Page is loading ...
2-1/8” (54mm)
1” (25mm)
Mortise @ 5/32” (4mm)
deep cutout
Drill 9/64” (3.5mm)
7/8” (22mm)
7/8” (22mm)
1-1/8” (32mm)
deep
11/16” (17mm)
deep
3/8” (10mm)
3/8” (10mm)
3/8” (10mm)
3/8” (10mm)
Combi-screws
B
C
C
A
A
BB
C
D
B
B
B
B
1. MARK DOOR 2. DRILL HOLES
5. INSTALL STRIKE4. PREPARE DOOR JAMB
3. INSTALL DEADBOLT & LATCHBOLT
A. Check lock for proper backset and
door thickness of the door before
marking.
B. Fold template at correct markings
for door.
C. Mark appropriate centers for
2-1/8” (54mm) holes.
D. Mark center for 1” (25mm) diameter
latch holes in door edge.
A. Locate exact centerline of bolt and
mark centerline of jamb.
B. Mark drill points 3/8” (10mm) above
and below centerline.
C. Drill two overlapping 7/8” (22mm)
holes 1-1/4” deep for deadbolt.
Clean out hole.
D. Drill two overlapping 7/8” (22mm)
holes 11/16” deep for latchbolt into
door jamb as shown
A. Place strike box in hole. Place strike
over the strike box and use it as
pattern for cutout.
B. Chisel about 1/8” (3.2mm) deep for
ush t of box and strike
C. Install strike box and strike.
A. Place reinforcer in cutout with
screw holes as shown.
Mark & drill 3/16 (5mm) pilot
holes
B. Chisel about 1/4” (6mm) deep
for ush t of reinforcer, box
and strike.
C. Install reinforcer with 3” (76mm)
wood screws.
D. Install strike box and strike.
A. Determine backset (2-3/4”
or 2-3/8”) of the lock.
B. Drill the 2-1/8” (54mm) holes
about halfway through door face
from both sides to avoid
damaging wood surface.
C. Drill 1” (25mm) diameter holes on
door edge.
C. Insert latch bolt and dead bolt into
corresponding holes. Trace around
faceplate.
D.Chisel out excess wood until faceplate
ts at with door edge.
E. Drill (4) 9/64” (3.5mm) holes and
secure latchbolt and deadbolt with
combi-screws supplied.
A. Bolt must be retracted.
Retract bolt. (If necessary, use screw
driver to turn cam and retract bolt).
B. How to adjust for 2-3/8” (60mm)
backset.
NOTE: Rotate faceplate and push down
to move housing to next position
ADJUSTABLE DEADBOLT IS FACTORY
PRESET 2-3/4” (70MM) BACKSET
6605 Flolla St. Tel: (323) 888-6601 Email: sales@cal-royal.com
Commerce, CA 90040 USA
Fax: (323) 888-6699
Website: www.cal-royal.com
INSTALLATION INSTRUCTIONS FOR CIL INTERCONNECTED LOCKS
6. HANDING 7. HOW TO CHANGE DOOR HANDING
LH
Left Hand
LRB
Left Hand
Reverse Bevel
RRB
Right Hand
Reverse Bevel
RH
Right Hand A. Check if RIGHT-HAND or LEFT-HAND.
B. Insert push pin (provided) into the guide hole at the end of the semicircle as shown on the following diagram.
C. While push pin is inserted on the guide hole, move it along the semicircle guide until you see either “LEFT” or “RIGHT” on
the indicator window.
A. Remove inside lever from lock, esing push pin.
B. Install lock assembly into door and engage latch
as detailed.
C. Place inside mounting plate. Tighten it to lock
body with two (2) 10-32UNF x L 1-3/8” screws.
D. Install exterior deadbolt cylinder assembly with
tailpiece horizontally.
E. Tighten inside mounting plate to exterior deadbolt
cylinder with two (2) M6.0 x P1.0 x L 2-3/8” screws.
F. Install interior unit with two (2)
M5.0 x P0.8 x L11/16” screws.
G. Install inside lever.
Outside lock assembly
Lockset is factory preset for 1-3/4” (45mm) doors
Inside Mounting Plate
Intrerior Unit
Screws
(2)M6.0 x P0.8 x L 11/16”
Screws
(2)10-32UNF x L 1-1/8”
Install distance between deadbolt
and lever is 4” (102mm) and 5-1/2” (140mm)
Exterior Tailpiece
Exterior Cylinder Screws
(2) M6.0 x P1.0 x L2-3/8”
Indicator Window
Indicator
Window
Indicator Window
RIGHT HAND DOOR LEFT HAND DOOR
Guide Hole
Push Pin
Guide Hole
INTERIOR UNIT (REVERSE SIDE)
LOCK INSTALLATION
A
B
C
A. Determine and note your hand of door.
B. When standing on the exterioir side of
the door, and the hinges are to your right,
you have a RIGHT HAND DOOR.
C. If the hinges are to your left, you have a
LEFT HAND DOOR.
INSTALLATION INSTRUCTIONS FOR CIL INTERCONNECTED LOCKS
6605 Flolla St. Tel: (323) 888-6601 Email: sales@cal-royal.com
Commerce, CA 90040 USA Fax: (323) 888-6699 Website: www.cal-royal.com
5-1/2”
MARK CENTER OF
HOLE ON DOOR FACE
C
L
DRILL 1” HOLE
4”
5/32”
5/32”
MARK FOR 1-3/8” DOOR
MARK FOR 1-3/4” DOOR
MARK CENTER OF
HOLE ON DOOR FACE
MARK CENTER OF
HOLE ON DOOR FACE
DRILL 1” HOLE
DRILL 1” HOLE
7/8”
11/16”
1”
2-1/4”
2-3/8” BACKSET
2-3/4” BACKSET
C
L
C
L
C
L
C
L
C
L
C
L
FOLD ON HIGH EDGE OF DOOR
PACKED WITH PLASTIC FILLER FOR 1-1/8” FACE PLATE
TEMPLATE FOR CIL INTERCONNECTED LOCKS
SUGGESTED HEIGHT FROM
FINISHED FLOOR
2-1/8” (54mm) DIA.
2-1/8” (54mm) DIA.
2-1/8” (54mm) DIA.
/
