BLACK+DECKER BRVA425B00 User manual

Brand: BLACK+DECKER

Model: BRVA425B00

Category: Robotic vacuum cleaners

Type: User manual

This manual is also suitable for

BRVA425B10

www.blackanddecker.ae

BRVA425B00-B5

BRVA425B10-B5

AR FR EN

ENGLISH (Original instructions)

Get access to the BLACK+DECKER® Connected Home App

Now available on the App Store & Android App on Google Play

ENGLISH

(Original instructions)

Important Safety Instructions

To reduce the risk of injury or damage, keep these

safety precautions in mind when setting up, using and

maintaining your Robot.

• Read all safety and operating instructions before

operating your Robot.

• Retain the safety and operating instructions for

future refrence.

• Heed all warnings on your Robot, battery,charging

Dock and in the owner's manual.

• Follow all operating and use instructions.

• The external ﬂexible cable or cord of the power

supply unit can’t be replaced; if the cord or plug is

damaged, the power supply unit should be

disposed of.

• This product is designed to be plugged into a

standard outlet only. Product may not be used with

any type of power converter. Use of power

converters will immediately void the warranty.

• CAUTION: Only charge one of the following robot

batteries: maximum 14.4V, max 2600mAh Ni-MH or

maximum 2600mAh Li-ion battery. Other type of

batteries may burst causing injury. Always contact

Customer Care for the correct replacement of your

battery.

• Always charge and remove the battery from your

robot and accessories before long-term storage or

transportation.

• The battery must be removed from this device

before this device is disposed. To remove the

battery from this device, rst remove the screws on

the bottom, then remove the main PCB and

unscrew the battery cover using a screwdriver.

Remove the battery by disconnecting the quick

connector.

Warning: Chemical Exposure: If the battery pack is

leaking, do not allow the liquid to come in contact

with skin or eyes. If contact has been made, wash the

aected area with copious amounts of water and seek

medical advice. Place the battery (the used battery

pack included when the robot will be disposed) in a

sealed plastic bag and dispose of safely according to

local environmental regulation.

Warning: Fire or Explosion Hazard: Do not crush or

dismantle battery packs. Do not heat or place the

battery pack near any heat source or direct sunlight. Do

not incinerate or short-circuit the battery pack. Do not

subject batteries to mechanical shock.

• Contact your local waste management authority for

battery recycling and disposal regulations in your

area.

• Your robot is not a toy. Do not sit or stand on robot.

Children and pets should be supervised when your

robot is operating.

• Robot is for indoor use only.

• Do not use non-rechargeable batteries. Use only the

rechargeable battery supplied with the product. For

replacement, purchase identical robot battery or

contact robot Customer Care for alternative battery

options.

• Store and operate robot in room temperature

environments only.

• Do not spray or pour liquids on your Robot.

• Do not use any other power supply cord. For

replacement cords, please contact Customer Care to

ensure proper selection of country speciﬁc power

supply cord.

• Do not use robot to pick up sharp objects, glass, or

anything that is burning or smoking.

• Do not immerse the battery pack in any liquid.

• Do not use robot to pick up spills of water bleach,

paint, or other chemicals, or anything wet.

• Before using robot, pick up objects like clothing,

loose papers, pull cords for blinds or curtains, power

cords, and any fragile objects. If robot passes over a

power cord and drags it, there is a chance an object

could be pulled oﬀ a table or shelf.

• If the room to be cleaned contains a balcony, a

physical barrier should be used to prevent access to

the balcony and ensure safe operation.

• Do not place anything on top of your Robot.

• Be aware that the robot moves on its own. Take care

when walking in the area that the Robot is

operating in to avoid stepping on it.

• Do not operate the Robot in areas with exposed

electrical outlets in the ﬂoor.

• Do not use this device on an unﬁnished, unsealed,

waxed or rough ﬂoor. It may result in damage to the

ﬂoor and this device. Use only on hard ﬂoor surfaces

or low pile carpet.

• This device has been designed to be used on ﬂoors

without scratching them. We still recommend that

you test this device on a small area of the room to

be cleaned to ensure no scratches are made before

cleaning the whole room.

• When the machine is not in use, please adjust the

power button at the bottom of the machine to OFF,

prevent battery drain.

• Please charge your robot for 6 hours before ﬁrst

use.

Battery and Charging / Information

Lithium-ion Battery

Important: Lithium-ion batteries and products that

contain Lithium-ion are subject to stringent

transportation regulations. If you need to ship this

product (with the battery included) for service, travel or

any other reason, you MUST comply with the following

shipping instructions:

• Remove the Lithium-ion battery from the product.

• Place a piece of tape over the battery 's metal

charging contacts.

• Reinstall the battery (with the tape on it) in the

product and secure the battery door.

• Package the product in its original packaging or in

your own packaging that prevents any movement

during transportation

• Ship via ground transportation only (no air

shipping).

Battery Storage

If storing robot oﬀ the Charging Dock, remove the

battery ﬁrst. Then store Robot and the battery in a cool,

dry place.

The symbol on the product or its packaging

indicates:

Do not dispose of electrical appliances as unsorted

municipal waste, use separate collection facilities.

Contact your local authority for information regarding

the collection systems available. If electrical appliances

are disposed of in landﬁlls or dumps hazardous

substances can leak into the groundwater and get into

the food Chain, damaging your health and well-being.

Please contact your local or regional waste authority for

more information on collection, reuse and recycling

programs.

ENGLISH (Original instructions)

1About Your Robot

1.1 Robot

Bumper

Anti-collision Sensors

Anti-Drop Sensors

Charging Contact Pins

Swivel Wheel

Side Brushes

Battery Pack

Rolling Brush

Wheels

Power Switch

Dust Bin

Dock Button

To send Robot back to the Charging

Dock, press on Robot or press on the

Remote Control.

Auto cleaning Start/Stop button

Press to start or pause Cleaning.

LED Light

Bottom

OFF

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

1.2 Accessories

1.3 Charging Dock

Charging Dock Adapter Cleaning Brush

Dust Bin

4 x Side Brushes

Boundary strip

Rolling brush 2 x Cleaning Cloths

Signal Transmission Area

Charging Indicator

Charging Contact Pins

Water Tank Sponge Filter and High

Eﬃciency Filter

ENGLISH (Original instructions)

1.4 Remote Control

1.5 Light indicator

Mode and Time Display Screen

Return to Charging Dock

Start / Stop

Auto Cleaning

Control Cleaning Direction

Install 2 AAA batteries before using the remote control for the ﬁrst time. Make sure the positive and negative ends are facing

the correct polarity direction as marked in the battery compartment.

Time Setup

Spot Cleaning

Random cleaning

Schedule Setup

Edge Cleaning

Max Sunction

Robot status Light

Charging Orange light breathes

Charging ﬁnished Green light ON

Standby mode Green light ON

Error Red light ON/ﬂashing

Low battery Orange light ON

Cleaning Green light ON

Sleeping mode Light Oﬀ

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

2Using Your Robot

2.1 Quick Start

3. 4.

Plug in the Charging Dock, and tuck the rest of the wire into the the bottom of Charging Dock.

Note: this must be done to prevent the unit from becoming stuck.

Charging Dock Position

1. Place the Charging Dock on a hard, level surface and against a wall.

3. Connect the round connector of the adapter into the power socket on the Charging Dock and the other end into a wall outlet.

2. Place the charging Dock again the wall & make sure the place is open & uncluttered

area leaving at least.

• 2 meter (6.5 feets) in front of the Charging Dock

• 1 meter (2.3 feets) on both sides of the Charging Dock.

Install the Charging Dock in a location that robot can easily access. It is recommended to place the Charging Dock against

a wall, and on a hard-level surface rather than on rugs or carpets. Always keep the Charging Dock plugged in, otherwise

robot will not automatically return to it.

Install Side Brushes

Attach side brushes to the bottom of robot by

pressing a brush into each slot.

Turn on the main power switch on the bottom of robot

ENGLISH (Original instructions)

2.2 Robot Cleaing Operation

Activate the Robot

Place robot onto the Charging Dock, making sure the metal charging contacts on the

Charging Dock match up with those underneath the Robot.

If successful you will hear a series of tones. once the Power button illuminates

robot is ready for use.

Start Cleaning Cycle

• Press the power button Once to wake up the Robot

• Press the power button again to start a cleaning cycle.

If its battery gets low before ﬁnishing a cleaning cycle, Robot will return to the Charging Dock

to recharge.

lf the Charging Dock is inaccessible, Robot will not be able to recharge. It will return to its

starting location and the cleaning cycle will end. Place the Robot manually on

Charging Dock for charging. (Refer Activate the Robot)

Pause

• To pause the Robot during a cleaning cycle press the but ton or press the

button on Remote Control.

• To resume the cleaning cycle, press button again.

• To send robot back to The Charging Dock, press button.

Note: The actions listed above can also be managed from the Remote Control.

Power OFF

• Turn oﬀ the main power switch on the bottom of robot.

Auto Cleaning

• At the start of a cleaning cycle, Robot will map out your home and cleaning

it eﬃciently.

• The Robot has the ability to clean around all edges and in-between and around

chair legs and furniture.

• Robot continues this process until it has cleaned entire level of your home.

If its battery gets low before ﬁnishing a cleaning cycle, Robot auto returns to

the Charging Dock to recharge.

• Once Robot ﬁnishes its cleaning cycle, it will return to the Charging Dock to

recharge.

Wet Mop Feature

Robot supply a water tank that the robot can ﬂoor

mops Cleaning for your home

1. Attach the cloth and ﬁll in the water tank with water.

2. Remove the dust bin.

3. Put back the water tank to robot and start the Robot.

Note: This is not necessary if you are only using dry clean mode.

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

Spot Cleaning

When you select Spot Cleaning, Robot intensely cleans a localized area by

spiraling outward about 3 feet(1 meter) in diameter and then spiraling inward to

where it started. When Spot Cleaning, Robot boosts is vacuum power to provide

the best cleaning possible where you need it. To use Spot Cleaning, place Robot

on top of the localized debris and press (Spot) on the Remote Control.

Max Vacuuming Cleaning

Robot increases its vacuum power to provide a deeper clean when you press the

button on Remote control. Max cleaning mode defaults to "OFF" otherwise.

Through the MAX button on the remote control, you can adjust the suction in turn.

Edge Cleaning

After Robot ﬁnishes cleaning the open areas of your ﬂoor, it uses Edge Clean to

ensure that it has cleaned along walls and around furniture Legs. This feature allows

the robot to quickly clean only edges in a room by pressing the button on

Remote Control.

Random cleaning

Press the button on the remote control to start random cleaning.

2.3 Cleaning Schedule

Robot has cleaning schedule settings which allow you to customize when it cleans your home. These settings

are available only through the Remote Control.

Note: Please make sure the Remote is close to the Robot while setting the Clock or Schedule.

Set the Remote Control's Clock

Press button on Remote Control, and

then the hour section begins to ﬂash in the

clock display setting window.

Press or button to select the desired

ﬁgures. Press the or button to select

the minute or hour section

And then press the button. the Robot

will "BEEP" when the clock setting completed.

ENGLISH (Original instructions)

Setting Cleaning Schedule

Press button on Remote Control, and

then the hour section begins to Hash in the

Cleaning Schedule display setting window.

Press and hold button approximately 4 seconds on Remote Control, the Robot

will "BEEP" when the Cleaning Schedule process cancel completed.

With the Boundary Strip, you can keep Robot away from any area or item you do not want Robot to clean. Robot will

recognize the Boundary Strip and will not cross into the blocked-oﬀ area.

Note:When setting Cleaning Schedule, ensure the time on Remote Control is correct.

Press or button to select the desired

ﬁgures. Press the or button to select

the minute or hour section.

And then press the button. the Robot

will "BEEP" when the Cleaning Schedule

setting completed.

Cancel the Cleaning Schedule

2.4 Use The Boundary Strip

Identify the area or item you do not want Robot to get close to.

If necessary, use scissors to cut the Boundary Strip to a shorter length.

Be sure to correctly measure the length before cutting.

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

ENGLISH (Original instructions)

Apply adhesive tape to lay the Boundary Strip ﬂat on the ﬂoor.

Make sure the strip is placed FLAT on the ﬂoor.

To keep Robot running at peak performance, perform the following care procedures. If the robot's cleaning performance

worsens, make sure to empty the bin, clean the ﬁlter and roller brush.

Robot Part Cleaning Replacement Frequency

Dust Bin After each use

Filters Once every week Every 2 months

Rolling Brush Once every week Every 6-12 months

Side Brushes Once every month Every 3-6 months(or when visibly worn)

Brush Guard Once every month Every 3-6 months(or when the silicone rubber strip

on the brush guard becomes visibly worn)

Sensors Once every month

Charging Pins Once every month

Swivel Wheel Once every month

Recommended cleaning / replacement frequency :

Regular Robot Care

3.1 Emptying Robot 's Bin

Press bin release button to remove the bin. Open bin’s door to empty it

1. 2.

ENGLISH (Original instructions)

3.2 Cleaning Robot 's Filter

3.3 Cleaning Robot 's Rolling Brush, Side Brush, Swivel Wheel and Sensors.

Remove ﬁlter by grasping the white tab.

Take out the rolling brush, clean the vacuuming aisle by a cloth.

Clean the rolling brush. Cut down the hair

winded in the rolling brush with the provided

cleaning tool's knife.

Remove the side brush, use a cloth to remove

the dust from the brush.

Dust oﬀ the cliﬀ sensors to maintain the best

performance.

Pull out the swivel wheel, then clean the Swivel

Wheel with the cleaning tool.

Shake oﬀ debris by tapping the ﬁlter against your

trash container.

2. 3.

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

Beeps Error Solution

01 1 Gyroscope error Keep the robot at a stable place to

restart and do not move the machine

02 2Bumper error Check the bumper and remove any

object that could be blocking it

03 3 Anti-Drop sensor error check for dirt on bumper and clean the

drop sensors

04 4Low power or charging error Robot voltage is too low and needs

manual charging

Beeps Error Solution

01 1 Driving wheel error Check if the drive wheel is blocked

02 2Side brushes error Check if the side brush is blocked and

clean the side brush

03 3 Fan error Remove debris from and clean the air

ducts channel

04 4Roller brush error Check if the roller brush is entangled

and clean the roller brush

Troubleshooting

light indicator

Any error that occurs during operation will be indicated by the robot through light status and beeps.

Beeps and red light ﬂashing:

Beeps and red light always on:

Tips

If the above method can not solve the problem, please try the following:

1. turn on the power switch at the bottom of the robot and restart.

2. If the problem cannot be solved by restarting, please contact the after-sales service center.

ENGLISH (Original instructions)

Frequently asked questions

Problems Solutions

Robot cannot be activated.

• Make sure the main power switch is in the ON position.

• Make sure the battery is fully charged.

• Replace the batteries (2 AAA) in the Remote Control.

• Make sure the remote control is within range (16 ft/5 m) of robot.

• If you still have trouble, turn oﬀ the main power switch

and then turn it back on.

The remote control does not work. • Replace the batteries in the Remote Control.

• Make sure robot is turned on and fully charged.

Robot stops working suddenly.

• Check if robot is trapped or stuck on an obstacle.

• Check if the battery level is too low.

• If you still have trouble, turn oﬀ the main power.

switch, wait for 2 seconds, and then turn it back on.

You can’t schedule cleaning.

• Make sure the main power switch on the bottom of robot is turned on.

• Make sure the time, time of day (AM/PM), and the scheduled time have

been set correctly.

• Check if robot’s power is too low to start cleaning.

Suction power is weak.

• Check if any obstructions are blocking the suction inlet.

• Empty the dust bin.

• Clean the ﬁlters with a vacuum cleaner or a cleaning brush.

• Check if the ﬁlters are wet due to water or other liquid on the ﬂoor. Air-

dry the ﬁlters completely before use.

Robot can’t be charged.

• Check if the indicator on the Charging Dock lights up. If not, contact the

service center to repair or replace the Charging Dock.

• Dust oﬀ the charging contact pins with a dry cloth.

• Check if you can hear a beep when robot is return the Charging

Dock. If not, contact the service center to repair or replace the

Charging Dock.

Robot can’t return to the Charging Dock.

• Remove objects within 3 ft/1 m to the left and right side and within

6 ft/2 m of the front of the Charging Base.

• When robot is in the vicinity of the Charging Dock, it will return more

quickly. However, if the Charging Dock is located far away, Robot will

need more time to return. Please be patient as it works its way back.

• Clean the charging contact pins.

The rolling brush doesn’t rotate. • Clean the Rolling Brush.

• Check if the Rolling Brush and brush guard have been installed properly.

Robot movements or travel path are abnormal. • Clean the sensors carefully with a dry cloth.

• Restart robot by turning the power switch oﬀ and on.

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

ENGLISH (Original instructions)

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you ﬁnd one day that your BLACK+DECKER

product needs replacement, or if it is of no further use

to you, do not dispose of it with other household waste.

Make this product available for separate collection.

• BLACK+DECKER provides a facility for recycling

BLACK+DECKER products once they have reached

the end of their working life. This service is provided

free of charge. To take advantage of this service

please return your product to any authorised repair

agent who will collect them on our behalf.

• You can check the location of your nearest

authorised repair agent by contacting your local

BLACK+DECKER oﬃce at the address indicated in

this manual. Alternatively, a list of authorized

BLACK+DECKER repair agents and full details of our

after-sales service and contact are available on:

www.2helpU.com.

Warranty

BLACK+DECKER is conﬁdent of the quality of its

products and oers an outstanding warranty.

This warranty statement is in addition to and in no way

prejudices your statutory rights.

If a BLACK+DECKER product becomes defective due to

faulty materials, workmanship or lack of conformity,

within 24 months from the date of purchase,

BLACK+DECKER warranty to replace defective parts,

repair products subjected to fair wear and tear or

replace such products to ensure minimum

inconvenience to the customer unless:

The product has been used for trade, professional

or hire purposes;

The product has been subjected to misuse or

neglect;

The product has sustained damage through foreign

objects, substances or accidents;

Repairs have been attempted by persons other

than authorised repair agents or BLACK+DECKER

service sta.

To claim on the warranty, you will need to submit proof

of purchase to the seller or an authorised repair agent.

You can check the location of your nearest authorised

repair agent by contacting your local BLACK+DECKER

oﬃce at the address indicated in this manual.

Alternatively, a list of authorised BLACK+DECKER repair

agents and full details of our after-sales service and

contacts are available on the Internet at:

www.2helpU.com.

Black and Decker (Overseas) GmbH (Dubai Branch)

PO Box 17164, Dubai, United Arab Emirates

FRANÇAIS

(Traduction des instructions d'origine)

lorsque le robot sera mis au rebut) dans un sac en

plastique scellé et éliminez-la en toute sécurité

conformément à la réglementation locale en matière

d'environnement.

Avertissement : Risque d'incendie ou d'explosion :

N'écrasez pas et ne démontez pas les batteries. Ne

chauez pas, et ne placez pas la batterie près d'une

source de chaleur ou sous la lumière directe du soleil.

N'incinérez pas et ne court-circuiter pas la batterie. Ne

soumettez pas les batteries à des chocs mécaniques.

• Contactez les autorités locales chargées de la

gestion des déchets pour connaître les règles de

recyclage et d'élimination des batteries en vigueur

dans votre région.

• Votre robot n'est pas un jouet. Ne vous asseyez pas

ou ne vous tenez pas debout sur le robot. Les

enfants et les animaux domestiques doivent être

surveillés lorsque votre robot fonctionne.

• Le robot ne doit être utilisé qu'à l'intérieur.

• N'utilisez pas de piles non rechargeables. Utilisez

uniquement la batterie rechargeable fournie avec le

produit. Pour la remplacer, achetez une batterie de

robot identique ou contactez le service clientèle du

robot pour obtenir d'autres options de batterie.

• Conservez et utilisez le robot uniquement à

température ambiante.

• Ne vaporisez pas et ne versez pas de liquides sur

votre robot.

• N'utilisez pas d'autres cordons d'alimentation. Pour

les cordons de remplacement, veuillez contacter le

service clientèle an de vous assurer de bien choisir

le cordon d'alimentation spécique au pays.

• N'utilisez pas le robot pour ramasser des objets

tranchants, du verre ou tout ce qui brûle ou fume.

• N'immergez pas la batterie dans du liquide.

• N'utilisez pas le robot pour ramasser de l'eau de

Javel, de la peinture ou d'autres produits chimiques,

ou tout autre objet mouillé.

• Avant d'utiliser le robot, ramassez les objets tels que

les vêtements, les papiers, les cordons de stores ou

de rideaux, les cordons d'alimentation et tout objet

fragile. Si le robot passe sur un cordon

d'alimentation et le traîne, un objet risque d'être

arraché d'une table ou d'une étagère.

Consignes de sécurité importantes

Pour réduire les risques de blessures ou de dommages,

gardez à l'esprit les consignes de sécurité suivantes lors

de l'installation, de l'utilisation et de l'entretien de votre

robot.

• Lisez toutes les instructions de sécurité et

d'utilisation avant d'utiliser votre robot.

• Conservez les instructions de sécurité et

d'utilisation pour vous y référer ultérieurement.

• Respectez tous les avertissements ﬁgurant sur le

robot, la batterie, la station de charge et le manuel

d'utilisation.

• Suivez toutes les instructions de fonctionnement et

d'utilisation.

• Le câble ﬂexible externe ou le cordon du bloc

d'alimentation ne peuvent pas être remplacés ; si le

cordon ou la che sont endommagés, le bloc

d'alimentation doit être mis au rebut.

• Ce produit est conçu pour être branché dans une

prise standard uniquement. Le produit ne peut être

utilisé avec aucun type de transformateur de

puissance. L'utilisation de transformateurs de

puissance annule immédiatement la garantie.

• ATTENTION : Ne chargez que l'une des batteries de

robot suivantes : 14,4 V maximum, 2600 mAh

Ni-MH maximum ou 2600 mAh maximum Li-ion.

Les autres types de batteries risquent d'éclater et

de provoquer des blessures. Contactez toujours le

service clientèle pour le remplacement correct de

votre batterie.

• Chargez et retirez toujours la batterie de votre

robot et de ses accessoires avant tout stockage ou

transport à long terme.

• La batterie doit être retirée de cet appareil avant sa

mise au rebut. Pour retirer la batterie de cet

appareil, retirez d'abord les vis situées sous

l'appareil, puis retirez le circuit imprimé principal et

dévissez le couvercle de la batterie à l'aide d'un

tournevis. Retirez la batterie en débranchant le

connecteur rapide.

Avertissement : Exposition aux produits chimiques :

Si la batterie fuit, ne laissez pas le liquide entrer en

contact avec la peau ou les yeux. En cas de contact,

lavez la zone aectée à grande eau et consultez un

médecin. Placez la batterie (la batterie usagée incluse

FRANÇAIS (Traduction des instructions d'origine)

Stockage de la batterie

Si vous rangez le robot hors de la station de charge,

retirez d'abord la batterie. Rangez ensuite le robot et la

batterie dans un endroit frais et sec.

Le symbole sur le produit ou son emballage

indique :

Ne pas jeter les appareils électriques avec les déchets

municipaux non triés, utiliser les installations de collecte

sélective. Contactez les autorités locales pour obtenir

des informations sur les systèmes de collecte

disponibles. Si les appareils électriques sont jetés dans

des décharges ou des dépotoirs, des substances

dangereuses peuvent s'inltrer dans la nappe

phréatique et entrer dans la chaîne alimentaire, nuisant

ainsi à votre santé et à votre bien-être. Veuillez contacter

votre autorité locale ou régionale de gestion des

déchets pour plus d'informations sur les programmes

de collecte, de réutilisation et de recyclage.

• Si la pièce à nettoyer comporte un balcon, une

barrière physique doit être mise en place pour

empêcher l'accès au balcon et garantir la sécurité.

• Ne placez aucun objet sur votre robot.

• N'oubliez pas que le robot se déplace seul. Faites

attention lorsque vous marchez dans la zone où

fonctionne le robot an d'éviter de marcher dessus.

• N'utilisez pas le robot dans des zones où des prises

électriques sont posées au sol.

• N'utilisez pas cet appareil sur un sol non ﬁni, non

scellé, ciré ou rugueux. Le sol et l'appareil risquent

d'être endommagés. N'utilisez l'appareil que sur

des sols durs ou des moquettes à poils ras.

• Cet appareil a été conçu pour être utilisé sur des

sols sans les rayer. Nous vous recommandons

néanmoins de tester l'appareil sur une petite partie

de la pièce à nettoyer pour vous assurer qu'il n'y a

pas de rayures avant de nettoyer toute la pièce.

• Lorsque l'appareil n'est pas utilisé, réglez le bouton

d'alimentation situé en bas de l'appareil sur OFF,

an d'éviter que la batterie ne se décharge.

• Chargez votre robot pendant 6 heures avant la

première utilisation.

Batterie et chargement / Informations

Batterie au lithium-ion

Important : Les batteries au lithium-ion et les produits

contenant du lithium-ion sont soumis à des

réglementations strictes en matière de transport. Si

vous devez expédier ce produit (avec la batterie

incluse) à des ns de service, de voyage ou pour toute

autre raison, vous DEVEZ respecter les instructions

d'expédition suivantes :

• Retirez la batterie lithium-ion du produit.

• Placez un morceau de ruban adhésif sur les

contacts de charge métalliques de la batterie.

• Réinstallez la batterie (avec le ruban adhésif) dans

le produit et xez le couvercle de la batterie.

• Emballez le produit dans son emballage d'origine

ou dans votre propre emballage qui empêche tout

mouvement pendant le transport

• Expédiez le produit par voie terrestre uniquement

(pas d'expédition par avion).

FRANÇAIS

(Traduction des instructions d'origine)

1À propos de votre robot

1.1 Robot

Pare-chocs

Capteurs anticollision

Capteurs antichute

Broches de contact de charge

Roue pivotante

Brosses latérales

Batterie

Brosse tournante

Roues

Interrupteur d'alimentation

Bac à poussière

Bouton de la station de charge

Pour renvoyer le robot à la station de

charge, appuyez sur le robot ou sur

la télécommande.

Bouton de démarrage/arrêt

du nettoyage automatique

Appuyez sur ce bouton pour démarrer

ou interrompre le nettoyage.

Lampe DEL

Fond

OFF

FRANÇAIS

FRANÇAIS (Traduction des instructions d'origine)

1.2 Accessoires

1.3 Station de charge

Station de charge Adaptateur Brosse de nettoyage

Bac à poussière

4 x brosses latérales

Bande de délimitation

Brosse tournante 2 x chiffons de nettoyage

Zone de transmission des signaux

Indicateur de charge

Broches de contact de charge

Réservoir d'eau Filtre éponge et filtre

à haute efficacité

FRANÇAIS

Page is loading ...

BLACK+DECKER BRVA425B00 User manual

Brand: BLACK+DECKER

Model: BRVA425B00

Category: Robotic vacuum cleaners

Type: User manual

This manual is also suitable for

BRVA425B10

Download PDF

report

in other languages

français: BLACK+DECKER BRVA425B00 Manuel utilisateur

BLACK+DECKER BRVA425B00 User manual

This manual is also suitable for

BLACK+DECKER BRVA425B00 User manual

in other languages

Related papers

Other documents