Canon DP-V2420 User manual

Brand: Canon

Model: DP-V2420

Type: User manual

• Beforeuse,besuretoreadthisguide,includingthesafetyandhandlingprecautions.

• Readingthisguidewillhelpyoulearntousethevideodisplayproperly.

• Storethisguidesafelysothatyoucanuseitinthefuture.

English

Instruction Manual

Operation Guide

Video Display



Firmware ver. 1.1

/ 

Firmware ver. 1.4



Firmware ver. 1.3



Firmware ver. 1.5

/ 

Firmware ver. 1.4

Table of Content

Introduction 3

Aboutthismanual  3

Trademarks  3

Operating the Video Display 4

BasicoperationstousetheOSDmenu  4

AdjustingImageQualityWhileViewingtheEntire

Image  5

TemporarilySavingParameters(AnchorPoint

Setting)  7

Enlargingthedisplay(Zoomfunction)  7

ChangingImageQualityAutomaticallyAccording

toInputSignal  8

Adjustimagequalityonleft/rightsideofscreen

(imagecomparisonmode)  9



Changingthescreendisplayarea  9

    

Performingcalibrations  10

Export/Import  11

SetDate/Time  14

InputtingCharacters  14

UsingtheFunction(F)Buttons  15

UsingtheChannel(CH)Button  16

CheckingSignalInformationandStatusofthe

MainUnit  19

  

Operatingthevideodisplayusinganexternal

device[REMOTEterminal(GPI)]  19

Operatingthevideodisplayusinganexternal

device[LANterminal]  20

Operatingthevideodisplayusinganexternal

device[USBterminal:Wi-Ficonnection]  21

Useawebbrowsertoremotelyoperatethe

videodisplay  23

OSD Menu 26

Adjustment  26

ChannelSettings  48

DisplaySettings  53

AudioSettings  57

MarkerSettings  58

FunctionSettings  65

PictureFunctionSettings  79

Network/IMDSettings  84

SystemSettings  86

SignalInformation  94

SystemInformation  94

Supported Signal Format 95

Image/Frame Display 110

Error Messages 113

Troubleshooting 116

Software Used in This Product 119

Index 124

About the User Manual for the Display

• TheproductincludesanInstructionManualorSetupGuide.Beforeusingtheproduct,besuretoread

“ImportantUsageInstructions”and“SafetyInstructionsandHandlingPrecautions”.

• TheOperationGuide(thisdocument)explainsthefunctionsavailableontheversionofthermwareshownon

thecoverpageaswellassetupprocedures.

Introduction

TheOnScreenDisplay(thereafterreferredtoOSD)defaultlanguagesettingisEnglish.TochangetheOSDmenu

languagesetting,pleaserefertop.86.

About this manual

ThescreenoftheDP-V3120isusedasanexampleinthisGuide.SomeoftheillustrationusedintheGuidehavebeen

simpliedforclarity.

Conventions used in this manual

:Indicatesareferencepage.

Note:Indicatesanote.

Reference:Indicatesreferenceinformation.

CAUTION:Indicatesanitemyoumustobserve.

 [Adjustment] [PictureMode]:PressingtheMENUbuttonshowstheOSDMenulevels.Youcanmove

betweentheitemsandselectfromthem.

• Thefollowingsymbolsshowdifferencesinfunctionsandsettingsdependingontheproduct.

      :Explanationsareapplicabletotheindicatedproducts.

:Indicatesfunctionsonlyavailablewithapaidlicense,forthestatedmodels.

Trademarks

• HDMI,HDMIlogo,andHigh-DenitionMultimediaInterfacearetrademarksorregisteredtrademarksofHDMI

LicensingAdministrator,Inc.intheU.S.andothercountries.

• VESAisaregisteredtrademarkortrademarkofVideoElectronicsStandardsAssociationintheU.S.andother

countries.

•

Wi-Fi,WPA,andWPA2areregisteredtrademarksoftheWi-FiAlliance.

• AppleandSafariaretrademarksofAppleInc.registeredintheUnitedStatesandothercountries.

• GoogleandGoogleChromearetrademarksorregisteredtrademarksofGoogleLLC.

• Otherproductandcompanynameshereinaretrademarksorregisteredtrademarksoftheirrespectiveowners.

OperatingtheVideoDisplay

Usingbuttonsandjogdialonthevideodisplay,youcanadjustimagequalityandconguresettingsforinputsignals.In

addition,youcanassignfrequentlyusedfunctionstotheCH(Channel)andF(Function)buttons.

Basic operations to use the OSD menu

MENUbutton

Opens/closestheOSD

menu,ormovesupone

levelinamenu.

RESETbutton

Resetstheitemstobeadjustedusingthesliderand

enteredcharacters.

Jogdial

 orrotation:Usedtomovetoadifferentitemandchange

settings.

Press:Conrmssettingsormovestheselectionframeup/down1level.

ThevideodisplaysettingsarechangedfromtheOSDmenu.

1 Open the OSD menu.

•PresstheMENUbutton.

2 Select the Main Menu.

•SelecttheMainMenuitemusingthejogdialandpressitto

determinetheselection.

3 Select the Sub Menu.

•SelecttheSubMenuitemusingthejogdialandpressitto

determinetheselection.

MainMenu

SubMenu

SettingOptions

Operating the Video Display

4 Select the setting to change.

•Selectthesettingtochangeusingthejogdialandpressitto

determinetheselection.YouwillbereturnedtotheSubMenu

itemselectionscreen.

5 Exit menu.

•PressingtheMENUbuttonwillreturnyoutotheMainMenu

itemselectionscreen.PressingtheMENUbuttonagainwill

closethemenuscreen.

Note

• Toadjustimagequality,warming-upisnecessarytostabilizethebrightnessofthevideodisplay.Waitatleast10minutesafter

turningonthepowerbeforeuse.

• TheOSDmenuandsliderwilldisappearautomaticallyifnooperationisperformedforapproximately1minute.TheFbuttonwill

disappearautomaticallyifnooperationisperformedforapproximately10seconds.

• Thesettingsthatcannotbeset,aregrayedout.

• Thefollowingfunctionscanbereturnedtotheirfactorydefaultsettingsortheiranchorpoint( 7)bypressingtheRESETbutton,

afteradjustingtheimagequality.

- [Contrast],[Brightness],[Chroma],[Sharpness],[Power],[Saturation],[Offset],[Slope]

When[PictureMode] [User1–7]:Whenexecutingcalibration,pressingtheRESETbuttonwhileadjustingtheimagequalitywill

returnyoutothesettingsaftercalibration.

Adjusting Image Quality While Viewing the Entire Image

YoucanadjusttheOSDmenutodisplayasaslideratthebottomofthescreen.Thisallowsfortheimagequalitytobe

adjustedwhilstitisdisplayedonthescreen.

1 Press the jog dial when the selection frame is on setting options.

•Asliderappearsatthebottomofthescreen.

2 Make adjustments using the jog dial with using the slider as

guide.

3 When adjustments are completed, press the jog dial.

•ThescreenreturnstotheoriginalOSDmenu.

Operating the Video Display

Color temperature detailed settings (gain, bias)

YoucanadjustRGBallatonceorindividuallywhenthescreensforadjusting[Gain]or[Bias]aredisplayed.

1 Select [Adjustment] [Color Temperature].

•[GainR],[GainG],[GainB],[BiasR],[BiasG],and[BiasB]canbesetindividuallyusingthejogdial(  ).

2 Select one.

•Thesettingscreenfor[Gain]or[Bias]willbedisplayed.

3 Switch the guide in the upper right area of the slider screen using the jog dial ( ).

•Theindicationchangesto[RGB],[R],[G],and[B].Selecting[RGB]willallowyoutoadjustRGBasawhole.

4 When adjustments are completed, press the jog dial.

•ThescreenreturnstotheoriginalOSDmenu.

Color temperature detailed settings (xy values)

1 Select [Adjustment] [Color Temperature].

2 Select [Custom (xy)].

•Youcanset[x]and[y]individuallyusingthejogdial(  ).

3 Select either [x] or [y].

•Thecolormapisdisplayed.

4 Adjust [x] with the



and [y] with .

•Theadjustedvalueisindicatedbythe" "markonthecolormap.

5 When adjustments are completed, press the jog dial.

•ThescreenreturnstotheoriginalOSDmenu.

Defaultvalue

Lastusedvalue

Currentvalue

Operating the Video Display

Temporarily Saving Parameters (Anchor Point Setting)

Youcantemporarilysaveparametersfor[Contrast],[Brightness],[Chroma],[Sharpness],and[HDRRange].See 32

forsettinganchorpointsduringCDLadjustment.

1 Select [Adjustment] [Anchor Adjustment].

2 Press the jog dial, and when the conﬁrmation screen appears, select [OK].

•Theparameterissavedandtheanchorpointisset.

3 Adjust the image quality again and press the RESET button on the video display.

•Returnsyoutotheanchorpointforeachfunction.

CurrentvalueLastusedvalue

Anchorpoint

Note

• Executing[Adjustment] [Reset]or[SystemSettings] [ResetAllSettings]resetssavedanchorpointsandthesettingsreturn

totheirfactorydefaultvalues.

• Whencalibrationisexecuted,thevaluesaresavedasanchorpoints.

Enlarging the display (Zoom function) ( 55)

Thezoomdisplaypositioncanbeadjusted,andthezoommagnication(2x,4x,8x)canbeselected.

1 Select [Display Settings] [Zoom].

2 Select [Zoom Preset].

•Selectapresetzoomdisplay.

3 Select [Position].

•Thezoomadjustmentscreenisdisplayed.

- Tomovethedisplayposition:Movethejogdial(  orrotation).

- Toreturntothecenter:PresstheRESETbutton.

4 When adjustments are completed, press the jog dial.

•ThescreenreturnstotheoriginalOSDmenu.

Note

• WhenmagnifyingtheimageandtheOSDmenuisnotbeingdisplayed,

- youcansetthemagnicationratiobypressingthejogdial.

- Youcanmovethedisplaylocationbymovingthejogdial

(  orrotation).

- YoucansetthefollowingfunctionsusingtheCHbutton:

CH1:Selectzoomtype;CH2:Switchbetweenzoompresets(Zoom1/Zoom2/Zoom3);CH3:Zoomoff

Zoom 2 [x4]

Operating the Video Display

Changing Image Quality Automatically According to Input Signal

Onthisvideodisplay,youcanautomaticallychangetheimagequalityaccordingtovideoresolutionormetadata.

Changing [Picture Mode] automatically ( 51)

1 Select [Channel Settings] [Select Channel].

•Selectthechannel.

2 Select [Channel Settings] [Picture Mode] [Type].

3 Select the Type using the jog dial.

Changing by individual video resolution (4K/2K)

Select[4K/2K].

Changing according to video resolution (4K/2K) or metadata (SDI)

Select[Automatic].

4 Select the Picture Mode.

Changing the image quality setting according to video metadata (HDMI) ( 38)

1 Select [Adjustment] [Picture Mode] [User 1-7].

•Selectanythingfrom[User1]to[User7].

2 Select [Channel Settings] [Picture Mode] [Type].

•Selectotherthan[L/R].

3 Select [Adjustment] [Detail Settings] [HDMI Link] [Automatic Adjustment].

•Select[On].

•See[HDMILink]( 38)forthecongurablesettings.

Note

• Whenautomaticchangingofimagequalityaccordingtovideoresolution(4K/2K)orSDImetadataisset,

informationshowingwhichresolution(4K/2K,etc.)isselectedwillbedisplayedatthetoprightofthe

menuscreen.

Operating the Video Display

Adjust image quality on left/right side of screen (image comparison mode)

Youcandividethescreenintwoandadjusttheimagequalityontheleftandrightsidesofthescreenindividually.

1 Select [Channel Settings] [Picture Mode] [Type].

•Select[L/R].

2 Select the screen to adjust image quality.

•WhentheOSDmenuisopened:

- Pressthe inthejogdialwhenthe[Adjustment]mainmenuisselected.

- PresstheCH1buttonwhenthe[Adjustment]mainmenuorsubmenuisselected.

•WhentheOSDmenuisclosed:Switchusingthejogdial(  ).

•

Eachtimethetargetscreenisswitched,theset[PictureMode]isdisplayedatthetop.

3 Adjust the image quality on the selected screen.

Note

• WheninImageComparisonmode,aniconshowingwhichscreen(L/R)isselectedforimagequality

Adjustment,isdisplayedattherighttopofthe[Adjustment]menuscreen.

• Thefunctionsthatcannotbeusedwhentherightscreenisselectedareasfollows:

- SubMenuitemsfor[Adjustment]:[Contrast],[BacklightControl],[HDR/SDRView],[Calibration]*

,[PeakLuminanceControl]*

,

[BoostContrast]*

 *

      *

  *

  

• Whentwoscreensaredisplayed,youcanadjusttheimagequalityoneachscreenindividuallyandcomparethem.

- Whentwoscreensaredisplayingthesameimage([SingleInputDualView] 52)

- Whentwoscreensaredisplayingdifferentimages([MultiView(Dual)] 49)

- YoucancheckHDR(HighDynamicRange)displayandSDR(StandardDynamicRange)displayside-by-side.([HDR/SDRView]

37)

Changing the screen display area

Whenavideosignalof4096x2160isinput,theleftandrightpartswillbetrimmedfordisplay.

1 Select [Display Settings] [Screen Scaling].

•Select[NativeInputResolution]or[200%].

2 Press the jog dial ( ) while the OSD menu is closed.

•Shiftstotheleftorright.

Operating the Video Display

Performing calibrations ( 37)

Youcanperformcalibrationusinganexternalsensor,withoutusingacomputer.

ThesupportedexternalsensorsareKonikaMinoltaDisplayColorAnalyzersCA-310andCA-210.Besuretoalsoread

theinstructionmanualoftheCA-310andCA-210.

ThevideodisplaycanperformmeasurementorcalibrationofthedisplayusingtheDP-VColorAdjustmentsoftware.

RefertotheCanonwebsitefortheDP-VColorAdjustment.

1 Connect the display color analyzer to the USB port of the main unit.

2 Select [Adjustment] [Picture Mode] [User 1–7].

3 Select [Adjustment] [Detail Settings] [Calibration].

•Seteachtargetvalue.

4 Select [Start].

•Pleasefollowtheinformationindicatedonthescreen.

5 Initialize the sensor.

•SetthemodedialoftheUniversalMeasuringProbeto[0-CAL].

•Pressthejogdialofthevideodisplay,select[OK],andexecuteinitialization.

6 Place the universal measuring probe pointing at the center of the video display.

•Setthemodedialoftheuniversalmeasuringprobeto[MEAS]andplacetheprobeasshownbelowaccordingto

thedisplayedcontent.Pressthejogdialofthevideodisplay,select[OK],andexecutecalibration.

KonicaMinoltaUniversalMeasuringProbe

CA-310support:CA-PU32,CA-PU35

CA-210support:CA-PU12,CA-PU15

KonicaMinolta

DisplayColorAnalyzerCA-310,CA-210

FortheDP-V2411

7 Finish calibration.

•Whenthemessage[Calibrationiscompleted.]isdisplayed,pressthejogdialandselect[OK].

•Ifthemessage[Calibrationerror.]isdisplayed.

Calibrationhasbeenterminatedduetoanerror.Themainunitreturnstothestatebeforecalibration.( 113)

•Tocancelcalibration

Pressthejogdialduringcalibrationandselect[Cancel].Themainunitreturnstothestatebeforecalibration.

Operating the Video Display

Note

• Performmatrixcalibrationofthedisplaycoloranalyzerpriortocalibration.Ifcalibrationisperformedwithoutperformingmatrix

calibration,anerrormayoccur.RefertotheCA-310andCA-210instructionmanualforthedetailoperation.

• Warming-upisnecessarytostabilizethebrightnessofthevideodisplay.Waitatleast10minutesafterturningonthepowerbefore

performingcalibration.

• Performcalibrationinadarkroomsothatnoexternallightentersthesensor.Ifexternallightentersthesensor,lowbrightness

characteristicscannotbecalibratedcorrectly.

• DuetothecharacteristicofLCDpanelandindividualdifferenceofCA-310andCA-210,thecalibrationresultsmaydiffer.

Export/Import

Youcanexport/importLUTandCDLparametersaswellasmainmenusettings.

LUT Import ( 35)

1 Insert the USB memory stick containing the LUT ﬁle into the USB port of the video display.

2 Select [Adjustment] [Detail Settings] [LUT Import].

3 Select the LUT ﬁle to import.

•Inthe[Filename]eld,searchanddisplayalewithextension".clut"and".cube"intherootfolder.

4 Select the LUT type.

•Refertothe"ConceptDrawingofDisplayImageProcessingandLUT"( 12).

5 Select the LUT No. to save the LUT.

6 Select the color gamut that will be the standard (when [Gamut LUT] under [LUT Type] is selected).

•SelectthecolorgamutusedwhencreatingtheLUT.

7 Select [Execute].

•Whentheconrmationscreenappears,select[OK].Importstarts.

Note

• Importof[1D-LUT]and[3D-LUT]canalsobesetfrom[Adjustment] [CDL/UserLUT] [1D-LUT]or[3D-LUT] [LUTImport].

• TheLUTle(.clutformat)isproprietarytoCanonVideoDisplay.RefertotheCanonwebsitefortheleformatandhowtocreate

theLUTle.

• Upto1000LUTimportlesarerecognized.

• YoucandeletetheimportedLUT,aswellasrenametheLUT( 36).

ThecongurationofLUTles(cubeformat)isshownbelow.



LUT ﬁlename

Type of characters that can be used One-bytealphabeticalcharactersandnumbersonly

No. of characters that can be used Upto48characters(includingtheextension)

Extension .cube

Operating the Video Display



LUT ﬁle format

TITLE

ASCII24characterscanbeused.

*DisplayedintheOSDmenuofthedisplayasaselectionitem.(Upto24characters)

LUT_1D_SIZE Specifyonefrom128/256/512/1024/2048/4096.

LUT_3D_SIZE Specifyonefrom9/17/33/65.

Table Data For1D-LUT,onlyRedisenabled.(GreenandBluearenotused.)

DOMAIN_MIN

DOMAIN_MAX

LUT_1D_INPUT_RANGE

LUT_3D_INPUT_RANGE

Unsupported.

•

Forthelinefeedcode,use“CR(carriagereturn)”,“LF(linefeed)”,or“CR+LF”.

• Forthecharactercode,use“Shift-JIS”,“EUC-JP”,or“UTF-8(with/withoutBOM)”.

• Filesinwhichboth1D-LUTand3D-LUTarewrittenarenotsupported.



Concept Drawing of Display Image Processing and LUT

   

Range

conversion

1D-LUT

(UserLUT)

Range

conversion

CDL/3D-LUT

(UserLUT)

1D-LUT

(GammaLUT)

3D-LUT

(Gamut LUT)

ImportImport

Gamma 2.2

Color Gamut

(User selectable)

Color Temperature

(User selectable)

(fixed)

Color

Temperature

Base Color

Gamut



CDL/3D-LUT

(UserLUT)

1D-LUT

(GammaLUT)

3D-LUT

(Gamut LUT)

Import Import Import

Gamma 2.2

Color Gamut

(

User selectable

)

Color Temperature

(User selectable)

(fixed)

Color

Temperature

Base Color

Gamut

Operating the Video Display

Export/Import Main Menu Settings ( 90)

1 Select [System Settings] [Export/Import].

2 Select [Export] or [Import].

 Exporting

Select[Target]from[USB],[User1]to[User3]or[LAN].

Export[USB]totheUSBmemoryand[User1]to[User3]tothebuilt-inmemoryofthemainunit.Whenyou

select[LAN],theleisexportedtoadisplayconnectedviaLAN.

Ifyouselected[USB]or[User1]to[User3],select[Filename].

• Thefactorydefaultis[dinfo_dpv****.dat](****:Numberoftheproductname).Youcanchangethenameof

theletobeexportedtotheUSBmemorywithin16one-bytecharactersincludingalphabeticalcharacters,

numbers,andsymbols.

Ifyouselected[LAN],select[Display].

• SelectthedisplaytowhichtoexportthesettingsfromthedisplaysconnectedviaLAN.

 Importing

Select[Target]from[USB]or[User1]to[User3].

Specifythedestinationtosavetheletobeimported.

Select[Filename]when[USB]isselected.

In[Settings],select[All]orMainMenuname.

3 Select [Execute].

•Whentheconrmationscreenappears,select[OK].Export/Importstarts.

Note

• Afterexportto[User1]to[User3],youcanselectthecongurationsatstartupfrom[User1]to[User3]in[PoweronSetting]in

[SystemSettings](

•

Toexportthisdevice'ssettingstootherCanondisplays:

- Ifadisplaymodelhasfunctionswithdifferentmenusettingsorsettingranges,somesettingswillnotbecorrectlyexported

(settingswillnotbechanged,willreverttofactorydefaults,etc.)

- Whentheexportiscompleted,amessagewillappearonthetargetdisplay.

Exporting/Importing CDL Parameters ( 32)

1 Select [Adjustment] [CDL/User LUT].

2 Select [CDL 1-8].

3 Select [Detail Settings] [CDL Export] or [CDL Import].

 Exporting

Select[CDLPreset].

Selectaleformat".ccc"or".cdl".

 Importing

Select[Filename].

Select[CDLPreset].

4 Select [Execute].

•Whentheconrmationscreenappears,select[OK].Export/Importstarts.

Operating the Video Display

Note

• Theexportedleisautomaticallysavedunderthename"YYYYMMDDhhmmss_Presetname.ccc(cdl)".

• Upto1000CDLimportlesarerecognized.

Set Date/Time ( 86)

ThissectiondescribeshowtosetthevideodisplayDate/Time.ThevideodisplayDate/Timewillberesetifthepower

cordisnotconnectedforapproximately20days.

1 Select [System Settings] [Date/Time].

•AscreentoinputtheDate/Timeappears.

2 Set the Date/Time.

•Theselectionframemovesandnumberschangeasyouoperatethejogdial.Repeatuntilyoucompletesetting

theyear,month,date,hour,andminute.

3 Press the jog dial when you are ﬁnished.

•Theselectionframemovesto[OK].

4 Check the content and press the jog dial to conﬁrm the settings.

Reference

• Whenselecting[Cancel]orpressingMENUbuttonbeforeselecting[OK],thesettingswillberesetandthepreviousscreenwillbe

displayed.

Inputting Characters

Thissectiondescribeshowtoinputthecharacters.

1 When the character input screen is displayed, use the

jog dial (

) to select the area you wish to input.

2 Select characters using the jog dial ( or rotation).

•Thefollowingcharacterscanbeselected:Press 

buttonstodisplaythemonebyone.

 Alphanumericcharacters:AtoZ,atoz,0to9

 Symbols:,.:;‘`-+/=%&!?#_|$^~@{}[]<>

()space

•Charactersthatcannotbeenteredareautomaticallyskipped.

3 Repeat steps 1 and 2 until the desired text has been input.

4 Press the jog dial when you are ﬁnished.

•Theselectionframemovesto[OK].

5 Check the content and press the jog dial to conﬁrm the settings.

Reference

• Whenselecting[Cancel]orpressingMENUbuttonbeforeselecting[OK],thesettingswillberesetandthepreviousscreenwillbe

displayed.

•

Toeraseacharacterintheselectionframe,presstheRESETbuttononthevideodisplay.

Operating the Video Display

Using the Function (F) Buttons

YoucanassignfunctionstotheFbuttonsonthevideodisplaytoexecutetheminstantly.Youcanassigndifferent

functionsonFbuttonsinthenormalandCDLmodesrespectively.

1 Select [System Settings] [Function/Channel Button] [Display Function] or [Display Function

(CDL)].

•Thebuttonselectionscreenwillbedisplayed.

2 Select the button name and press the jog dial.

3 Select the function to assign.

•Refertothe"FunctiontoallowregistrationforthedisplayFbuttons( 92)"fortheavailablefunctions.

4 Press the jog dial.

•Thesettingisconrmed.

Thefollowingcontentisassignedtofunctionbuttonsonthevideodisplaybyfactorydefault.

Fbutton Normalmode CDLmode

F1 PictureMode CDL/UserLUT

F2 Brightness CDLSOP/SAT

F3 TC/ALM CDL/UserLUTBypass

F4 WFM/VEC SingleInputDualView

F5 Histogram/FrameLuminance FalseColor

F6 PixelValueCheck RangeCheck

F7 ZoomPreset 2020OutsideofGamutView

F8 FrameHold

   BoostContrast

 PeakLuminanceControl

CompareView

Reference

• HoldingtheFbuttondownwilldisplaythefunctionselectionscreen,andyoucansetthefunctionyouwishtoregister.

• YoucancheckthefunctionassignedtotheFbuttonsofthemainunit.

Openthe  [SystemSettings] [OSDSettings] [FunctionButtonGuide]menuandselect[On].Pressing/movingthe

jogdial(  ,orRotate)whileOSDisnotshowingwilldisplaythelistoffunctions.Selectingafunctionfromthelistand

pressing/moving( )thejogdialwilldisplaythedetailedsettingsscreen,orexecutethatfunction.

Pressing whilethelistoffunctionsisdisplayedswitchesbetweennormalmodeandCDLmode.

Operating the Video Display

Using the Channel (CH) Button

Youcanassignchannels(varioussettingsrelatedtoinputsignal)totheCHbuttonsonthevideodisplayandswitch

channelsinstantly.

1 Select [System Settings] [Function/Channel Button] [Display Channel].

•Thebuttonselectionscreenwillbedisplayed.

2 Select the button name and press the jog dial.

3 Select the channel to assign.

•See[ChannelSettings]( 48)forthecongurablesettings.

4 Press the jog dial.

•Thesettingisconrmed.

Operating the Video Display

Thefollowingcontentisassignedtochannelbuttonsonthevideodisplayandtoeachchannelbyfactorydefault.

CH CH1 CH2 CH3 CH4 CH5

InputConguration 12-3G/HD-SDI HDMI 3G-SDIRAW

12-3G/HD-SDI 12-3G/HD-SDI

 3G/HD-SDI HDMI 3G-SDIRAW 3G/HD-SDI 3G/HD-SDI

6G/3G/HD-SDI HDMI 3G-SDIRAW 6G/3G/HD-SDI 6G/3G/HD-SDI

SelectInputSignal Automatic Automatic Automatic Automatic Automatic

ImageDivision Automatic Automatic Automatic Automatic Automatic

LinkOrder Automatic Automatic Automatic Automatic Automatic

Format Automatic Automatic Automatic Automatic Automatic

AudioInput Automatic Automatic Automatic Automatic Automatic

Marker/TC/CameraInfoInput InputA InputA InputA

InputA InputA

InternalSync Off Off Off Off Off

ChannelName (Blank) (Blank) (Blank) (Blank) (Blank)

PictureMode Type

Normal Normal Normal 4K/2K L/R

PictureMode

PictureModeL

Resolution4K

ITU-RBT.709 ITU-RBT.709 CINEMAEOS

SYSTEM

User1

(2020PQ)

User1

(2020PQ)

PictureModeR

Resolution2K

ITU-RBT.709

Payload UHD/PQ User1(2020PQ)

UHD/HLG User2(2020HLG)

UHD ITU-RBT.2020

709/PQ —

709/HLG —

709

ITU-RBT.709

VANC —

Unknown —

Camera

CINEMAEOS

SYSTEM

CINEMAEOSSYSTEM

ARRI User6

VARICAM User7

SingleInputDualView Off Off Off Automatic Off

Separator Off Off Off Off White

Operating the Video Display

CH CH6 CH7 CH8 CH9 CH10 and up

InputConguration

12-3G/HD-SDI 12-3G/HD-SDI 12-3G/HD-SDI 12-3G/HD-SDI —(Notset)

 3G/HD-SDI 3G/HD-SDI 3G/HD-SDI 3G/HD-SDI —(Notset)

6G/3G/HD-SDI 6G/3G/HD-SDI 6G/3G/HD-SDI 6G/3G/HD-SDI —(Notset)

SelectInputSignal Automatic Automatic Automatic Automatic Automatic

ImageDivision Automatic Automatic Automatic Automatic Automatic

LinkOrder Automatic Automatic Automatic Automatic Automatic

Format Automatic Automatic Automatic Automatic Automatic

AudioInput Automatic Automatic Automatic Automatic Automatic

Marker/TC/CameraInfoInput

InputA InputA InputA InputA InputA

InternalSync Off Off Off Off Off

ChannelName (Blank) (Blank) (Blank) (Blank) (Blank)

PictureMode Type

L/R 4K/2K L/R L/R Normal

PictureMode

PictureModeL

Resolution4K

User1

(2020PQ)

User2

(2020HLG)

User2

(2020HLG)

User2

(2020HLG)

ITU-RBT.709

PictureModeR

Resolution2K

ITU-RBT.709

Payload UHD/PQ User1(2020PQ)

UHD/HLG User2(2020HLG)

UHD ITU-RBT.2020

709/PQ —

709/HLG —

709

ITU-RBT.709

VANC —

Unknown —

Camera

CINEMAEOS

SYSTEM

CINEMAEOSSYSTEM

ARRI User6

VARICAM User7

SingleInputDualView

Automatic Automatic Off Automatic Off

Separator Off Off White Off Off

Note

• HoldingtheCHbuttondowndisplaysthechannellist,allowingtheusertoselectthedesiredchannel.When[SelectInputSignal]

issetto[Automatic],theinputsignallistisdisplayedandthesignalcanbechangedtemporarily*.

*    Whenonlythe12G-SDI/6G-SDIsignalisinputorwhenavideothatcanbesimultaneouslydisplayedwiththe

12G-SDI/6G-SDIsignalisinput

Whenonlythe6G-SDIsignalisinputorwhenavideothatcanbesimultaneouslydisplayedwiththe6G-SDIsignalisinput

Operating the Video Display

Checking Signal Information and Status of the Main Unit

Thevideodisplayisequippedwithabannerdisplayfunction.

1 Press the jog dial when the OSD menu is closed.

•Thechannelname,signalinformation,andstatusofthemainunitwillbedisplayedinthebanner.Itwill

automaticallydisappearafter6seconds.

Note

• Youcanselecthowthebannerisdisplayed([Banner] 87).

• Youcanmonitortheinputsignalstatus.([SignalMonitoring] 72)

• Formoredetailedsignalinformation,pleaserefertothesectionon[SignalInformation]( 94).

• The[Detectingsync.]bannerwillcontinuetoappearuntiltheinputsignalissynchronized.

Operating the video display using an external device [REMOTE terminal

(GPI)]

YoucanoperatethevideodisplayusinganexternaldeviceconnectedtotheREMOTEterminalandexecutethe

functionsregisteredineachpin.Remoteoperationispossibleonlywhenthevideodisplayisturnedon.

PinlayoutforREMOTEterminal

PinNo. Signal Factorydefault

1 Pin1 CH1

2 Pin2 CH2

3 Pin3 CH3

4 Pin4 TimeCode

5 Pin5 TallyGreen Atallyappearsatthe

topofthescreen.*

6 Pin6 TallyRed

7 Pin7 PowerOn

8 Pin8(GND) —

*  Thetallylightlights.

1 Connect an external control device to the REMOTE terminal.

2 Select [System Settings] [Remote(GPI)].

•Thepinselectionscreenwillbedisplayed.

3 Select a pin number and press the jog dial.

4 Select the function to assign.

•Pleasesee[Remote(GPI)]( 86)forsettablefunctions.

5 Press the jog dial.

•Thesettingisconrmed.

Operating the Video Display

Operating the video display using an external device [LAN terminal]

ThevideodisplaysupportsTelevisionSystemsLtd.’s“TSLUMDProtocolVer.5.0”.Youcanoperatethevideodisplay

usinganexternaldeviceconnectedtotheLANterminalanddisplaycharactersandtallylightsonthescreen.Thereare

twotallylights,ontheleftandright.Upto16characterscanbedisplayed.

Tallydisplay(left) Characterdisplay Tallydisplay(right)

1 Connect an external control device to the LAN terminal.

2 Set [SCREEN] and [INDEX] to [0x0000] in the TSL Protocol settings.

3 Select [Network/IMD Settings] [In Monitor Display].

4 Select [Control]

 

[TSL Ver. 5.00].

•Thiswillallowoperationfromanexternalcontroldevice,anddisplaycharactersandtallylights.

5 Select [Position] [Top] or [Bottom].

•Thissetsthepositionwherecharactersandtallylightswillbedisplayed.

Note

• When[MultiView(Dual)]or[MultiView(Quad)]isdisplayed,setthe[INDEX]settingtofrom[0x0001]to[0x0004].

• Theportnumberforthecontrollingisxedat"45000".

• With[InMonitorDisplay]youcanalsodisplayuser-selectedcharactersonthescreen.( 85)

Page is loading ...

Canon DP-V2420 User manual

Canon DP-V2420 User manual

Canon DP-V2420 User manual

Related papers

Other documents