American Standard 0445.400.020 User manual

Brand: American Standard

Model: 0445.400.020

Type: User manual

J25

spec_0445EdgmerePedSink4/17

EDGEMERE

PEDESTAL SINK

FINE FIRECLAY

EDGEMERE

PEDESTAL SINK

❏ 0445.800 Faucet holes on 8" (203mm) centers

❏ 0445.400 Faucet holes on 4" (102mm) centers

❏ 0445.100 Center hole only

 •Finereclay

 •Classicstyledrectangularpedestallavatory

 •Rearoverow

 •Suppliedwithmountingkit

 •RightHeight

forgreatercomfortduringuse

 •Faucetledgewithlargedeckarea(faucetnotincluded)

 •Design coordinates with Edgemere

Fixtures and Faucets

 •PedestaltopscanalsobeusedwithEdgemereConsoleTable

Nominal Dimensions:

25" x 19-1/2" x 35-5/8"

(635 x 495 x 905mm)

❏ 0445.008 Pedestal top-8" (203mm) centers

❏ 0445.004 Pedestal top-4" (102mm) centers

❏ 0445.001 Pedestal top-center hole only

❏ 0039.000 Pedestal only

❏ 8719.000 Console table

❏ 7720.018Optionaldecorativep-trapdrain(notshown)

Bowl sizes:

17-1/8" (435mm) wide,

12" (305mm) front to back,

5-1/4" (133mm) deep

Compliance Certications -

Meets or Exceeds the Following Specications:

•ASMEA112.19.2/CSAB45.1

To Be Specied:

❏ Color: ❏ White

❏ Console Finish: ❏ Chrome ❏BrushedNickel

❏ Faucet Finish:

❏ Supplies:

❏ P-Trap: ❏ Chrome ❏BrushedNickel

❏ Nipple:

*Seefaucetsectionforadditionalmodelsavailable

SEEREVERSEFORROUGHING-INDIMENSIONS

J26

spec_0445EdgmerePedSink4/17

EDGEMERE

PEDESTAL SINK

FINE FIRECLAY

OPEN TO

FLOOR

FINISHED WALL

OR BACKSPLASH

SUPPLIES

AS REQ'D

1-1/4" O.D.

WASTE

1-1/4" O.D.

TAILPIECE

FINISHED

FLOOR

*22-3/4"

(578mm)

*20-1/2"

(521mm)

(202mm)

8-3/8"

(213mm)

7/8"

(22mm)

2X HOLES FOR

ANCHOR BOLTS

FAUCET MOUNTING HOLES:

SINGLE HOLE, 4" (102mm)

OR 8" (203mm)

8-1/2"

(215mm)

25"

(635mm)

19-1/2"

(495mm)

DRAIN CHASE

(50mm)

(203mm)

35-5/8"

(905mm)

FINISHED

FLOOR

FINISHED

WALL

FINISHED

WALL

35-11/16"

(906mm)

19-1/2"

(495mm)

4-7/16"

(112mm)

6-5/16"

(160mm)

1-9/16"

(40mm)

21-1/2"

(545mm)

8-3/8"

(213mm)

30-1/2"

(775mm)

28"

(710mm)

34-1/16"

(866mm)

8-1/8"

(207mm)

24-1/2"

(622mm)

25"

(635mm)

17-1/2"

(444mm)

20-1/4"

(514mm)

5-1/2"

(140mm)

FAUCET MOUNTING HOLES:

SINGLE HOLE, 4" (102mm)

OR 8" (203mm)

2X HOLES FOR

ANCHOR BOLTS

NOTES:

DIMENSIONSSHOWNFORLOCATIONOFSUPPLIESAND“P"TRAPSARESUGGESTED.

▼ PEDESTALANCHORINGSCREWSNOTINCLUDED.

■SUITABLEFORREINFORCEMENTONLY.ACTUALDIMENSIONSMUSTBETAKENFROMFIXTURE.

FITTINGNOTINCLUDEDANDMUSTBEORDEREDSEPARATELY.

PROVIDESUITABLEREINFORCEMENTFORALLWALLSUPPORTS.

INSTALLATIONINSTRUCTIONSSUPPLIEDWITHLAVATORY.

IMPORTANT:DimensionsofxturesarenominalandmayvarywithintherangeoftoleranceestablishedbyANSIStandardA112.19.2

Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibility isassumedforuseofsupersededorvoidedpages.

PEDESTAL CONFIGURATIONS METAL CONSOLE CONFIGURATIONS

American Standard 0445.400.020 User manual

American Standard 0445.400.020 User manual

American Standard 0445.400.020 User manual

Related papers

Other documents