Kichler Lighting 55010BK User manual

Type
User manual
IS-55010-US
Were here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
5) Make wire connecons. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
6) Push xture to wall carefully passing mounng screws
with holes in canopy. Make sure all wires are inside
canopy and do not get pinched between wall and canopy
of xture. Note: Fixture can be mounted with glass in
the up or down posion.
7) Place the lockwasher [H] onto the mounng screws.
Thread lockup knobs[F] onto mounng screws and
ghten to secure xture to wall.
8) Carefully raise glass[G] to the xture. Slip the smaller
opening over the socket and t the glass against the
socket cover.
9) Thread the socket ring[I] onto the socket. Tighten socket
ring to secure glass in place (DO NOT over ghten).
10) Insert recommended bulb (Not supplied).
Fixture Diagram
Parts List
Installaon Instrucons
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
[A] Mounting
Strap
[B] Canopy
[C] Mounting
Screws
[D] Outlet Box
[E] Strap
Mounting
Screws
[F] Lockup Knobs
[G] Glass
[H] Lockwasher
[I] Socket Ring
A
C
D
E
B
G
F
H
I
1) Find the appropriate threaded holes on mounng
strap[A] that align with hole distance in canopy[B].
Thread mounng screws[C] into threaded holes starng
from outlet box[D] side.
2) Aach mounng strap to outlet box with strap mounng
screws[E]. The mounng strap can be adjusted to suit
posion of xture.
3) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
4) If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector (Not provided) aer following the above steps.
Never connect ground wire to black or white power
supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
  • Page 1 1
  • Page 2 2
  • Page 3 3

Kichler Lighting 55010BK User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI