Kobe INX26 SQB-700-3-1 Installation guide

Category
Cooker hoods
Type
Installation guide
KOBE Range Hood
Brillia Series
INX26 SQB-700-3 Series
Model No.: INX2630SQB-700-3 (30”)
INSTALLATION INSTRUCTIONS
AND OPERATION MANUAL
IMPORTANT
READ THIS FIRST
READ BEFORE INSTALLATION
1. Carefully check all contents of package(s).
2. Thoroughly inspect the unit for any shipping damages, cosmetic
damages or defects.
3. Have a certified contractor/electrician test the unit before installation.
IF THERE IS ANY PROBLEM:
1. DO NOT INSTALL THE UNIT AND KEEP ALL ORIGINAL
PACKAGING MATERIAL.
2. Have your original invoice as proof of purchase and product serial
number ready.
3. Contact your merchant for product replacement due to shipping
damages, cosmetic damages or defects.
4. For all other issues, email customer.service@koberangehoods.com.
NO RETURN, NO REFUND, NO EXCHANGE IF:
1. PRODUCT HAS BEEN INSTALLED
2. KNOCK-OUT HOLES HAVE BEEN PUNCTURED
3. MISSING ORIGINAL PACKAGING MATEIRL
AND/OR PARTS
[ENGLISH]
- READ AND SAVE THESE INSTUCTIONS -
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .................................................................................... 1
COMPONENTS OF PACKAGE ................................................................................................. 3
INSTALLATION ......................................................................................................................... 4
OPERATING INSTRUCTIONS .................................................................................................. 9
MAINTENANCE ........................................................................................................................10
SPECIFICATIONS ....................................................................................................................11
MEASUREMENTS & DIAGRAMS .............................................................................................12
PARTS LIST .............................................................................................................................14
CIRCUIT DIAGRAM ..................................................................................................................16
TROUBLE SHOOTING .............................................................................................................17
WARRANTY .............................................................................................................................18
WARRANTY INFORMATION FORM ........................................................................................20
- READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING -
ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN
ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES
1
IMPORTANT SAFETY INSTRUCTIONS
- PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION -
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY,
OBSERVE THE FOLLOWING:
1) Installation and electrical wiring must be done by qualified professionals and in accordance with all
applicable codes and standards, including fire-rated construction.
2) When cutting or drilling into wall or ceiling, be careful not to damage electrical wiring or other hidden
utilities.
3) Ducted fans must be vented to the outside.
a) Before servicing or cleaning unit, open the light panel and SWITCH POWER OFF AT SERVICE
PANEL.
b) Clean all grease laden surfaces frequently. To reduce the risk of fire and to disperse air properly,
make sure to vent air outside. DO NOT vent exhaust air into wall spaces, attics, crawl spaces or
garages.
NOTE
-
This warranty is void without an authorized agent’s receipt or if unit is
damaged due to misuse, poor installation, improper use, mistreatment,
negligence or any other circumstances beyond the control of KOBE
RANGE HOODS authorized agents. Any repair carried out without the
supervision of KOBE RANGE HOODS’ authorized agents will
automatically void the warranty.
-
KOBE RANGE HOODS will not be held responsible for any damages to
personal property or real estate or any bodily injuries whether caused
directly or indirectly by the range hood.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE
TOP GREASE FIRE:
1) Keep all fan, baffle/spacer/filter/oil tunnel/oil container and grease-laden surfaces clean. Grease
should not be allowed to accumulate on fan, baffle/spacer/filter/oil tunnel/oil container.
2) Always turn hood ON when cooking.
3) Use high settings on cooking range ONLY when necessary.
4) Do not leave cooking range unattended when cooking.
5) Always use cookware and utensils appropriate for the type and amount of food prepared.
6) Use this unit only in the manner intended by the manufacturer.
7) Before servicing, switch power off at service panel and lock service panel (if possible) to prevent
power from switching on accidentally.
8) Clean ventilating fan frequently.
2
What To Do In The Event Of a Range Top Grease Fire
1) SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner.
KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not
go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT or 911.
2) NEVER PICK UP A BURNING PAN You May Get Burned.
3) DO NOT USE WATER, including wet dishcloths or towels a steam blast will result.
4) Use an extinguisher ONLY if:
a) You have a Class A, B, C extinguisher and know how to operate it.
b) The fire is small and contained in the area where it started.
c) The fire department has been called.
d) You can fight the fire with your back to an exit.
What To Do If You Smell Gas
1) Extinguish any open flame.
2) Do not try to turn on the lights or any type of appliance.
3) Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and
Fire Department right away.
CAUTION
1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors.
2) To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion
and exhausting of gases through the flue (chimney) to prevent back drafting.
3) Follow the heating equipment manufacturer’s guideline and safety standards such as those published
by the National Fire Protection Association (NFLA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities.
4) Activating any switch on may cause ignition or an explosion.
5) Due to the size and weight of this hood, installation by 2 persons is recommended.
ELECTRICAL SHOCK HAZARD Can result in serious injury or death.
Disconnect appliance from electric power before servicing. If equipped,
the fluorescent light bulb contains small amounts of mercury, which
must be recycled or disposed of according to Local, State, and Federal
Codes.
3
COMPONENTS OF PACKAGE
(Must keep all material for returns or refunds)
Range Hood Box
{A} KOBE Range Hood
{B} Warranty Registration Card
{C} Quick Reference Guide
{D} Baffle Filter x 2pcs
{E} Oil Tunnel x 1pcs
{F} Stainless Steel Spacer x 2pcs
{G} 6” Round Exhaust Plate
{H} Rectangular Exhaust Plate
{I} Rectangular Exhaust Vent Adapter
{J} Screws Package
{A}
{B} {C}
{D} {E}
{F} {G}
{H} {I}
{J}
FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE www.koberangehoods.com.
M4 x 35mm
QTY: 10
*Pre-Installed
4
INSTALLATION
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING
Calculation before Installation
To calculate installation, please refer to TABLE 1. (All calculation in inches)
- FORE BUILT-IN / INSERT -
SAFETY WARNING
HOOD MAY HAVE SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF REMOVING
ANY PARTS FOR INSTALLATION, CLEANING OR SERVICING.
BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD MAY
OCCUR. USING HAND TOOLS IS RECOMMENDED. DO NOT OVER TIGHTEN SCREWS.
MAKE SURE TO PREVENT ANY DEBRIS FROM ENTERING THE VENT OPENING TO AVOID
DAMAGE OR MALFUCTION.
5
Preparation Before Installation
Figure 1
Figure 2
Figure 3
Figure 4
NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT
DEBRIS FROM ENTERING THE VENT OPENING.
Decide the location of the venting pipe from the hood to the
outside. Refer to Figure 1.
A straight, short vent run will allow the hood to perform more
efficiently.
Try to avoid as many transitions, elbows, and long run as
possible. This may reduce the performance of the hood.
Temporarily wire the hood to test for proper operation before
installing.
Important: Peel protective film off the hood, if any.
Use duct tape to seal joints between pipe sections.
CAUTION: If moving the cooking range is necessary to
install the hood, turn off the power in an electric range at
the main electrical box. SHUT OFF THE GAS RANGE
MOVING A GAS RANGE. And use a protective covering to
protect cooktop and/or countertop from damage.
Customer Hood Preparation
1) The custom hood frame must be designed according to the
shape and the weight of the insert. Refer to Measurements &
Diagrams on Page 10.
2) A sturdy base (3/4-inch think plywood recommended) is needed
to sustain the weight of insert.
3) It is recommended to install front & rear stud support (not
included). Refer to Figure 2. For safety purposes, extra
installation holes on the side of the insert are provided. Prepare
the side stud support if needed.
4) Determine and mark the centerlines on the base of the hood
frame where the insert will be installed.
5) Determine the proper location for the Power Supple Cable.
Make a wiring access hole using a drill bit. Install the wire cable
and seal the gap around hole.
6) Cut out the opening where the insert will be installed.
(Figure 3)
Hood Preparation Before Installation
CAUTION: If moving the cooking range is necessary to
install the hood, turn off the power in an electric range at
the main electrical box. SHUT OFF THE GAS BEFORE
MOVING A GAS RANGE.
7) Choose the required vent option. The Round Exhaust Plate is
pre-installed for top vent.
*Note: Sample image only. May not be actual model.
6
8) For Top 3-1/4” x 10” Rectangular installation only:
- Remove the pre-installed Round Exhaust Plate (Refer to
Figure 5). Keep screws to attach Rectangular Exhaust
Plate and Rectangular Exhaust Adapter.
- Place Rectangular Exhaust Plate over vent and secure with
3 screws (Refer to Figure 6). Place Rectangular Exhaust
Adapter over the Rectangular Exhaust Plate and secure
with 2 screws (Refer to Figure 6).
- Use remaining screws to secure exhaust plate.
For Rear Vent Options Only:
NOTE: The blower is pre-installed for top vent. If installing as
rear vent, follow the steps below:
9) For Rear 6” Round installation only:
- Remove the Rear Vent Cover (Refer to Figure 4). Keep
screws to attach Round Exhaust Plate to rear vent.
- Remove the pre-installed Round Exhaust Plate from top
vent (Refer to Figure 5). Attached it to the rear vent (Refer
to Figure 7) using screws removed from vent cover.
- Use the vent cover removed from rear vent to seal top vent.
- Remove the 4 screws that secure the blower system (Refer
to Figure 8). Hold the blower to keep it from dropping as
you remove screws. Keep screws to re-attach blower.
Slowly rotate blower system to align with mounting holes at
the back of the insert. Secure blower using 4 screws (Refer
to Figure 9).
10) For Rear 3-1/4” x 10” Rectangular installation only:
- Remove the Rear Vent Cover (Refer to Figure 4). Keep
screws to attach Rectangular Exhaust Plate and
Rectangular Exhaust Adapter.
- Place the Rectangular Exhaust Plate over vent and secure
with 3 screws (Refer to Figure 10). Place Rectangular
Exhaust Adapter over the Rectangular Exhaust Plate and
secure with 2 screws (Refer to Figure 10).
- Use remaining screws to secure exhaust plate.
- Remove the pre-installed Round Exhaust Plate from top
vent and keep screws (Refer to Figure 4). Use the vent
cover removed from rear to seal top vent.
- Remove the 4 screws that secure the blower system (Refer
to Figure 8). Hold the blower to keep it from dropping as
you remove screws. Keep screws to re-attach blower.
Slowly rotate blower system to align with mounting holes at
the back of the insert. Secure the blower using 4 screws
(Refer to Figure 9).
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
*Note: Sample image only. May not be actual model.
*Note: Sample image only. May not be actual model.
*Note: Sample image only. May not be actual model.
*Note: Sample image only. May not be actual model.
*Note: Sample image only. May not be actual model.
7
Ductwork Installation
Figure 10
Figure 11
Figure 12
Figure 13
11) Determine and make all necessary cuts in the wall or ceiling for
the ductwork. NOTE: Install the ductwork before installing the
insert.
12) Use steel pipe to connect the exhaust on the hood to the
ductwork above. Use duct tape to make all joints secure and
air tight.
13) Please refer to local codes for the usage of a damper (included).
Electrical Wire
14) Connect the range hood to an outlet.
15) If hardwired is desired, cut off the plug and connect three wires
(black, white, green) to the outlet wires and cap with wire
connectors. Connect the wires according to color (ex: black to
black)
Hood Installation
NOTE: USE HAND TOOLS ONLY. DO NOT OVER TIGHTEN
SCREWS. IT MIGHT CAUSED DAMAGED TO THE
HOOD.
16) Remove 10 screws located at the bottom of the insert (Refer to
Figure 11). Carefully remove the light support panel.
17) Position the insert inside the custom wood frame and secure
the insert to the front and rear stud support (Refer to Figure 2)
by using the front and rear mounting holes (screws included).
18) For a more secure installation, use the mounting holes located
on the side of the insert.
19) Make sure insert is secure before releasing.
20) Re-install the light support panel. (Do not tighten screws)
CAUTION: MAKE SURE HOOD IS SECURE BEFORE
RELEASING.
Final Assembly
21) Install the oil tunnel into recess support near rear of hood. Refer
to Figure 12.
22) Install baffle filters. Angle baffle filter toward back of hood .
Push baffle filter up until almost level . Slide forward into
recess behind the front of hood . Lower baffle filter . Slide
back until it fits into resting position . Refer to Figure 13.
*Note: Sample image only. May not be actual model.
*Note: Sample image only. May not be actual model.
8
OPERATING INSTRUCTIONS
3-Speed Mechanical Control
NOTE: For best result, turn fan on prior to any preparation or cooking and keep fans running while
cooking. Adjust speed as necessary.
To operate the fan function
Press button to choose from speed
o Q = QuietMode™ speed
o L = Low speed
o H = High Speed
Press “OFF” to turn fan off
To operate the light function
Press the Light Control to turn lights on and off
9
MAINTENANCE
For optimal performance, clean the range hood surface and baffles regularly.
To Clean Hood Surface
CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS.
***Regular care will help preserve its fine appearance.
1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth.
2. If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of
the hood. Avoid getting cleaning solution onto or into the control panel. Follow directions of the
stainless steel cleaner. Caution: Do not leave on too long as this may cause damage to
hood finish. Use soft towel to wipe off the cleaning solution, gently rub off any stubborn spots.
Use dry soft towel to dry the hood.
3. DO NOT allow deposits to accumulate or remain on the hood.
4. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface
and cause rusting.
5. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact
with stainless steel for extended periods. Many of these compounds contain chemicals, which
may be harmful. Rinse with water after exposure and wipe dry with a clean lint free cloth.
For Baffle Filter models only: to Clean Baffle Filter / Oil Tunnel
CAUTION: DRAIN OIL FROM BAFFLE FILTERS, SPACERS & OIL TUNNEL REGULARLY TO
PREVENT OVERFLOW.
1. Remove all the baffle filters, spacers and oil tunnel. Note: Not all models have spacers and oil
tunnels.
2. Using a sponge, wash with warm soapy water. Dry completely before returning into place.
CAUTION: SHARP EDGES (NOTE: Baffle Filters are top rack dishwasher safe)
10
SPECIFICATIONS
MODEL / SIZE
INX2630SQB-700-3 / 30”
COLOR
20-Gauge Commercial Grade Stainless Steel
CONSUMPTION / AMPERE
224W / 1.5A
VOLTAGE
110V 60Hz
NUMBER OF MOTORS
1
DESIGN
Seamless / Satin Finish
FAN TYPE: CENTRIFUGAL
Single Horizontal Squirrel Cage
EXHAUST
Top
6” Round
3-1/4” x 10” Rectangular
Rear
6” Round
3-1/4” x 10” Rectangular
CONTROL
Mechanical Push Button (3-Speed)
LIGHT
3-Watt LED Light x 2
HOOD DIMENSION
(W x D x H)
30” x 18-1/2” x 12”
OPTIONAL ACCESSORIES
(W x D x H)
1) 30” Stainless Steel Back Panel
SSP30: 30” x 1/10” x 32”
2) 36” Stainless Steel Back Panel
SSP36: 36” x 1/10” x 32”
HOOD WEIGHT (lbs)
NET
GROSS
INX2630SQB-700-3 (30”)
41.0
47.0
Blower Air Capacity (cfm)
QuietMode™
Low
High
180
317
630
Sone*
2.0
4.5
7.0
*One sone is equivalent to the sound of a refrigerator at 40 decibels.
**Specifications subject to change without notice.
11
MEASUREMENTS & DIAGRAMS
***All ( ) are in millimeter.
***All inch measurements are converted from millimeters. Inch measurements are estimated.
MODEL NO.: INX2630SQB-700-3 (30”)
12
Side View Bottom View
Back View Top View
Front View
13
PARTS LIST
MODEL NO.: INX2630SQB-700-3 (30”)
NO.
DESCRIPTION
MODEL/SIZE
PART NO.
1
Rectangular Exhaust Vent Adapter
02-018
2
Rectangular Exhaust Plate
02-019
3
Round Exhaust Plate
02-020
4
LED Light (3W) x2
02-005
5
Control Switch
02-006
6
LED Light Driver
02-001
7
Capacitor (12uF) x1
02-004
8
Blower System
02-021
9
Stainless Steel Spacer (235mm x 45mm)
02-022
10
Baffle Filter (235mm x 305mm)
02-023
11
Oil Tunnel
02-024
14
MODEL NO.: INX2630SQB-700-3 (30”)
15
CIRCUIT DIAGRAM
MODEL NO.: INX2630SQB-700-3 (30”)
16
TROUBLE SHOOTING
Issue
Possible Cause
Solution
After
Installation,
both motors
and lights are
not working.
The power is not on.
Make sure the circuit breaker and the
unit’s power is ON. Use a voltage
meter to check the power supply.
The wire connection is not secure.
Check and tighten wire connection.
The control switch is defective.
Replace the control switch.
Lights are
working, but
motor(s) is
not.
The motor(s) is defective.
Replace the motor.
The capacitor(s) is defective.
Replace capacitor(s).
The control switch is defective.
Replace the control switch.
The range
hood is
vibrating.
The blower system is not secure.
Tighten the turbine impeller/squirrel
cage and air chamber.
The turbine impeller/squirrel cage is
not balanced.
Replace the turbine impeller/squirrel
cage.
Hood is not secured in place.
Check the installation of hood, tighten
the mounting bracket.
The motor is
working, but
the lights are
not working.
LED light fixture(s) is defective.
Replace LED light fixture(s).
The light wiring(s) is loose.
Check wire continuity from Control
Switch to LED Driver to LED light
fixture(s).
The control switch or LED light driver
is defective.
Replace the control switch or LED
light driver.
The range
hood is not
venting out
correctly.
The range hood is installed outside of
the manufacture recommended
clearance.
Adjust the clearance between the
range hoods and cook top to 26” to
30”. For Island range hood, the
clearance between the range hoods
and cook top is 30” to 36”.
There is no make-up air inside the
house.
Open the window to enhance the
performance of the range hood by
creating a sufficient make-up air.
Obstacle blocking the pipe work
Remove all obstacles from the duct
work.
The pipe size is smaller than the
suggested pipe size.
Change the ducting according to the
manufacture suggestion.
Cold air is
coming into
the home.
The pipe connection is not properly
sealed.
Check the pipe installation.
The damper is not properly installed or
is missing from the installation.
Check the damper installation.
The damper is not installed.
Installing the damper will help
eliminate air backflow.
17
WARRANTY
WARRANTY CERTIFICATE
In order to obtain warranty service, you must provide proof of original purchase from a
KOBE authorized Dealer. Please keep a copy of your original invoice as proof of purchase.
ONE-YEAR LIMITED LABOR WARRANTY ON KOBE BRILLIA SERIES:
For one year from the date of your original from a KOBE authorized dealer, we will repair any
parts or components free of charge that failed due to manufacturing defects. KOBE reserves
the right to replace, rather than repair the product free of charge at our sole discretion.
It is your sole responsibility to ensure the product is readily accessible for the service technician
to perform repairs. The service technician will not, under any circumstances, remove, alter
or modify any fixture built around and/or connected to the product to gain access to
perform repairs.
TWO-YEAR LIMITED PARTS WARRANTY ON KOBE BRILLIA SERIES:
For two years from the date of your original invoice from a KOBE authorized dealer, we will
provide non-consumable replacement parts or components free of charge that failed due to
manufacturing defects. Consumable parts such as light bulbs, filters, fuses, and oil cups are not
covered by this warranty.
WHAT IS COVERED:
This warranty is valid in the United States and Canada. It is non-transferable and applies only
to the original purchaser and does not extend to subsequent owner of this product. In Hawaii,
Alaska and Canada, this warranty is limited. There may be additional shipping charges for parts
and service technician travel costs in remote areas or locations 30 miles outside of KOBE
authorized service area.
WHAT IS NOT COVERED:
1. Normal wear and tear, regular service and maintenance required for the product.
2. Consumable parts such as light bulbs, filters, fuses and oil cups.
3. Chips, scratches or dents due to abuse or misuse of the product, use of corrosive and
abrasive cleaning products.
4. Damages caused by accident, fire, flood and other Acts of God.
5. Services in remote areas or locations 30 miles outside of KOBE authorized service area.
6. Labor cost incurred in connection with the removal of range hood, and reinstallation of
replacement range hood, nor does it cover any other contingent expenses.
7. Scratches inside the hood, back of the baffle filter, and inside the duct cover.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23

Kobe INX26 SQB-700-3-1 Installation guide

Category
Cooker hoods
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI