iCarsoft Multisystem Scanner i930 User manual

Multi-system Scanner Series User's Manual

EN

I

Disclaimer

All information, illustrations, and specications contained in this

manual are based on the latest information available at the time

of publication. The right is reserved to make change at any time

without notice.

Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or the

Multi-system Scanner, please read this user’s manual first

carefully and observe the following safety precautions at a

minimum whenever working on a vehicle:

Always perform automotive testing in a safe environment.•

Do not attempt to operate or observe the tool while driving •

a vehicle. Operating or observing the tool will cause driver

distraction and could cause a fatal accident.

Wear safety eye protection that meets ANSI standards.•

Keep clothing, hair, hands, tools, test equipment, etc. away •

from all moving or hot engine parts.

Operate the vehicle in a well-ventilated work area: Exhaust •

gases are poisonous.

Put blocks in front of the drive wheels and never leave the •

vehicle unattended while running tests.

Use extreme caution when working around the ignition •

coil, distributor cap, ignition wires and spark plugs. These

components create hazardous voltages when the engine is

running.

Put the transmission in P (for A/T) or N (for M/T) and make •

sure the parking brake is engaged.

Keep a fire extinguisher suitable for gasoline/chemical/ •

electrical res nearby.

Don’t connect or disconnect any test equipment while the •

ignition is on or the engine is running.

Keep this tool dry, clean, free from oil/water or grease. Use a •

mild detergent or a clean cloth to clean it if necessary.

II

Multi-system Scanner Series User's Manual

Table of Contents

1 INTRODUCTION ................................................................... 1

2 Product Descriptions .......................................................... 2

2.1 Outline of Multi-system Scanner ..................................... 2

2.2 Specications.................................................................. 3

2.3 Accessories..................................................................... 3

2.4 Product Troubleshooting ................................................. 3

2.5 Power supply .................................................................. 4

3 Tool Setup ............................................................................ 5

3.1 Connection...................................................................... 5

3.2 Tool Setup ....................................................................... 6

3.3 Tool Information .............................................................. 7

4 Diagnose .............................................................................. 8

5 Upgrading ............................................................................. 9

6 FAQ ..................................................................................... 12

Multi-system Scanner Series User's Manual

EN

1

1 INTRODUCTION

The Multi-system Scanner Series covers the following models:

Multi-system Scanner i980, Multi-system Scanner i960, Multi-

system Scanner i930, Multi-system Scanner i906, Multi-

system Scanner i908 and Multi-system Scanner i902, which is

especially designed for the DIY users and the servicemen of

small service workshop.

Featuring the color LCD display and personalized function

menu, the Multi-system Scanner Series can diagnose full

electronic control system of single vehicle model.

Note: The MULTI-SYSTEM SCANNER may automatically

reset while being disturbed by strong static electricity. THIS IS A

NORMAL REACTION.

2

Multi-system Scanner Series User's Manual

2 Product Descriptions

2.1 Outline of Multi-system Scanner

1

2

3

4

5

6

7

8

9

10

Figure 2-1

1 Power Indicator Lights up when your tool is

powered on.

2 Cable with OBD II

Connector

Connects the Multi-system

Scanner to the vehicle’s Data Link

Connector (DLC).

3 LCD Display Indicates test results.

4/7 UP/DOWN Button Move cursor up or down for

selection.

5 OK Button Conrms a selection (or action)

from a menu list.

Multi-system Scanner Series User's Manual

EN

3

6/8 RIGHT/LEFT Button Move cursor right or left for

selection; Or turn page up or

down when more than one page

is displayed.

9 USB Port Connects to computer to update

the Multi-system Scanner.

10 ESC Button Returns to previous menu.

2.2 Specications

1) Screen: 2.8” TFT 262K true color, 320*240dpi

2) Input voltage range: 9~18V

3) Operating current: <100mA@12V (Typical)

4) Power consumption: <1.2W (Typical)

5) Operating temperature: 32°F~122°F / 0°C~50°C

6) Storage temperature: -4°F~158°F / -20°C ~70°C @ RH60%

7) Outline dimension: 4.7’*3.2’*1.0’ / 121*82*26 mm (L x W x H)

8) Weight : < 300g

2.3 Accessories

1) User’s Manual -- Instructions on tool operations

2) USB cable -- Connect to a computer for upgrading online

2.4 Product Troubleshooting

Vehicle Linking Error

A communication error occurs if the scan tool fails to

communicate with the vehicle’s ECU (Engine Control Unit). You

need to do the following to check up:

4

Multi-system Scanner Series User's Manual

A) Verify that the ignition is ON;

B) Check if the scan tool’s OBD II connector is securely

connected to the vehicle’s DLC;

C) Verify that the vehicle is OBD2 compliant;

D) Turn the ignition off and wait for about 10 seconds. Turn

the ignition back to on and continue the testing;

E) Verify the control module is not defective.

Scan tool doesn’t power up

If the scan tool won’t power up or operates incorrectly in any

other way, you need to do the following to check up:

A) Check if the scan tool’s OBD II connector is securely

connected to the vehicle’s DLC;

B) Check if the DLC pins are bent or broken. Clean the DLC

pins if necessary.

C) Check vehicle battery to make sure it is still good with at

least 9.0 volts.

2.5 Power supply

The power of the Multi-system Scanner is provided via the

vehicle’s Data Link Connector (DLC). Follow the steps below to

power it up:

1) Find DLC on vehicle;

Note: A plastic DLC cover may be found for some vehicles

and you need to remove it before plugging the OBDII cable.

2) Plug the connector at the end of OBD II cable to the

vehicle’s DLC.

Multi-system Scanner Series User's Manual

EN

5

3 Tool Setup

3.1 Connection

1) Turn the ignition off.

2) Locate the vehicle’s 16-pin Data Link Connector (DLC).

The DLC (Data Link Connector) is the standardized 16-cavity

connector where diagnostic code readers interface with the

vehicle’s on-board computer. The DLC is usually located 12

inches from the center of the instrument panel (dash), under

or around the driver’s side for most vehicles. If Data Link

Connector is not located under dashboard, a label should be

there telling location. For some Asian and European vehicles,

the DLC is located behind the ashtray and the ashtray must be

removed to access the connector. If the DLC cannot be found,

refer to the vehicle’s service manual for the location.

Figure 3-1

3) Plug the OBDII cable into the vehicle’s DLC.

4) Turn the ignition on. Engine can be off or running.

5) After nishing, press [OK] button to enter Main Menu.

6

Multi-system Scanner Series User's Manual

Figure 3-2

CAUTION: Don’t connect or disconnect any test equipment

with ignition on or engine running.

3.2 Tool Setup

This option enables you to change your interface language and

turn the beeper on/off.

Select [Tool Setup] in the Main Menu and press [OK] to enter.

Figure 3-3

1) Language: To swtich to the desired language.

Choose [Language] and press [OK] to enter. Use [

] / [ ] key

to select any language and press [OK] to conrm, the system

will switch to the chosen language interface.

Multi-system Scanner Series User's Manual

EN

7

2) Beeper: To turn the Beeper ON/OFF.

Choose [Beeper] and press [OK] to enter. Use [

] / [ ] to select

ON/OFF and press [OK] to conrm.

3.3 Tool Information

This option allows you to view: boot version, display program

version, diagnostic program version, serial number and register

code.

Figure 3-4

Press [ESC] to return to the previous screen.

8

Multi-system Scanner Series User's Manual

4 Diagnose

This function is specially designed to diagnose electronic control

system of single vehicle model.

Figure 4-1

Refer to the owchart illustrated as below to diagnose a vehicle:

Select “Diagnose”

Automatic

(Note: This mode allows

your tool to scan the vehicle

test system automatically)

Manual Select

(Note: In this case, you need to choose the

desired system manually. Just follow the

on-screen instructions to proceed.)

Select test system

Select test function

Select Vehicle Model

(Note: For different

vechicles, vehicle make

selection may differ.

Generally, we can choose

a vehicle via make year.

But for BENZ, we need to

choose it via chassis.)

Select Vehicle

Manufacturer

Read version

information

Read fault code

Clear fault code

Data stream

Note: For vehicles manufactured by different

vendors, it is possible that it has different

diagnostic menus. For details, please follow

the instructions on the screen to proceed.

Multi-system Scanner Series User's Manual

EN

9

5 Upgrading

Follow the steps described as below to proceed registration and

update:

1. Go to http://www.icarsoft.com or http://www.icarsoft.us and

download the update tool to the computer.

2. Run the iCarsoft_Update_Setup.exe le, and follow the on-

screen instructions to install the update tool (compatible with

Windows XP and Windows 7 operating system).

3. Launch the program when installed, a screen similar to

Figure 5-1 will appear:

Figure 5-1

4. In Figure 5-1, type in the Product Serial Number which is

located at the back of the tool.

5. After the serial number is entered, click Update to jump to

the registration page. Enter the following information and

click OK.

10

Multi-system Scanner Series User's Manual

Figure 5-2

(If you need the Register Code, please refer to steps 6~9.)

(If you have the Register Code, directly proceed to step 10.)

6. The Register Code can be found in your tool. Connect one

end of the supplied USB cord to your tool, and the other end

on the computer.

7. After the tool has powered up and entered the main menu

screen, move the highlight bar on the Tool Information and

press the [OK] button.

8. The Register Code shown in Figure 5-3 is the Register Code

needed in step 5.

Figure 5-3

(Return to step 5 and input the Register Code and then

proceed)

Multi-system Scanner Series User's Manual

EN

11

9. Reopen the update tool, select the updates you would like

to perform, and then click Download to start downloading.

Figure 5-4

10. Once all steps are done, the registration process is

complete.

12

Multi-system Scanner Series User's Manual

6 FAQ

Here we list some frequently asked questions and answers

relating to Multi-system Scanner.

Question: System halts when reading data stream. What is the

reason?

Answer: It may be caused by a slackened connector. Please

turn off the Multi-system Scanner, rmly connect the connector,

and switch on it again.

Question: Screen of main unit ashes at engine ignition start.

Answer: Caused by electromagnetic disturbing, and this is

normal phenomenon.

Question: There is no response when communicating with on-

board computer.

Answer: Please conrm the proper voltage of power supply and

check if the throttle has been closed, the transmission is in the

neutral position, and the water is in proper temperature.

Question: Why are there so many fault codes?

Answer: Usually, it’s caused by poor connection or fault circuit

grounding.

Note: All pictures illustrated here are for reference and

demonstration purpose only and this User’s Manual is subject to

change without prior notice.

Page is loading ...

iCarsoft Multisystem Scanner i930 User manual

This manual is also suitable for

iCarsoft Multisystem Scanner i930 User manual

in other languages

Related papers

Other documents