD NEW ABB CHART
SECURITY ACCESS
ENTER CODE 0
LOAD CHART
PAGE
OPERATING PAGES
(Channel displays, date/time)
OPERATING PAGES
(Channel displays, date/time)
1
2
3
4
5
18
17
Release
tension bar
Lift chart guide
Feed chart
through
cassette
Pull back
tension bar
Fit paper into
rear tray
Pull 6 or 7 folds of chart through the cassette
and fit chart into front paper tray
Align and fit chart over lugs
Close chart guide
%
Refit cassette to instrument
Withdraw cassette
Lift catch
6
7
8
9
10
16
15
14
13
12
11
Boiler 1 Temperature
A3 236.7 °C
Raise and Lower
Sideways Scroll
Down Scroll
Pen Lift
Enter
Channel
Identifier
Bargraph/Channel Tag
Measured
Value
Units
Used for adjusting parameters or
text messages.
Lifts and lowers the pen on
successive operations.
Used to confirm selections/
adjustments.
Frame 1
Page 1 Page 2
Advance to
next page
Frame 2
Advance to
next frame
Frame 1
Frame 2
DISPLAYS AND CONTROLS LOADING A NEW FAN-FOLD CHART
1 Press until the SECURITY ACCESS page is displayed.
2 Set the access code for the LOAD CHART page (the default is 0).
3 Select the LOAD CHART page.
4 Press
to select the START RELOAD frame
5 Press to stop recording.
Note. Channel data is not buffered during chart reloading.
Caution. Once
chart loading is
complete, ensure the
correct chart type is set
in the
Chart Control
Configuration Page
see Section 5.3.1 in the
User Guide
.
& Press to
resume recording.
* Press
until the
operating page is
re-displayed.
The Company's policy is one of continuous product
improvement and the right is reserved to modify the
information contained herein without notice.
© ABB 2003 Printed in UK (09.03)
ABB Limited
Howard Road, St. Neots
Cambridgeshire, PE19 8EU
UK
Tel: +44 (0)1480 475 321
Fax: +44 (0)1480 217 948
IM/SR100A–Q Issue 1
  • Page 1 1
  • Page 2 2

ABB SR100A User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI